quantafob remote control system ds quantafob-1 applications ? general purpose remote switching ? electric gates ? roller shutter doors ? garden lighting. features ? up to 150m range ? 433mhz fm technology ? 1 C 4 channels each 1000w ? 12-30vac/dc or 230vac versions ? waterproof receiver (ip68) ? new high security rf protocol ? 4 changeover relays 5a @ 230vac ? outputs momentary or latching ? any switch map to any relay ? systems supplied ready to go ? fcc certi?ed and ce compliant description a highly versatile general purpose remote control system for many different applications. housed in a rugged ip68 weatherproof enclosure, the new quantafob system is ideally suited to any remote switch requirement. each receiver has 4 relays, using the easy-learn process each relay can be controlled from any switch on any transmitte r. additional transmitters may be added to the system using the same easy-learn process. installation is by screw terminals to the power supply and the output relay contacts. the output relays are activated by the button press on the trans mitter encoder.
quantafob ds - quantafob - 1 systems part numbers additional transmitters part number part number part number part number description description description description power supply power supply power supply power supply frequency frequency frequency frequency quantafob-4s1 1 ch system 12-30vac/dc 433 quantafob-4s2 2 ch system 12-30vac/dc 433 quantafob-4s3 3 ch system 12-30vac/dc 433 quantafob-4s4 4 ch system 12-30vac/dc 433 custom systems fobbers can be customised with logo, colour or com plete custom plastic housing for unique branding please contact sales for further info. ** range stated is optimum, direct line of sight. in worst conditions this can be reduced by over 50% part number part number part number part number description description description description range* range* range* range* frequency frequency frequency frequency FOBBER-4T1 1 sw 150m 433 fobber-4t2 2 sw 150m 433 fobber-4t3 3sw 150m 433 fobber-4t4 4 sw 150m 433 fobber-4t6 6 sw 150m 433 fobber-4t8 8 sw 150m 433
quantafob ds - quantafob - 1 relay outputs the receiver provides 4 changeover relay switches e ach capable of switching up to 1.2kw (5a @ 230v). e ach relay is independent and separately controlled, and can ther efore be used to switch most voltages either ac or dc. each output relay provides an isolated switch. conn ections are common (com), normally open (no) and no rmally closed (nc). installation below is a simple example showing one possible way to wire a relay in order to provide switched power to an external load: when the relay is energised the com connects to no and power is applied to the load. 1. open the enclosure by removing ?xing screws from the enclosure 2. remove the antenna and slide out the circuit boa rd. 3. connect the power supply screw terminals 12-32v ac or dc to the supply terminals. 4. wire your desired connections to the relay switc hes 5. once all required wiring is complete, use the ha ndheld quanta transmitter to switch the outputs on and off. 6. as supplied, the handheld will operate the outpu ts - button 1 to output 1, button 2 to output 2 etc . 7. change the output functions to latching, / momentar y operation.
quantafob ds - quantafob - 1 link positions relays lk1 lk2 rly 1 rly 2 rly 3 rly 4 fitted fitted 1/2 sec mom 1/2 sec mom 1/2 sec mom 1/2 sec mom fitted open mom mom latch latch open fitted mom mom mom mom open open latch latch latch latch con?guring receivers relays con?guring receivers relays con?guring receivers relays con?guring receivers relays receivers can be used for many applications. the li nk pins lk1 and lk2 set the action of the relays 1/2 sec mom = relay will operate for half a second no matter how long a transmitter switch is operate d mom = relay will operate for as long as transmitte r switch operated latch = relay will toggle on/off on each transmit ter button press
quantafob ds - quantafob - 1 with this system, you can pair together any individ ual transmitter button with any receiver relay output. without opening either e nclosure. all you need is a magnet. 1. brie?y (less than 1 second) place the transmitte r next to the receiver in the position shown and then remove it. 2. the receiver will buzz once once once once (one beep means the receiver unit is ready to allocate a transmitter to relay switch 1) 3. press the button on the transmitter which you w ish to pair 4. the receiver will beep twice to con?rm pairing 5. repeat for any additional transmitter switches note: each receiver has a maximum memory for up to 28 pa irings, these can be from any buttons on any transmitters! note: the switch that is operated by the magnet is on the left of the antenna. advanced note: it is possible to select relay outputs 2-4, by rep eating step 3 and counting the number of beeps. 2 beeps for rela y 2, 3 for 3 and 4 f or 4. advanced operation - pairing a transmitter button with a m agnet 1. hold the magnet in the position shown for ~5 sec onds. 2. the receiver will sound a long beep to con?rm erased advanced operation - erasing receiver memory with a mag net
quantafob ds - quantafob - 1 advanced operation - pairing a transmitter button using the internal learn switch to pair a new transmitter switch follow this procedure open the receiver enclosure and extract the circuitb oard assembly note!: any transmitter button can be con?gured to operate any of the receiver relays. 1. select the receiver output relay to learn to: 2. brie?y press the receiver pairing switch (s2) once 3. the learn led will ?ash once to indicate relay 1 is selected 4. after the led stops ?ashing, press the learn switc h again to select the next relay channel 5. repeat step 4 until the required relay is select ed. 6. press the button on the transmitter you want to learn to the chosen relay. 7. the learn led will ?ash to indicate pairing is compl ete. pairing a transmitter to a receiver the only limitation is that each receiver has a maximum memory for up to 30 pairings, these can be from the same or any number of transmitters. erasing receivers memory 1. press and hold the receiver learn switch for approx 10 seconds. 2. when the learn led turns on all memory is erased note : :: : you cannot erase individual tx encoders
quantafob ds - quantafob - 1 technical speci?cations transmitters: fobber transmitter transmitters: fobber transmitter transmitters: fobber transmitter transmitters: fobber transmitter enclosure rating: standard ip68 battery type: cr2032 (supplied) battery life: 2 years @ approx. 50 1/2second pres ses p/day dimensions: 90 x 54 x 27 mm changing the battery: changing the battery: changing the battery: changing the battery: remove the 2 enclosure screws . replace battery, taking care of contacts and the battery polarity receiver unit receiver unit receiver unit receiver unit enclosure rating: ip68 dimensions: 130 x 112 x 42 mm (not including anten na) operating temperature: -10 to +50 o celsius. *the relay contacts in this unit are for functional use only and must not be used for isolation purpos es electrical characteristics electrical characteristics electrical characteristics electrical characteristics min min min min typical typical typical typical max max max max units units units units supply voltage 2.9 3 3.3 v supply current 17 ma frequency: 433.92 mhz rf output power (erp) - 10 mw rf bandwidth 60 khz electrical characteristics electrical characteristics electrical characteristics electrical characteristics min min min min typical typical typical typical max max max max dimension dimension dimension dimension supply voltage for 11 32 vdc or ac relay rating* (230vac) rly1-4 5 12 a supply current : quiescent all relays operating* 25 140 ma time delay from tx on switch to rx relay operation 30 ms time delay from tx sw relax to rx relay release 30 ms
quantafob disclaimer: whilst the information in this document is believed to b e correct at the time of issue, rf solutions ltd does not accept any liability whatsoever for its accuracy, ade quacy or completeness. no express or implied warranty or representation is given relating to the information contained in this document. rf solutio ns ltd reserves the right to make changes and improvem ents to the product(s) described herein without notice. buyers and other users should determine for themselves the suitability of any such i nformation or products for their own particular require ments or speci?cation(s). rf solutions ltd shall not be liable for any loss or damage caused a s a result of users own determination of how to deploy or use r f solutions ltds products. use of rf solutions l td products or components in life support and/or safety applications is not authorised ex cept with express written approval. no licences are c reated, implicitly or otherwise, under any of rf soluti ons ltds intellectual property rights. liability for loss or damage resulting or caused by re liance on the information contained herein or from the us e of the product (including liability resulting from negligence or where rf solutions ltd was aware of the p ossibility of such loss or damage arising) is excluded. this will not operate to limit or restrict rf solutions ltds liability for death or personal injury resulting from its negligence. rf solutions ltd. recycling notice meets the following ec directives: do not discard with normal waste, please recycle. rohs directive 2002/95/ec speci?es certain limits for hazardous substances. weee directive 2002/96/ec waste electrical & electronic equipment. this product must be disposed of through a licensed weee collecti on point. rf solutions ltd., ful?lls its weee obligations by membership of an approved compliance s cheme. waste batteries and accumulators directive 2006/66/ec where batteries are ?tted, before recycling the product, the batteries must be removed and disposed of at a licensed collection point. environment agency producer registration number: wee/jb0104wv. mechanical dimensions red directive red directive red directive red directive this product meets the requirements of directive 20 14/53/eu. full declaration is available at:- https://www.rfsolutions.co.uk/certi?cation-i59
|
