View HV2601TFG-G_8466096.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? 2015-2016 microchip technology inc. ds20005391b-page 1 features high-voltage cmos technology for high perfor- mance 16-channel high voltage analog switch 3.3v input logic level compatible 20 mhz data shift clock frequency very low quiescent power dissipation (-10 a) low parasitic capacitance dc to 50 mhz small signal frequency response -60db typical off-isolation at 5.0 mhz cmos logic circuitry for low power excellent noise immunity cascadable serial data register with latches flexible operating supply voltages integrated bleed resistors on the outputs (hv2701 only) applications medical ultrasound imaging ndt metal flaw detection piezoelectric transducer drivers optical mems modules description hv2601/hv2701 are low-charge injection, 16-channel, high-voltage analog switch integrated circuits (ics). these devices are designed for use in applications requiring high-voltage switching controlled by low-volt- age control signals, such as medical ultrasound imag- ing and other piezoelectric transducer drivers. hv2701 has integrated bleed resistors which eliminate voltage build-up on capacitive loads such as piezoelectric transducers. these ics shift input data into a 16-bit shift register that can then be retained in a 16-bit latch. to reduce any possible clock feed-through noise, the latch enable bar should be left high until all bits are clocked in. data is clocked in during the rising edge of the clock. using high-voltage cmos technology, this device combines high-voltage, bilateral dmos switches and low power cmos logic to provide efficient control of high voltage analog signals. the device is suitable for various combinations of high voltage supplies, e.g., v pp /v nn : +40v/-160v, +100v/- 100v, and +160v/-40v. package types 42-ball bumped die see ta b l e 2 - 1 and ta b l e 2 - 2 for pin information 48-lead lqfp 1 2 3 8 9 10 12 13 4 5 6 7 11 18 17 16 15 14 25 26 21 22 23 24 19 20 41 42 33 34 39 40 31 32 37 38 29 30 35 36 27 28 1 48 (top view) (top view) hv2601 / hv2701 low-charge injection, 16-channel, high-voltage analog switch downloaded from: http:///
hv2601 / hv2701 ds20005391b-page 2 ? 2015-2016 microchip technology inc. block diagram dle clr latches level shifters output switches sw0 sw1 sw2 sw14 sw15 16-bit shift register rgnd vpp vnn clr le vdd gnd dle clr dle clr dle clr dle clr dout clk din bleed resistors hv2701 only note: bleed resistors and rgnd apply to hv2701 only. downloaded from: http:///
? 2015-2016 microchip technology inc. ds20005391b-page 3 hv2601 / hv2701 1.0 electrical characteristics absolute maximum ratings ? v dd logic supply ............ ...................................................................... ............ ........... .......... .....................-0.5v to +7.0v v pp - v nn differential supply............................................................................................................ ........................ 220v v pp positive supply ................................................................................................................ ......... -0.5v to v nn + 200v v nn negative supply................................................................................................................ .................+0.5v to -200v logic input voltage ............................................................................................................ ............... -0.5v to v dd + 0.3v analog signal range ......... ................................................................... ............ ........... ......... ........................... v nn to v pp peak analog signal current/channel ........................ ..................................................................... ............................ 3.0a storage temperature ............................................................................................................ ................. -65c to +150c power dissipation 42-ball bumped di e ........................................................................................... ........................ 1.5w power dissipation 48-lead lqfp ..... ............................................................................................ .......................... 1.0w note 1: power up/down sequence is arbitrary except gnd must be powered-up first and powered-down last. 2: v sig must be v nn and v pp or floating during power up/down transition. 3: rise and fall times of power supplies v dd , v pp , and v nn should not be less than 1.0msec. ? notice: stresses above those listed under maximum ratings may cause permanent damage to the device. this is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operational listings of this specification is not implied. exposure to maximum rating conditions for extended perio ds may affect devi ce reliability. recommended operating conditions ( notes 1 C 3 ) symbol parameter value v dd logic power supply voltage 3.0v to 5.5v v pp positive high voltage supply +40v to v nn +200v v nn negative high voltage supply -40v to -160v v ih high level input voltage 0.9v dd to v dd v il low level input voltage 0v to 0.1 v dd v sig analog signal voltage peak-to-peak v nn +10v to v pp -10v t a operating free air temperature 0c to 70c downloaded from: http:///
hv2601 / hv2701 ds20005391b-page 4 ? 2015-2016 microchip technology inc. dc electrical characteristics electrical specifications: over recommended operating co nditions unless otherwise noted. parameter symbol 0c 25c 70c units conditions min max min typ max min max small signal switch on-resistance r ons - 30 - 26 38 - 48 ? i sig = 5.0 ma v pp = +40v v nn = -160v - 25 - 22 27 - 32 i sig = 200 ma - 25 - 22 27 - 30 i sig = 5.0 ma v pp = +100v v nn = -100v - 18 - 18 24 - 27 i sig = 200 ma - 23 - 20 25 - 30 i sig = 5.0 ma v pp = +160v v nn = -40v - 22 - 16 25 - 27 i sig = 200 ma small signal switch on-resistance matching ? r ons -2 0-5 . 02 0-2 0% i sig = 5.0ma, v pp = +100v, v nn = -100v large signal switch on-resistance r onl ---1 5--- ? v sig = v pp -10v, i sig = 1.0a value of output bleed resistor (hv2701 only) r int - - 20 35 50 - - k ? output switch to r gnd i rint = 0.5 ma switch off leak- age per switch i sol -5 . 0-1 . 01 0 - 1 5 a v sig = v pp -10v and v nn +10v ( note 1 ) dc offset switch off v os - 300 - 100 300 - 300 mv hv2601:100 k ? load hv2701: no load ( note 1 ) dc offset switch on - 500 - 100 500 - 500 mv quiescent v pp supply current i ppq - - - 10 50 - - a all switches off quiescent v nn supply current i nnq - - - -10 -50 - - a all switches off quiescent v pp supply current i ppq - - - 10 50 - - a all switches on, i sw = 5.0 ma quiescent v nn supply current i nnq - - - -10 -50 - - a all switches on, i sw = 5.0 ma switch output peak current i sw - 3.0 - 3.0 2.0 - 2.0 a v sig duty cycle < 0.1% output switching frequency f sw ----5 0--k h z d u t y c y c l e = 5 0 % average v pp supply current i pp - 6.5 - - 7.0 - 8.0 ma v pp = +40v v nn = -160v all output switches are turning on and off at 50 khz with no load. v pp = +100v v nn = -100v - 4.0 - - 5.5 - 5.5 v pp = +160v v nn = -40v - 4.0 - - 5.0 - 5.5 average v nn supply current i nn - 6.5 - - 7.0 - 8.0 ma v pp = +40v v nn = -160v all output switches are turning on and off at 50 khz with no load. v pp = +100v v nn = -100v - 4.0 - - 5.0 - 5.5 v pp = +160v v nn = -40v - 4.0 - - 5.0 - 5.5 average v dd supply current i dd - 4.0 - - 4.0 - 4.0 ma f clk = 5.0 mhz, v dd = 5.0v downloaded from: http:///
? 2015-2016 microchip technology inc. ds20005391b-page 5 hv2601 / hv2701 note 1: see figure 3-1 . quiescent v dd supply current i ddq - 10 - - 10 - 10 a all logic inputs are static data out source current i sor 0.45 - 0.45 0.70 - 0.40 - ma v out = v dd - 0.7v data out sink current i sink 0.45 - 0.45 0.70 - 0.40 - ma v out = 0.7v logic input capacitance c in -1 0- -1 0-1 0p fC dc electrical characte ristics (continued) electrical specifications: over recommended operating co nditions unless otherwise noted. parameter symbol 0c 25c 70c units conditions min max min typ max min max downloaded from: http:///
hv2601 / hv2701 ds20005391b-page 6 ? 2015-2016 microchip technology inc. note 1: see figure 3-1 . ac electrical characteristics electrical specifications: v dd =5.0v, t r = t f 5.0 ns, 50% duty cycle, c load = 20 pf, unless otherwise noted. parameter symbol 0c 25c 70c units conditions min max min typ max min max set up time before le rises t sd 25 - 25 - - 25 - ns C time width of le t wle 56 - - 56 - 56 - ns v dd = 3.0v 12 - - 12 - 12 - v dd = 5.0v clock delay time to data out t do 50 100 50 78 100 50 100 ns v dd = 3.0v 15 40 15 30 40 15 40 v dd = 5.0v time width of clr t wclr 55 - 55 - - 55 - ns C set up time data to clock t su 21 - - 21 - 21 - ns v dd = 3.0v 7.0 - - 7.0 - 7.0 - v dd = 5.0v hold time data from clock t h 2.0 - 2.0 - - 2.0 - ns v dd = 3.0 or 5.0v clock frequency f clk - 8.0 - - 8.0 - 8.0 mhz v dd = 3.0v -2 0- -2 0-2 0 v dd = 5.0v clock rise and fall times t r ,t f -5 0- -5 0-5 0n sC turn on time t on - 5.0 - - 5.0 - 5.0 s v sig = v pp -10v, r load = 10k ? ( note 1 ) turn off time t off - 5.0 - - 5.0 - 5.0 s v sig = v pp -10v, r load = 10k ? ( note 1 ) maximum v sig slew rate dv/dt -2 0- -2 0-2 0 v/ns v pp = +40v, vnn= -160v -2 0- -2 0-2 0 v pp = +100v, vnn= -100v -2 0- -2 0-2 0 v pp = +160v, vnn= -40v off isolation k o -30 - -30 -33 - -30 - db f = 5.0mhz, 1.0k ? //15pf load ( note 1 ) -58 - -58 - - -58 - f = 5.0mhz, 50 ? load ( note 1 ) switch crosstalk k cr -60 - -60 -70 - -60 - db f = 5.0mhz, 50 ? load ( note 1 ) output switch iso- lation diode current i id - 300 - - 300 - 300 ma 300ns pulse width, 2.0% duty cycle ( note 1 ) off capacitance sw to gnd c sg(off) 5.0 17 5.0 12 17 5.0 17 pf 0v, f = 1.0mhz on capacitance sw to gnd c sg(on) 25 50 25 38 50 25 50 pf 0v, f = 1.0mhz output voltage spike +v spk ----1 5 0-- mv v pp = +40v, v nn = -160v, r load = 50 ? ( note 1 ) -v spk +v spk ----1 5 0-- v pp = +100v, v nn = -100v, r load = 50 ? ( note 1 ) -v spk +v spk ----1 5 0-- v pp = +160v, v nn = -40v, r load = 50 ? ( note 1 ) -v spk charge injection qc ---8 2 0--- pc v pp = +40v, v nn = -160v, v sig = 0v ( note 1 ) ---6 0 0--- v pp = +100v, v nn = -100v, v sig = 0v ( note 1 ) ---3 5 0--- v pp = +160v, v nn = -40v, v sig = 0v ( note 1 ) downloaded from: http:///
? 2015-2016 microchip technology inc. ds20005391b-page 7 hv2601 / hv2701 2.0 pin description the locations of the pads/balls are listed in package types . table 2-1: pin description: 42-ball bumped die package pin # hv2601 hv2701 description 1 nc rgnd no connect/ground for bleed resistor 2v pp v pp positive supply voltage 3v nn v nn negative supply voltage 4d out d out data out logic output 5 clr clr latch clear logic input 6 clk clk clock logic input for shift register 7 gnd gnd ground 8 sw15a sw15a analog switch 15 terminal a 9 sw15b sw15b analog switch 15 terminal b 10 le le latch-enable logic input, low active 11 v dd v dd logic supply voltage 12 sw0a sw0a analog switch 0 terminal a 13 sw0b sw0b analog switch 0 terminal b 14 sw14a sw14a analog switch 14 terminal a 15 sw14b sw14b analog switch 14 terminal b 16 d in d in data in logic input 17 sw1a sw1a analog switch 1 terminal a 18 sw1b sw1b analog switch 1 terminal b 19 sw13a sw13a analog switch 13 terminal a 20 sw13b sw13b analog switch 13 terminal b 21 sw2a sw2a analog switch 2 terminal a 22 sw2b sw2b analog switch 2 terminal b 23 sw12a sw12a analog switch 12 terminal a 24 sw12b sw12b analog switch 12 terminal b 25 sw3a sw3a analog switch 3 terminal a 26 sw3b sw3b analog switch 3 terminal b 27 sw11a sw11a analog switch 11 terminal a 28 sw11b sw11b analog switch 11 terminal b 29 sw9b sw9b analog switch 9 terminal b 30 sw8b sw8b analog switch 8 terminal b 31 sw7a sw7a analog switch 7 terminal a 32 sw6a sw6a analog switch 6 terminal a 33 sw4a sw4a analog switch 4 terminal a 34 sw4b sw4b analog switch 4 terminal b 35 sw10b sw10b analog switch 10 terminal b 36 sw10a sw10a analog switch 10 terminal a 37 sw9a sw9a analog switch 9 terminal a 38 sw8a sw8a analog switch 8 terminal a 39 sw7b sw7b analog switch 7 terminal b 40 sw6b sw6b analog switch 6 terminal b 41 sw5b sw5b analog switch 5 terminal b 42 sw5a sw5a analog switch 5 terminal a downloaded from: http:///
hv2601 / hv2701 ds20005391b-page 8 ? 2015-2016 microchip technology inc. table 2-2: pin description: 48-lead lqfp pin # hv2601 hv2701 description 1 nc nc no connect 2 nc nc no connect 3 sw4b sw4b analog switch 4 terminal b 4 sw4a sw4a analog switch 4 terminal a 5 sw3b sw3b analog switch 3 terminal b 6 sw3a sw3a analog switch 3 terminal a 7 sw2b sw2b analog switch 2 terminal b 8 sw2a sw2a analog switch 2 terminal a 9 sw1b sw1b analog switch 1 terminal b 10 sw1a sw1a analog switch 1 terminal a 11 sw0b sw0b analog switch 0 terminal b 12 sw0a sw0a analog switch 0 terminal a 13 v nn v nn negative supply voltage 14 nc nc no connect 15 v pp v pp positive supply voltage 16 nc nc no connect 17 gnd gnd ground 18 v dd v dd logic supply voltage 19 d in d in data in logic input 20 clk clk clock logic input for shift register 21 le le latch-enable logic input, low active 22 clr clr latch clear logic input 23 d out d out data out logic output 24 nc rgnd no connect/ground for bleed resistor 25 sw15b sw15b analog switch 15 terminal b 26 sw15a sw15a analog switch 15 terminal a 27 sw14b sw14b analog switch 14 terminal b 28 sw14a sw14a analog switch 14 terminal a 29 sw13b sw13b analog switch 13 terminal b 30 sw13a sw13a analog switch 13 terminal a 31 sw12b sw12b analog switch 12 terminal b 32 sw12a sw12a analog switch 12 terminal a 33 sw11b sw11b analog switch 11 terminal b 34 sw11a sw11a analog switch 11 terminal a 35 nc nc no connect 36 nc nc no connect 37 sw10b sw10b analog switch 10 terminal b 38 sw10a sw10a analog switch 10 terminal a 39 sw9b sw9b analog switch 9 terminal b 40 sw9a sw9a analog switch 9 terminal a 41 sw8b sw8b analog switch 8 terminal b 42 sw8a sw8a analog switch 8 terminal a 43 sw7b sw7b analog switch 7 terminal b downloaded from: http:///
? 2015-2016 microchip technology inc. ds20005391b-page 9 hv2601 / hv2701 44 sw7a sw7a analog switch 7 terminal a 45 sw6b sw6b analog switch 6 terminal b 46 sw6a sw6a analog switch 6 terminal a 47 sw5b sw5b analog switch 5 terminal b 48 sw5a sw5a analog switch 5 terminal a table 2-2: pin description: 48-lead lqfp pin # hv2601 hv2701 description downloaded from: http:///
hv2601 / hv2701 ds20005391b-page 10 ? 2015-2016 microchip technology inc. 3.0 detailed description 3.1 application information figure 3-1: test circuits rgnd rgnd rgnd rgnd rgnd rgnd rgnd dc offset switch on/off v pp 5v v nn vpp vnn vdd gnd v out t on /t off test circuit 5v gnd v pp -10v 10k v out output switch isolation diode current i id 5v gnd v nn v sig switch crosstalk v in = 10v p-p @5mhz nc 5v gnd 50 output voltage spike 5v gnd v out 1k r load 50 +v spk Cv spk off isolation k o = 20log v out v in v in = 10v p-p @5mhz 5v gnd v out 50 r load r load v pp v nn vpp vnn vdd v pp v nn vpp vnn vdd v pp v nn vpp vnn vdd v pp v nn vpp vnn vdd v pp v nn vpp vnn vdd k cr = 20log v out v in v pp -10v switch off leakage per switch rgnd open q = 1000pf x v out charge injection 5v gnd v pp v nn vpp vnn vdd v pp 5v v nn vpp vnn vdd open i sol gnd v out v out 1000pf v sig r load (hv2601 only) downloaded from: http:///
? 2015-2016 microchip technology inc. ds20005391b-page 11 hv2601 / hv2701 note 1: the 16 switches operate independently. 2: serial data is clocked in on t he l to h transition of the clk. 3: all 16 switches go to a state retaining thei r latched condition at the rising edge of le . when le is low the shift registers data flow through the latch. 4: d out is high when data in the shift register 15 is high. 5: shift registers clocking has no effect on the switch states if le is high. 6: the clr clear input overrides all other inputs. figure 3-2: logic timing waveforms table 3-1: logic function table d0 d1 ... d7 d8 ... d15 le clr sw0 sw1 ... sw7 sw8 ... sw15 l- ... -- ... -llo f f- ... -- ... - h- -- -llo n- -- - -l - - -ll-o f f - - - -h -- -ll-o n -- - - -- -- l l - -- -- - -- -- l l - -- -- -- l- -ll-- o f f- - -- h- -ll-- o n- - - - -l -ll- - -o f f - -- -h -ll-- -o n - - -- -- l l - -- -- - -- -- l l - -- -- - -- -- l l - -- -- - -- -- l l - -- -- -- -- lll-- -- o f f -- -- hll-- -- o n x x x x x x x h l hold previous state x x x x x x x x h all switches off data in din le clock clk data out dout off v out (typ) on clr 50% 50% 50% 50% t wle t sd t su t h 50% 50% t off 50% t do do t on t wcl d n+1 d n d n-1 50% 50% 90% 10% downloaded from: http:///
hv2601 / hv2701 ds20005391b-page 12 ? 2015-2016 microchip technology inc. 4.0 packaging information 4.1 package marking information legend: xx...x product code or cust omer-specific information y year code (last digit of calendar year) yy year code (last 2 digits of calendar year) ww week code (week of january 1 is week 01) nnn alphanumeric traceability code pb-free jedec ? designator for matte tin (sn) * this package is pb-free. the pb -free jedec designator ( ) can be found on the outer packaging for this package. note : in the event the full microchip part num ber cannot be marked on one line, it will be carried over to the next line, t hus limiting the number of available characters for product code or customer-specific information. package may or not include the corporate logo. 3 e 3 e 42-ball bumped die example xxxxx xxxxxxx yywwnnn e 1 bd hv2601 1550343 e 1 48-lead lqfp example nnn yyww xxxxxxx xxx e 3 343 1550 2601fg hv e 3 downloaded from: http:///
? 2015-2016 microchip technology inc. ds20005391b-page 13 hv2601 / hv2701 note: for more information about ball coordinates, contact microchip sales. 42-ball bumped die package outline (bd) 5.29x5.30mm bod, 1.0 mm height (max), 0.52 / 0.60mm pitch symbol a a1 a2 b d d1 e e1 e2 e e1 dimension (mm) min 0.9 0.21 0. 0.29 5.19 4.20 bsc 5.20 4.04 bsc 0.68 bsc 0.60 bsc 0.52 bsc nom 0.9 5 0.24 0.7 0.32 5.29 5.30 max 1.0 0.27 0.7 0.35 5.39 5.40 top view view b side view a2 a1 seatingplane view a view b bottom view d view a b e a note 1 (ball 1 index area d/4 x e/4) 0,0 e1 e1 e2 e d1 e e1 e1 e c/l c/l 1 42 1 42 notes: 1. %doolghqwl?hupxvwehorfdwhglqwkhlqgh[duhdlqglfdwhg%doolghqwl?hufdqehdproghgpdun lghqwl?hudqhpehgghgphwdopdunhurud printed indicator. 1rwhv )ruwkhprvwfxuuhqwsdfndjhgudzlqjv6hhwkh0lfurfkls3dfndjlqj6shflilfdwlrqdwzzzplfurfklsfr psdfndjlqj downloaded from: http:///
hv2601 / hv2701 ds20005391b-page 14 ? 2015-2016 microchip technology inc. 48-lead lqfp package outline (fg) 7.00x7.00mm bod, 1.60mm height (max), 0.50mm pitch symbol a a1 a2 b d d1 e e1 e l l1 l2 dimension (mm) min 1.40* 0.05 1.35 0.17 8.80* 6.80* 8.80* 6.80* 0.50 bsc 0.45 1.00 ref 0.25 bsc 0 o nom - - 1.40 0.22 9.00 7.00 9.00 7.00 0.60 3.5 o max 1.60 0.15 1.45 0.27 9.20* 7.20* 9.20* 7.20* 0.75 7 o jedec registration ms-026, variation bbc, isse d, jan. 2001. 7klvglphqvlrqlvqrwvshfl?hglqwkh-('(&gudzlqj drawings are not to scale. 1 seating plane gauge plane l l1 l2 view b view b seating plane top view side view note 1(index area d1/4 x e1/4) 48 a2 a a1 b d d1 e e1 e note: 1. $3lqlghqwl?hupxvwehorfdwhglqwkhlqgh[duhdlqglfdwhg7kh3lqlghqwl?hufdqehdproghg pdunlghqwl?hudqhpehggh gphwdopdunhuru a printed indicator. note: for the most current package drawings, see the microchip packaging specification at www.microchip.com/packaging. downloaded from: http:///
? 2015-2016 microchip technology inc. ds20005391b-page 15 hv2601 / hv2701 appendix a: revision history revision a (december 2015) converted supertex doc #s dsfp-hv2601 and dsfp-hv2701 to microchip ds20005391b. combined hv2601/hv2701 into one document. revised section 4.0 packaging information removed package ga from the data sheet. made minor text changes throughout. revision b (march 2016) moved block diagram to page 2 and made a minor change for clarity. removed confidential status from document. downloaded from: http:///
hv2601 / hv2701 ds20005391b-page 16 ? 2015-2016 microchip technology inc. product identification system to order or obtain information, e.g., on pricing or de livery, refer to the factory or the listed sales office . note: hv2601bd and hv2701bd are rohs-compliant products device: hv2601 = 16-channel hv analog switch hv2701 = 16-channel hv analog switch with bleed resistors package: bd = 42-ball bumped die fg = 48-lead lqfp environmental g = lead (pb)-free/rohs-compliant package (not used for bd packages) media type: (blank) = 250/tray for fg package m931 = 1000/reel for fg package m936 = 2500/reel for bd package examples: a) hv2601fg-g: 48-lead lqfp pack- age, 250/tray b) hv2601fg-g-m931: 48-lead lqfp pack- age, 1000/reel c) hv2701bd-m936 42-ball bumped die, 2500/reel part no. x device x environmental x x package media - - type downloaded from: http:///
? 2015-2016 microchip technology inc. ds20005391b-page 17 information contained in this publication regarding device applications and the like is prov ided only for your convenience and may be superseded by updates. it is your responsibility to ensure that your application me ets with your specifications. microchip makes no representations or warranties of any kind whether express or implied, written or oral, statutory or otherwise, related to the information, including but not limited to its condition, quality, performance, merchantability or fitness for purpose . microchip disclaims all liability arising from this information and its use. use of microchip devices in life support and/or safe ty applications is entirely at the buyers risk, and the buyer agrees to defend, indemnify and hold harmless microchip from any and all damages, claims, suits, or expenses resulting fr om such use. no licenses are conveyed, implicitly or ot herwise, under any microchip intellectual property rights unless otherwise stated. trademarks the microchip name and logo, the microchip logo, anyrate, dspic, flashflex, flexpwr, heldo, jukeblox, keeloq, keeloq logo, kleer, lancheck, link md, medialb, most, most logo, mplab, optolyzer, pic, picstart, pic32 logo, righttouch, spynic, sst, sst logo, superflash and uni/o are registered trademarks of microchip technology incorporated in the u.s.a. and other countries. clockworks, the embedded control solutions company, ethersynch, hyper speed control, hyperlight load, intellimos, mtouch, precision edge, and quiet-wire are registered trademarks of microc hip technology incorporated in the u.s.a. analog-for-the-digital age, any capacitor, anyin, anyout, bodycom, chipkit, chipkit logo, codeguard, dspicdem, dspicdem.net, dynamic average matching, dam, ecan, ethergreen, in-circuit serial programming, icsp, inter-chip connectivity, jitterblocker, kleernet, kleernet logo, miwi, motorbench, mpasm, mpf, mplab certified logo, mplib, mplink, multitrak, netdetach, omniscient code generation, picdem, picdem.net, pickit, pictail, puresilicon, righttouch logo, real ice, ripple blocker, serial quad i/o, sqi, superswitcher, superswitcher ii, total endurance, tsharc, usbcheck, varisense, viewspan, wiperlock, wireless dna, and zena are trademarks of microchip technology incorporated in the u.s.a. and other countries. sqtp is a service mark of mi crochip technology incorporated in the u.s.a. silicon storage technology is a registered trademark of microchip technology inc. in other countries. gestic is a registered tradem arks of microchip technology germany ii gmbh & co. kg, a subsidiary of microchip technology inc., in other countries. all other trademarks mentioned herein are property of their respective companies. ? 2015-2016, microchip technology incorporated, printed in the u.s.a., all rights reserved. isbn: 978-1-5224-0342-5 note the following details of the code protection feature on microchip devices: microchip products meet the specification cont ained in their particular microchip data sheet. microchip believes that its family of products is one of the mo st secure families of its kind on the market today, when used i n the intended manner and under normal conditions. there are dishonest and possibly illegal meth ods used to breach the code protection fe ature. all of these methods, to our knowledge, require using the microchip products in a manner outside the operating specif ications contained in microchips data sheets. most likely, the person doing so is engaged in theft of intellectual property. microchip is willing to work with the customer who is concerned about the integrity of their code. neither microchip nor any other semiconduc tor manufacturer can guarantee the security of their code. code protection does not mean that we are guaranteeing the product as unbreakable. code protection is constantly evolving. we at microchip are committed to continuously improving the code protection features of our products. attempts to break microchips c ode protection feature may be a violation of the digital millennium copyright act. if such acts allow unauthorized access to your softwa re or other copyrighted work, you may have a right to sue for relief under that act. microchip received iso/ts-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in chandler and tempe, arizona; gresham, oregon and design centers in california and india. the companys quality system processes and procedures are for its pic ? mcus and dspic ? dscs, k ee l oq ? code hopping devices, serial eeproms, microper ipherals, nonvolatile memory and analog products. in addition, microchips quality system for the design and manufacture of development systems is iso 9001:2000 certified. quality management s ystem certified by dnv == iso/ts 16949 == downloaded from: http:///
ds20005391b-page 18 ? 2015-2016 microchip technology inc. americas corporate office 2355 west chandler blvd. chandler, az 85224-6199 tel: 480-792-7200 fax: 480-792-7277 technical support: http://www.microchip.com/ support web address: www.microchip.com atlanta duluth, ga tel: 678-957-9614 fax: 678-957-1455 austin, tx tel: 512-257-3370 boston westborough, ma tel: 774-760-0087 fax: 774-760-0088 chicago itasca, il tel: 630-285-0071 fax: 630-285-0075 cleveland independence, oh tel: 216-447-0464 fax: 216-447-0643 dallas addison, tx tel: 972-818-7423 fax: 972-818-2924 detroit novi, mi tel: 248-848-4000 houston, tx tel: 281-894-5983 indianapolis noblesville, in tel: 317-773-8323 fax: 317-773-5453 los angeles mission viejo, ca tel: 949-462-9523 fax: 949-462-9608 new york, ny tel: 631-435-6000 san jose, ca tel: 408-735-9110 canada - toronto tel: 905-673-0699 fax: 905-673-6509 asia/pacific asia pacific office suites 3707-14, 37th floor tower 6, the gateway harbour city, kowloon hong kong tel: 852-2943-5100 fax: 852-2401-3431 australia - sydney tel: 61-2-9868-6733 fax: 61-2-9868-6755 china - beijing tel: 86-10-8569-7000 fax: 86-10-8528-2104 china - chengdu tel: 86-28-8665-5511 fax: 86-28-8665-7889 china - chongqing tel: 86-23-8980-9588 fax: 86-23-8980-9500 china - dongguan tel: 86-769-8702-9880 china - hangzhou tel: 86-571-8792-8115 fax: 86-571-8792-8116 china - hong kong sar tel: 852-2943-5100 fax: 852-2401-3431 china - nanjing tel: 86-25-8473-2460 fax: 86-25-8473-2470 china - qingdao tel: 86-532-8502-7355 fax: 86-532-8502-7205 china - shanghai tel: 86-21-5407-5533 fax: 86-21-5407-5066 china - shenyang tel: 86-24-2334-2829 fax: 86-24-2334-2393 china - shenzhen tel: 86-755-8864-2200 fax: 86-755-8203-1760 china - wuhan tel: 86-27-5980-5300 fax: 86-27-5980-5118 china - xian tel: 86-29-8833-7252 fax: 86-29-8833-7256 asia/pacific china - xiamen tel: 86-592-2388138 fax: 86-592-2388130 china - zhuhai tel: 86-756-3210040 fax: 86-756-3210049 india - bangalore tel: 91-80-3090-4444 fax: 91-80-3090-4123 india - new delhi tel: 91-11-4160-8631 fax: 91-11-4160-8632 india - pune tel: 91-20-3019-1500 japan - osaka tel: 81-6-6152-7160 fax: 81-6-6152-9310 japan - tokyo tel: 81-3-6880- 3770 fax: 81-3-6880-3771 korea - daegu tel: 82-53-744-4301 fax: 82-53-744-4302 korea - seoul tel: 82-2-554-7200 fax: 82-2-558-5932 or 82-2-558-5934 malaysia - kuala lumpur tel: 60-3-6201-9857 fax: 60-3-6201-9859 malaysia - penang tel: 60-4-227-8870 fax: 60-4-227-4068 philippines - manila tel: 63-2-634-9065 fax: 63-2-634-9069 singapore tel: 65-6334-8870 fax: 65-6334-8850 taiwan - hsin chu tel: 886-3-5778-366 fax: 886-3-5770-955 taiwan - kaohsiung tel: 886-7-213-7828 taiwan - taipei tel: 886-2-2508-8600 fax: 886-2-2508-0102 thailand - bangkok tel: 66-2-694-1351 fax: 66-2-694-1350 europe austria - wels tel: 43-7242-2244-39 fax: 43-7242-2244-393 denmark - copenhagen tel: 45-4450-2828 fax: 45-4485-2829 france - paris tel: 33-1-69-53-63-20 fax: 33-1-69-30-90-79 germany - dusseldorf tel: 49-2129-3766400 germany - karlsruhe tel: 49-721-625370 germany - munich tel: 49-89-627-144-0 fax: 49-89-627-144-44 italy - milan tel: 39-0331-742611 fax: 39-0331-466781 italy - venice tel: 39-049-7625286 netherlands - drunen tel: 31-416-690399 fax: 31-416-690340 poland - warsaw tel: 48-22-3325737 spain - madrid tel: 34-91-708-08-90 fax: 34-91-708-08-91 sweden - stockholm tel: 46-8-5090-4654 uk - wokingham tel: 44-118-921-5800 fax: 44-118-921-5820 worldwide sales and service 07/14/15 downloaded from: http:///

▲Up To Search▲

Price & Availability of HV2601TFG-G

	To Download HV2601TFG-G Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .