MP7705 12v, 2x5w/2x2.5w class?d stereo single ended audio amplifier MP7705 rev. 1.1 www.monolithicpower.com 1 9/18/2009 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2009 mps. all rights reserved. the future of analog ic technology description the MP7705 is a stereo 2x5w/2x2.5w class?d audio amplifier. it is one of mps? second generation fully integrated audio amplifiers which dramatically reduces solution size by integrating the following: z 250m ? power mosfets z startup / shutdown pop elimination z short circuit protection z mute / standby the MP7705 utilizes a single ended output structure capable of delivering 2x5w into 4 ? or 2x2.5w into 8 ? speakers. mps class?d audio amplifiers exhibit the high fidelity of a class a/b amplifier at efficiencies greater than 90%. the circuit is based on the mps? proprietary variable frequency topology that delivers low distortion, fast response time and operates on a single power supply. features ? 2x2.5w output at v dd = 12v (8 ? load) ? 2x5w output at v dd = 12v (4 ? load) ? thd+n = 0.06% at 1w, 8 ? ? 95% efficiency at 2.5w ? low noise (190 v typical) ? switching frequency up to 1mhz ? 9.5v to 12v single-supply operation ? integrated startup and shutdown pop elimination circuit ? thermal and short circuit protection ? integrated 250m ? switches ? mute/standby modes (sleep) ? thermally enhanced 20-pin tssop package with exposed pad applications ? surround sound dvd systems ? televisions ? flat panel monitors ? multimedia computers ? home stereo systems ?mps? and ?the future of analog ic technology? are registered trademarks of monolithic power systems, inc. aam (analog adaptive modulation) is a trademark of monolithic power systems, inc. typical application MP7705 bs1 sw1 bs2 sw2 ref1 2 v dd 3 8 ch1 input 7 6 10 4 9 ch1 output ch2 output 14 18 20 13 15 12 19 17 in1 ref2 in2 en2 en1 agnd2 agnd1 pgnd2 vdd2 v dd ch2 input en pgnd1 vdd1
MP7705 ? 12v, 2x5w/2x2.5w class?d st ereo single ended audio amplifier MP7705 rev. 1.1 www.monolithicpower.com 2 9/18/2009 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2009 mps. all rights reserved. package reference 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 part number* package temperature MP7705df tssop20f ?40 c to +85 c * for tape & reel, add suffix ?z for lead free, add suffix ?lf absolute maxi mum ratings (1) supply voltage v dd ...................................... 16v bs voltage.................. v sw ? 0.3v to v sw + 6.5v enable voltage v en ........................ ?0.3v to +6v v sw , v pin , v nin ........................... ?1v to v dd + 1v agnd to pgnd .......................... ?0.3v to +0.3v junction temperature............................... 150 c lead temperature ....................................260 c storage temperature ..............?65 c to +150 c recommended operating conditions (2) supply voltage v dd .......................... 9.5v to 12v operating temperature t a .........?40 c to +85 c thermal resistance (3) ja jc tssop20f ............................. 40 ....... 6.... c/w notes: 1) exceeding these ratings may damage the device. 2) the device is not guaranteed to function outside of its operating conditions. 3) measured on approximately 1? square of 1 oz copper. electrical characteristics v dd = 12v, v en = 5v, t a = +25 c, unless otherwise noted. parameters symbol condition min typ max units supply current standby current v en = 0v 2 10 a quiescent current 3 6 ma output drivers sw on resistance sourcing and sinking 0.25 ? short circuit current sourcing and sinking 4.0 a inputs ref1/2, in1/2 input common mode voltage range 0 v dd 2 v dd ? 1.5 v ref1/2, in1/2 input current v pin = v nin = 6v 1 5 a v en rising 1.4 2.0 v en enable threshold voltage v en falling 0.4 1.2 v en enable input current v en = 5v 1 a thermal shutdown thermal shutdown trip point t j rising 150 c thermal shutdown hysteresis 30 c
MP7705 ? 12v, 2x5w/2x2.5w class?d st ereo single ended audio amplifier MP7705 rev. 1.1 www.monolithicpower.com 3 9/18/2009 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2009 mps. all rights reserved. operating specifications circuit of figure 1, v dd = 12v, v en = 5v, t a = +25 c, unless otherwise noted. parameters symbol condition min typ max units power output f = 1khz, thd+n = 10%, 8 ? load 2.5 w thd+ noise p out = 1w, f = 1khz, 8 ? load 0.06 % efficiency f = 1khz, p out = 1w, 8 ? load 87 % maximum power bandwidth 20 khz dynamic range 87 db noise floor a-weighted 190 v power supply rejection f = 1khz 60 db pin functions pin # name description 1, 5, 11, 16 nc no connect. not internally connected 2 ref1 amplifier 1 reference. ref1 is the reference point for amplifier 1. use a resistive voltage divider to set the voltage at ref1 to v dd /2. 3 in1 amplifier 1 input. in1 is the inverting input for amplifier 1. 4 agnd1 analog ground 1. connect agnd1 to agnd2. 6 en1 enable input 1. en1 must be connected to en 2. drive en1 high to enable MP7705; low to disable it. 7 in2 amplifier 2 input. in2 is the inverting input for amplifier 2. 8 ref2 amplifier 2 reference. ref2 is the reference point for amplifier 2. use a resistive voltage divider to set the voltage at ref1 to v dd /2. 9 agnd2 analog ground 2. connect agnd2 to agnd1. 10 en2 enable input 2. en2 must be connected to en1. drive high to enable MP7705, drive low to disable. 12 bs2 high-side mosfet bootstrap input for amplifie r 2. a capacitor from bs2 to sw2 supplies the gate drive current to the internal high-side mosfet. connect a 1 f capacitor from sw2 to bs2. 13 vdd2 power supply input. bypass vdd2 to pgnd2 with a 1 f x7r capacitor (in addition to the main bulk capacitor), placed close to the ic pin13 and pin15. 14 sw2 switched power output. sw2 is the output of amplifier 2. connect the lc filter to this pin. 15 pgnd2 power ground for amplifier 2. connect pgnd2 to pgnd1. 17 bs1 high-side mosfet bootstrap input for amplifie r 1. a capacitor from bs1 to sw1 supplies the gate drive current to the internal high-side mosfet. connect a 1 f capacitor from sw1 to bs1. see figure 1. 18 vdd1 power supply input. bypass vdd1 to pgnd1 with a 1 f x7r capacitor (in addition to the main bulk capacitor), placed close to the ic pin18 and pin20. 19 sw1 switched power output. sw1 is the output of amp lifier 1. connect the lc filter to this pin. see figure 1. 20 pgnd1 power ground for amplifier 1. connect pgnd1 to pgnd2. see figure 1.
MP7705 ? 12v, 2x5w/2x2.5w class?d st ereo single ended audio amplifier MP7705 rev. 1.1 www.monolithicpower.com 4 9/18/2009 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2009 mps. all rights reserved. typical performanc e characteristics v dd =12v, r load =8 ? , a v =8.2, t a = +25oc, unless otherwise noted.
MP7705 ? 12v, 2x5w/2x2.5w class?d st ereo single ended audio amplifier MP7705 rev. 1.1 www.monolithicpower.com 5 9/18/2009 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2009 mps. all rights reserved. operation the MP7705 uses monolithic power systems? patented analog adaptive modulation tm to convert the audio input signal into pulses of power that, when filtered through an external inductor-capacitor filter, reproduce the amplified signal across the load. because of the switching class?d output stage, power dissipation in the amplifier is drastically reduced when compared to class a or a/b amplifiers while providing high fidelity and low distortion. the voltage gain is set by the combination of the input resistor r in and the feedback resistor r fb and is calculated by the equation: in fb v r r a ? = where for channel 1: r fb =r fb1 and r in =r in1 and for channel 2: r fb =r fb2 and r in =r in2 . the MP7705 includes four high-power mosfets wherein for each channel the output driver stage uses two 250m ? n-channel mosfets to deliver the pulses to the lc output filter that in turn drives the load. to fully enhance the high-side mosfet, the gate is driven to a voltage higher than v dd by the bootstrap capacitor between sw and bs. while the output is driven low, the bootstrap capacitor is charged from v dd . the gate of the high-side mosfet is driven high from the voltage at bs, forcing the mosfet gate to a voltage higher than v dd and allowing the mosfet to fully turn on, reducing power loss in the amplifier. pop elimination the capacitors c out1 and c out2 block the dc signal and pass only the ac signals to the load. to insure that the amplifier passes low frequency signals, the capacitor values need to be chosen such that the time constant of c out x r load is long. during startup, these capacitors need to be charged up to the dc operating point, which is typically at ? of v dd . the MP7705 includes special integrated circuitry that carefully controls the pre-charging of these capacitors, eliminating the turn-on and turn-off pop normally associated with the charging of the ac coupling capacitors. short circuit/overload protection the MP7705 has internal overload and short circuit protection. the currents in both the high-side and low-side mosfets are measured and if the current exceeds the 4.0a short circuit current limit, both mosfets are turned off. the MP7705 then restarts with the same power up sequence that is used for normal starting to prevent a pop from occurring after a short circuit condition is removed. mute/enable function the MP7705 en inputs are active high enable controls. to enable the MP7705, drive en with a 2.0v or higher voltage. to disable the amplifier, drive en below 0.4v. while the MP7705 is disabled, the v dd operating current is less than 10 a and the output driver mosfets are turned off. the MP7705 requires approximately 500ms from the time that en is asserted (driven high) to when the amplifier begins normal operation.
MP7705 ? 12v, 2x5w/2x2.5w class?d st ereo single ended audio amplifier MP7705 rev. 1.1 www.monolithicpower.com 6 9/18/2009 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2009 mps. all rights reserved. application information component selection the MP7705 uses a minimum number of external components to complete a stereo class?d audio amplifier. the circuit of figure 1 is optimized for a 12v power supply and a 1.5v rms maximum input signal. this circuit should be suitable for most applications. however, if this circuit is not suitable, use the following sections to determine how to customize the amplifier for a particular application. setting the voltage gain the maximum output voltage swing is limited by the power supply. to achieve the maximum power out of the MP7705 amplifier, the gain resistors should be set such that the maximum input signal results in an output voltage swing that reaches the supply limit (clipping). the maximum output voltage swing at clipping is approximately v dd /2. to achieve clipping for a given input signal voltage, where v in(pk) is the peak input voltage, the voltage gain is: ) pk ( v 2 v ) max ( a in dd v = the voltage gain setting results in the peak output voltage approaching its maximum for the maximum input signal. there are applications where it is desirable to allow the amplifier to overdrive slightly, allowing the thd to increase at higher power levels (as the output signal continues to go further into clipping), and so a higher gain than a v (max) is required. setting the switching frequency the idle switching frequency (the switching frequency when no audio input is present) is a function of several variables: the supply voltage v dd , the timing capacitor c int and the feedback resistor r fb . for the MP7705, the idle switching frequencies for ch1 and ch2 are independent of each other and are a function of their own associated components. the proper setting of the ?idle frequency? is important for obtaining optimum performance. if the frequency is set too high, the result will be more power loss and high distortion, while setting the idle switching frequency too low results in more inductor ripple, causing more output voltage ripple with increased the output noise. the optimum quiescent switching frequency is approximately 700khz to 800khz. refer to table 1 for recommended values. table 1?switching frequency vs. v dd , timing capacitor and feedback resistor (see figure 1) gain (v/v) gain (db) r fb (k ? ) r in (k ? ) c int f sw v dd (v) 3.9 11.8 39 10 6.8nf 660khz 12 8.2 18.3 82 10 3.3nf 660khz 12 8.3 18.4 39 4.7 6.8nf 660khz 12 17.4 24.8 82 4.7 3.3nf 660khz 12 choosing the lc filter the inductor-capacitor (lc) filter converts the pulse train at sw to the output voltage that drives the speaker. typical values for the lc filter are a 10 h inductor and a 0.47 f capacitor. the characteristic frequency of the lc filter needs to be high enough to allow high frequency audio to the output, yet needs to be low enough to filter out high frequency products of the pulses from sw. the characteristic frequency of the lc filter is: lc 2 1 f 0 = the voltage ripple at the output is approximated by the equation: ? ? ? ? ? ? ? ? ? sw 0 dd ripple f f v v
MP7705 ? 12v, 2x5w/2x2.5w class?d st ereo single ended audio amplifier MP7705 rev. 1.1 www.monolithicpower.com 7 9/18/2009 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2009 mps. all rights reserved. the quality factor (q) of the lc filter is important. if this is too low output noise will increase, and if this is too high then peaking may occur at high signal frequencies reducing the passband flatness. the circuit q is set by the load resistance (speaker resistance, typically 8 ? ) and is calculated as: r l f 2 r l q 0 0 = = where 0 is the characteristic frequency in radians per second and f 0 is in hz. use a lc filter with q between 0.7 and 2. the actual output ripple and noise is greatly affected by the type of inductor and capacitor used in the lc filter. use a film capacitor and an inductor with sufficient power handling capability to supply the output current to the load. the inductor should exhibit soft saturation characteristics. if the inductor exhibits hard saturation, it should operate well below the saturation current. gapped ferrite, mpp, powdered iron or similar type toroidal cores are recommended. if open or shielded bobbin ferrite cores are used for multi-channel designs, make sure that the start windings of each inductor line up (all starts going toward sw pin or all starts going toward the output) to prevent crosstalk or other channel-to-channel interference. output coupling capacitors the output ac coupling capacitors c out1 and c out2 serve to block dc voltages and thus pass only the amplified ac signal from the lc filter to the load. the combination of the coupling capacitor and the load resistance results in a first-order high-pass filter. the values of c out1 and c out2 should be selected such that the required minimum frequency is still allowed to pass. the output corner frequency (-3db point), f out , can be calculated as: out load out c r 2 1 f = set the output corner frequency at or below the minimum required frequency. the output coupling capacitor carries the full load current, so the capacitor should be chosen such that its ripple current rating is greater than the maximum load current. low esr aluminum electrolytic capacitors are recommended. input coupling capacitors the input coupling capacitors c in1 and c in2 are used to pass only the ac signal at the input. in a typical system application, the source input signal is typically centered around the circuit ground, while the MP7705 input is at half the power supply voltage (v dd /2). the input coupling capacitors transmit the ac signal from the source to the MP7705 while blocking the dc voltage. choose the input coupling capacitors such that the corner frequency (f in ) is less than the passband frequency. the corner frequency is calculated as: in in in c r 2 1 f = power source for maximum output power, the amplifier circuit requires a regulated external power source to supply the power to the amplifier. a higher power supply voltage allows more power to be delivered to a given load resistance. it is very important to bypass the power supply pins with 1f x7r ceramic capacitors. power supply pumping it is also very important to bypass the power supply with a large aluminum electrolytic capacitor. it is recommended to use a value of at least 1000f. this is necessary to prevent the supply voltage from getting pumped up to a level that exceeds the absolute maximum rating. supply pumping occurs in single-ended class? d amplifiers, and is caused by rapid switch transitions where current is pumped back up into the supply line. the large capacitor is necessary to absorb this current and prevent v dd from rising too high.
MP7705 ? 12v, 2x5w/2x2.5w class?d st ereo single ended audio amplifier MP7705 rev. 1.1 www.monolithicpower.com 8 9/18/2009 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2009 mps. all rights reserved. pcb layout the circuit layout is critical for optimum performance and low output distortion and noise. place the following components as close to the MP7705 as possible: power supply bypass, c byp c byp1 and c byp2 carry the transient current for the switching power stage. to prevent overstressing of the MP7705 and excessive noise at the output, place c byp1 as close to pins 18 (vdd1) and 20 (pgnd1) as possible and also place c byp2 as close to pins 13 (vdd2) and 15 (pgnd2) as possible. output catch diodes d sh1 , d sl1 , d sh2 and d sl2 carry the current over the dead-time while the mosfet switches are off. place the diodes as close to the MP7705 as possible. timing capacitors c int1 and c int2 are used to set the amplifier switching frequencies and are typically on the order of a few nf. place c int1 as close to pins 2 and 3 as possible to reduce distortion and noise. likewise, place c int2 as close to pins 7 and 8 as possible. reference bypass capacitors c r1 and c r2 filter the ? v dd reference voltages. place c r1 and c r2 as close to the ic as possible to improve power supply rejection and reduce distortion and noise at the output. when laying out the pcb, use two separate ground planes, analog ground (agnd) and power ground (pgnd), and connect the two grounds together at a single point to prevent noise injection into the amplifier input to reduce distortion. make sure that any traces carrying the switch node (sw) voltages are separated far from any input signal traces. if it is required to run the sw trace near the input, shield the input with a ground plane between the traces. for multiple channel applications, make sure that each channel is physically separated to prevent crosstalk. make sure that all inductors used on a single circuit board have the same orientation. also, make sure that the power supply is routed from the source to each channel individually, not serially. this prevents channel-to-channel coupling through the power supply input. electro-magnetic interference (emi) considerations due to the switching nature of the class?d amplifier, care must be taken to minimize the effects of electromagnetic interference from the amplifier. however, with proper component selection and careful attention to circuit layout, the effects of the emi due to the amplifier switching can be minimized. the power inductors are a potential source of radiated emissions. for the best emi performance use toroidal inductors, since the magnetic field is well contained inside the core. however toroidal inductors can be expensive to wind. for a more economical solution, use shielded gapped ferrite or shielded ferrite bobbin core inductors. these inductors typically do not contain the field as well as toroidal inductors, but usually can achieve a better balance of good emi performance with low cost. the size of high-current loops that carry rapidly changing currents needs to be minimized. to do this, make sure that the v dd bypass capacitors and the schottky catch diodes are as close to the MP7705 as possible. nodes that carry rapidly changing voltages, such as sw, need to be made as small as possible. if sensitive traces run near a trace connected to sw, place a ground shield between the traces.
MP7705 ? 12v, 2x5w/2x2.5w class?d st ereo single ended audio amplifier MP7705 rev. 1.1 www.monolithicpower.com 9 9/18/2009 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2009 mps. all rights reserved. typical application circuit MP7705 bs1 sw1 bs2 sw1 ref1 2 v dd v dd 3 8 ch1 input 7 6 10 4 9 ch1 output ch2 output 14 18 20 13 15 12 19 17 in1 ref2 in2 en2 en1 agnd2 agnd1 pgnd2 vdd2 v dd c byp2 c byp1 c vddbyp d sl2 d sl1 c f1 c out1 l f1 l f2 c out2 c f2 v dd v dd r bs1 r bs2 c bs2 c bs1 c fb1 r fb1 d bs1 d bs3 d bs4 d bs2 ch2 input en pgnd2 vdd2 c fb2 r fb2 c in2 r in2 c in1 r in1 c r2 c int2 r rl2 r rh2 c r1 c int1 r rl1 r rh1 figure 1?2x2.5w stereo typical application circuit
MP7705 ? 12v, 2x5w/2x2.5w class?d st ereo single ended audio amplifier notice: the information in this document is subject to change wi thout notice. please contact m ps for current specifications. users should warrant and guarantee that third party intellectual property rights ar e not infringed upon when integrating mps products into any application. mps will not assume any legal responsibility for any said applications. MP7705 rev. 1.1 www.monolithicpower.com 10 9/18/2009 mps proprietary information. unaut horized photocopy and duplication prohibited. ? 2009 mps. all rights reserved. package information tssop20f (exposed pad) 0.19 0.30 6.40 6.60 seating plane 0.65 bsc pin 1 id 4.30 4.50 6.20 6.60 110 11 20 0.80 1.05 1.20 max 0.00 0.15 0.09 0.20 2.60 3.10 3.80 4.30 5.80 typ 1.60 typ 0.40 typ 0.65 bsc 3.20 typ 4.40 typ 0.45 0.75 0 o -8 o 0.25 bsc gauge plane
|
