![]() |
|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
d o c u m e nt ve r s i o n 0.1 1/33 p r od u ct s p ecificati on b121e w 02 v1 a u optronics corpor a tion produ ct s pecification 12.1 w x g a c olor t f t -lcd m odule m odel na m e : b121e w 02 v1 approved b y prepared b y mdbu marketing division / au optronics corporation custo m er chec k ed & approved b y www.datasheet.co.kr datasheet pdf - http://www..net/
document version 0.1 2/33 product specification b121ew02 v1 product specification 12.1 wxga color tft-lcd module model name: b121ew02 v.1 ( ) preliminary specifications ( v ) final specifications note: this specification is subject to change without notice. www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 3/33 product specification b121ew02 v1 contents 1. handling precautions...............................................................5 2. general description.................................................................6 2.1 display characteristics....................................................................................................................6 2.2 optical characteristics....................................................................................................................7 3. functional block diagram......................................................12 4. absolute maximum ratings....................................................13 4.1 absolute ratings of tft lcd module..........................................................................................13 4.2 absolute ratings ofbacklight unit................................................................................................13 4.3 absolute ratings of environment..................................................................................................13 5. electrical characteristics........................................................14 5.1 tft lcd module.........................................................................................................................14 5.2 backlight unit...............................................................................................................................16 6. signal characteristic..............................................................18 6.1 pixel format image.......................................................................................................................18 6.2 the input data format....................................................................................................................19 6.3 signal description.........................................................................................................................20 6.4 interface timing............................................................................................................................22 7. connector & pin assignment..................................................24 7.1 tft lcd module.........................................................................................................................24 (b) signal pin.....................................................................................................................................24 7.2 backlight unit...............................................................................................................................25 7.3 signal for lamp connector............................................................................................................25 8. vibration and shock test.......................................................26 8.1 vibration test...............................................................................................................................26 8.2 shock test spec:..........................................................................................................................26 9. reliability..............................................................................27 10. mechanical characteristics...................................................28 10.1 lcm outline dimension.............................................................................................................28 10.2 screw hole depth and center position.......................................................................................29 11. shipping and package..........................................................30 11.1 shipping label format................................................................................................................30 11.2. carton package..........................................................................................................................31 11.3 shipping package of palletizing sequence....................................................................................31 www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 4/33 product specification b121ew02 v1 record of revision version and date page old description new description remark 0.1 2005/07/20 all first edition for customer 0.2 2006/01/06 6.7.16 brightness tolerance +/10% brightness tolerance +/15% www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 5/33 product specification b121ew02 v1 1. handling precautions 1) since front polarizer is easily damaged, pay attention not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact with water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) in case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the ccfl reflector edge. instead, press at the far ends of the cfl reflector edge softly. otherwise the tft module may be damaged. 10) at the insertion or removal of the signal interface connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an enclosure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp in lcd contains a small amount of mercury. please follow local ordinances or regulations for disposal. 13) small amount of materials having no flammability grade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source(, iec60950 or ul1950), or be applied exemption. 14) the lcd module is designed so that the cfl in it is supplied by limited current circuit(iec60950 or ul1950). do not connect the cfl in hazardous voltage circuit. www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 6/33 product specification b121ew02 v1 2. general description b121ew02 v1is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen format is intended to support the wxga (1280(h) x 800(v)) screen and 262k colors (rgb 6-bits data driver). all input signals are lvds interface compatible. inverter card of backlight is not included. b121ew02 v1 is designed for a display unit of notebook style personal computer and industrial machine. 2.1 display characteristics the following items are characteristics summary on the table under 25 condition: items unit specifications screen diagonal [mm] 307.9 (12.1w ) active area [mm] 261.12(h) x 163.2(v) pixels h x v 1280x3(rgb) x 800 pixel pitch [mm] 0.204x0.204 pixel arrangement r.g.b. vertical stripe display mode normally white typical white luminance (icfl=6.0ma) [cd/m 2 ] 200 typ. (5 points average) 170 min. (5 points average) (note1) luminance uniformity 1.25 max. (5 points) contrast ratio 400 typ. optical rise time/fall time [msec] 10/15 typ. nominal input voltage vdd [volt] +3.3 typ. typical power consumption [watt] 5w max. ( ebl 3w ) weight [grams] 295g typ. 310g max physical size [mm] 275.82x 178 x 5.5 max.5.5max electrical interface 1 channel lvds surface treatment glare, harness 2h, haze 25%, reflectance 4.3% support color native 262k colors ( rgb 6-bit data driver ) www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 7/33 product specification b121ew02 v1 temperature range operating storage ( non - operating) [ o c] [ o c] 0 to +50 - 40 t o +60 rohs compliance rohs compliance 2.2 optical characteristics the optical characteristics are measured under stable conditions at 25 (room temperature): item unit conditions min. typ. max. note white luminance ccfl 6.0ma [cd/m2] 5 points average 170 200 - 1,2,3 [degree] [degree] horizontal (right) cr = 10 (left) - - 60 60 - - viewing angle [degree] [degree] vertical (upper) cr = 10 (lower) - - 50 50 - - 2,7 uniformity 5 points 1.25 uniformity 13 points 1.6 1 cr: contrast ratio 350 400 - 6 cross talk % 4 4 [msec] rising - 10 15 [msec] falling - 15 20 response time [msec] raising + falling 25 35 5 red x 0.564 0.594 0.624 red y 0.305 0.335 0.365 green x 0.298 0.328 0.358 green y 0.501 0.531 0.561 blue x 0.122 0.152 0.182 blue y 0.113 0.143 0.173 white x 0.283 0.313 0.343 color / chromaticity coordinates (cie 1931) white y 0.299 0.329 0.359 2,7 note 1: 5 points position (display area : 261.12mm x 163.2mm) www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 8/33 product specification b121ew02 v1 12 3 45 h/4 h/4 h/4 h/4 h w w/4 w/4 w/4 w/4 note 2: 13 points position w/4 w w/4 h h/4 h/4 h/4 h/4 7 9 10 w/4 1 8 w/4 10 10 10 10 2 3 13 12 4 5 6 11 note 3: the luminance uniformity of 5 and 13 points is defined by dividing the maximum luminance values by the minimum test point luminance w13 = maximum brightness of thirteen points minimum brightness of t hirteen points maximum brightness of five points w5 = minimum brightness of five points www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 9/33 product specification b121ew02 v1 note 4: measurement method the lcd module should be stabilized at given temperature for 30 minutes to avoid abrupt temperature change during measuring. in order to stabilize the luminance, the measurement should be executed after lighting backlight for 30 minutes in a stable, windless and dark room. note 5 definition of cross talk (ct) ct = | y b C y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) center of the screen tft - lcd 50 cm photo detector lcd panel field=2 www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 10/33 product specification b121ew02 v1 note 6: definition of response time: the output signals of bm-7 or equivalent are measured when the input signals are changed from black to white (falling time) and from white to black (rising time), respectively. the response time interval between the 10% and 90% of amplitudes. refer to figure as below. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 11/33 product specification b121ew02 v1 note 7. definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal viewing angles). the 180 viewing angle range is broken down as follows; 90 ( ) horizontal left and right and 90 ( ) vertical, high (up) and low (down). the measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 12/33 product specification b121ew02 v1 3. functional block diagram the following diagram shows the functional block of the 12.1 inches wide color tft/lcd module: tft array/cell vdd lcd controller lcd drive card backlight unit 1280(r/g/b) x 3 x 800 gnd dc-dc converter ref circuit y-driver x-driver rxin0 rxin1 rxin2 rxclkin (4 pairs lvds) hirose df19l-20p-1h mating type df19g-20s-1c or compatible jst bhsr-02vs-1 mating type sm02b-bhss-1- tb lamp connector(2pin) l cd connector( 20 pin) www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 13/33 product specification b121ew02 v1 4. absolute maximum ratings absolute maximum ratings of the module is as following: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings ofbacklight unit item symbol min max unit conditions ccfl current icfl - 7 [ma] rms note 1,2 4.3 absolute ratings of environment item symbol min max unit conditions operating temperature top 0 +50 [ o c] note 3 operation humidity hop 5 95 [%rh] note 3 storage temperature tst -40 +60 [ o c] note 3 storage humidity hst 5 95 [%rh] note 3 note 1: with in ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality perfermance, please refer to auo iis(incoming inspection standard). twb=39 c operating range storage range www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 14/33 product specification b121ew02 v1 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; symble parameter min typ max units condition vdd logic/lcd drive voltage 3.0 3.3 3.6 volt load capacitance 20uf pdd vdd power - 1.0 - watt] max: all black pattern idd idd current - 303 - ma max:all black pattern i rush inrush current - - 1800 ma vddrp allowable logic/lcd drive ripple voltage - - 500 [mv] p-p vddns allowable logic/lcd drive ripple noise - - 100 [mv] p-p note 1 : measurement conditions: q3 ao6402 g d 2 s d 1 d 5 d 6 q3 ao6402 g d2 s d1 d5 d6 c1 1uf/16v c2 1uf/25v c3 0.01uf/25v f1 vr1 47k +12.0v vcc sw1 sw mag-spst 1 2 (high to low) control signal (lcd module input) r2 1k +3.3v r1 47k r2 1k 90% 10% vin rising time 0v 3.3v 0.5ms www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 15/33 product specification b121ew02 v1 5.1.2 signal electrical characteristics input signals shall be low or hi-z state when vdd is off. it is recommended to refer the specifications. note: lvds signal waveform item symbol min. typ. max. unit condition differential input voltage vid 0.1 - 0.6 v lvds input common mode voltage vcm 1 1.2 1.5 v vth/vtl=+-100mv differential input high threshold voltage vth - - 100 mv differential input low threshold voltage vtl -100 - - mv vcm=1.2v www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 16/33 product specification b121ew02 v1 5.2 backlight unit parameter guideline for ccfl inverter parameter min typ max units condition white luminance 5 points average 170 200 - [cd/m 2 ] (ta=25 ) ccfl current(icfl) 5.5 6.0 6.5 [ma] rms (ta=25 ) note 2 ccfl frequency(fcfl) 50 60 70 [khz] (ta=25 ) note 3,4 ccfl ignition voltage(vs) 1400 - - [volt] rms (ta= 0 ) note 5 ccfl voltage (reference) (vcfl) - 580 - [volt] rms (ta=25 ) note 6 ccfl power consumption (pcfl) - 3.5 - [watt] (ta=25 ) note 6 note 1: typ are auo recommended design points. *1 all of characteristics listed are measured under the condition using the auo test inverter. *2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes appear on the screen, and substandard luminance or flicker at low power may happen. *3 in designing an inverter, it is suggested to check safety circuit very carefully. impedance of cfl, for instance, becomes more than 1 [m ohm] when cfl is damaged. *4 generally, cfl has some amount of delay time after applying kick-off voltage. it is recommended to keep on applying kick-off voltage for 1 [sec] until discharge. *5 cfl discharge frequency must be carefully chosen so as not to produce interfering noise stripes on the screen. *6 reducing cfl current increases cfl discharge voltage and generally increases cfl discharge frequency. so all the parameters of an inverter should be carefully designed so as not to produce too much leakage current from high-voltage output of the inverter. note 2: it should be employed the inverter which has duty dimming , if icfl is less than 4ma. note 3: cfl discharge frequency should be carefully determined to avoid interference between inverter and tft lcd. note 4: the frequency range will not affect to lamp life and reliability characteristics. note 5: cfl inverter should be able to give out a power that has a generating capacity of over 1,430 voltage. lamp units need 1,400 voltage minimum for ignition. note 6: calculator value for reference (icfl vcfl=pcfl) www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 17/33 product specification b121ew02 v1 note 7: requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. it shall help increase the lamp lifetime and reduce leakage current. a. the asymmetry rate of the inverter waveform should be less than 10%. b. the distortion rate of the waveform should be within 2 10%. * inverter output waveform had better be more similar to ideal sine wave. www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 18/33 product specification b121ew02 v1 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the input signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 0 1 1278 1279 1st line 800th line www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 19/33 product specification b121ew02 v1 6.2 the input data format signal name description r5 r4 r3 r2 r1 r0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. g5 g4 g3 g2 g1 g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of these 6 bits pixel data. b5 b4 b3 b2 b1 b0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the signal is used to strobe the pixel data. de display timing when the signal is high, the pixel data shall be valid to be displayed. vs vertical sync vertical synchronized signal hs horizontal sync horizontal synchronized signal note: output signals from any system shall be low or hi-z state when vdd is off. www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 20/33 product specification b121ew02 v1 6.3 signal description signal name description rxin0n, rxin0p lvds differential data input (r0~r5, g0) rxin1n, rxin1p lvds differential data input (g1~g5, b0~b1) rxin2n, rxin2p lvds differential data input (b2~b5, hsync, vsync, de) rxclkinn, rxclkinp lvds differential clock input vdd +3.3v power supply gnd ground note1: start from right side note2: please follow vesa. note3: input signals shall be low or hi-z state when vdd is off. internal circuit of lvds inputs are as following. connector 20 1 g n d g n d www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 21/33 product specification b121ew02 v1 the module uses a 100ohm resistor between positive and negative data lines of each receiver input r r r r signal input pin no. 9 11 12 14 15 17 18 8 rxin0+ rxin0- rxin1+ rxin1- rxin2+ rxin2- rxclkin+ rxclkin- lvds receiver www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 22/33 product specification b121ew02 v1 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1280x800 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate - 50 60 - hz clock frequency 1/ t clock 62 68.9 75 mhz period t v 803 816 832 active t vd 800 800 800 vertical section blanking t vb 3 16 32 t line period t h 1302 1408 1700 active t hd - 1280 - horizontal section blanking t hb 22 128 420 t clock note : de mode only 6.4.2 timing diagram dotclk de t h t hb t hd de t v t vb t vd input timing definition ( de mode) t clock input data pixel 1 pixel 2 pixel 3 pixel n-1 pixel n invaild data invaild data pixel 1 www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 23/33 product specification b121ew02 v1 6.5 power on/off sequence vdd power and lamp on/off sequence is as follows. interface signals are also shown in the chart. signals from any system shall be hi-z state or low level when vdd is off. power sequence timing value parameter min. typ. max. units t1 0.5 - 10 (ms) t2 0 - 50 (ms) t3 0 - 50 (ms) t4 500 - - (ms) t5 200 - - (ms) t6 200 - - (ms) t7 0 - 10 (ms) t4 t3 t2 t5 valid data t1 10% 90% 10% 90% t6 t 7 power supply vdd lvds interface backlight on www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 24/33 product specification b121ew02 v1 7. connector & pin assignment physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. 7.1 tft lcd module (a) connector connector name / designation for signal connector manufacturer hirose type / part number df19l-20p-1h mating housing/part number df19g-20s-1c or compatible (b) signal pin pin# signal name pin# signal name 1 gnd 2 vdd 3 vdd 4 vdd edid 5 aging 6 clk edid 7 data edid 8 rxin0n 9 rxin0p 10 gnd 11 rxin1n 12 rxin1p 13 gnd 14 rxin2n 15 rxin2p 16 gnd 17 rxclkinn 18 rxclkinp 19 gnd 20 gnd www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 25/33 product specification b121ew02 v1 7.2 backlight unit physical interface is described as for the connector on module. these connectors are capable of accommodating the following signals and will be following components. connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1-tb 7.3 signal for lamp connector pin # cable color signal name 1 red lamp high voltage 2 white lamp low voltage www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 26/33 product specification b121ew02 v1 8. vibration and shock test 8.1 vibration test test spec: l test method: non-operation l acceleration: 1.5g l frequency: 26 - 500hz random l sweep: 30 minutes each axis (x, y, z) 8.2 shock test spec: test spec: l test method: non-operation l acceleration: 220 g , half sine wave l active time: 2 ms l pulse: x,y,z .one time for each side www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 27/33 product specification b121ew02 v1 9. reliability items required condition note temperature humidity bias 40 /95%,250hr high temperature operation 50 /dry,250hr low temperature operation 0 ,250hr on/off test on/30 sec. off/30sec., 30,000 cycles. hot storage 65 /20% rh ,250 hours cold storage -40 /50% rh ,250 hours thermal shock test -40 /20 min ,65 /20 min 50cycles hot start test 50 /1 hr min. power on/off per 5 minutes, 5 times cold start test 0 /1 hr min. power on/off per 5 minutes, 5 times shock test (non-operating) 220g, 2ms, half-sine wave vibration test (non-operating) random vibration, 1.5 g zero-to-peak, 26 to 500 hz, 30 mins in each of three mutually perpendicular axes. esd contact : 8kv/ operation air : 15kv / operation note 1 room temperature test 25 , 2000hours, operating with loop pattern note1: according to en61000-4-2 , esd class b: some performance degradation allowed. no data lost . self-recoverable. no hardware failures. note2: ccfl life time: 10,000 hours minimum under normal module usage. note3: mtbf (excluding the ccfl): 30,000 hours with a confidence level 90% www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 28/33 10. mechanical characteristics 10.1 lcm outline dimension www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 29/33 10.2 screw hole depth and center position screw hole minimum depth, from side surface =2.5 mm (see drawing) screw hole center location, from front surface = 3.7 0.2mm (see drawing) screw torque: maximum 2.5 kgf-cm www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 30/33 11. shipping and package 11.1 shipping label format note 1 note 1: ic combination control code h/w source ic:nt gate ic: nt oaxxx oa source gate ic: nec 1axxx 1a www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 31/33 11.2. carton package the outside dimension of carton is 486 (l)mm x 286 (w)mm x 360 (h)mm 11.3 shipping package of palletizing sequence top cardboard wooden pallet bottom cardboard corner angle stretch film pe band note : limit of box palletizing = max 3 layers(ship and stock conditions) www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 32/33 www.datasheet.co.kr datasheet pdf - http://www..net/ document version 0.1 33/33 www.datasheet.co.kr datasheet pdf - http://www..net/ |
Price & Availability of B121EW02V1
![]() |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |