micro tilt sensor d6bn 1 micro tilt sensor d6bn surface mounting tilt sensor fits space- confined installations ? low profile 2mm detect tilting over a range of 40 to 80 degrees in right-and- left inclination gull wing surface mount terminals wide operating temperature range: -10 to 60c ideal for pdas, cell phones and test equipment; digital cam- eras and video cameras to change aspect ratio automati- cally; also replaces mercury switches in portable space heaters and gaming machines, such as pinball games, and slot machines rohs compliant ordering information specifications absolute maximum ratings electrical characteristics note: measured under standard conditions of ambient temperature 5c to 35c. performance refer to the drawing on the following page for an operational diagram showing operation and return angles. operation angle return angle output rating operating voltage model 40 t o 80 50 t o 10 0.4 vdc 2.4 to 3.6 vdc D6BN-1P supply voltage range (v dd ) -0.1 to 5.0 vdc output current (i out ) 1 ma operating temperature range -10 to 60c with no icing storage temperature range -25 to 70c operating/storage humidity range 25% to 85% rh with no icing or condensation power supply voltage range 2.4 to 3.6 vdc output high voltage v dd ? 0.4 v min. output low voltage 0.4 v max. current consumption 10 a max.; 10 a typical (v dd = 3) operation angle 40 to 80 (when output goes from high to low) return angle 50 to 10 (when output goes from low to high) vibration resistance malfunction: 10-55-10 hz 1.5 mm single amplitude (3.0 mm double amplitude) for 2 hours, 3-axis shock resistance malfunction: 735 m/s 2 (approx. 75g) electrical life expectancy 100,000 operations min. (15-20 operations/minute)
2 micro tilt sensor d6bn operation note: 1. operation angle: output goes from high to low. 2. return angle: output goes from low to high. 3. characteristic values are provided on condition that there is no tilt back and forth while the operation speed is 10 per second. installation terminal arrangement solder conditions in the case of sn-pb eutectic solder in the case of pb-free solder reflow times: 2 times max. desoldering conditions with blower employed desolder the sensor at a temperature of 240c within five seconds. if a soldering iron is applied manually, desolder the sensor within 10 seconds at an iron tip temperature of 260c or within three seconds at an iron tip temperature of 350c. high high low high low operation returning gravity direction horizontal condition returning operation high right and left inclination the horizontal state vcc or vref of system gnd of system front view i/o port(1) i/o port(2) or a /d transform micro computer temperature [c] time[s] preheat area 140 9030 reflow area 2305 20 peak temperature max. 240 5 temperature [c] time[s] preheat area 160 ~ 180 9030 reflow area 2305 40 peak temperature max. 250 10
micro tilt sensor d6bn 3 dimensions precautions the sensor does not use any materials detrimental to the ozone layer. specifications other than the electrical or mechanical characteris- tics, external dimensions, or mounting dimensions of the sensor are subject to change without notice. handling precautions operating environment the sensor consists of a hall ic and a magnet. check that the sensor in operation will not be influenced by any external magnetic fields. do not install any magnetic materials within 2 mm of the sensor, else the performance characteristics of the sensor may not be guaranteeable. if there are any objects (e.g. motors and solenoids) generating magnetic fields near the sensor, operate and test the sensor before the sensor comes into actual use. do not apply any voltage exceeding 5v to the sensor, else the ic may be damaged. do not wash the sensor after the sensor is soldered. do not mount or dismount the sensor while power if flowing to the sensor. the sensor may generate error signals if impacted at a minimum acceleration of 294 m/s 2 . the sensor may generate error signals if a vibration at a minimum frequency of 15 hz and a minimum acceleration of 15m/s 2 is applied to the sensor. confirm that no static electricity at a maximum voltage of 5kv is applied to the pins, else the ic may be damaged. operating characteristics the present output may stay unchanged if the inclination of the sen- sor back and forth is 20 or more. under that condition, the output might not change even when the sensor is leaned left or right. gravity direction (ex.) max.20 q max.20 q even if right and left are leaned in the state upset in a front and a back, output may not change low mata from high from low to high.
4 micro tilt sensor d6bn tape packing reel dimensions note: 1. this packing conforms eiaj standard. 2. this packing packs up d6bn- 2,500 pieces. 3. expression of label as follows; type name lot no. name of a company the country of origin
5 micro tilt sensor d6bn omron electronic components, llc terms and conditions of sales 1. definitions : the words used herein are defined as follows. (a) terms: these terms and conditions (b) seller: omron electronic components llc and its subsidiaries (c) buyer: the buyer of products, including any end user in section iii through vi (d) products: products and/or services of seller (e) including: including without limitation 2. offer; acceptance: these terms are deemed part of all quotations, acknowledgments, invoices, purchase orders and other documents, whether electronic or in writing, relating to the sale of products by seller. seller hereby objects to any terms proposed in buyer's purchase order or other documents which are inconsistent with, or in addition to, these te r ms . 3. distributor : any distributor shall inform its customer of the contents after and including section iii of these terms. 1. prices; payment : all prices stated are current, subject to change without notice by seller. buyer agrees to pay the price in effect at time of shipment. payments for products received are due net 30 days unless otherwise stated in the invoice. buyer shall have no right to set off any amounts against the amount owing in respect of this invoice. 2. discounts : cash discounts, if any, will apply only on the net amount of invoices sent to buyer after deducting transportation charges, taxes and duties, and will be allowed only if (a) the invoice is paid according to seller's payment terms and (b) buyer has no past due amounts owing to seller. 3. interest : seller, at its option, may charge buyer 1.5% interest per month or the maximum legal rate, whichever is less, on any balance not paid within the stated terms. 4. orders : seller will accept no order less than 200 u.s. dollars net billing. 5. currencies : if the prices quoted herein are in a currency other than u.s. dollars, buyer shall make remittance to seller at the then current exchange rate most favorable to seller; provided that if remittance is not made when due, buyer will convert the amount to u.s. dollars at the then current exchange rate most favorable to seller available during the period between the due date and the date remittance is actually made. 6. governmental approvals : buyer shall be responsible for all costs involved in obtaining any government approvals regarding the importation or sale of the products. 7. taxes : all taxes, duties and other governmental charges (other than general real property and income taxes) , including any interest or penalties thereon, imposed directly or indirectly on seller or required to be collected directly or indirectly by seller for the manufacture, production, sale, delivery, importation, consumption or use of the products sold hereunder (including customs duties and sales, excise, use, turnover and license taxes) shall be charged to and remitted by buyer to seller. 8. financial : if the financial position of buyer at any time becomes unsatisfactory to seller, seller reserves the right to stop shipments or require satisfactory security or payment in advance. if buyer fails to make payment or otherwise comply with these terms or any related agreement, seller may (without liability and in addition to other remedies) cancel any unshipped portion of products sold hereunder and stop any products in transit until buyer pays all amounts, including amounts payable hereunder, whether or not then due, which are owing to it by buyer. buyer shall in any event remain liable for all unpaid accounts. 9. cancellation; etc: orders are not subject to rescheduling or cancellation unless buyer indemnifies seller fully against all costs or expenses arising in connection therewith. 10. force majeure : seller shall not be liable for any delay or failure in delivery resulting from causes beyond its control, including earthquakes, fires, floods, strikes or other labor disputes, shortage of labor or materials, accidents to machinery, acts of sabotage, riots, delay in or lack of transportation or the requirements of any government authority. 11. shipping; delivery: unless otherwise expressly agreed in writing by seller: (a) all sales and shipments of products shall be fob shipping point (unless otherwise stated in writing by seller) , at which point title to and all risk of loss of the products shall pass from seller to buyer, provided that seller shall retain a security interest in the products until the full purchase price is paid by buyer; (b) delivery and shipping dates are estimates only; and (c) seller will package products as it deems proper for protection against normal handling and extra charges apply to special conditions. 12. claims: any claim by buyer against seller for shortage or damage to the products occurring before delivery to the carrier must be presented in detail in writing to seller within 30 days of receipt of shipment. 1. suitability: it is the buyer?s sole respoinsibility to ensure that any omron product is fit and sufficient for use in a motorized vehicle application. buyer shall be solely responsible for determining appropriateness of the particular product with respect to the buyer?s application including (a) electrical or electronic components, (b) circuits, (c) system assemblies, (d) end product, (e) system, (f) materials or substances or (g) operating environment. buyer acknowledges that it alone has determined that the products will meet their requirements of the intended use in all cases. buyer must know and observe all prohibitions of use applicable to the product/s. 2. use with attention: the followings are some examples of applications for which particular attention must be given. this is not intended to be an exhaustive list of all possible use of any product, nor to imply that any use listed may be suitable for any product: (a) outdoor use, use involving potential chemical contamination or electrical interference. (b) use in consumer products or any use in significant quantities. (c) energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (d) systems, machines, and equipment that could present a risk to life or property. 3. prohibited use: never use the product for an application involving serious risk to life or property without ensuring that the system as a whole has been designed to address the risks, and that the product is properly rated and installed for the intended use within the overall equipment or system. 4. motorized vehicle application: use of any product/s for a motorized vehicle application must be expressly stated in the specification by seller. 5. programmable products: seller shall not be responsible for the buyer's programming of a programmable product. 1. warranty : seller's exclusive warranty is that the products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by seller (or such other period expressed in writing by seller). seller makes no warranty or representation, express or implied, about all other warranties, non-infringement, merchantability or fitness for a particular purpose of the products. 2. buyer remedy : seller's sole obligation hereunder shall be to replace (in the form originally shipped with buyer responsible for labor charges for removal or replacement thereof) the non-complying product or, at seller's election, to repay or credit buyer an amount equal to the purchase price of the product; provided that there shall be no liability for seller or its affiliates unless seller's analysis confirms that the products were handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. return of any products by buyer must be approved in writing by seller before shipment. 3. limitation on liability : seller and its affiliates shall not be liable for special, indirect, incidental or consequential damages, loss of profits or production or commercial loss in any way connected with the products, whether such claim is based in contract, warranty, negligence or strict liability. further, in no event shall liability of seller or its affilitates exceed the individual price of the product on which liability is asserted. 4. indemnities : buyer shall indemnify and hold harmless seller, its affiliates and its employees from and against all liabilities, losses, claims, costs and expenses ( including attorney's fees and expenses ) related to any claim, investigation, litigation or proceeding ( whether or not seller is a party ) which arises or is alleged to arise from buyer's acts or omissions under these terms or in any way with respect to the products. 1. intellectual property : the intellectual property embodied in the products is the exclusive property of seller and its affiliates and buyer shall not attempt to duplicate it in any way without the written permission of seller. buyer (at its own expense) shall indemnify and hold harmless seller and defend or settle any action brought against seller to the extent that it is based on a claim that any product made to buyer specifications infringed intellectual property rights of another party. 2. property; confidentiality : notwithstanding any charges to buyer for engineering or tooling, all engineering and tooling shall remain the exclusive property of seller. all information and materials supplied by seller to buyer relating to the products are confidential and proprietary, and buyer shall limit distribution thereof to its trusted employees and strictly prevent disclosure to any third party. 3. performance data : performance data is provided as a guide in determining suitability and does not constitute a warranty. it may represent the result of seller's test conditions, and the users must correlate it to actual application requirements. 4. change in specifications : product specifications and description may be changed at any time based on improvements or other reasons. it is seller?s practice to change part numbers when published ratings or features are changed, or when significant engineering changes are made. however, some specifications of the product may be changed without any notice. 5. errors and omissions : the information on seller?s website or in other documentation has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 6. export controls : buyer shall comply with all applicable laws, regulations and licenses regarding (a) export of the products or information provided by seller; (b) sale of products to forbidden or other proscribed persons or organizations; (c)disclosure to non-citizens of regulated technology or information. 1. waiver : no failure or delay by seller in exercising any right and no course of dealing between buyer and seller shall operate as a waiver of rights by seller. 2. assignment : buyer may not assign its rights hereunder without seller's written consent. 3. law : these terms are governed by illinois law (without regard to conflict of laws) . federal and state courts in illinois have exclusive jurisdiction for any dispute hereunder. 4. amendment : these terms constitute the entire agreement between buyer and seller relating to the products, and no provision may be changed or waived unless in writing signed by the parties. 5. severability : if any provision hereof is rendered ineffective or invalid, such provision shall not invalidate any other provision. i. general ii. sales iii. pre cautions iv. warranty and limitation v. information; etc. vi. miscellaneous
6 micro tilt sensor d6bn certain precautions on specifications and use 1. suitability for use . seller shall not be responsible for conformity with any stan- dards, codes or regulations which apply to the combination of the product in buyer's application or use of the product. at buyer's request, seller will pro- vide applicable third party certification documents identifying ratings and limi- tations of use which apply to the product. this information by itself is not sufficient for a complete determination of the suitability of the product in com- bination with the end product, machine, system, or other application or use. buyer shall be solely responsible for determining appropriateness of the par- ticular product with respect to buyer's application, product or system. buyer shall take application responsibility in all cases but the following is a non- exhaustive list of applications for which particular attention must be given: (i) outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this document. (ii) energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles, safety equipment, and installations subject to separate industry or government regulations. (iii) use in consumer products or any use in significant quantities. (iv) systems, machines and equipment that could present a risk to life or property. please know and observe all prohibitions of use applicable to this product. never use the product for an application involving serious risk to life or property without ensuring that the system as a whole has been designed to a ddress the risks, and that the omron product is properly rated and installed for the intended use within the overall equipment or system. 2. programmable products . seller shall not be responsible for the user's programming of a programmable product, or any consequence thereof. 3. performance data . performance data given in this publication is provided as a guide for the user in determining suitability and does not constitute a war- ranty. it may represent the result of seller's test conditions, and the users must correlate it to actual application requirements. actual performance is subject to seller's warranty and limitations of liability. 4. change in specifications . product specifications and accessories may be changed at any time based on improvements and other reasons. it is our prac- tice to change part numbers when published ratings or features are changed, or when significant construction changes are made. however, some specifica- tions of the product may be changed without any notice. when in doubt, spe- cial part numbers may be assigned to fix or establish key specifications for your application. please consult with your seller representative at any time to confirm actual specifications of purchased product. 5. errors and omissions . the information in this publication has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors, or omissions. 6. rohs compliance . where indicated, our products currently comply, to the best of our knowledge as of the date of this publication, with the requirements of the european union's directive on the restriction of certain hazardous substances ("rohs"), although the requirements of rohs do not take effect until july 2006. these requirements may be subject to change. please consult our website for current information. omron on-line global - http://www.omron.com usa - http://www.components.omron.com cat. no. j01c-e-01 printed in usa omron electronic components llc 55 e. commerce drive, suite b schaumburg, il 60173 847-882-2288 01/07 specifications subject to change without notice complete ?terms and conditions of sale? for product purchase and use are on omron?s website at http://www.components.omron.com ? under the ?about us? tab, in the legal matters section. all dimensions shown are in millimeters. to convert millimeters into inches, multiply by 0.03937. to convert grams into ounces, multiply by 0.03527.
|
