1. general description the 74hc4066-q100; 74hct4066-q100 is a quad single pole, single throw analog switch. each switch features two input/outpu t terminals (ny and nz) and an active high enable input (ne). when ne is low, the analog switch is turned off. inputs include clamp diodes. this enables the use of current limiting resistors to interface inputs to voltages in excess of v cc . this product has been qualified to the automotive electronics council (aec) standard q100 (grade 1) and is suitable for use in automotive applications. 2. features and benefits ? automotive product qualif ication in accordance with aec-q100 (grade 1) ? specified from ? 40 ? c to +85 ? c and from ? 40 ? c to +125 ? c ? input levels ne inputs: ? for 74hc4066-q100: cmos level ? for 74hct4066-q100: ttl level ? low on resistance: ? 50 ? (typical) at v cc = 4.5 v ? 45 ? (typical) at v cc = 6.0 v ? 35 ? (typical) at v cc = 9.0 v ? specified in compliance with jedec standard no. 7a ? esd protection: ? mil-std-883, method 3015 exceeds 2000 v ? hbm jesd22-a114f exceeds 2000 v ? mm jesd22-a115-a exceeds 200 v (c = 200 pf, r = 0 ? ) ? multiple package options 74hc4066-q100; 74hct4066-q100 quad single-pole singl e-throw analog switch rev. 3 ? 16 december 2013 product data sheet
74hc_hct4066_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved . product data sheet rev. 3 ? 16 december 2013 2 of 23 nxp semiconductors 74hc4066-q100; 74hct4066-q100 quad single-pole singl e-throw analog switch 3. ordering information 4. functional diagram table 1. ordering information type number package temperature range name description version 74hc4066d-q100 ? 40 ? c to +125 ? c so14 plastic small outline package; 14 leads; body width 3.9 mm sot108-1 74hct4066d-q100 74HC4066PW-Q100 ? 40 ? c to +125 ? c tssop14 plastic thin shrink small outline package; 14 leads; body width 4.4 mm sot402-1 74hct4066pw-q100 74hc4066bq-q100 ? 40 ? c to +125 ? c dhvqfn14 plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 14 terminals; body 2.5 ? 3 ? 0.85 mm sot762-1 74hct4066bq-q100 fig 1. logic symbol fig 2. iec logic symbol 001aad269 1y 1z 12 2y 2z 43 1e 13 3y 3z 89 4y 4z 11 10 3e 6 4e 12 2e 5 001aad270 12 13 # 43 5# 89 6# 11 10 (a) 12 # 12 13 1 x1 1 x1 1 x1 1 1 1 1 1 x1 # 43 5# 89 6# 11 10 (b) 12 # fig 3. schematic diagram (one switch) 001aad271 gnd nz ne ny v cc v cc
74hc_hct4066_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2013. all rights reserved . product data sheet rev. 3 ? 16 december 2013 3 of 23 nxp semiconductors 74hc4066-q100; 74hct4066-q100 quad single-pole singl e-throw analog switch 5. pinning information 5.1 pinning 5.2 pin description (1) this is not a supply pin. the substrate is attached to this pad using conductive die atta ch material. there is no electrical or mechanical requi rement to solder this pad. however, if it is soldered, the solder land should remain floating or be connected to vcc. fig 4. pin configuration for so14 and tssop14 fig 5. pin configuration for dhvqfn14 + & |