unit of electro switch corp. ? electronic products 2010 yonkers road, raleigh, nc 27604 specifications electrical current and voltage rating: make and break resistive load 0.25 amp @ 28 vdc; 0.1 amp @ 125 vac. current carrying capacity: 6 amps. dielectric strength: 600 vac between current carrying parts and ground. contact resistance: average initial 5 milliohms. insulation resistance: in excess of 10,000 megohms. hardware: mounting nut and lockwasher are shipped assembled. solder lug - adjustable stops switches - 30 indexing - stops set @ 2 pos. vertical p.c. terminals - adjustable stops switches - 30 indexing - stops set @ 2 pos. specifications and ordering information mechanical materials and finishes: all parts utilize non-corrosive materials as standard. terminals and contacts: brass with silver plate as standard. insulation: diallyl phthalate. index: dual-ball, hill and valley. index life: 25,000 cycles minimum. index torque: switches have lowest practical torque consistent with crisp detenting and smooth, reliable operation. index angles: 30 standard, 60 , and 90 available. index stops: fixed standard, adjustable, or continuous available. stop strength: 0.9 nm minimum. standard part number c1 - series 21.97 mm wide 0.25 amp @ 28 vdc active poles/ no. of shorting non- fig. poles positions deck decks shorting * active poles/ no. of shorting non- fig. poles positions deck decks shorting * the c1 series is our smallest enclosed rotary switch, offering index angles of 30 , 60 , and 90 . standard designs utilize solder lug or vertical pc terminals and diallyl phthalate insulation. 01 02-12 1 1 c1d0112s - a c1d0112n - a ca 01 02-06 1 1 c1d0106s - va c1d0106n - va cb 02 02-12 1 2 c1d0212s - a c1d0212n - a ca 01 02-12 1 1 c1d0112s - va c1d0112n - va cc 02 02-06 2 1 c1d0206s - a c1d0206n - a ch 02 02-06 1 2 c1d0206s - va c1d0206n - va cb 03 02-12 1 3 c1d0312s - a c1d0312n - a ca 02 02-12 1 2 c1d0212s - va c1d0212n - va cc 03 02-04 3 1 c1d0304s - a c1d0304n - a ck 03 02-06 1 3 c1d0306s - va c1d0306n - va cb 04 02-06 2 2 c1d0406s - a c1d0406n - a ch 03 02-12 1 3 c1d0312s - va c1d0312n - va cc 06 02-04 3 2 c1d0604s - a c1d0604n - a ck 04 02-06 1 4 c1d0406s - va c1d0406n - va cb 06 02-06 2 3 c1d0606s - a c1d0606n - a ch 04 02-12 1 4 c1d0412s - va c1d0412n - va cc dimensions * figures are shown on page 55. c1d c1d solder lug construction v vertical p.c. construction 6 note: 1. add 5.08 for each additional deck. 2. 12 fixed position uses adjustable stop dimensions. c m e t r i c
unit of electro switch corp. ? electronic products 2010 yonkers road, raleigh, nc 27604 c1 d customers specified order number for standard options (specify) (specify) (specify) (specify) (specify) (specify) (specify) (specify) additional options additional options and ordering information c1 - series shaft , bushing , and flat options shaft as viewed with non-turn lug at 9 o'clock and shaft in extreme ccw position and strut bolts oriented vertically. stop pins adjustable stop mechanism u y w z 2 digit insulation total active contact series type poles positions type terminal index stop shaft/ shaft type angle type bushing flat c1 d - diallyl 01 - min. 12 - max @ 30 n - non- 06 - max @ 60 shorting 04 - max @ 90 s - shorting l - solder lug 30 f - fixed v - vert. p.c. 60 c - cont. 90 a - adj. see see r - rear p.c. 30 f - fixed chart chart 60 c - cont. "a" "b" 90 how to order additional options: custom switches are available. contact the factory with your complete specifications. printed circuit board terminal options 7 rear p.c. fixed stop construction p.c. brd. pattern r c m e t r i c
|