spec no: dsao4529 rev no: v.2b date: sep/25/2015 page: 1 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015152 2.0x1.25mm smd chip led lamp part number: APHBM2012LZGKSYKC green super bright yellow features 2.0mmx1.25mm smd led, 0.45mm max. thickness. bi -color, low power consumption. wide viewing angle. ideal for backlight and indicator. package : 2000pcs / reel. moisture sensitivity level : level 3. low current if=2ma operating. rohs compliant. descriptions the green source color devices are made with ingan on sapphire light emitting diode. the super bright yellow device is made with algainp (on gaas substrate) light emitting diode chip. electrostatic discharge and power surge could damage the leds. it is recommended to use a wrist band or anti- electrostatic gl ove when handling the leds. all devices, equipments and machineries must be electrically grounded. package dimensions notes: 1. all dimensions are in millimeters (inches). 2. tolerance is 0.1(0.004") unless otherwise noted. 3. the specifications, characteristics and technical data descri bed in the datasheet are subject to change without prior notice . 4. the device has a single mounting surface. the devi ce must be mounted according to the specifications. attention observe precautions for handling electrostatic discharge sensitive devices
spec no: dsao4529 rev no: v.2b date: sep/25/2015 page: 2 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015152 selection guide notes: 1. 1/2 is the angle from optical centerline where the lumi nous intensity is 1/2 of the optical peak value. 2. luminous intensity / luminous flux: +/-15%. 3. luminous intensity value is traceable to the cie127-2007 compliant national standards. absolute maximum ratings at ta=25c electrical / optical characteristics at ta=25c notes: 1.wavelength: +/-1nm. 2. forward voltage: +/-0.1v. 3. wavelength value is traceable to the cie127-2007 compliant national standards. 4.excess driving current and/or operating temperature higher t han recommended conditions may result in severe light degradation or premature failure. note: 1. 1/10 duty cycle, 0.1ms pulse width. part no. emitting color (material) lens type iv (mcd) [2] @ 2ma v iewing angle [1] min. typ. 2 1/2 APHBM2012LZGKSYKC green (ingan) water clear 50 90 super bright yellow (algainp) 6 10 120 symbol parameter emitting color typ. max. units test conditions peak peak wavelength green super bright yellow 515 590 nm i f =2ma d [1] dominant wavelength green super bright yellow 525 590 nm i f =2ma ? 1/2 spectral line half-width green super bright yellow 35 20 nm i f =2ma c capacitance green super bright yellow 45 20 pf v f =0v;f=1mhz v f [2] forward voltage green super bright yellow 2.65 1.85 3.1 2.1 v i f =2ma i r reverse current green super bright yellow 50 10 ua v r = 5v min. 2.2 1.5 parameter green super bright yellow units power dissipation 77.5 63 mw dc forward current 25 30 ma peak forward current [1] 150 175 ma reverse voltage 5 v operating temperature -40c to +85c storage temperature -40c to +85c electrostatic dischar ge threshold (hbm) 450 v 3000
spec no: dsao4529 rev no: v.2b date: sep/25/2015 page: 3 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015152 APHBM2012LZGKSYKC green
spec no: dsao4529 rev no: v.2b date: sep/25/2015 page: 4 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015152 super bright yellow
spec no: dsao4529 rev no: v.2b date: sep/25/2015 page: 5 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015152 APHBM2012LZGKSYKC reflow soldering is recommended and the soldering profile is shown below. other soldering methods are not recommended as they might cause damage to the product. recommended soldering pattern (units : mm; tolerance: 0.1) reel dimension tape dimensions (units : mm)
spec no: dsao4529 rev no: v.2b date: sep/25/2015 page: 6 of 6 approved: wynec checked: allen liu drawn: m.liu erp: 1203015152 packing & label specifications APHBM2012LZGKSYKC terms and conditions for the usage of this document 1. the information included in this docum ent reflects representative usage scenarios and is intended for technical reference on ly. 2. the part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. before production usage customer should refer to the latest datasheet for the updated specifications. 3. when using the products referenced in this document, please make sure the produc t is being operated within the environmental and electrical limits specified in the dat asheet. if customer usage exceeds the spec ified limits, kingbright will not be respon sible for any subsequent issues. 4. the information in this document applies to typical usage in consumer electronics applicati ons. if customer's application ha s special reliability requirements or have life-threatening liabilitie s, such as automotive or m edical usage, please consult with kingbright representative for further assistance. 5. the contents and information of this document may not be reproduced or re-transmitted without permission by kingbright. 6. all design applications should refer to kingbright application notes available at http://www.kingbrightusa.com/applicationnotes
|
