TQL9042 500 C 2000 mhz bypass lna datasheet: rev . e 0 3 - 1 9 - 1 5 - 1 of 9 - disclaimer: subject to change without notice ? 201 5 triquint www.triquint.com applications ? ? ? ? ? 1 0 - pin 3 ? ? product features ? ? C ? ? ? ? ? ? ? ? ? ? ? ? ? ? functional block diagram general description the TQL9042 is a high - linearity, ultra - low noise gain block amplifier with a bypass mode functionality integrated in the product. at 900 m hz, the amplifier typically provides 19 db gain, +36 dbm oip3, and 0. 42 db noise figure while drawing 70 ma current from a + 5 ? ? C ? ? ? ? ? C ? ? C ? pin configuration pin no. label 1 v ctrl2 2, 4, 7, 9 n /c 3 rf in 5 gnd 6 v dd 8 rfout 10 v ctrl1 backside paddle rf/dc gnd ordering information part no. description TQL9042 500 ? C ? standard t/r size = 2500 pieces on a 7 reel b a c k s i d e p a d - r f / d c g n d p i n 1 r e f e r e n c e m a r k p a c k a g e t o p s i d e v c t r l 1 n / c r f o u t n / c v d d v c t r l 2 n / c r f i n n / c g n d 1 0 9 8 7 1 2 3 4 5 6
TQL9042 500 C 2000 mhz bypass lna datasheet: rev . e 0 3 - 1 9 - 1 5 - 2 of 9 - disclaimer: subject to change without notice ? 201 5 triquint www.triquint.com absolute maximum ratings parameter rating storage temperature ? ? dd ) + 7 v input power (cw) + 2 2 dbm operation of this device outside the parameter ranges given above may cause permanent damage. recommended operating conditions parameter min typ m ax units drain voltage (v dd ) + 3.3 +5.0 +5 .25 v operating temp. range ? ch (for>10 6 hrs mttf ) + 190 c electrical specifications are measured at specified test conditions. specifications are not guaranteed over all recommended operating co nditions. electrical specifications test conditions unless otherwise noted: v dd = +5 v, temp.=+ 25 ? c . parameter conditions min typ max units operational frequency range 5 00 2 000 mhz test frequency 900 mhz gain bypass off 17.5 1 9 20.5 db in put return loss bypass off 1 1 db output return loss bypass off 20 db noise figure bypass off 0. 42 0.8 db output p1db bypass off + 23 dbm output ip3 bypass off, pout=+ 5 dbm/tone, f=1 mhz dbm/tone, f=1 mhz 1 , v 2 (1) v ih 2.4 v dd v v il 0 0.4 v current, i d bypass off 40 70 110 ma bypass on 3 4.5 ma switching speed by pass to lna mode 9 26 ns lna to bypass mode 55 ns thermal resistance, jc channel to case 100 c/w notes: 1. the limits shown are true when using the external resistive divider values as shown on the triquint app board . control voltage limit s (at device pins) state bias condition v ctrl1 low 0.1 v high 0.52 v v ctrl2 low 0.4 v high 1.3 v control truth table v ctrl2 v ctrl1 state 0 1 lna off, bypass off 1 1 lna off, bypass on 0 0 lna on, bypass off 1 0 reserved (do not u se)
TQL9042 500 C 2000 mhz bypass lna datasheet: rev . e 0 3 - 1 9 - 1 5 - 3 of 9 - disclaimer: subject to change without notice ? 201 5 triquint www.triquint.com tq l9042 - pcb evaluation board see evaluation board pcb information section for pcb material and stack - up. note: if a TQL9042 application requires only two operational modes, lna and bypass, the modes may be set using a single control voltage with the control lines tied together as shown above right. the corresponding truth table is shown below. control truth table C 2 mode operation v 1 state 1 lna off, bypass on 0 lna on, bypass off bill of material C tq l90 42 - pcb reference des. value description manuf. part number u1 n/a bypass lna triquint tql 9042 c1, c2, c3, c4, c5 100 pf cap, 0402, +/ - 5%, 50v panasonic ecj - 0ec1h101j c6 1.0 uf cap , 0402, 10%, 10v, x5r various r1, r2 0 ? power - up and power - down sequencing v dd v ctrl1 & v ctrl2 lna on, bypass off power - up 1 st 2 nd power - down 1 st 2 nd lna off, bypass on power - up 1 st 2 nd power - down 1 st 2 nd u 1 c 1 c 2 r 2 r 3 r 4 l 1 c 5 c 6 r 1 c 3 c 4 j 2 r f o u t p u t j 8 g n d j 3 v d d j 1 r f i n p u t c 2 1 0 0 p f c 1 1 0 0 p f r 3 3 6 k ? j 5 v 1 j 4 v 2 r 2 0 ? u 1 r 4 1 0 k ? 1 0 9 8 7 1 2 3 4 5 6 l 1 6 8 n h 0 6 0 3 c 5 1 0 0 p f c 6 1 u f r 1 0 ? r 3 3 6 k ? v 1 r 2 0 ? o p t i o n a l s i n g l e c o n t r o l v o l t a g e c o n f i g u r a t i o n f o r 2 m o d e o p e r a t i o n
TQL9042 500 C 2000 mhz bypass lna datasheet: rev . e 0 3 - 1 9 - 1 5 - 4 of 9 - disclaimer: subject to change without notice ? 201 5 triquint www.triquint.com typical performance (bypass mode) test conditions unless otherwise noted: v dd = +5 v, i d = 3 ma, temp.=+25 ? c . parameter typical value units frequency 700 800 900 1000 m hz insertion loss 0.95 0.96 0.98 1 .00 db input return loss 12.5 12.6 12.7 12.6 db output return loss 13.1 13.4 13.6 13.7 db input ip3 (p in /tone= +6 dbm, f = 1 mhz ) + 41. 2 + 40. 8 + 43 .0 + 40 .2 dbm typical performance (lna mode) test conditions unless otherwise noted: v dd = +5 v, i d = 70 ma, temp.=+25 ? c . parameter typical value units frequency 700 800 900 1000 m hz gain 20.8 19.9 19 .0 18.2 db noise figure 0. 37 0. 3 7 0.4 2 0. 46 db input return loss 9.6 10.2 10.8 11.4 db output return loss 21 .0 20.4 19.8 19.1 db output p1db + 23.1 + 23.1 + 23.1 + 23.2 dbm o ip3 (p out /tone= +5 dbm, f = 1 mhz ) + 35.3 + 35.5 + 36 .0 + 36 .0 dbm typical performance (lna off, bypass off mode) test conditio ns unless otherwise noted: v dd ? = ? +5 ? v, temp. ? = ? +25 ? c. parameter typical value units frequency 700 800 900 1000 mhz isolation 6.6 7.4 8.2 8.8 db
TQL9042 500 C 2000 mhz bypass lna datasheet: rev . e 0 3 - 1 9 - 1 5 - 5 of 9 - disclaimer: subject to change without notice ? 201 5 triquint www.triquint.com performance plots test conditions unless otherwise noted: v dd = +5 v, i d = 70 ma, temp.=+25 ? c 0 5 10 15 20 25 30 500 800 1100 1400 1700 2000 gain (db) frequency (mhz) gain vs. frequency (lna mode) +85 c +25 c ?40 c - 20 - 15 - 10 - 5 0 500 800 1100 1400 1700 2000 |s11| (db) frequency (mhz) input return loss vs. frequency (lna mode) +85 c +25 c ?40 c - 25 - 20 - 15 - 10 - 5 0 500 800 1100 1400 1700 2000 |s22| (db) frequency (mhz) output return loss vs. frequency (lna mode) +85 c +25 c ?40 c - 5 - 4 - 3 - 2 - 1 0 500 800 1100 1400 1700 2000 gain (db) frequency (ghz) gain vs. frequency (bypass mode) +85 c +25 c ?40 c - 15 - 14 - 13 - 12 - 11 - 10 500 800 1100 1400 1700 2000 |s11| (db) frequency (mhz) input return loss vs. frequency (bypass mode) +85 c +25 c ?40 c - 15 - 14 - 13 - 12 - 11 - 10 500 800 1100 1400 1700 2000 |s22| (db) frequency (mhz) output return loss vs. frequency (bypass mode) +85 c +25 c ?40 c 30 32 34 36 38 40 700 750 800 850 900 950 1000 oip3 (dbm) frequency (mhz) oip3 vs. frequency (lna mode) pout=+5 dbm / tone 1 mhz tone spacing +85 c +25 c ?40 c 35 37 39 41 43 45 700 750 800 850 900 950 1000 iip3 (dbm) frequency (mhz) iip3 vs. frequency (bypass mode) +85 c +25 c ?40 c pin=+6 dbm / tone 1 mhz tone spacing 21 22 23 24 25 26 700 750 800 850 900 950 1000 p1db (dbm) frequency (mhz) p1db vs. frequency ?40 c +25 c +85 c 0.0 0.2 0.4 0.6 0.8 1.0 700 750 800 850 900 950 1000 nf (db) frequency (mhz) noise figure vs. frequency ?40 c +25 c +85 c - 20 - 15 - 10 - 5 0 500 800 1100 1400 1700 2000 isolation (db) frequency (ghz) isolation vs. frequency (lna off, bypass off) temp.=+25 c
TQL9042 500 C 2000 mhz bypass lna datasheet: rev . e 0 3 - 1 9 - 1 5 - 6 of 9 - disclaimer: subject to change without notice ? 201 5 triquint www.triquint.com switching speed switching speed measurement on tqs application board transition measurements units bypass to lna mode (50% v1/v2 C 10% rf) 926 ns lna to bypass mode (50% v1/v2 C 90% rf) 55.5 ns bypass to lna mode (50% v1 /v2 C lna to bypass mode (50% v1/v2 C rf signal control signal control signal rf signal freq = 900 mhz fm = 1 khz pout = 5 dbm freq = 900 mhz fm = 1 k hz pout = 5 dbm
TQL9042 500 C 2000 mhz bypass lna datasheet: rev . e 0 3 - 1 9 - 1 5 - 7 of 9 - disclaimer: subject to change without notice ? 201 5 triquint www.triquint.com pin configuration and description pin no. label description 1 v ctrl2 control pin for bypass mode and lna mode. internal resistor divider. refer to truth table. 2, 4, 7, 9 n /c no internal connection. provide grounded pcb land pads for mounting integrity. 3 rfin rf input pin. dc block required. 5 gnd rf/dc ground pin. 6 v dd supply voltage pin. 8 rfout rf output pin. dc block required. 10 v ctrl1 control pin for bypass mode a nd lna mode. requires external resistor divider. refer to truth table. backside paddle rf/dc gnd rf/dc ground. follow recommended via pattern and ensure good solder attach for best thermal and electrical performance. evaluation board pcb information triquint pcb 1100233 material and stack - up 50 ohm line dimensions: width = .020, spacing = .032 b a c k s i d e p a d - r f / d c g n d p i n 1 r e f e r e n c e m a r k p a c k a g e t o p s i d e v c t r l 1 n / c r f o u t n / c v d d v c t r l 2 n / c r f i n n / c g n d 1 0 9 8 7 1 2 3 4 5 6 r o g e r s 4 3 5 0 b 1 o z . c u b o t t o m l a y e r r o g e r s 4 3 5 0 b r o g e r s 4 4 5 0 f 1 o z . c u t o p l a y e r 1 o z . c u i n n e r l a y e r 1 o z . c u i n n e r l a y e r 0 . 0 6 2 " 0 . 0 0 6 " f i n i s h e d b o a r d t h i c k n e s s 0 . 0 1 0 " 0 . 0 1 0 "
TQL9042 500 C 2000 mhz bypass lna datasheet: rev . e 0 3 - 1 9 - 1 5 - 8 of 9 - disclaimer: subject to change without notice ? 201 5 triquint www.triquint.com mechanical information package marking and dimensions marking: part number C C C notes: 1. all dimensions are in millimeters. angles are in degrees. 2. except where noted, this part outline conforms to jedec standard mo - 22 9 . 3. dimension and tolerance formats conform to asme y14.4m - 1994. 4. the terminal #1 identifier and terminal numbering conform to jesd 95 - 1 spp - 0 12. pcb mounting pattern notes: 1. all dimensions are in millimeters. angles are in degrees. 2. use 1 oz. copper minimum for top and bottom layer metal. 3. vias are required under the backside paddle of this device for proper rf/dc grounding and therma l dissipation. we recommend a 0.35mm (#80/.0135") diameter bit for drilling via holes and a final plated thru diameter of 0.25 mm (0.10). 4. ensure good package backside paddle solder attach for reliable operation and best electrical performance. 90 42 yyww axxxx 3 top view side view bottom view pin #1 identifier chamfer 0.300 x 45 3.0000.050 3.0000.050 1.6000.050 exp. dap 0.4000.050 2.4000.050 exp. dap 0.500 bsc 0.2500.050 0.203 ref 0.000-0.053 0.8500.050 pin #1 identifier 2.000 ref. 0.757 0.377 0.500 2.527 0.158 1.727 land pattern solder mask 0.500 0.250 0.630 0.508 0.508 0.285 1.600 12x 3
TQL9042 500 C 2000 mhz bypass lna datasheet: rev . e 0 3 - 1 9 - 1 5 - 9 of 9 - disclaimer: subject to change without notice ? 201 5 triquint www.triquint.com p roduct compliance information esd sensitivity caution! esd - sensitive device esd rating: class 1a value: 250v to 500v ? ? solderability comp atible with both lead - free (260 c max. reflow temperature) and tin/lead (245 c max. reflow temperature) soldering processes. package contact plating: nipdau rohs compliance this part is compliant with eu 2002/95/ec rohs directive (restrictions on the use of certain hazardous substances in electrical and electronic equipment). this product also has the following attributes: ? ? ? ? 15 h 12 br 4 0 2 ) free ? ? msl rating msl rating : level 1 test: 260c convection reflow standard: jedec standard ipc/jedec j - std - 020 contact information for the latest specifications, additional product in formation, worldwide sales and distribution locations, and information about triquint: web: www.triquint.com tel: +1.503.615.9000 email: info - sales@triquint.com fax: +1.503.615.8902 for technical questions and application information: email: sjcapplications.engineering@triquint.com important notice the information contained herein is bel ieved to be reliable. triquint makes no warranties regarding the information contained herein. triquint assumes no responsibility or liability whatsoever for any of the information contained herein. triquint assumes no responsibility or liability whatso ever for the use of the information contained herein. the information contained herein is provided "as is, where is" and with all faults, and the entire risk associated with such information is entirely with the user. all information contained herein is subject to change without notice. customers should obtain and verify the latest relevant information before placing orders for triquint products. the information contained herein or any use of such information does not grant, explicitly or implicitly, to any party any patent rights, licenses, or any other intellectual property rights, whether with regard to such information itself or anything described by such information. triquint products are not warranted or authorized for use as critical components in medical, life - saving, or life - sustaining applications, or other applications where a failure would reasonably be expected to cause severe personal injury or death.
|
