View N6155A_8984388.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

keysight technologies isdb-t/ tmm x-series measurement application N6155A & w6155a technical overview
introduction C measure isdb-t or isdb-tmm rf transmitter, modulator, gap-fller, tuner, or amplifer performance C auto-detect the isdb-t demodulation parameters and display in the tmcc decoding view; auto-detect and show the isdb-tmm confguration by super segment C single frequency network measurement (supports pre-, post-, 0-db, and out-of-gi echo scenarios) C show the ac (auxiliary channel) decoded bits in ac decoding results view C perform one-button tests with pass/fail limit per isdb-t and isdb-t sb standards C use hardkey/softkey manual user interface or scpi remote control C leverage built-in context sensitive help C move application between x-series signal analyzers with transportable licensing
03 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview ports, enable you to keep your test assets current and extend instrument longev - ity. proven algorithms, 100% code- compatibility, and a common ui across the x-series create a consistent measure - ment framework for signal analysis that ensures repeatable results and measure - ment integrity so you can leverage your test system software through all phases of product development. in addition to fxed, perpetual licenses for our x-series measurement applications, we also offer transportable licenses which can increase the value of your investment by allowing to you transport the application to multiple x-series analyzers. key parameter setup C radio standard: isdb-t, or isdb-t sb , and isdb-tmm C channel bandwidth: 6/ 7/ 8 mhz for isdb-t; 14.5 mhz for isdb-tmm C segment number: 13 segments for isdb-t, 1 or 3 segments for isdb- t sb , 33 segments for isdb-tmm C fft mode: 2k, 4k or 8k C guard interval: 1 /4, 1 /8, 1/16, 1/32 C partial reception: on/off C modulation: qpsk/16qam/64qam C input: rf or analog iq (only available in the n9030a pxa or n9020a mxa) for signal quality and modulation ac - curacy measurements the isdb-t/tmm measurement applica - tion provides one-button, standard-based power and modulation analysis capabili - ties to help you with designing, evaluating, and manufacturing isdb-t modulators, transmitters, amplifers, tuners, and gap- fllers/repeaters. used with the optional analog baseband iq inputs in the pxa or mxa signal analyzer, it can provide you the fexibility of measuring signal quality and modulation accuracy with rf input or analog iq input. the isdb-t/tmm measurement applica - tion is just one in a common library of more than 25 measurement applications in the keysight technologies, inc. x- series, an evolutionary approach to signal analysis that spans instrumentation, measurements, and software. the x-series analyzers, with upgrade - able cpu, memory, disk drives, and i/o isdb-t/tmm measurement application
04 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview isdb-t, isdb-t sb and isdb-t b integrated services digital broadcasting (isdb) is a japanese standard for digital television (dtv) and digital radio used by the country's radio and television stations. isdb-t and isdb-t sb standards are the digital terrestrial broadcasting systems developed by japans association of radio industries and business (arib). isdb-t, as a terrestrial broadcasting system, has also been adopted by brazil, where it is called isdb-t b . isdb-t and isdb-t b both use an identical physical layer. isdb-t sb is used for audio and data program trans - missions. the system and specifcations of isdb-t sb are similar to isdb-t, except that the bandwidth is narrower and there are only one or three segments in the channel. keysights isdb-t measurement applica - tion supports measurement on both isdb- t and isdb-t sb standards. isdb-tmm and ac the new vhf band, 207.5 to 222 mhz, introduced in 2011, after the analog tv switch-off in japan. the government announced that isdb-tmm (terrestrial mobile multimedia) will be used for new multimedia service in this band. the isdb- tmm standard employs the concatenated transmission method which, combining blocks of the 13-segment (type a) and the 1-segment (type b), eliminates the need for a guard band, making it possible to apply it to various bandwidths. figure 2 is an example of isdb-tmm frame structure consisting of two type a super segments and one type b super segment. auxiliary channel (ac) is used to convey additional information on modulation signal-transmission control, or earthquake alarm information. the earthquake infor - mation is transmitted using the ac of the center segment (segment no. 0). figure 1. hierarchical transmission and partial reception in isdb-t segment and layer in isdb-t isdb-t supports hierarchical transmis - sion by introducing hierarchical layers, which means different services such as hdtv, multi-channel sdtv, and data, can be transmitted in one frequency channel. there are 13 ofdm segments in the isdb- t transmission channel. each layer consists of one or more segments which have their own transmission parameters (such as the inner coding rate, modulation scheme, and time interleaving length). a maximum of three layers can be provided, defned as layer a, b, and c. partial reception isdb-t also supports partial receptions. partial reception refers to the segment at the center of the transmission system. the range of frequency interleaving can be limited within the segment, so that narrow band (1-seg) receiver can receive services contained in the center segment. the gen - eral concept of hierarchical transmission and partial reception is shown in figure 1. isdb-t, isdb-t sb , and isdb-tmm standards overview
05 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview figure 2. isdb-tmm frame confguration table 1. key parameters in isdb-t and isdb-t sb standards isdb-t isdb-t sb isdb-tmm frequency uhf 470 to 770 mhz vhf/uhf vhf: 207.5 to 222 mhz bandwidth 6, 7, 8 mhz 430 khz for 1-segment and 1.3 mhz for 3-segments for 6 mhz system 6 to 14.5 mhz segments 13 segments 1 or 3 segments 13 to 33 segments modulation ofdm ofdm ofdm mode mode 1 /2/3 mode 1 /2/3 mode 1 /2/3 modulation format dqpsk/qpsk/16qam/64qam dqpsk/qpsk/16qam/64qam dqpsk/qpsk/16qam/64qam guard interval 1 /4, 1 /8, 1/16, 1/32 1 /4, 1 /8, 1/16, 1/32 1 /4, 1 /8, 1/16, 1/32 fec inner coding: convolution 1 /2, 2/3, 3 /4, 5/6, 7 /8 outer coding: reed solomon (204, 188) inner coding: convolution 1 /2, 2/3, 3 /4, 5/6, 7 /8 outer coding: reed solomon (204, 188) inner coding: convolution 1 /2, 2/3, 3 /4, 5/6, 7 /8 outer coding: reed solomon (204,188) multiplexing mpeg-2 ts mpeg-2 ts mpeg-2 ts video mpeg-2 video or mpeg-4 avc/h.264 (1-seg) mpeg-2 video or mpeg-4 avc/h.264 (1-seg) mpeg-2 video or mpeg-4 avc/h.264 (1-seg) audio mpeg-2 audio (aac) mpeg-2 audio (aac) mpeg-2 audio (aac) bit rate 3.651 ~ 23.234 mb/s 0.280 ~ 1.787 mb/s other supports partial reception and ac
06 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview table 2. required rf transmitter measurements and the corresponding measurements in n/w6155a jeita handbook v2.2 paragraph # transmitter tes t n/w6155a isdb-t measurement application 4.3.1 frequency deviation spectrum analyzer mode (marker counter function) 4.3.2 signal power channel power 4.3.3 occupied frequency bandwidth occupied bandwidth (bw) 4.3.4 spectrum mask spectrum emission mask 4.3.5 unwanted emissions spectrum analyzer mode (spurious emissions measurement) 4.3.6 ifft sampling frequency deviation spectrum analyzer mode (marker counter function) 4.3.7 phase noise n/w9068a phase noise measurement application 4.3.8 amplitude-frequency characteristics monitor spectrum measurement 4.3.9 group delay characteristics mod accuracy (frequency response view) 4.3.10 delay time n/a 4.3.11 intermodulation monitor spectrum measurement 4.3.12 gaussian noise vs. ber n/a 4.3.13 input electric feld strength vs. ber n/a 4.3.14 power consumption n/a 4.3.15 input signal mod accuracy (tmcc decoding view) 4.3.17 output mismatching range spectrum analyzer mode 4.3.18 mer characteristics mod accuracy (result metrics view) 4.3.19 actual viewing of and listening to video and sound n/a transmitter tests the rf transmitter test requirements for isdb-t are defned in the jeita handbook methods of measurement for digital terrestrial broadcasting transmitters. table 2 shows the required base station rf transmitter tests along with the corresponding mea - surement applications.
07 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview measurement details most of the rf transmitter measurements as defned by the isdb-t standard, as well as a wide range of additional measurements and analysis tools, are available with a press of a button (table 3). these measurements are fully remote controllable via the iec/ieee bus or lan, using scpi commands. analog baseband measurements are available on the keysight pxa or mxa signal ana - lyzer equipped with bbiq hardware. supported baseband measurements include all of the modulation quality plus i/q waveform measurements. table 3. one-button measurements provided by the n/w6155a measurement application technology isdb-t isdb-t sb isdb-tmm measurement application N6155A-2fp, w6155a-2fp N6155A-2fp, w6155a-2fp N6155A-3fp,w6155a-3fp x-series analyzer pxa, mxa, exa, cxa 1 pxa, mxa, exa, cxa 1 pxa, mxa, exa, cxa 1 measurements channel power rf spectrum shoulder attenuation adjacent channel power 2 spectrum emission mask 2 power statistic ccdf spurious emission modulation accuracy rms evm (%) peak evm (%) position of peak evm rms mer (db) peak mer (db) position of peak mer rms mag error (%) peak mag error (%) position of peak mag error rms phase error (deg) peak phase error (deg) position of peak phase error frequency error (hz) tx power (dbm) quadrature error (deg) amplitude imbalance (db) in-band spectrum ripple amax-ac (db) amin-ac (db) mer/evm vs. subcarriers/frequency mer by layer a/b/c (db) mer by data, pilot, tmcc, and ac1 (db) amplitude vs. subcarriers (db) phase vs. subcarriers (deg) group delay vs. subcarriers (ns) spectral fatness (db) tmcc decoding ac decoding isdb-tmm confguration channel impulse response single frequency network (sfn) test (pre-echo, post-echo, 0-db echo, and out-of-gi echo) 1. N6155A operates in the pxa, mxa, and exa signal analyzers. w6155a operates in the cxa signal analyzer. 2. this measurement in isdb-tmm mode requires manual confguration.
08 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview figure 3. isdb-t constellation and mer results figure 4. isdb-t iq quad view figure 5. isdb-t tmcc decoding view figure 6. isdb-t result metrics view figure 7. isdb-t channel impulse response view figure 8. isdb-t shoulder attenuation
09 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview figure 9. isdb-t ac decoding view figure 11. isdb-tmm confguration with type a lowercase segments and super segment figure 10. isdb-tmm mer vs. lowercase segments and super segment figure 12. isdb-tmm confguration with type b lowercase segments and super segment
10 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview key specifcations description pxa mxa exa cxa channel power 5.60 mhz integration bandwidth ?50 dbm (nom) ?50 dbm (nom) ?50 dbm (nom) ?50 dbm (nom) absolute power accuracy 20 to 30 c 0.61 db ( 0.19 db 95%) 0.82 db ( 0.23 db 95%) 0.94 db ( 0.27 db 95%) 1.33 db ( 0.61 db 95%) measurement foor ?87.2 dbm ?84.2 dbm ?80.2 dbm ?77.2 dbm channel power with shoulder attenuation view 5.60 mhz integration bandwidth ml 1 = C14.0 dbm (nom) ml 1 = C16.0 dbm (nom) ml 1 = C16.0 dbm (nom) ml 1 = C15.0 dbm (nom) dynamic range, relative offset frequency 3.4 mhz 92.9 db (98.7 db typ) 87.7 db (94.1 db typ) 82.5 db (89.6 db typ) 78.9 db (86.6 db typ) power statistics ccdf minimum power at rf input ?50 dbm (nom) ?50 dbm (nom) ?50 dbm (nom) ?50 dbm (nom) histogram resolution 0.01 db 0.01 db 0.01 db 0.01 db adjacent channel power minimum power at rf input; 0 to 55 c ?36 dbm (nom) ?36 dbm (nom) ?36 dbm (nom) ?36 dbm (nom) acpr accuracy 5.60 mhz noise bandwidth, method = ibw offset frequency 6 mhz 0.16 db 0.38 db 0.81 db 1.20 db 1. ml (mixer level) is rf input power minus attenuation defnitions C specifcations describe the performance of parameters covered by the product warranty. C 95th percentile values indicate the breadth of the population (2) of performance tolerances expected to be met in 95% of cases with a 95% confdence. these values are not covered by the product warranty. C typical values are designated with the abbreviation typ. these are per - formance beyond specifcation that 80% of the units exhibit with a 95% confdence. these values are not covered by the product warranty. C nominal values are designated with the abbreviation nom. these values indicate expected performance, or describe product performance that is useful in the application of the product, but is not covered by the product warranty. C pxa specifcations apply to analyzers with frequency options of 526 and lower. for analyzers with higher frequency options, specifcations are not warranted but performance will nominally be close to that shown in this section. note: data subject to change you can upgrade! options can be added after your initial purchase. all of our x-series application options are license-key upgradeable. up grade
11 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview description pxa mxa exa cxa spectrum emission mask limit type: manual; jeita(arib-b31) according to p 0.025 w, 0.025 w < p 0.25 w, 0.25 w < p 2.5 w or p > 2.5 w: abnt non-critical; abnt sub-critical; abnt-critical; isdb-t sb 3.0 mhz offset (rbw = 10 khz) dynamic range, relative 93.8 db (99.1 db typ) 87.6 db (93.9 db typ) 82.3 db (89.5 db typ) 79.7 db (86.4 db typ) sensitivity, absolute C110.5 db (C114.5 dbm typ) C106.5 db (C111.5 dbm t yp) C101.5 db (C107.5 dbm typ) C98.5 db (C104.5 dbm typ) accuracy relative 0.08 db 0.16 db 0.16 db 0.23 db absolute, 20 to 30 c 0.62 db ( 0.20 db 95%) 0.88 db ( 0.23 db 95%) 1.05 db ( 0.31 db 95%) 1.53 db ( 0.64 db 95%) 4.36 mhz offset (rbw = 10 khz) dynamic range, relative 94.2 db (99.5 db typ) 88.1 db (94.4 db typ) 82.8 db (89.9 db typ) 80.4 db (87.7 db typ) sensitivity, absolute C110.5 db (C114.5 dbm typ) C106.5 db (C111.5 dbm t yp) C101.5 db (C107.5 dbm typ) C98.5 db (C104.5 dbm typ) accuracy relative 0.01 db 0.18 db 0.18 db 0.29 db absolute 0.62 db ( 0.20 db 95%) 0.88 db ( 0.23 db 95%) 1.05 db ( 0.31 db 95%) 1.53 db ( 0.64 db 95%) isdb-t modulation accuracy segments = 13, mode 3, gi = 1 /8, partial reception = off, layer a-c segment = 13, code rate = 3 /4, time interleaving i = 2, modualtion = 64qam ml 1 = ?20 dbm, 20 to 30 c evm operating range 0 to 8% 0 to 8% 0 to 8% 0 to 8% floor 0.36% (eq off) 0.66% (eq off) 0.80% (eq off) 0.99% (eq off) accuracy from 0.40/0.66/0.80% (pxa/mxa/exa) to 1.2% 0.20% 0.30% 0.40% from 1.2 to 2.0% 0.20% 0.20% 0.30% from 2.0 to 8.0% 0.70% 0.70% 0.70% mer operating range 22 db 22 db 22 db 22 db floor 49 db (eq off) 44 db (eq off) 42 db (eq off) 40.1 db (eq off) accuracy from 38 to 48 db (pxa/mxa/exa) 2.54 db 2.68 db 3.00 db from 34 to 38 db 0.67 db 1.16 db 1.52 db from 22 to 34 db 0.61 db 0.73 db 0.85 db frequency error2 range C100 to 100 khz C100 to 100 khz C100 to 100 khz C100 to 100 khz accuracy 10 hz + tfa3 10 hz + tfa3 10 hz + tfa3 10 hz + tfa3 quad error range C5 to 5 deg C5 to 5 deg C5 to 5 deg C5 to 5 deg amplitude imbalance range C1 to 1 db C1 to 1 db C1 to 1 db C1 to 1 db channel impulse response (sfn echo pattern) (a) selectable center and time/div (b) scale type by time or distance (c) results sorted by amplitude or time/distance (d) default echo search limit -35 db and adjustable (e) adjustable fft start position (0/8 to 8/8 gi), and mer metric displayed on the top of the view can be used as the criteria to tune the fft window (f) support pre-echo, post-echo, 0-db echo, and out-of-gi echo scenarios 1. ml (mixer level) is rf input power minus attenuation 2. the accuracy specifcation applies at the evm = 1% 3. tfa = transmitter frequency frequency reference accuracy
12 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview for a complete list of specifications refer to the appropriate specifications guide. pxa: www.keysight.com/find/pxa_specifications mxa: www.keysight.com/find/mxa_specifications exa: www.keysight.com/find/exa_specifications cxa: www.keysight.com/find/cxa_specifications description pxa mxa exa cxa isdb-tmm mod accuracy for isdb-tmm, segments = 33, mode 3, gi = 1/4, super segment #0 isdb-t, super segment #1 six one- segment, super segment #2 isdb-t, ml 1 = -23 dbm, 20 to 30 c, cf 1 ghz evm eq off eq off eq off eq off operating range 0 to 25% 0 to 25% 0 to 25% 0 to 25% floor 0.32% 0.51% 0.68% 0.99% mer eq off eq off eq off eq off operating range 12 db 12 db 12 db 12 db floor 50 db 46 db 44 db 40.1 db frequency error 2 range C170 khz to 170 khz C170 khz to 170 khz C170 khz to 170 khz C170 khz to 170 khz accuracy 1 hz + tfa 3 10 hz + tfa 3 10 hz + tfa 3 10 hz + tfa 3 clock error 2 accuracy C100 hz to 100 hz C100 hz to 100 hz C100 hz to 100 hz C100 hz to 100 hz range 1 hz + tfa 3 1 hz + tfa 3 1 hz + tfa 3 1 hz + tfa 3 quad error range C5 to 5 deg C5 to 5 deg C5 to 5 deg C5 to 5 deg amplitude imbalance range C1 to 1 db C1 to 1 db C1 to 1 db C1 to 1 db (nom) channel impulse response (sfn echo pattern) same as isdb-t channel impulse response 1. ml (mixer level) is rf input power minus attenuation 2. the accuracy specifcation applies at the evm = 1% 3. tfa = transmitter frequency frequency reference accuracy
13 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview ordering information the table below contains information on our fxed, perpetual licenses. for more information, please visit the product web pages. N6155A & w6155a isdb-t/tmm x-series measurement application description model-option additional information pxa, mxa, exa cxa isdb-t N6155A-2fp w6155a-2fp isdb-t/ tmm N6155A-3fp w6155a-3fp software licensing and confguration choose from two license types: C fied, perpetual license: this allows you to run the application in the x-series analyzer in which it is initially installed. C transportale, perpetual license: this allows you to run the application in the x-series analyzer in which it is initially installed, plus it may be transferred from one x-series analyzer to another. try before you buy! free 30-day trials of x-series measurement applications provide unrestricted use of each applica - tions features and functionality on your x-series analyzer. redeem a trial license online today: www.keysight.com/fnd/x-series_trial
14 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview hardware confgurations n9030a pxa signal analyzer description model-option additional information 3.6, 8.4, 13.6, 26.5, 43, 44 or 50 ghz frequency range n9030a-503, -508, -513, -526, -543, -544, or -550 one required analog baseband iq (bbiq) inputs n9030a-bba required for analog baseband measurement precision frequency reference n9030a-pfr recommended electronic attenuator, 3.6 ghz n9030a-ea3 recommended preamplifer, 3.6, 8.4, 13.6, 26.5, 42.98, 44, or 50 ghz n9030a-p03, -p08, -p13, -p26, -p43, -544, or -550 one recommended analysis bandwidth to 25, 40, or 160 mhz n9030a-b25, -b40, or -b1x one required for isdb-tmm wideband if output n9030a-cr3 optional programmable if output n9030a-crp optional n9020a mxa signal analyzer description model-option additional information 3.6, 8.4, 13.6, or 26.5 ghz frequency range n9020a-503, -508, -513, or -526 one required analog baseband iq (bbiq) inputs n9020a-bba required for analog baseband measurement precision frequency reference n9020a-pfr recommended electronic attenuator, 3.6 ghz n9020a-ea3 recommended preamplifer, 3.6, 8.4, 13.6, or 26.5 ghz n9020a-p03, -p08, -p13, or -p26 one recommended analysis bandwidth to 25 or 40 mhz n9020a-b25, -b40 one required for isdb-tmm wideband if output n9020a-cr3 optional programmable if output n9020a-crp optional n9010a exa signal analyzer description model-option additional information 3.6, 7.0, 13.6, or 26.5 ghz frequency range n9010a-503, -507, -513, or -526 one required precision frequency reference n9010a-pfr recommended electronic attenuator, 3.6 ghz n9010a-ea3 recommended preamplifer, 3.6 or 7.0 ghz n9010a-p03 or -p07 one recommended analysis bandwidth to 25 or 40 mhz n9010a-b25, -b40 one required for isdb-tmm wideband if output n9010a-cr3 optional programmable if output n9010a-crp optional n9000a cxa signal analyzer description model-option additional information 3.0, 7.5, 13.6, or 26.5 ghz frequency range n9000a-503, -507, -513, or -526 one required precision frequency reference n9000a-pfr recommended analysis bandwidth to 25 mhz n9000a-b25 required for isdb-tmm tracking generator, 9 khz to 3 ghz or 6 ghz n9000a-t03 or t06 one optional fine step attenuator n9000a-fsa recommended preamplifer, 3.0, 7.5, 13.6, or 26.5 ghz n9000a-p03, -p07, -p13, or -p26 one recommended analysis bandwidth to 25 mhz n9000a-b25 optional wideband if output n9000a-cr3 optional
15 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview related literature N6155A and w6155a isdb-t measurement application, demonstration guide, literature number 5990-5932en N6155A & w6155a isdb-t measurement application, measurement guide, part number n6155-90002 N6155A & w6155a isdb-t measurement application, user's and programmer's reference, part number n6155-90001 web product page: www.keysight.com/fnd/N6155A www.keysight.com/fnd/w6155a x-series measurement applications: www.keysight.com/fnd/x-series_apps x-series signal analyzers: www.keysight.com/fnd/x-series application pages: www.keysight.com/fnd/digitalvideo digital video solution table: www.keysight.com/fnd/digitalvideo_solution
16 | keysight | isdb-t/tmm x-series measurement application N6155A & w6155a - technical overview this information is subject to change without notice. ? keysight technologies, 2013 - 2015 published in usa, april 17, 2015 5990-4374en www.keysight.com mykeysight www.keysight.com/find/mykeysight a personalized view into the information most relevant to you. www.lxistandard.org lan extensions for instruments puts the power of ethernet and the web inside your test systems. keysight is a founding member of the lxi consortium. three-year warranty www.keysight.com/find/threeyearwarranty keysights commitment to superior product quality and lower total cost of ownership. the only test and measurement company with three-year warranty standard on all instruments, worldwide. keysight assurance plans www.keysight.com/find/assuranceplans up to five years of protection and no budgetary surprises to ensure your instruments are operating to specification so you can rely on accurate measurements. www.keysight.com/go/quality keysight technologies, inc. dekra certified iso 9001:2008 quality management system keysight channel partners www.keysight.com/find/channelpartners get the best of both worlds: keysights measurement expertise and product breadth, combined with channel partner convenience. for more information on keysight technologies products, applications or services, please contact your local keysight office. the complete list is available at: www.keysight.com/find/contactus americas canada (877) 894 4414 brazil 55 11 3351 7010 mexico 001 800 254 2440 united states (800) 829 4444 asia pacifc australia 1 800 629 485 china 800 810 0189 hong kong 800 938 693 india 1 800 11 2626 japan 0120 (421) 345 korea 080 769 0800 malaysia 1 800 888 848 singapore 1 800 375 8100 taiwan 0800 047 866 other ap countries (65) 6375 8100 europe & middle east austria 0800 001122 belgium 0800 58580 finland 0800 523252 france 0805 980333 germany 0800 6270999 ireland 1800 832700 israel 1 809 343051 italy 800 599100 luxembourg +32 800 58580 netherlands 0800 0233200 russia 8800 5009286 spain 800 000154 sweden 0200 882255 switzerland 0800 805353 opt. 1 (de) opt. 2 (fr) opt. 3 (it) united kingdom 0800 0260637 for other unlisted countries: www.keysight.com/find/contactus (bp-02-20-15)

▲Up To Search▲

Price & Availability of N6155A

	To Download N6155A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .