mmd monitor/quartztek 30400 esperanza, rancho santa margarita, ca, 92688 phone: (949) 709-5075, fax: (949) 709-3536, www.mmdcomp.com sales@mmdcomp.com revision: 10/29/10 d revisions only with customer approval pg 1 of 2 m m v v l l p p , , m m v v l l l l & & m m v v l l v v s s e e r r i i e e s s v v c c x x o o ?? mil-std-883 level b screening available ?? available to -55 c to + 125 c operating ?? rohs compliant ?? less than 1 psec jitter marking detail line 1 = mxxxxx m = mmd xxxxx = frequency in mhz line 2 = syywwl s = internal code yyww = 4 numerical digit date code (year / week) jan 27 2011=1105 l = denotes rohs compliant line 3 = xxxxx internal use only may vary with lots black dot to denote pin 1 lvds lvpecl pecl frequency range 70.000mhz to 800.000mhz frequency stability* (see part number guide for options) operating temp.range (see part number guide for options) storage temp. range -55c to +125c aging 5 ppm / yr max logic ?0? 1.43v typ vdd ? 1.620 vdc max vdd ? 1.620 vdc max logic ?1? 1.10v typ vdd- 1.025 vdc min vdd- 1.025 vdc min supply voltage (vdd) supply current +2.5vdc 5% 50 ma max 50 ma max n/a +3.3vdc 5% 60 ma max 60 ma max n/a +5.0vdc 5% n/a n/a 140 ma max symmetry (50% of waveform) (see part number guide for options) rise / fall time (20% to 80%) 2nsec max load 50 ohms into vdd-2.00 vdc start time 10msec max phase jitter (12khz to 20mhz) less than 1 psec tri-state operation vih = 70% of vdd min to enable output vil = 30% max or grounded to disable output (high impedance) * inclusive of temp., load, voltage and aging control voltage (vc) +2.5vdc 1.25vdc 1.00vdc 1.25vdc 1.00vdc n/a +3.3vdc 1.65vdc 1.50vdc 1.65vdc 1.50vdc n/a +5.0vdc n/a 2.50vdc 2.00vdc pullability (see part number guide for options) linearity (see part number guide for options) n/a environmental & mechanical detail shock mil-std-883, method 2002 cond b solderability mil-std-883, method 2003 solvent re- sistance mil-std-202, method 215 vibration mil-std-883, method 2007, cond a gross leak test mil-std-883, method 1014, cond c fine leak test mil-std-883, method 1014, cond a2 msl level 1 per ipc/jedec j-std 20
mmd monitor/quartztek 30400 esperanza, rancho santa margarita, ca, 92688 phone: (949) 709-5075, fax: (949) 709-3536, www.mmdcomp.com sales@mmdcomp.com revision: 10/29/10 d revisions only with customer approval pg 2 of 2 mvl frequency output p = pecl l = lvpecl v = lvds *option b (47.5/52.5%) available up to 500mhz only please consult with mmd sales deparment for any other parameters or options linearity blank = 20% max x = 5% max z = 15% max y = 10% max operating temperature blank = 0c to +70c 27 = -20c to +70c 48 = -40c to +85c pullability a = 200 ppm min c = 100 ppm min d = 50 ppm min p = 25 ppm min frequency stability 020 = 20 ppm 025 = 25 ppm 050 = 50 ppm 100 = 100 ppm supply voltage 2 = +2.5 vdc 3 = +3.3 vdc 5 = +5.0 vdc symmetry * blank = 40%/60% a = 45%/55% b = 47.5%/52.5% 55 = -55c to +125c pin 1 pin 2 pin 3 pin 4 pin 5 pin 6 voltage control enable/disable ground output comp. output supply voltage pin connections external bypass capacitor is recommended dimension in brackets are in inches recommended land pattern 9.80 [.386] max 14.00 [.551] max 4.70 [.185] max 2.54 [.100] 5.08 [.200] 0.84 [.033] denotes pin 1 1 2 34 5 6 7.87 [.310] 2.54 [.100] 5.08 [.200] 1.02 [.040] 2.50 [.098] mxxxxx syywwl xxxxx pitch pitch 4.00 [.157] tape width 12.00 [.471] direction of feed 180 [7.0] reel dia reel dia q1 q2 q3 q4 q1 q2 q4 q3 500 qty per reel pin 1 orient. q1 tape width notes: unless otherwise specified 1. applicable standards / specifications ansi y14.5m , dimensions and tolerances eia-481-b , 8 mm through 200mm embossed carrier taping and 8 mm and 12 mm punched carrier taping of surface mount components for automatic handling. 2. dimensions are in millimeters [inch]. 3. tolerances are 0.1 [.004] mm unless otherwise specified. 4. do not scale drawing. part number guide mechanical details tape & reel dimensions
|