View MIC2876-50YMT-TR_8517005.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? 2016 microchip technology inc. ds20005572a-page 1 mic2876 features up to 95% efficiency input voltage range from 2.5v to 5.5v fully integrated, high-efficiency, 2 mhz synchronous boost regulator bi-directional true load disconnect integrated anti-ringing switch <1 a shutdown current bypass mode for v in v out overcurrent protection and thermal shutdown fixed and adjustable output versions 8-pin 2 mm 2 mm udfn package applications tablets and smartphones usb otg and hdmi hosts portable power reserve supplies high-current parallel lithium cell applications portable equipment general description the mic2876 is a compact and highly efficient 2 mhz synchronous boost regulator with a 4.8a switch. it features a bi-directional load disconnect function that prevents any leakage current between the input and output when the device is disabled. the mic2876 operates in bypass mode automatically when the input voltage is greater than the ta rget output voltage. at light loads, the boost converter goes to the pfm mode to improve the efficiency. the mic2876 also features an integrated anti-ringing switch to minimize emi. the mic2876 is available in a 8-pin 2 mm 2 mm udfn package, with a junction temperature range of C40c to +125c. package types mic2876 (f ixed o utput ) 8-pin 2x2 udfn* (mt) (top view) mic2876 (a dj . o utput ) 8-pin 2x2 udfn* (mt) (top view) sw pgnd in agnd out/pg en outs x ep 12 3 45 6 7 8 sw pgnd in agnd out/pg en fb x ep 12 3 45 6 7 8 * includes exposed thermal pad (ep), see ta b l e 3 - 1 . 4.8a i sw , synchronous boost regulator with bi-directional load disconnect downloaded from: http:///
mic2876 ds20005572a-page 2 ? 2016 microchip technology inc. typical application schematics functional block diagrams mic2876 (fixed output) 2x2 udfn mic2876 (adj. output) 2x2 udfn agnd sw v in in en pgnd out /pg outs v out 2.5v to 5.0v c14.7f 10v l1 1h r1 0 v in c2*22f 10v 5.0v agnd sw v in in en pgnd out /pg fb v out 2.5v to 5.0v c14.7f 10v l1 1h r1 0 v in c2*22f 10v 5.0v r2n r3 n * two more 22 f capacitors should be added in parallel with c2 for v in > 5.0v. efficiency vs. load current en in sw anti- ringing reference generator 2mhz oscillator oc 4.8a pwm logic control current sense + slope compensation vin out body driver hs driver ls driver /pg pgnd agnd vref soft- start pwm outs vin en in sw anti- ringing reference generator 2mhz oscillator oc 4.8a pwm logic control current sense + slope compensation vin out body driver hs driver ls driver pgl pgh /pg fb pgnd agnd vref soft- start pwm mic2876 (fixed output) mic2876 (adj. output) downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 3 mic2876 1.0 electrical characteristics absolute maximum ratings ? in, en, out, fb, /pg to pgnd ................................................................................................... ................ C0.3v to +6v agnd to pgnd ................................................................................................................... ..................... C0.3v to +0.3v esd rating (hbm) ( note 1 ) .............................................................................................................................. ...... 1.5 kv esd rating (mm) ( note 1 ) .............................................................................................................................. ..........200v power dissipation ( note 2 ) .................................................................................................................... internally limited operating ratings ? supply voltage (v in ) .............................................................................................................................. ... +2.5v to +5.5v output voltage (v out ) .............................................................................................................................. ..... up to +5.5v enable voltage (v en ) .............................................................................................................................. ............0v to v in ? notice: stresses above those listed under absolute maximu m ratings may cause permanent damage to the device. this is a stress rating only and functiona l operation of the device at those or an y other conditions above those indicated in the operational sections of this s pecification is not intended. exposure to maximum rating conditions for extended periods may affect device reliability. ? notice: the device is not guaranteed to function outside its operating ratings. note 1: devices are esd sensitive. handling precautio ns are recommended. human body model, 1.5 k ? in series with 100 pf. 2: the maximum allowable power dissipation of any t a (ambient temperature) is p d(max) = (t j(max) C t a ) / ja . exceeding the maximum allowable power dissipation will result in excessive die temperature, and the reg- ulator will go into thermal shutdown. downloaded from: http:///
mic2876 ds20005572a-page 4 ? 2016 microchip technology inc. table 1-1: electrical characteristics electrical characteristics: v in = 3.6v, v out = 5v, c in = 4.7 f, c out = 22 f, l = 1 h, t a = 25c, unless noted. bold values are valid for C40c t j +125c. ( note 1 ) . parameters sym. min. typ. max. units conditions power supply supply voltage range v in 2.5 5.5 v uvlo rising threshold v uvlor 2 . 3 2 2.49 v uvlo hysteresis v uvloh 2 0 0m v quiescent current i vin 109 a non-switching v in shutdown current i vinsd 1 3 a v en = 0v, v in = 5.5v, v out = 0v v out shutdown current i voutsd 2 5 a v en = 0v, v in = 0.3v, v out = 5.5v output voltage v out v in 5 . 5 v feedback voltage v fb 0.8865 0.9 0.9135 v adjustable version, i out = 0a voltage accuracy C1.5 +1.5 % fixed version, i out = 0a line regulation 0.3 %/v 2.5v < v in < 4.5v, i out = 500 ma load regulation 0.2 %/a i out = 200 ma to 1200 ma maximum duty cycle d max 9 2 % minimum duty cycle d min 6 . 5 % low-side switch current limit ( note 2 ) i ls 3.8 4.8 5.8 av in = 2.5v switch on-resistance pmos 79 m ? v in = 3.0v, i sw = 200 ma, v out = 5.0v nmos 82 v in = 3.0v, i sw = 200 ma, v out = 5.0v switch leakage current i sw 0 . 2 5 a v en = 0v, v in = 5.5v oscillator frequency f osc 1.6 2 2.4 mhz overtemperature shutdown threshold t sd 1 5 5 c overtemperature shutdown hysteresis 1 5 c soft-start soft-start time t ss 1 . 1m s v out = 5.0v en, /pg control pins en threshold voltage v en 1.5 v boost converter and chip logic on 0.4 boost converter and chip logic off en pin current 1.5 3 a v in = v en = 3.6v power good threshold (rising) v /pg-thr 0 . 9 x v out v note 1: specification for packaged product only. 2: guaranteed by design and characterization. downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 5 mic2876 power good threshold (falling) v /pg-thf 0.83 x v out v table 1-1: electrical characteristics (continued) electrical characteristics: v in = 3.6v, v out = 5v, c in = 4.7 f, c out = 22 f, l = 1 h, t a = 25c, unless noted. bold values are valid for C40c t j +125c. ( note 1 ) . parameters sym. min. ty p. max. units conditions note 1: specification for packaged product only. 2: guaranteed by design and characterization. downloaded from: http:///
mic2876 ds20005572a-page 6 ? 2016 microchip technology inc. temperature specifications parameters sym. min. typ. max. units conditions temperature ranges junction operating temperature t j C40 +125 c note 1 storage temperature range t s C65 +150 c lead temperature +260 c soldering, 10s package thermal resistances thermal resistance, udfn-22-8ld ? ja 9 0 c / w note 1: the maximum allowable power dissipation is a functi on of ambient temperature, the maximum allowable junction temperature and the thermal resistance from junction to air (i.e., t a , t j , ? ja ). exceeding the maximum allowable power dissipation will cause the de vice operating junction te mperature to exceed the maximum +125c rating. sustained junction temperat ures above +125c can impa ct the device reliability. downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 7 mic2876 2.0 typical performance curves figure 2-1: efficiency vs. load current. figure 2-2: output voltage vs. load current. figure 2-3: output voltage vs. input voltage. figure 2-4: oscillator frequency vs. temperature. figure 2-5: output shutdown current vs. temperature. figure 2-6: feedback voltage vs. temperature. note: the graphs and tables provided following this note ar e a statistical summary based on a limited number of samples and are provided for informational purposes only. the performance characteristics listed herein are not tested or guaranteed. in some graphs or t ables, the data presented may be outside the specified operating range (e.g., outside specified power suppl y range) and therefore outs ide the warranted range. downloaded from: http:///
mic2876 ds20005572a-page 8 ? 2016 microchip technology inc. figure 2-7: uvlo threshold vs. temperature. figure 2-8: enable threshold vs. temperature. figure 2-9: power good threshold vs. temperature. figure 2-10: load transient (0a to 1.2a). figure 2-11: load transient (1.2a to 0a). figure 2-12: line transient (2.5v to 3.5v). v in = 3.5v, v out = 5.0v l = 1h, i out = 0a to 1.2a time (100s/div) i out (1a/div) v sw (5v/div) v /pg (2v/div) v out (1v/div) (ac-coupled) time (100s/div) i out (1a/div) v sw (5v/div) v /pg (2v/div) v out (1v/div) (ac-coupled) v in = 3.5v, v out = 5.0v l = 1h, i out = 1.2a to 0a time (100s/div) i l (2a/div) v in (2v/div) v out (5v/div) v out (500mv/div) (ac-coupled) v in = 2.5v to 3.5v, v out = 5.0v l = 1h, i out = 1a downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 9 mic2876 figure 2-13: line transient (3.5v to 2.5v) . figure 2-14: line transient (2.5v to 5.5v) . figure 2-15: line transient (5.5v to 2.5v). figure 2-16: output ripple (pulse skipping mode) . figure 2-17: output ripple (pwm mode) . figure 2-18: soft-start (boost mode) . time (100s/div) i l (2a/div) v in (2v/div) v out (5v/div) v out (500mv/div) (ac-coupled) v in = 3.5v to 2.5v, v out = 5.0v l = 1h, i out = 1a time (100s/div) i l (5a/div) v in (2v/div) v out (5v/div) v out (2v/div) (ac-coupled) v in = 2.5v to 5.5v v out = 5.0v l = 1h i out = 1a time (100s/div) i l (5a/div) v in (2v/div) v out (5v/div) v out (2v/div) (ac-coupled) v in = 5.5v to 2.5v v out = 5.0v, l = 1h i out = 1a pulse skipping modev in = 3.5v, v out = 5.0v, i out = 50ma time (4s/div) i l (200ma/div) v sw (2v/div) v out (50mv/div) (ac-coupled) pwm modev in = 3.5v, v out = 5.0v, i out = 1.2a time (200ns/div) i l (1a/div) v sw (5v/div) v out (50mv/div) (ac-coupled) boost modev in = 3.5v v out = 5.0v i out = 500ma time (400s/div) i l (1a/div) v en (2v/div) v /pg (2v/div) v out (5v/div) downloaded from: http:///
mic2876 ds20005572a-page 10 ? 2016 microchip technology inc. figure 2-19: soft-start (bypass mode). figure 2-20: bypass mode. figure 2-21: bypass mode. bypass modev in = 5.5v v out = 5.0v i out = 500ma time (400s/div) i l (1a/div) v en (2v/div) v /pg (5v/div) v out (5v/div) time (1s/div) v in (1v/div) v out (1v/div) bypass mode C v in > 5.0v v out = v in i out = 0a v out = 5.0v v out = 5.0v time (1s/div) v in (1v/div) v out (1v/div) bypass mode C v in > 5.0v v out = v in i out = 500ma v out = 5.0v v out = 5.0v downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 11 mic2876 3.0 pin descriptions the descriptions of the pins are listed in table 3-1 . table 3-1: pin function table pin number fixed output pin number adj. output pin name description 1 1 sw boost converter switch node: connect the inductor between in and sw pins. 2 2 pgnd power ground: the power ground for the synchronous boost dc/dc converter power stage. 3 3 in supply input: connect at least 1 f ceramic capacitor between in and agnd pins. 4 4 agnd analog ground: the analog ground for the regulator control loop. 5 outs output voltage sense pin: for output voltage regulation in fixed voltage version. connect to the boost converter output. 5 fb feedback pin: for output voltage regulation in adjustable version. connect to the feedback resistor divider. 6 6 en boost converter enable: when this pin is driven low, the ic enters shutdown mode. the en pin has an internal 2.5 m ? pull-down resistor. the output is disabled when this pin is left floating. 7 7 /pg open drain power good output (active low): the /pg pin is high impedance when the output voltage is below the power good threshold and becomes low once the output is above the power good threshold. the /pg pin has a typical r ds(on) = 90 ? and requires a pull up resistor of 1 m ? . connect /pg pin to agnd when the /pg signal is not used. 8 8 out boost converter output. ep ep epad exposed heat sink pad. connect to agnd for best thermal performance. downloaded from: http:///
mic2876 ds20005572a-page 12 ? 2016 microchip technology inc. 4.0 functional description 4.1 input (in) the input supply provides power to the internal mosfets gate drivers and control circuitry for the boost regulator. the operating input voltage range is from 2.5v to 5.5v. a 1 f low-esr ceramic input capacitor should be connected from in to agnd as close to mic2876 as possible to ensure a clean supply voltage for the device. a minimum voltage rating of 10v is recommended for the input capacitor. 4.2 switch node (sw) the mic2876 has internal low-side and synchronous mosfet switches. the swit ch node (sw) between the internal mosfet switches connects directly to one end of the inductor and provides the current path during switching cycles. the other end of the inductor is connected to the input supply voltage. due to the high-speed switching on this pin, the switch node should be routed away from sensitive nodes wherever possible. 4.3 ground path (agnd) the ground path (agnd) is for the internal biasing and control circuitry. agnd should be connected to the pcb pad for the package exposed pad. the current loop of the analog ground should be separated from that of the power groun d (pgnd). agnd should be connected to pgnd at a single point. 4.4 power ground (pgnd) the power ground (pgnd) is the ground path for the high current in the boost switches. the current loop for the power ground should be as short as possible and separate from the agnd loop as applicable. 4.5 boost converter output (out) a low-esr ceramic capacitor of 22 f (for operation with v in 5.0v), or 66 f (for operation with v in > 5.0v) should be connected from v out and pgnd as close as possible to the mic2876. a minimum voltage rating of 10v is recommended for the output capacitor. 4.6 enable (en) enable pin of the mic2876. a logic high on this pin enables the mic2876. when this pin is driven low, the mic2876 enters the shutdown mode. when the en pin is left floating, it is pulled- down internally by a built-in 2.5 m ? resistor. 4.7 feedback/output voltage sense (fb/outs) feedback or output voltage sense pin for the boost converter. for the fixed voltage version, this pin should be connected to the out pin. for the adjustable version, connect a resistor divider to set the output voltage (see output voltage programming for more information). 4.8 power good output (/pg) the open-drain active-low power-good output (/pg) is low when the output voltage is above the power-good threshold. a pull-up resistor of 1 m ? is recommended. 4.9 exposed heat sink pad (ep) the exposed heat sink pad, or epad (ep), should be connected to agnd for best thermal performance. downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 13 mic2876 5.0 application information 5.1 general description the mic2876 is a 2 mhz, current-mode, pwm, synchronous boost converter with an operating input voltage range of 2.5v to 5.5v. at light load, the converter enters pulse-skipping mode to maintain high efficiency over a wide range of load current. the maximum peak current in the boost switch is limited to 4.8a (typical). 5.2 bi-directional output disconnect the power stage of the mic2876 consists of a nmos transistor as the main swit ch and a pmos transistor as the synchronous rectifier. a control circuit turns off the back gate diode of the pmos to isolate the output from the input supply when the chip is disabled (v en = 0v). an always on maximum supply selector switches the cathode of the backgate diode to either the in or the out (whichever of the two has the higher voltage). as a result, the output of the mic2876 is bi-directionally isolated from the input as long as the device is disabled. the maximum supply selector and hence the output disconnect function requires only 0.3v at the in pin to operate. 5.3 integrated anti-ringing switch the mic2876 includes an anti-ringing switch that eliminates the ringing on the sw node of a conventional boost converter operating in the discontinuous conduction mode (dcm). at the end of a switching cycle during dcm operation, both the nmos and pmos are turned off. the anti-ringing switch in the mic2876 clamps the sw pin voltage to in to dissipate the remaining energy stored in the inductor and the parasitic elements of the power switches. 5.4 automatic bypass mode the mic2876 automatically operates in bypass mode when the input voltage is higher than the target output voltage. in bypass mode, the nmos is turned off while the pmos is fully turned on to provide a very low impedance path from in to out. 5.5 soft-start the mic2876 integrates an internal soft-start circuit to limit the inrush current during start-up. when the device is enabled, the pmos is turned-on slowly to charge the output capacitor to a voltage close to the input voltage. then, the device begins boost switching cycles to gradually charge up the output voltage to the target v out . 5.6 output voltage programming the mic2876 has an adjustable version that allows the output voltage to be set by an external resistor divider r2 and r3. the typical feedback voltage is 900 mv, the recommended maximum and mi nimum output voltage is 5.5v and 3.2v, respectively. the current through the resistor divider should be significantly larger than the current into the fb pin (typically 0.01 a). it is recommended that 0.1% tole rance feedback resistors must be used and the total resistance of r2 + r3 should be around 1 m ? . the appropriate r2 and r3 values for the desired output voltage are calculated as in equation 5-1 : equation 5-1: example 1: with a v out of 3.3v and an r3 value of 281.2 k ? (standard value is 280 k ? ), r2 calculates out to 750 k ? . example 2: with a v out of 5v and an r3 value of 200 k ? , r2 calculates out to 911.1 k ? (standard value is 910 k ? ). 5.7 current limit protection the mic2876 has a current limit feature to protect the part against heavy load conditions. when the current limit comparator determines that the nmos switch has a peak current higher than 4. 8a, the nmos is turned off and the pmos is turned on until the next switching cycle. the current limit protection is reset cycle by cycle. r 2 r 3 v out 0.9 v ------------- 1 C ?? ?? ? = downloaded from: http:///
mic2876 ds20005572a-page 14 ? 2016 microchip technology inc. 6.0 component selection 6.1 inductor inductor selection is a trade-off between efficiency, stability, cost, size, and rated current. because the boost converter is compensated internally, the recommended inductance is limited from 1 h to 2.2 h to ensure system st ability and presents a good balance between these considerations. a large inductance value reduces the peak-to-peak inductor ripple current hence the output ripple voltage. this also reduces both t he dc loss and the transition loss at the same inductors dc resistance (dcr). however, the dcr of an inductor usually increases with the inductance in the same package size. this is due to the longer windings required for an increase in inductance. since the majority of the input current passes through the inductor, the higher the dcr the lower the efficiency is, and more significantly at higher load currents. on the other hand, inductor with smaller dcr but the same inductance usually has a larger size. the saturation current rating of the selected inductor must be higher than the maximum peak inductor current to be encountered and should be at least 20% to 30% higher than the average inductor current at maximum output current. 6.2 input capacitor to the device supply a ceramic capacitor of 1 f or larger with low esr is recommended to reduce the input voltage ripple to ensure a clean supply voltage for the device. the input capacitor should be placed as close as possible to the mic2876 in and agnd pins with short traces to ensure good noise performance. x5r or x7r type ceramic capacitors are recommended for better tolerance over temperature. the y5v and z5u type temperature rating ceramic capacitors are not recommended due to their large reduction in capacitance over temperature and increased resistance at high frequencies. the use of these reduces their ability to filter out high-frequency noise. the rated voltage of the input capacitor should be at least 20% higher than the maximum operating input voltage over the operating temperature range. 6.3 input capacitor to the power path a ceramic capacitor of a 4.7 f of larger with low esr is recommended to reduce the input voltage fluctuation at the voltage supply of the high-current power path. an input capacitor should be placed close to the v in supply to the power inductor and pgnd for good device performance at heavy load condition. x5r- or x7r-type ceramic capacitors are recommended for better tolerance over temperature. the y5v and z5u type temperature rating ceramic capacitors are not recommended due to their large reduction in capacitance over temperature and increased resistance at high frequencies. these reduce their ability to filter out high-frequency noise. the rated voltage of the input capacitor should be at least 20% higher than the maximum operating input voltage over the operating temperature range. 6.4 output capacitor output capacitor selection is also a trade-off between performance, size, and cost. increasing the output capacitor will lead to an improved transient response; however, the size and cost also increase. for operation with v in 5.0v, a minimum of 22 f output capacitor with esr less than 10 m ? is required. for operation with v in > 5.0v, a minimum of 66 f output capacitor with esr less than 10 m ? is required. x5r or x7r type ceramic capacitors are recommended for better tolerance over temperature. additional capacitors can be added to improve the transient response, and to reduce the ripple of the output when the mic2876 operates in and out of bypass mode. the y5v and z5u type ceramic capacitors are not recommended due to their wide variation in capacitance over temperature and increased resistance at high frequencies. the rated voltage of the output capacitor should be at least 20% higher than the maximum operating output voltage over the operating temperature range. 0805 size ceramic capacitor is recommended for smaller esl at output capacitor which contributes smaller voltage spike at the output voltage of high-frequency switching boost converter. downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 15 mic2876 7.0 power dissipation as with all power devices, the ultimate current rating of the output is limited by t he thermal properties of the device package and the pcb on which the device is mounted. there is a simple, ohms law-type relationship between thermal resistance, power dissipation, and temperature which are analogous to an electrical circuit (see figure 7-1 ): figure 7-1: series electrical resistance circuit. from this simple circuit we can calculate v x if we know i source , v z , and the resistor values, r xy and r yz using equation 7-1 : equation 7-1: thermal circuits can be considered using this same rule and can be drawn similarly by replacing current sources with power dissipati on (in watts), resistance with thermal resistance (in c/w) and voltage sources with temperature (in c). figure 7-2: series thermal resistance circuit. now replacing the variables in the equation for v x , we can find the junction temperature (t j ) from the power dissipation, ambient temperature and the known thermal resistance of the pcb ( ca ) and the package ( jc ). equation 7-2: as can be seen in the diagram, total thermal resistance ja = jc + ca . this can also be written as in equation 7-3 : equation 7-3: given that all of the power losses (minus the inductor losses) are effectively in the converter are dissipated within the mic2876 package, p diss can be calculated thusly: equation 7-4: linear mode equation 7-5: boost mode equation 7-6: duty cycle (boost) in the equations above, ? is the efficiency taken from the efficiency curves and dcr represents the inductor dcr. jc and ja are found in the temperature specifications section of the data sheet. where the real board area differs from 1 square, ca (the pcb thermal resistance), values for various pcb copper areas can be taken from figure 7-3 . v x i source r xy r yz + ?? v z + ? = t j p diss ? jc ? ca + ?? t a + ? = t j p diss ? ja ?? t a + ? = p diss p out 1 ? --- 1 C ?? ?? ? i out 2 C dcr ? = p diss p out 1 ? --- 1 C ?? ?? ? i out 1 d C ------------ - ?? ?? 2 C dcr ? = d v out v in C v out ---------------------------- + downloaded from: http:///
mic2876 ds20005572a-page 16 ? 2016 microchip technology inc. figure 7-3: determining pcb area for a given pcb thermal resistance. figure 7-3 shows the total area of a round or square pad, centered on the device. the solid trace represents the area of a square, single-sided, horizontal, solder masked, copper pc board trace heat sink, measured in square millimeters. no airflow is assumed. the dashed line shows the pc boards trace heat sink covered in black oil-based paint and with 1.3 m/sec (250 feet per minute) airflow. this approaches a best case pad heat sink. conservative design dictates using the solid trace data, which indicates that a maximum pad size of 5000 mm 2 is needed. this is a pad 71 mm 71 mm (2.8 inches per side). downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 17 mic2876 8.0 pcb layout guidelines pcb layout is critical to achieve reliable, stable and efficient performance. a ground plane is required to control emi and minimize the inductance in power, signal and return paths. the following guidelines should be followed to ensure proper operation of the device. please refer to the mic2876 evaluation board document for the recommended placement and layout of components. 8.1 integrated circuit (ic) place the ic close to the point-of-load. use fat traces to route the input and output power lines. analog grounds and power ground should be kept separate and connected at a single location at the pcb pad for exposed pad of the ic. place as many thermal vias as possible on the pcb pad for the exposed pad and connect it to the ground plane to ensure a good pcb thermal resistance. 8.2 in decoupling capacitor the in decoupling capacitor must be placed close to the in pin of the ic and preferably connected directly to the pin and not through any via. the capacitor must be located right at the ic. the in decoupling capacitor should be connected as close as possible to agnd. the in terminal is noise sensitive and the placement of capacitor is very critical. 8.3 v in power path bulk capacitor the v in power path bulk capacitor should be placed and connected close to the v in supply to the power inductor and the pgnd of the ic. use either x5r or x7r temperature rating ceramic capacitors. do not use y5v or z5u type ceramic capacitors. 8.4 inductor keep both the inductor connections to the switch node (sw) and input power line short and wide enough to handle the switching current. keep the areas of the switching current loops small to minimize the emi problem. do not route any digital lines underneath or close to the inductor. keep the switch node (sw) away from the noise sensitive pins. to minimize noise, place a ground plane underneath the inductor. 8.5 output capacitor use wide and short traces to connect the output capacitor as close as possible to the out and pgnd pins without going through via holes to minimize the switching current loop during the main switch off cycle and the switching noise. use either x5r or x7r temperature rating ceramic capacitors. do not use y5v or z5u type ceramic capacitors. downloaded from: http:///
mic2876 ds20005572a-page 18 ? 2016 microchip technology inc. 9.0 packaging information 9.1 package marking information xxx yww c 8-pin udfn 76a 604 c example legend: xx...x product code or cust omer-specific information y year code (last digit of calendar year) yy year code (last 2 digits of calendar year) ww week code (week of january 1 is week 01) nnn alphanumeric traceability code pb-free jedec ? designator for matte tin (sn) * this package is pb-free. the pb -free jedec designator ( ) can be found on the outer packaging for this package. , , pin one index is identified by a dot, delta up, or delta down (triangle mark). note : in the event the full microchip part numbe r cannot be marked on one line, it will be carried over to the next line, t hus limiting the number of available characters for customer-specific informa tion. package may or may not include the corporate logo. underbar (_) symbol may not be to scale. 3 e 3 e downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 19 mic2876 8-lead udfn 2 mm x 2 mm package outline and recommended land pattern note: for the most current package drawings, please see the microchip packaging specification located at http://www.microchip.com/packaging downloaded from: http:///
mic2876 ds20005572a-page 20 ? 2016 microchip technology inc. notes: downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 21 mic2876 appendix a: revision history revision a (july 2016) converted micrel docu ment mic2876 to micro- chip data sheet ds20005572a. minor text changes throughout. updated tdfn package information to microchip- standard udfn. downloaded from: http:///
mic2876 ds20005572a-page 22 ? 2016 microchip technology inc. notes: downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 23 mic2876 product identification system to order or obtain information, e.g., on pricing or delivery, contact your local microchip representative or sales office . examples: a) mic2876-4.75ymt-t5: mic2876, 4.75v output voltage, C40c to +125c temp. range, 8-pin udfn, 500/reel b) mic2876-4.75ymt-tr: mic2876, 4.75v output voltage, C40c to +125c temp. range, 8-pin udfn, 5,000/reel c) mic2876-5.0ymt-t5: mic2876, 5.00v output voltage, C40c to +125c temp. range, 8-pin udfn, 500/reel d) mic2876-5.0ymt-tr: mic2876, 5.00v output voltage, C40c to +125c temp. range, 8-pin udfn, 5,000/reel e) mic2876-5.25ymt-t5: mic2876, 5.25v output voltage, C40c to +125c temp. range, 8-pin udfn, 500/reel f) mic2876-5.25ymt-tr: mic2876, 5.25v output voltage, C40c to +125c temp. range, 8-pin udfn, 5,000/reel g) mic2876-5.5ymt-t5: mic2876, 5.50v output voltage, C40c to +125c temp. range, 8-pin udfn, 500/reel h) mic2876-5.5ymt-tr: mic2876, 5.50v output voltage, C40c to +125c temp. range, 8-pin udfn, 5,000/reel i) mic2876-aymt-t5: mic2876, adjustable output voltage, C40c to +125c temp. range, 8-pin udfn, 500/reel j) mic2876-aymt-tr: mic2876, adjustable output voltage, C40c to +125c temp. range, 8-pin udfn, 5,000/reel part no. x x package device device: mic2876: 4.8a i sw , synchronous boost regulator with bi-directional load disconnect output voltage: 4.75 = 4.75v 5.0 = 5.00v 5.25 = 5.25v 5.5 = 5.50v a = adjustable temperature: y = C40c to +125c package: mt = 8-pin 2 mm x 2 mm udfn media type: t5 = 500/reel tr = 5,000/reel xx output C voltage x temperature xx media C type downloaded from: http:///
mic2876 ds20005572a-page 24 ? 2016 microchip technology inc. notes: downloaded from: http:///
? 2016 microchip technology inc. ds20005572a-page 25 information contained in this publication regarding device applications and the like is prov ided only for your convenience and may be superseded by updates. it is your responsibility to ensure that your application me ets with your specifications. microchip makes no representations or warranties of any kind whether express or implied, written or oral, statutory or otherwise, related to the information, including but not limited to its condition, quality, performance, merchantability or fitness for purpose . microchip disclaims all liability arising from this information and its use. use of microchip devices in life support and/or safe ty applications is entirely at the buyers risk, and the buyer agrees to defend, indemnify and hold harmless microchip from any and all damages, claims, suits, or expenses resulting fr om such use. no licenses are conveyed, implicitly or ot herwise, under any microchip intellectual property rights unless otherwise stated. trademarks the microchip name and logo, the microchip logo, anyrate, dspic, flashflex, flexpwr, heldo, jukeblox, keeloq, keeloq logo, kleer, lancheck, link md, medialb, most, most logo, mplab, optolyzer, pic, picstart, pic32 logo, righttouch, spynic, sst, sst logo, superflash and uni/o are registered trademarks of microchip technology incorporated in the u.s.a. and other countries. clockworks, the embedded control solutions company, ethersynch, hyper speed control, hyperlight load, intellimos, mtouch, precision edge, and quiet-wire are registered trademarks of microc hip technology incorporated in the u.s.a. analog-for-the-digital age, any capacitor, anyin, anyout, bodycom, chipkit, chipkit logo, codeguard, dspicdem, dspicdem.net, dynamic average matching, dam, ecan, ethergreen, in-circuit serial programming, icsp, inter-chip connectivity, jitterblocker, kleernet, kleernet logo, miwi, motorbench, mpasm, mpf, mplab certified logo, mplib, mplink, multitrak, netdetach, omniscient code generation, picdem, picdem.net, pickit, pictail, puresilicon, righttouch logo, real ice, ripple blocker, serial quad i/o, sqi, superswitcher, superswitcher ii, total endurance, tsharc, usbcheck, varisense, viewspan, wiperlock, wireless dna, and zena are trademarks of microchip technology incorporated in the u.s.a. and other countries. sqtp is a service mark of mi crochip technology incorporated in the u.s.a. silicon storage technology is a registered trademark of microchip technology inc. in other countries. gestic is a registered tradem arks of microchip technology germany ii gmbh & co. kg, a subsidiary of microchip technology inc., in other countries. all other trademarks mentioned herein are property of their respective companies. ? 2016, microchip technology incorporated, printed in the u.s.a., all rights reserved. isbn: 978-1-5224-0760-7 note the following details of the code protection feature on microchip devices: microchip products meet the specification cont ained in their particular microchip data sheet. microchip believes that its family of products is one of the mo st secure families of its kind on the market today, when used i n the intended manner and under normal conditions. there are dishonest and possibly illegal meth ods used to breach the code protection fe ature. all of these methods, to our knowledge, require using the microchip products in a manner outside the operating specif ications contained in microchips data sheets. most likely, the person doing so is engaged in theft of intellectual property. microchip is willing to work with the customer who is concerned about the integrity of their code. neither microchip nor any other semiconduc tor manufacturer can guarantee the security of their code. code protection does not mean that we are guaranteeing the product as unbreakable. code protection is constantly evolving. we at microchip are committed to continuously improving the code protection features of our products. attempts to break microchips c ode protection feature may be a violation of the digital millennium copyright act. if such acts allow unauthorized access to your softwa re or other copyrighted work, you may have a right to sue for relief under that act. microchip received iso/ts-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in chandler and tempe, arizona; gresham, oregon and design centers in california and india. the companys quality system processes and procedures are for its pic ? mcus and dspic ? dscs, k ee l oq ? code hopping devices, serial eeproms, microper ipherals, nonvolatile memory and analog products. in addition, microchips quality system for the design and manufacture of development systems is iso 9001:2000 certified. quality management s ystem certified by dnv == iso/ts 16949 == downloaded from: http:///
ds20005572a-page 26 ? 2016 microchip technology inc. americas corporate office 2355 west chandler blvd. chandler, az 85224-6199 tel: 480-792-7200 fax: 480-792-7277 technical support: http://www.microchip.com/ support web address: www.microchip.com atlanta duluth, ga tel: 678-957-9614 fax: 678-957-1455 austin, tx tel: 512-257-3370 boston westborough, ma tel: 774-760-0087 fax: 774-760-0088 chicago itasca, il tel: 630-285-0071 fax: 630-285-0075 cleveland independence, oh tel: 216-447-0464 fax: 216-447-0643 dallas addison, tx tel: 972-818-7423 fax: 972-818-2924 detroit novi, mi tel: 248-848-4000 houston, tx tel: 281-894-5983 indianapolis noblesville, in tel: 317-773-8323 fax: 317-773-5453 los angeles mission viejo, ca tel: 949-462-9523 fax: 949-462-9608 new york, ny tel: 631-435-6000 san jose, ca tel: 408-735-9110 canada - toronto tel: 905-695-1980 fax: 905-695-2078 asia/pacific asia pacific office suites 3707-14, 37th floor tower 6, the gateway harbour city, kowloon hong kong tel: 852-2943-5100 fax: 852-2401-3431 australia - sydney tel: 61-2-9868-6733 fax: 61-2-9868-6755 china - beijing tel: 86-10-8569-7000 fax: 86-10-8528-2104 china - chengdu tel: 86-28-8665-5511 fax: 86-28-8665-7889 china - chongqing tel: 86-23-8980-9588 fax: 86-23-8980-9500 china - dongguan tel: 86-769-8702-9880 china - guangzhou tel: 86-20-8755-8029 china - hangzhou tel: 86-571-8792-8115 fax: 86-571-8792-8116 china - hong kong sar tel: 852-2943-5100 fax: 852-2401-3431 china - nanjing tel: 86-25-8473-2460 fax: 86-25-8473-2470 china - qingdao tel: 86-532-8502-7355 fax: 86-532-8502-7205 china - shanghai tel: 86-21-5407-5533 fax: 86-21-5407-5066 china - shenyang tel: 86-24-2334-2829 fax: 86-24-2334-2393 china - shenzhen tel: 86-755-8864-2200 fax: 86-755-8203-1760 china - wuhan tel: 86-27-5980-5300 fax: 86-27-5980-5118 china - xian tel: 86-29-8833-7252 fax: 86-29-8833-7256 asia/pacific china - xiamen tel: 86-592-2388138 fax: 86-592-2388130 china - zhuhai tel: 86-756-3210040 fax: 86-756-3210049 india - bangalore tel: 91-80-3090-4444 fax: 91-80-3090-4123 india - new delhi tel: 91-11-4160-8631 fax: 91-11-4160-8632 india - pune tel: 91-20-3019-1500 japan - osaka tel: 81-6-6152-7160 fax: 81-6-6152-9310 japan - tokyo tel: 81-3-6880- 3770 fax: 81-3-6880-3771 korea - daegu tel: 82-53-744-4301 fax: 82-53-744-4302 korea - seoul tel: 82-2-554-7200 fax: 82-2-558-5932 or 82-2-558-5934 malaysia - kuala lumpur tel: 60-3-6201-9857 fax: 60-3-6201-9859 malaysia - penang tel: 60-4-227-8870 fax: 60-4-227-4068 philippines - manila tel: 63-2-634-9065 fax: 63-2-634-9069 singapore tel: 65-6334-8870 fax: 65-6334-8850 taiwan - hsin chu tel: 886-3-5778-366 fax: 886-3-5770-955 taiwan - kaohsiung tel: 886-7-213-7828 taiwan - taipei tel: 886-2-2508-8600 fax: 886-2-2508-0102 thailand - bangkok tel: 66-2-694-1351 fax: 66-2-694-1350 europe austria - wels tel: 43-7242-2244-39 fax: 43-7242-2244-393 denmark - copenhagen tel: 45-4450-2828 fax: 45-4485-2829 france - paris tel: 33-1-69-53-63-20 fax: 33-1-69-30-90-79 germany - dusseldorf tel: 49-2129-3766400 germany - karlsruhe tel: 49-721-625370 germany - munich tel: 49-89-627-144-0 fax: 49-89-627-144-44 italy - milan tel: 39-0331-742611 fax: 39-0331-466781 italy - venice tel: 39-049-7625286 netherlands - drunen tel: 31-416-690399 fax: 31-416-690340 poland - warsaw tel: 48-22-3325737 spain - madrid tel: 34-91-708-08-90 fax: 34-91-708-08-91 sweden - stockholm tel: 46-8-5090-4654 uk - wokingham tel: 44-118-921-5800 fax: 44-118-921-5820 worldwide sales and service 06/23/16 downloaded from: http:///

▲Up To Search▲

Price & Availability of MIC2876-50YMT-TR

	To Download MIC2876-50YMT-TR Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .