View LXA7-PW50_8285590.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

luxeon ? r freedom from binning luxeon r freedom from binning hot tested superior quality of light technical datasheet ds101 introduction luxeon ? r brings illumination grade led light sources to outdoor and industrial lighting applications and makes it easier than ever to design led solutions and bring them to market. with hot testing, every luxeon r is tested and specifed at real world operating conditions, t j =85c. freedom from binning means that every luxeon r led falls within a single 5 step macadam ellipse centered in ansi defned standard color spaces and now, luminaire manufacturers can be confdent in color consistency from led to led. the superior quality of light, volume of lumens, and real world effcacy enable leading performance and effcient solution development in a wide variety of lighting segments including streetlight, high bay, parking lot, low bay, industrial, under canopy, outdoor architectural, city beautifcation, and advertising/signage illumination luxeon r, ? freedom from binning for superior quality of light ? hot tested at real world conditions of 700 ma and t j = 85c ? maximum light output and lowest cost of light ? simplifed design and accelerated time to market ? specifed typical 75 cri and minimum 70 cri at 700 ma, t j = 85c.
luxeon r datasheet ds101 20130506 2 general product information .................................................................................................................................... 3 product nomenclature ..................................................................................................................................... 3 lumen maintenance ........................................................................................................................................... 3 environmental compliance .............................................................................................................................. 3 product selection ......................................................................................................................................................... 4 product selection guide for luxeon r emitters .................................................................................... 4 optical characteristics ............................................................................................................................................... 5 electrical characteristics ............................................................................................................................................ 6 absolute maximum ratings .............................................................................................................................. 7 jedec moisture sensitivity .............................................................................................................................. 7 refow soldering characteristics ............................................................................................................................. 8 mechanical dimensions .............................................................................................................................................. 9 pad confguration ........................................................................................................................................... 10 solder pad design ............................................................................................................................................ 10 typical light output characteristics over temperature ................................................................................... 11 typical forward current characteristics ............................................................................................................. 12 current derating curves ......................................................................................................................................... 13 typical radiation patterns ........................................................................................................................................ 15 emitter pocket tape packaging ................................................................................................................................ 16 emitter reel packaging ............................................................................................................................................. 17 product binning and labeling .................................................................................................................................. 18 luminous flux bins .................................................................................................................................................... 19 luxeon r 5-step macadam ellipse color defnition .......................................................................... 20 forward voltage bins ................................................................................................................................................. 21 table of contents
luxeon r datasheet ds101 20130506 3 product nomenclature luxeon r emitters are tested and binned hot under conditions comparable to those found in real-world lighting products. the test conditions for luxeon r are 700 ma d.c. with junction temperature at 85oc. the part number designation for the luxeon r emitters is explained as follows: l x a 7 - p w x x where: 7 designates minimum cri performance (value 7 = 70 minimum) p designates radiation pattern (value p for lambertian) w designates color (value w = white) xx designates nominal ansi cct (value 30 = 3000k, 40 = 4000k, 50 = 5000k, 57 = 5700k, and 65 = 6500k) lumen maintenance luxeon r products are tested in compliance with lm-80. please visit www.philipslumileds.com/support/documentation/lumen-maintenance or contact your local philips lumileds technical solutions manager for tm-21 extrapolations or other support. environmental compliance philips lumileds is committed to providing environmentally friendly products to the solid-state lighting market. luxeon r is compliant to the european union directives on the restriction of hazardous substances in electronic equipment, namely the rohs and reach directives. philips lumileds will not intentionally add the following restricted materials to the luxeon r: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (pbb) or polybrominated diphenyl ethers (pbde). general product information
luxeon r datasheet ds101 20130506 4 product selection guide for luxeon r emitters junction temperature = 85c table 1. typical performance characteristics at 350 ma, 700 ma, and 1000 ma for luxeon r, junction temperature = 85 c cri lum flux (lm) typ. lum flux (lm) typ. forward voltage (v f ) t yp. effcacy (lm/w) part nominal @ 700 ma min. @ @ @ @ @ @ @ @ @ @ number ansi cct min. typ. 700 ma 350 ma 700 ma 1000 ma 350 ma 700 ma 1000 ma 350 ma 700 ma 1000 ma lxa7-pw30 3000k 70 75 160 100 180 245 2.72 2.81 2.85 105 92 86 lxa7-pw40 4000k 70 75 200 119 215 292 2.72 2.81 2.85 125 109 103 LXA7-PW50 5000k 70 75 200 122 220 299 2.72 2.81 2.85 128 112 105 lxa7-pw57 5700k 70 75 200 122 220 299 2.72 2.81 2.85 128 112 105 lxa7-pw65 6500k 70 75 200 122 220 299 2.72 2.81 2.85 128 112 105 notes for table 1: 1. minimum luminous fux performance within published operating conditions. philips lumileds maintains a tolerance of 6.5% on luminous fux measurements. 2. philips lumileds maintains a tolerance of 0.06v on forward voltage measurements. product selection
luxeon r datasheet ds101 20130506 5 luxeon r at test current [1] junction temperature = 85c table 2. typical total typical color temperature included viewing cct angle [2] angle [3] nominal part (degrees) (degrees) ansi cct number typical u 0.90v 2 u 1/2 3000k lxa7-pw30 3045k 160 120 4000k lxa7-pw40 3985k 160 120 5000k LXA7-PW50 5028k 160 120 5700k lxa7-pw57 5665k 160 120 6500k lxa7-pw65 6530k 160 120 notes for table 2: 1. test current is 700 ma d.c. for all lxa7-pwxx emitters. 2. total angle at which 90% of total luminous fux is captured. 3. viewing angle is the off axis angle from lamp centerline where the luminous intensity is ? of the peak value. optical characteristics
luxeon r datasheet ds101 20130506 6 electrical characteristics at 700 ma for luxeon r junction temperature = 85oc table 3. typical temperature coeffcient of forward typical thermal resistance forward voltage v f [1] voltage [2] junction to nominal (v) (mv/c) thermal pad (c/w) ansi cct min. max. d v f / d t j r u j-c 3000k 2.5 3.25 -1.8 to -2.4 6 4000k 2.5 3.25 -1.8 to -2.4 6 5000k 2.5 3.25 -1.8 to -2.4 6 5700k 2.5 3.25 -1.8 to -2.4 6 6500k 2.5 3.25 -1.8 to -2.4 6 notes for table 3: 1. philips lumileds maintains a tolerance of 0.06v on forward voltage measurements. 2. measured between t j = 25c and t j = 110c at i f = 700 ma. electrical characteristics
luxeon r datasheet ds101 20130506 7 absolute maximum ratings table 4. parameter luxeon r dc forward current (ma) 1000 [2] peak pulsed forward current (ma) 1200 [3] esd sensitivity < 8000v human body model (hbm) class 3a jesd22-a114-e led junction temperature [1] 150c operating case temperature at 700 ma -40c - 135c storage temperature -40c - 135c soldering temperature jedec 020c 260c allowable refow cycles 3 reverse voltage (vr) luxeon r leds are not designed to be driven in reverse bias notes for table 4: 1. proper current derating must be observed to maintain junction temperature below the maximum. for additional information on thermal measurement guidelines please refer to application brief ab33. 2. residual periodic variations due to power conversion from alternating current (ac) to direct current (dc), also called ripple, with frequencies 100 hz and amplitude 200 ma are acceptable, assuming the average current throughout each cycle does not exceed 1000 ma. 3. pulsed operation with a peak drive current of 1200 ma is acceptable if the pulse on-time is 5 ms per cycle and the duty cycle is 50%. jedec moisture sensitivity table 5. soak requirements level floor life standard time conditions time conditions 1 unlimited 6 30c / 168h 85c / 85% 85% rh + 5 / -0 rh
luxeon r datasheet ds101 20130506 8 temperature profle for table 6. table 6. profle feature lead free assembly average ramp-up rate (ts max to t p ) 3c / second max preheat temperature min (ts min ) 150c preheat temperature max (ts max ) 200c preheat time (ts min to ts max ) 60 - 180 seconds temperature (t l ) 217c time maintained above temperature (t l ) 60 - 150 seconds peak / classifcation temperature (t p ) 260c time within 5c of actual peak temperature (t p ) 20 - 40 seconds ramp - down rate 6c / second max time 25c to peak temperature 8 minutes max notes for table 6: - all temperatures refer to the application printed circuit board (pcb), measured on the surface adjacent to the package body. refow soldering characteristics jedec 020c
luxeon r datasheet ds101 20130506 9 ? ? ? mechanical dimensions figure 1. package outline drawing. notes for figure 1: - do not handle the device by the lens. care must be taken to avoid damage to the lens or the interior of the device that can be damaged by excessive force to the lens. - drawings not to scale. all dimensions are in millimeters. - the thermal pad is electrically isolated from the anode and cathode contact pads.
luxeon r datasheet ds101 20130506 10 pad confguration note for figure 2: - the thermal pad is electrically isolated from the anode and cathode contact pads. solder pad design note for figure 3: - the photograph shows the recommended luxeon r layout on printed circuit board (pcb). this design easily achieves a thermal resistance of 7k/w. - application brief ab32 provides extensive details for this layout. printed circuit board layout fles (.dwg) are available at www.philipslumileds.com and www.philipslumileds.cn.com. 3 12 to p 3 21 bo tt om 3 thermal 2 anode 1 ca thode pa d function figure 2. pad confguration. figure 3. solder pad layout.
luxeon r datasheet ds101 20130506 11 typical light output characteristics over temperature all luxeon r emitters at test current 1.20 1 10 700ma d.c. 1 . 10 n ous flux 1.00 ized lumi n 0.90 normal 0.80 25 35 45 55 65 75 85 95 105 115 125 junction temperature tj (c) figure 4. relative light output vs. junction temperature.
luxeon r datasheet ds101 20130506 12 typical forward current characteristics all luxeon r emitters, junction temperature = 85c typical relative luminous flux vs. forward current for all luxeon r emitters, junction temperature = 85c 1200 1000 800 u rrect ma 600 forward c u 400 0 200 0 2.4 2.5 2.6 2.7 2.8 2.9 3 3.1 3.2 forward voltagev figure 5. forward current vs. forward voltage. 0.6 0.8 1 1.2 1.4 1.6 e lative luminous flux 0 0.2 0.4 0 200 400 600 800 1000 1200 r e forward current [ma] figure 6. typical relative luminous fux vs. forward current, junction temperature = 85oc.
luxeon r datasheet ds101 20130506 13 current derating curves current derating curve for 350 ma drive current all luxeon r emitters current derating curve for 700 ma drive current all luxeon r emitters 400 200 250 300 350 400 current ma 15 c/w 100 150 200 250 300 350 400 i f - forward current ma 15c/w 25c/w 35c/w 45c/w 0 50 100 150 200 250 300 350 400 0 25 50 75 100 125 150 175 i f - forward current ma t a - ambient temperature c 15c/w 25c/w 35c/w 45c/w 0 50 100 150 200 250 300 350 400 0 25 50 75 100 125 150 175 i f - forward current ma t a - ambient temperature c 15c/w 25c/w 35c/w 45c/w figure 7. maximum forward current vs. ambient temperature, based on t jmax = 150oc. 800 500 600 700 800 c urrent ma 1 c/w 200 300 400 500 600 700 800 i f - forward current ma 15c/w 25c/w 35c/w 0 100 200 300 400 500 600 700 800 0 25 50 75 100 125 150 175 i f - forward current ma t a - ambient temperature c 15c/w 25c/w 35c/w 0 100 200 300 400 500 600 700 800 0 25 50 75 100 125 150 175 i f - forward current ma t a - ambient temperature c 15c/w 25c/w 35c/w figure 8. maximum forward current vs. ambient temperature, based on t jmax = 150oc.
luxeon r datasheet ds101 20130506 14 current derating curve for 1000 ma drive current all luxeon r emitters 1200 600 800 1000 1200 a rd current ma 200 400 600 800 1000 1200 i f - forward current ma 15c/w 25c/w 0 200 400 600 800 1000 1200 0 25 50 75 100 125 150 175 i f - forward current ma t a - ambient temperature c 15c/w 25c/w figure 9. maximum forward current vs. ambient temperature, based on t jmax = 150oc.
luxeon r datasheet ds101 20130506 15 typical radiation patterns typical luminous intensity distribution pattern for luxeon r emitters 80% 90% 100% 50% 60% 70% 80% 90% 100% a tive intensity 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% relative intensity 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% -90 -75 -60 -45 -30 -15 0 15 30 45 60 75 90 relative intensity angular displacement (degrees) figure 10. cartesian plot of typical luminous intensity.
luxeon r datasheet ds101 20130506 16 emitter pocket tape packaging 1000 20 50
luxeon r datasheet ds101 20130506 17 emitter reel packaging
luxeon r datasheet ds101 20130506 18 product binning and labeling purpose of product binning in the manufacturing of semiconductor products, there is a variation of performance around the average values given in the technical data sheets. for this reason, philips lumileds bins the led components for luminous fux and forward voltage (v f ). color is offered in a single 5-step macadam ellipse color space centered on the ansi cct color bins. for additional information please review the macadam ellipse technical defnition section. decoding product bin labeling luxeon r emitters are labeled using a two digit alphanumeric code (cat code) depicting the bin values for emitters packaged on a single reel. all emitters packaged within a reel are of the same 2-variable bin combination. using these codes, it is possible to determine optimum mixing and matching of products for consistency in a given application. reels of luxeon r emitters are labeled with a two digit alphanumeric cat code following the format below. ab a = flux bin (j, k, l, m, n, p and q) b = v f bin (p, r, and s)
luxeon r datasheet ds101 20130506 19 table 7 lists the standard photometric luminous fux bins for luxeon r emitters (tested and binned at 700 ma d.c., junction temperature = 85c. minimum luminous fux performance within published operating conditions. philips lumileds maintains a tolerance of 6.5% on luminous fux measurements. although several bins are outlined, product availability in a particular bin varies by production run and by product performance. not all bins are available in all ccts. table 7. flux bins minimum photometric flux maximum photometric flux bin code (lm) (lm) g 160 170 h 170 180 j 180 190 k 190 200 l 200 210 m 210 220 n 220 230 p 230 240 q 240 250 r 250 260 s 260 270 t 270 280 note for table 7: 1. minimum luminous fux performance within published operating conditions. philips lumileds maintains a tolerance of 6.5% on luminous fux measurements. luminous flux bins
luxeon r datasheet ds101 20130506 20 luxeon r 5-step macadam ellipse color defnition tested at 700 ma d.c. & junction temperature = 85c table 8. luxeon r product characteristics part nominal color center point major axis, minor axis, ellipse number ansi cct space (cx, cy) a b rotation angle lxa7-pw30 3000k single 5-step macadam ellipse 0.4338, 0.4030 0.01390 0.00680 53.22 lxa7-pw40 4000k single 5-step macadam ellipse 0.3818, 0.3797 0.01565 0.00670 53.72 LXA7-PW50 5000k single 5-step macadam ellipse 0.3447, 0.3553 0.01370 0.00590 59.62 lxa7-pw57 5700k single 5-step macadam ellipse 0.3287, 0.3417 0.01243 0.00533 59.09 lxa7-pw65 6500k single 5-step macadam ellipse 0.3123, 0.3282 0.01115 0.00475 58.57 note for table 8: - philips lumileds maintains a tester tolerance of 0.005 on x, y color coordinates.
luxeon r datasheet ds101 20130506 21 forward voltage bins table 9 lists minimum and maximum v f bin values per emitter (tested and binned at 700 ma). although several bins are outlined, product availability in a particular bin varies by production run and by product performance. table 9. v f bins minimum forward voltage maximum forward voltage bin code (v) (v) p 2.50 2.75 r 2.75 3.00 s 3.00 3.25
company information ?2013 philips lumileds lighting company. all rights reserved. product specifcations are subject to change without notice. www.philipslumileds.com www.philipslumileds.cn.com philips lumileds is a leading provider of leds for everyday lighting applications. the companys records for light output, effcacy and thermal management are direct results of the ongoing commitment to advancing solid-state lighting technology and enabling lighting solutions that are more environmentally friendly, help reduce co 2 emissions and reduce the need for power plant expansion. philips lumileds luxeon ? leds are enabling never before possible applications in outdoor lighting, shop lighting, home lighting, consumer electronics, and automotive lighting. philips lumileds is a fully integrated supplier, producing core led material in all three base colors, (red, green, blue) and white. philips lumileds has r&d centers in san jose, california and in the netherlands, and production capabilities in san jose, singapore and penang, malaysia. founded in 1999, philips lumileds is the high fux led technology leader and is dedicated to bridging the gap between solid-state technology and the lighting world. more information about the companys luxeon led products and solid-state lighting technologies can be found at www.philipslumileds.com.

▲Up To Search▲

Price & Availability of LXA7-PW50

	To Download LXA7-PW50 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .