smart vision lights ? 2359 holton rd. ? muskegon, mi 49445 ?phone 231.722.1199 www.smartvisionlights.com the SW75 series features a stainless steel ip6 9k rated enclosure with sealed bolts and waterproof connector for applications in wash down and corrosive environments. the SW75 comes equipped with npn and pnp signal input for strobe and offers a 0-10 vdc analog intensity control as well as a manual intensity control potentiometer. six high current leds are mounted to an alumin um back plate of which is mounted to the stainless steel enclosure for extra heat dissipation ability. electrical input 24 vdc +/ - 5% current max. 400ma wattage max. 9.6w strobe input pnp ? +3vdc or greater to activate. npn ? gnd (<1vdc) to activate pnp line 3.7ma @ 3vdc 6.2ma @ 5vdc 12.6ma @ 10vdc 30.4ma @ 24 vdc npn line 22ma @ common (0vdc) continuous mode light will be in continuous mode by leaving signal on strobe input active potentiometer intensity control of 10% to 100% clockwise increases intensity analog intensity the output is adjustable from 10 - 100% of brightness by a 0 - 10 vdc signal connection 5 pin m12 connector ambient temp. - 20o - 50o c ( - 4o - 122o f) lifespan 100,000 hrs ip rating ip69k compliances ce and rohs weight ~710g iec 62471 rating see page 4 ? 9k standards ? ? ? ? ? ? ? s w 75 series washdown brick light product introduction product features product specifications free datasheet http://
6 p d u w 9 l v l r q / l j k w v ? + r o w r q 5 g ? 0 x v n h j r q 0 , ? 3 k r q h www.smartvisionlights.com if analog 0 - 10 vdc is not used to control light intensity; +vdc (24vdc) must be connected to analog input - jumper pin 5 to pin 1 pin wire color function signal 1 brown power +24 vdc 2 white npn strobe gnd for active on 3 blue ground gnd 4 black pnp strobe 4vdc to 30vdc for active on 5 green analog intensity control 0 - 10 vdc ce and rohs compliant s w 75 xxx x* product family: brick light s w 75 color : 470, 505, 530, 625, 850, 940 & whi (white) f ? part number key * lights come standard with narrow lenses 1 24v 2 npn 3 gnd 4 pnp 5 0 - 10v standard m12 mating cable color code: brown white blue black *gray (green/yellow) attention please note tha t the power requirements are up to 400 ma at 24vdc. failure to supply light with up to 400ma can result in non - repeatable lighting. contact smart vision lights for more information. ! lenses: w - wide l - line product number key warnings wiring configuration free datasheet http://
6 p d u w 9 l v l r q / l j k w v ? + r o w r q 5 g ? 0 x v n h j r q 0 , ? 3 k r q h www.smartvisionlights.com working distance pattern (80% - 100% measured intensity) mm (inches) mm (inches) .5m (19.7") p p a d 1m (39.4") p p a d 1.5m (59") p p a d typical output performance illumination (lux) distance = .5 meter 96 00 illumination measurement taken on white lights C 6500k working distance pattern (80% - 100% measured intensity) mm (inches) mm (inches) .5m (19.7") 210 p p a d 1m (39.4") 425 p p a d 1.5m (59") 6 p p a d typical output performance illumination (lux) distance = .5 meter 6300 illumination measurement taken on white lights C 6500k s w 75 - xxx s w 75 - xxx - w optical p erformance free datasheet http://
6 p d u w 9 l v l r q / l j k w v ? + r o w r q 5 g ? 0 x v n h j r q 0 , ? 3 k r q h www.smartvisionlights.com risk group 15m stainless steel cable available 5 pin m12 power input manual intensity control according to iec 62471:2006. full documentation upon request. notice exempt group : no photo biological hazard to eyes or skin even for continuous, unrestricted use. applicable for wavelengths: 625, 850, and 940. caution risk group 1 : possibly hazardous optical radiation emitted from this product. do not stare at operating lamp. may be harmful to eye. safe for most applications except prolonged exposures. applicable for wavelengths: 470, 505, 530, and whi. identification free datasheet http://
|
