mahe0.5a~mahe0.5m features low profile package ideal for automated placement glass passivated chip junctions ultrafast reverse recovery time low switching losses, high efficiency high forward surge capability high temperature soldering 260 /10 seconds at terminals component in accordance to rohs 2002/95/1 and weee 2002/96/ec major ratings and characteristics mechanical date case: jedec msma molded plastic body over glass passivated chip terminals: solder plated, solderable per j-std-002b and jesd22-b102d i f(av) 0.5 a v rrm 50 v to 1000 v i fsm 15 a t rr 50ns, 75ns v f 1.0 v, 1.3 v, 1.7 v polarity: laser band denotes cathode end maximum ratings & thermal characteristics (t a = 25 c unless otherwise noted) note 1: mounted on p.c.b. with 0.2 x 0.2? (5.0 x 5.0mm) copper pad areas. electrical characteristics (t a = 25 c unless otherwise noted) note 2: pulse test:300 s pulse width,1% duty cycle. operating junction and storage temperature range t j t stg maximum average forward rectified current i f(av) peak forward surge current 8.3 ms single half sine-wave superimposed on rated load i fsm thermal resistance from junction to lead (1) r jl maximum repetitive peak reverse voltage v rrm maximum rms voltage v rms maximum dc blocking voltage v dc t j max. 150 c mahe 0.5a mahe 0.5b mahe 0.5d mahe 0.5g items symbol mahe 0.5j mahe 0.5k mahe 0.5m unit 50 100 200 400 600 800 1000 v 35 70 140 280 420 560 700 v 50 100 200 400 600 800 1000 v 0.5 a 15 a 35 /w ?55 to +150 items test conditions symbol mahe0.5a~ mahe0.5d mahe0.5g mahe0.5j~ mahe0.5m a unit instantaneous forward voltage i f =0.5a (2) v f v 1.3 1.0 1.7 75 reverse current v r =v dc t j =25 t j =125 i r 5 100 50 ns typical junction capacitance 4.0v,1.0mhz c j 11 8 pf reverse recovery time i f = 0.5 a , i r = 1.0 a , i rr = 0.25 a t rr http://www.trr-jx.com surface mount ultra fast rectifiers
characteristic curves (t a =25 unless otherwise noted) http://www.trr-jx.com mahe0.5a~mahe0.5m surface mount ultra fast rectifiers
package outline notice product is intended for use in general electronics applications. product should be worked less than the ratings; if exceeded, may cause permanent damage.or introduce latent failure mechanisms. the absolute maximum ratings are rated values and must not be exceeded during operation. the following are the general derating methods you design a circuit with a device. i f(av) : we recommend that the worst case current be no greater than 80% . i fsm : this rating specifies the non-repetitive peak current. this is only applied for an abnormal operation, which the general during the lifespan of the device. t j : derate this rating when using a device in order to ensure high reliability. we recommend that the device be used at a t j of below 125c. trr is registered trademark of rising-sun technology. rising-sun te chnology reserves the right to make changes to any product i n this specification to improve reli ability,functional characterist ics,or design without notice. rising-sun technology does not assure any liability arising out of the applic ations or any product descr ibed in this specificat ion. rising-sun technology advises customers to obtain the latest vers ion of the device information before placing orders to verify that the required information is current. http://www.trr-jx.com mahe0.5a~mahe0.5m surface mount ultra fast rectifiers
|
