tpsmp13 thru tpsmp43a document number 88471 29-nov-04 vishay semiconductors www.vishay.com 1 do-220aa (smp) n ew p ro duct high power density surface mount automotive transient voltage suppressors major ratings and characteristics features ? very low profile - typical heigth of 1.0 mm ideal for automated placement unidirection only exclusive patented par oxide passivated chip construction excellent clamping capability low incremental surge resistance very fast response time meets msl level 1, per j-std-020c v (br) 13 v to 43 v p ppm 400 w i fsm 40 a t j max. 185 c aec-q 101 qualified typical applications protection for ics, drive transistors, signal lines of sen- sor units, and electronic units in consumer, computer, inductrial, and automotive applications. mechanical data case: do-220aa (smp) epoxy meets ul 94v-0 flammability rating terminals: matte tin plated (e3 suffix) leads, solder- able per j-std-002b and mil-std-750, method 2026 polarity: color band denotes the cathode end maximum ratings t a = 25 c, unless otherwise specified note: (1) non-repetitive current pulse, per fig.3 and derated above t a = 25c per fig.2 (2) mounted on p.c.b. with 5.0 x 5.0 mm copper pads attached to each terminal (3) pulse test: 300 s pulse width, 1% duty cycle parameter symbol value unit peak power dissipation with a 10/1000 s waveform (1)(2) fig.3 p ppm minimum 400 w peak power pulse current with a 10/1000 s waveform (1) fig.1 i ppm see table next page a peak forward surge current 10 ms single half sine-wave superimposed on rated load i fsm 40 a maximum instantaneous forward voltage at 25a (3) vf 2.5 v operating junction and storage temperature range t j, t stg -65 to +185 c
www.vishay.com 2 document number 88471 29-nov-04 tpsmp13 thru tpsmp43a vishay semiconductors electrical characteristics t a = 25 c, unless otherwise specified notes: (1) v (br) measured after i t applied for 300 s, i t = square wave pulse or equivalent (2) surge current waveform per fig.3 and derated per fig. 2 (3) all terms and symbols are consistant with ansi/ieee c62.35 devise type device marking code breakdown voltage v (br) (1) at i t v te s t current i t (ma) stand-off voltage v wm (volts) maximum reverse leakage at v wm i r (a) maximum reverse leakage at v wm t j = 150 c i d (a) maximum peak pulse surge current i ppm (note 2) (amps) maximum clamping voltage at i ppm v c (volts) maximum temperature coefficient of v (br) (%/c) min max tpsmp13 aup 11.7 14.3 1.0 10.5 1.0 5.0 21.1 19.0 0.081 TPSMP13A avp 12.4 13.7 1.0 11.1 1.0 5.0 22.0 18.2 0.081 tpsmp15 awp 13.5 16.3 1.0 12.1 1.0 5.0 18.2 22.0 0.084 tpsmp15a axp 14.3 15.8 1.0 12.8 1.0 5.0 18.9 21.2 0.084 tpsmp16 ayp 14.4 17.6 1.0 12.9 1.0 5.0 17.0 23.5 0.086 tpsmp16a azp 15.2 16.8 1.0 13.6 1.0 5.0 17.8 22.5 0.086 tpsmp18 bdp 16.2 19.8 1.0 14.5 1.0 5.0 15.1 26.5 0.088 tpsmp18a bep 17.1 18.9 1.0 15.3 1.0 5.0 15.9 25.5 0.088 tpsmp20 bfp 18.0 22.0 1.0 16.2 1.0 5.0 13.7 29.1 0.090 tpsmp20a bgp 19.0 21.0 1.0 17.1 1.0 5.0 14.4 27.7 0.090 tpsmp22 bhp 19.8 24.2 1.0 17.8 1.0 5.0 12.5 31.9 0.092 tpsmp22a bkp 20.9 23.1 1.0 18.8 1.0 5.0 13.1 30.6 0.092 tpsmp24 blp 21.6 26.4 1.0 19.4 1.0 5.0 11.5 34.7 0.094 tpsmp24a bmp 22.8 25.2 1.0 20.5 1.0 5.0 12.0 33.2 0.094 tpsmp27 bnp 24.3 29.7 1.0 21.8 1.0 5.0 10.2 39.1 0.100 tpsmp27a bpp 25.7 28.4 1.0 23.1 1.0 5.0 10.7 37.5 0.096 tpsmp30 bqp 27.0 33.0 1.0 24.3 1.0 5.0 9.2 43.5 0.097 tpsmp30a brp 28.5 31.5 1.0 25.6 1.0 5.0 9.7 41.4 0.097 tpsmp33 bsp 29.7 36.3 1.0 26.8 1.0 5.0 8.4 47.7 0.098 tpsmp33a btp 31.4 34.7 1.0 28.2 1.0 5.0 8.8 45.7 0.098 tpsmp36 bup 32.4 39.6 1.0 29.1 1.0 5.0 7.7 52.0 0.099 tpsmp36a bvp 34.2 37.8 1.0 30.8 1.0 5.0 8.0 49.9 0.099 tpsmp39 bwp 35.1 42.9 1.0 31.6 1.0 5.0 7.1 56.4 0.100 tpsmp39a bxp 37.1 41.0 1.0 33.3 1.0 5.0 7.4 53.9 0.100 tpsmp43 byp 38.7 47.3 1.0 34.8 1.0 5.0 6.5 61.9 0.101 tpsmp43a bzp 40.9 45.2 1.0 36.8 1.0 5.0 6.7 59.3 0.101
tpsmp13 thru tpsmp43a document number 88471 29-nov-04 vishay semiconductors www.vishay.com 3 ratings and characteristics curves (t a = 25 c unless otherwise specified) figure 1. peak pulse power rating curve figure 2. pulse derating curve figure 3. pulse waveform 0.1 1.0 10 100 0.1 s 1.0 s10 s 100 s 1.0ms 10ms p ppm, peak po w er (k w ) td, p u lse w idth, sec. t a = 25 c n on-repetiti v e p u lse w a v eform sho w n in fig. 3 tpsmp10 - tpsmp43a tpsmp6. 8 - tpsmp9.1a 0 25 50 75 100 0 50 100 150 200 peak p u lse po w er (p pp ) or c u rrent (i pp ) derating in percentage ( % ) t a , am b ient temperat u re ( c) 25 75 125 175 0 50 100 150 i ppm ? peak p u lse c u rrent, % i rsm t j = 25 c p u lse w idth (td) is defined as the point w here the peak c u rrent decays to 50 % of i ppm tr = 10 sec. peak v al u e i ppm half v al u e ? ipp i ppm 2 td 10/1000 sec. w a v eform as defined b y r.e.a. 0 1.0 2.0 3.0 4.0 t ? time (ms) figure 4. typical junction capacitance figure 5. maximum peak forward surge current 10 100 1000 10000 cj, j u nction capacitance (pf) 010 100 v (br) breakdo w n v oltage ( v ) t j = 25 c f = 1.0 mhz v sig = 50m v p-p meas u red at stand-off v oltage, v w m meas u re at zero bias 40 nu m b er of cycles at 50 hz i fsm, peak for w ard s u rge c u rrent (a) 10 1 10 100 20 30 15 25 35 0 5
www.vishay.com 4 document number 88471 29-nov-04 tpsmp13 thru tpsmp43a vishay semiconductors package dimensions in inches (millimeters) 0.000 (0.00) 0.012 (0.30) 0.013 (0.35) 0.004 (0.10) 0.018 (0.45) 0.006 (0.15) 0.045 (1.15) 0.033 (0.85) 0.036 (0.91) 0.024 (0.61) 0.016 (0.40 ) 0.032 (0.80 ) 0.053 (1.35) 0.041 (1.05) 0.012 (0.30) ref 0.105 (2.67) 0.025 (0.635) 0.100 (2.54) 0.030 (0.762) 0.050 (1.27) cathode band 0.142 (3.61) 0.126 (3.19) 0.158 (4.00) 0.146 (3.70) 0.086 (2.18) 0.074 (1.88) 0.087 (2.20) 0.103 (2.60) do-220aa (smp)
|
