lite-on dcc release lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto led displayproduct data sheetLTS-10803TBE spec no.: ds30-2013-0068effective date: 10/02/2013revision: a bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4
lite - on technology corpor ation property of lite - on only part no.: lts - 10803 tbe page: 1 of 8 bns - od - c131/a4 led display lt s - 10803tbe data sheet item description issuer date - rdr original spec. lucas 0 2 / 23 / 20 1 0 1 1.1 add liteon spec. i n page 3 1.2 add esd note in page 7 reo lin 07/11/2013 2 modify symbol location in page 3 reo lin 09/30/2013
lite - on technology corpor ation property of lite - on only part no.: lts - 10803 tbe page: 2 of 8 bns - od - c131/a4 features 1.0 inch ( 25.4 - mm) digit height. continuous uniform segments. low power requirement. excellent characters appearance. high brightness & high contrast. wide viewing angle. solid state reliability. categorized for luminou s intensity. lead - free package (according to rohs) description the lts - 10803 tbe is a 1.0 inch ( 25.40 mm) digit height single digit seven - segment display. this device utilizes blue led chips(ingan epi on a sapphire substrate) , and has a gray face and whi te segments. device part no. description ingan blue common a n ode lts - 10803 tbe
lite - on technology corpor ation property of lite - on only part no.: lts - 10803 tbe page: 3 of 8 bns - od - c131/a4 package dimensions notes: 1. all dimensions are in millimeters. tolerances are ? 0.25 mm (0.01) unless otherwise noted. 2. pin tips shift tolerance is ? 0.4 mm. 3. foreign material on segment Q 10mils 4. ink contamination (surface) Q 20mils 5. bending Q 1% of reflector length 6. bubble in segment Q 10mils 7. recommend t he best pcb hole : diameter 1. 0 mm
lite - on technology corpor ation property of lite - on only part no.: lts - 10803 tbe page: 4 of 8 bns - od - c131/a4 internal circuit diagram
lite - on technology corpor ation property of lite - on only part no.: lts - 10803 tbe page: 5 of 8 bns - od - c131/a4 pin connection no. connection 1 cathode a 2 cathode h 3 cathode f 4 common anode 5 cathode e 6 cathode d 7 cathode k 8 cathode c 9 cathode g1 10 cathode g2 11 cathode b
lite - on technology corpor ation property of lite - on only part no.: lts - 10803 tbe page: 6 of 8 bns - od - c131/a4 absolute maximum rating at ta=25 o c parameter maximum rating unit power dissipation per segment 140( 70 ) mw peak forward current per segment ( 1/10 duty cycle, 0.1ms pulse width ) 3 0 ma continuous forward current per segment derating linear from 25 per segment 25 0. 28 ma ma/ operating temperature range - 35 to + 10 5 storage temperature range - 35 to + 10 5 solder temperature: max 260 for max 3sec at 1.6mm[1/16inch] below seating plane. electrical / optical characteristics at ta=25 o c paramet er symbo l min. typ. max. unit test condition average luminous intensity i v 25168 ? cd i f =1 0 ma peak emission wavelength ? p 468 nm i f =20ma spectral line half - width ? ? 25 nm i f =20ma dominant wavelength ? d 470 nm i f =20ma forward voltage per segment v f 6.6( 3.3 ) 7.6(3.8) v i f =20ma reverse current per segment (2) i r 100 ? a v r =5v luminous intensity matching ratio i v - m 2:1 i f =1ma note: 1. luminous intensity is measured with a light sensor and filter combination that approximates the cie ( commision internationale de leclariage ) eye - response curve. 2. r everse voltage is only for ir test, it can not contin ue to operate this situation. 3. cross talk specification Q 2.5%
lite - on technology corpor ation property of lite - on only part no.: lts - 10803 tbe page: 7 of 8 bns - od - c131/a4 esd (electrostatic discharge) static electricity or power surge will damage the le d. suggestions to prevent esd damage: ? use of a conductive wrist band or anti - electrostatic glove when handling these leds. ? all devices, equipment, and machinery must be properly grounded. ? work tables, storage racks, etc. should be properly grounded. ? use i on blower to neutralize the static charge which might have built up on surface of the leds plastic for n/d as a result of friction between leds during storage and handling.
lite - on technology corpor ation property of lite - on only part no.: lts - 10803 tbe page: 8 of 8 bns - od - c131/a4 typical electrical / optical characteristic curves (25 o c ambient temperature unless otherwise noted)
|
