View LTL30ESCBKJH96_8991586.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lite-on dcc release lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL30ESCBKJH96 spec no.: ds20-2013-0241effective date: 09/12/2013revision: - bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y features * lead (pb) free product C rohs compliant. * halogen free product (cl < 900 ppm, br < 900 ppm, and cl + br < 1500 ppm ). * designed for ease in circuit board assembly. * black case enhance contrast ratio. * solid state light source. * reliable and rugged. package dimensions part no. lens source color LTL30ESCBKJH96 white diffused ingan blue / alingap yellow notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm(.010") unless otherwise noted. 3. the holder (housing) is 46l096, pc black. 4. the led lamp is ltl30escbkj - hf. 5. specifications are subject to change without notice. part no. : LTL30ESCBKJH96 page : 1 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y absolute maximum ratings at t a =25 c parameter inga n blue allngap yellow unit power dissipation 123 75 mw peak forward current (1/10 duty cycle, 0.1ms pulse width) 60 60 ma dc forward current 30 30 ma operating temperature range - 4 0 c to + 8 5 c storage temperature range - 40 c to + 100 c lead soldering temperature [2.0 mm(.0 78 ") from body] 260 c for 5 seconds max. part no. : LTL30ESCBKJH96 page : 2 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y electrical / optical characteristics at t a =25 c parameter symbol color min. typ. max. unit test condition luminous intensity i e blue yellow 110 180 240 350 520 880 mcd i f = 20ma i f = 20ma note 1,4 viewing angle 2 1/2 blue yellow 40 40 deg note 2 (fig. 5 ) peak emission wavelength p blue yellow 468 591 nm measurement @peak (fig.1) dominant wavelength d blue yellow 464 582 470 589 475 596 nm note 3 spectral line half - width ? blue yellow 22 20 nm forward voltage v f blue yellow 3.2 2. 1 4.0 2. 5 v i f = 20ma reverse current i r blue yellow 10 0 a v r = 5v , note 5 note: 1. luminous intensity is measured with a light sensor and filter combination that approximates the cie (commission international de l'eclairage) eye - response curve. 2. 1/2 is the off - axis angle at which the luminous intensity is half the axial luminous intensity. 3. the dominant wavelength, d is derived f rom the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 4. the iv guarantee should be added 30 %. 5. reverse voltage (v r ) condition is applied for ir test only. the device is not designed for reverse operation. part no. : LTL30ESCBKJH96 page : 3 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y typical electrical / optical characteristics curves (25 c ambient temperature unless otherwise noted) part no. : LTL30ESCBKJH96 page : 4 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y packing spec 250 pcs or 100 pcs per packing bag 12 packing bags per inner carton total 3 , 000 pcs per inner carton 8 inner cartons per outer carton total 2 4 , 000 pcs per outer carton in every shipping lot, only the last pack will be non - full packing part no. : LTL30ESCBKJH96 page : 5 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y bin table for reference bin co de luminous intensity ( blue ) unit : mcd @20ma bin co de luminous intensity ( yellow ) unit : mcd @20ma min. max. min. max. fg 110 180 hj 180 310 hj 180 310 kl 310 520 kl 310 520 mn 5 20 880 note: to lerance of each bin limit is 30 % bin co de dominant wavelengt h (blue) unit : nm @20ma bin co de dominant wavelengt h (yellow) unit : nm @20ma min. max. min. max. 1 464.0 470.0 3 582.0 589.0 2 470.0 475.0 4 589.0 596.0 note: tolerance of each bin limit is 1nm bin code list category code fg 1 hj 3 luminous intensity ( blue ) dominant wavelengt h (blue) luminous intensity ( yellow ) dominant wavelengt h (yellow) part no. : LTL30ESCBKJH96 page : 6 of 1 0 bns - od - c131/a 4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y cautions 1. application the leds described here are intended to be used for ordinary electronic equipment (such as office equipment, communication equipment and household applications).consult liteons sales in advance for information on applications in which exceptional reliability is required, particularly when the failure or malfunction of the leds may directly jeopardize life or health (such as in aviation, transportation, traffic control equipment, medical and life support systems and safety devices). 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative humidity. it is recommended that leds out of their original packaging are used within three months. for ext ended storage out of their original packaging, it is recommended that the leds be stored in a sealed container with appropriate desiccant or in desiccators with nitrogen ambient. 3. cleaning use alcohol - based cleaning solvents such as isopropyl alcohol to clean the leds if necessary. 4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of led lens. do not use the base of the lead frame as a fulcrum during forming. lead forming must be done before so ldering, at normal temperature. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 5. soldering when soldering, leave a minimum of 2mm clearance from the base of the lens/holder to the soldering point. dip ping the lens/holder into the solder must be avoided. do not apply any external stress to the lead frame during soldering while the led is at high temperature. recommended soldering conditions : soldering iron wave soldering temperature soldering time 3 5 0c max. 3 sec. max. (one time only) pre - heat pre - heat time solder wave soldering time 100c max. 60 sec. max. 260c max. 5 sec. max. note: excessive soldering temperature and/or time might resul t in deformation of the led/holder o r catastrophic failure of the cbi. ir(hot air) re - flow is not suitable process for through hole type led lamp production. max. temperature of wave soldering is not mean that holder s hdt/melting temperature. part no. : LTL30ESCBKJH96 page : 7 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y 6. drive method an led is a current - operated device. in order to ensure intensity uniformity on multiple leds connected in parallel in an application, it is recommended that a current limiting resistor be incorpora ted in the drive circuit, in series with each led as shown in circuit a below. circuit model a circuit model b (a) recommended circuit (b) the brightness of each led might appear different due to the differences in the i - v characteristics of those leds 7. esd (electrostatic discharge) s tatic electricity or power surge will damage the led. suggestions to prevent esd damage: ? use a conductive wrist band or anti - electrostatic glove when handling these leds ? all devices, equipment, and machinery must be properly grounded ? work tables, storage racks, etc. should be properly grounded ? use ion blower to neutralize the static charge which might have built up on surface of the leds plastic lens as a result of friction between leds during storage and handing part no. : LTL30ESCBKJH96 page : 8 of 10 bns - od - c131/a4 led led
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y suggested checking list : training and certification 1. everyone working in a static - safe area is esd - certified? 2. training records kept and re - certification dates monitored? static - safe workstation & work areas 1. static - safe workstation or work - areas have esd signs? 2. all surfaces and objects at all static - safe workstation and within 1 ft measure less than 100v? 3. all ionizer activated, positioned towards the units? 4. each work surface mat s grounding is good? personnel grounding 1. every person (including visitors) handling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 2. if conductive footwear used, conductive flooring also presen t where operator stand or walk? 3. garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 4. every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dl s ? 5. all wrist strap or heel strap checkers calibration up to date? note: *50v for blue led. device handling 1. every esds items identified by eia - 471 labels on item or packaging? 2. all esds items completely inside properly closed static - shielding containers when not at sta tic - safe workstation? 3. no static charge generators (e.g. plastics) inside shielding containers with esds items? 4. all flexible conductive and dissipative package materials inspected before reuse or recycle? others 1. audit result reported to entit y esd control coordinator? 2. corrective action from previous audits completed? 3. are audit records complete and on file? part no. : LTL30ESCBKJH96 page : 9 of 10 bns - od - c131/a4
lite - on technology corporation p r o p e r t y o f l i t e - o n o n l y 8 . reliability test classificati on test item test condition reference standard endurance test operation life (lt) ta = under room temperature if = per datasheet maximum drive current *test time = 1000 hrs mil - std - 750d:1026 (1995) mil - std - 883g:1005 (2006) high temperature/ h igh humidity storage (thb) ta = 60 c rh = 90% test time = 240hrs mil - std - 202g:103b (2002) jeita ed - 4701:100 103 (2001) high temperature storage ta = 105 5c test time = 1000 hrs mil - std - 750d:1031 (1995) mil - std - 883g:1008 (2006) jeita ed - 4701:200 201 (2001) low temper ature storage ta= - 55 5c test time = 1000 hrs jeita ed - 4701: 200 202 (2001) environmental test temperature cycling 100c ~ 25c ~ - 40c ~ 25c 30 mins 5 mins 30 mins 5 mins 30 cycles mil - std - 750d:1051 (1995) mil - std - 883g:1010 (2006) j eita ed - 4701:100 105 (2001) jesd22 - a104c (2005) thermal shock 100 5c ~ - 30 5c 15 mins 15 mins 30 cycles (< 20 secs transfer) mil - std - 750d:1056 (1995) mil - std - 883g:1011 (2006) mil - std - 202g:107g (2002) jesd22 - a106b (2004) solder r esistance (no pre - condition) t.sol = 260 5c dwell time = 10 1 sec mil - std - 750d:2031 (1995) jeita ed - 4701: 300 302 (2001) solder ability (no pre - condition) t.sol = 245 5c dwell time = 5 0.5 sec mil - std - 750d:2026 (1995) mil - std - 883g:2003 (2 006) mil - std - 202g:208h (2002) ipc/eia j - std - 002 (2004) soldering iron (no pre - condition) t.sol = 350 5c dwell time = 3.5 0.5 sec mil - std - 202g:208h (2002) jeita ed - 4701: 300 302 (2001) 9. others the appearance and specifications of the pr oduct may be modified for improvement, without prior notice. part no. : LTL30ESCBKJH96 page : 10 of 10 bns - od - c131/a4

▲Up To Search▲

Price & Availability of LTL30ESCBKJH96

	To Download LTL30ESCBKJH96 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .