10G-KR datasheet 10gbase-kr/kr4 compliance, debug, and decode solution features & bene ts automates compliance measurements for ieee 802.3ap-2007 speci cations includes both a tekexpress ? automation solution (for compliance) and dpojet (for debug) automated test setup for measuring transmitter equalization levels generating 72 results, 12 results for each tap approximately 15 minutes to generate 120 results for 9 different measurements keithley rf switch support for four lanes of kr/kr4 signal acquisition and analysis support available using cost-effective sma cables p7520 trimode probe support for soldering to backplane kr directly provision for entering lter les to de-embed the effects of backplane traces and any other components in the signal pathway provides users with a tektronix floating license installa tion option summary and detail test reports with margin and statistical information aid analysis complete programmatic interface available; users can call 10G-KR functions using their automation scripts end-users can receive e-mail noti cation on measurement results and stay connected with their test setup design engineers can utilize many built-in reporting features such as appending the report, auto-incrementing the report, including user comments, etc. to tailor their reporting requirements performs automatic signal validation before performing tests and displays an error if the signal does not meet acceptable limits provides protocol decode to disassemble 10G-KR 64b/66b traf cwith time-correlated views of physical and protocol layer works equally well on live setup and stored waveforms applications ethernet 10G-KR transmitter testing for: device silicon valid ation system compliance and debug manufacturing test
datasheet the tektronix 10G-KR/kr4 compliance, debug, and decode solution software automates testing of 10gbase-kr/kr4 10 gigabit ethernet copper backpla ne based on the ieee 802.3ap speci cations. the tekexpress framework allows design and validation engineers to con gure their test setup, choose the measurements they want to run, and nally generate detailed test reports which help engineers make critical design and validation decisions. it also lets design engineers make use of the dpojet jitter and analysis framework to debug their products. for design and validatio n engineers working on kr4, the 10G-KR solution provides an option to use keithley rf switches and automates multiple-lane testing. option 10G-KR enables both an automation solution (for compliance) and dpojet (for debug). tekexpress 10G-KR measurement setup the new 10G-KR solution helps engineers to easily select measurements for ieee 802.3ap speci cation testing. simple and easy-to-use measurement setup helps engineer s perform all measurements with a single button click. automation options help engineers meet their compliance needs and generate detailed reports. user-de ned mode lets users make changes to the test limits and perform margin testing beyond compliance. user-de ned mode enables exible parameter control for characterization and margin analysis. the guided wizard prompts the user to send required patterns and calculate the measurements accordingly. the test report includes pass/fail summary, patterns used for testing, measured values of margins and limits, and waveforms and measurements used during the test process. 10G-KR dpo jet user interface. n1n0, prbs11, and prbs31-based measurement setup les. dpojet 10G-KR measurement setup all limits and measurement parameters are automatically con gured for the users. additionally, design engineers have the exibility to change selected measurements and measurement con gurations within dpojet. 10G-KR dpojet options provide a new standard-speci c ui. new additional measurements have been added including rise time, fall time, v p-p , jitter, speed, output waveform characteristics, etc. based on ieee 802.3ap speci cations. setup les are provided based on different signal types such as n1n0, prbs11, and prbs31. signal-speci csetup les allow design engineers to perform measurements on different signal types, letting them go into analysis and debug mode. 2 www.tektronix.com
10G-KR ? 10gbase-kr/kr4 compl iance, debug, and decode solution details of the ieee 802.3ap speci cation measurements covered in 10G-KR. transm itter output waveform requirements. measurement details 72.7.1.11 output waveform coef cient update and status ? 10gbase-kr requires the user to measure speci c regions of the waveform such as overshoot and de-emphasis levels to determine the transmitter output equalization levels. there are six taps and the state of the transmitter equalizer, and as a result the transmitter output waveform, is manipulated accor ding to the protocol de ned in 72.6.10 of ieee 802.3ap or through management. the changes in the transmitter output waveform resulting from coef cient update requests shall meet the requirements stated in table 72?7 of ieee 802.3ap. the coef cient update requests in table 72?7 of ieee 802.3ap are to be followed by a coef cient update equal to hold for all taps. the results shall be veri ed after the coef cient status for all taps is rep orted as not_updated. for any coef cient update, the magnitudes of the changes in v1, v2, and v3 shall be within 5 mv of each other. when suf cient increment or decrement updates have been applied to a given tap, it will reach a maximum or transmitter output waveform requirements related to coef cient update. transmitter output waveform requirements related to coef cient status. minimum limit governed by the coef cient range or by restrictions placed on minimum steady-state or maximum peak voltage, and the coef cient status is reported accordingly. the transmitter output waveform shall meet the requirements of table 72?8 of ieee 802.3ap for all of the limiting cases represented in the table. implementation of c(?1) or c(1) coef cient values greater than zero or less than the minimum de ned by rpre (min) and rpst (min) is optional. a coef cient may be disabled by rst asserting the preset control de ned in ieee 802.3 table 45?55 and 45.2.1.78, then manipulating the other coef cients as required by the test. this measurement, if done manually, is prone to human errors. measuring 104 results and keeping track of each result could be problematic and is not the best use of an engineer?s time. 10G-KR makes the job of an engineer easy by noting down all the values and tabulating them in a way which can be easily interpreted. 72.7.1.3 signaling speed ? measured using recommend ed signal prbs11. the 10gbase-kr signaling speed shall be 10.3125 100 ppm. 72.7.1.4 differential peak -peak output voltage (max) ?measuredusing recommended signal prbs11. 72.6 .5 differential peak-peak output voltage (max) with tx disabled ? measured when tx is disabled. the differential output voltage is constrained according to the transmitter output waveform requirements speci ed in 72.7.1.10 of ieee 802.3ap. for a 1010 pattern, the peak-peak differential output voltage shall be less than 1200 mv, regardless of equalization setting. the transmitter output voltage shall be less than 30 mv peak -peak when disabled. the differential output voltage test pattern shall consist of no fewer than eight symbols of alternating polarity. www.tektronix.com 3
datasheet 72.7.1.4 common-mode voltage limits ? measured using recommended signal prbs11. the common-mode voltage of sl and sl shall be between 0 v and 1.9 v with respect to signal ground. 72.7.1.7 transition time ? rise time and fall time measured using recommended signal n1n0 where 8 n 11 the rising and falling edge transition times shall be between 24 ps and 47 ps as measured at the 20% and 80% levels referenced to v2 and v5 as de ned in 72.7.1.11 of ieee 802.3ap. measurement is done using the square wave test pattern with no equalization and a run of at least eight consecutive ones and zeroes. 72.7.1.8 max output jitter (peak-peak) ? measured using recommended signal prbs11. jitter components to be measured: random jitter ? 0.15 ui peak-peak deterministic jitter ? 0.15 ui peak-peak duty cycle distortion ? 0.035 ui peak-peak total jitter ? 0.28 ui peak-peak for the purpose of jitter measurement, the effect of a single-pole high-pass lter with a 3 db point at 4 mhz is applied to the jitter. crossing times are de ned with respect to the midpoint (0 v) of the ac-coupled differential signal. equalization shall be off during jitter testing. transmit jitter test requirements are speci ed in 72.7.1.9 of ieee 802.3ap. the transmitter shall have a maximum total jitter of 0.28 ui peak-peak, compose d of a maximum deterministic component of 0.15 ui peak-peak and a maximum random component of 0.15 ui peak-peak. duty cycle distortion (dcd) is considered a component of deterministic jitter and shall not exceed 0.035 ui peak-peak. the peak-peak duty cycle distortion is de ned as the absolute value of the difference in the mean pulse width of a 1 pulse or the mean pulse width of a 0 pulse (as measured at the mean of the high- and low-voltage levels in a clock-like repeating 0101 bit user can change limits, use lter les, and go beyond compliance. sequence) and the nominal pulse width. jitter speci cations are speci ed for ber 10?12. 72.7.1.10 output waveform characteristics ? measured using recommended signal n1n0 where 8 n 11. the test pattern for the transmitter output waveform is the square wave test pattern de ned in 52.9.1. 2 of ieee 802.3, with a run of at least eight consecutive ones. the transmitter output waveform test is based on the voltages v1 through v6, dv2, and dv5, which shall be measured as shown in figure 72?12 of ieee 802.3ap. simpli ed instrument setup ? save time and resources setup an d test execution is simple with the 10G-KR solution. the oscilloscope acquisition and analysis are all controlled through the 10G-KR automation solution. the software?s graphical user interface (gui) provides an intuitive work ow for setup and testing. margin testing design characterization is supported beyond ieee 802.3ap speci cation compliance requirements for all measurements. qualify phy with exible control over test con gurations such as analysis windows and other parameters. user-de ned mode lets engineers make changes to the test limits and perform marginal testing beyond compliance. 4 www.tektronix.com
10G-KR ? 10gbase-kr/kr4 compl iance, debug, and decode solution report con guration menu ? the report con guration menu lets users con gure reports and it provides options such as auto-increment, appending, etc. de-embedding feature as data rates increase, high-speed serial technologies have introduced new test methodologies and requirements for compliance testing. as technologies such as 10gbase-kr increase in data rates, the eye is closed and diffe rent components such as sma cables can be de-embedded to get better results. 10G-KR provides an option to de-embed the signal using .flt les. one-butt on testing once the test bench is set up and the dut is properly connected, simply press th e run button to perform the selected test suite. the 10G-KR solution prompts the end-user to put the dut into different test modes by popping messages at regular intervals. automat ion support save and recall setup les in automation script, with an option to automate the comp lete test bench. tektronix end-users can call the 10G-KR application programmatically through ni labview, ni teststand?, or any other scripting language for controlling 10G-KR along with other instrumentation such as thermal chambers and power supplies. sma cables, probe, and keithley rf switch support design engineers who may want to solder the probe to the backplane copper lanes can do so because 10G-KR provides support for p7516, p7520, and p7520a trimode probes. engineers who want to make use of cost-effective sma cables can directly connect sma cables to their devices connec tion diagram for differential input. connection diagram for single-ended input. connection diagram using rf switch. and monitor the signals on the tektronix oscilloscopes. engineers working on four lanes of kr can make use of keithley rf switches to automate their complete setup. www.tektronix.com 5
datasheet ieee 802.3ap speci cations measurements covered on 10G-KR. prerecorded waveform prerecorded waveform support provides users with an option to use prerecorded waveforms when an oscilloscope is not available. this feature allows wav eforms to be shared across multiple locations and removes end-user dependency on using scopes all the time. pass/fail report 10G-KR report. a summary report in .mht (mhtml) format with pass/fail status is automatically generated after tests complete. the report includes test con guration details, waveform plots, and margin analysis to provide more insight in to your design. 6 www.tektronix.com
10G-KR ? 10gbase-kr/kr4 compl iance, debug, and decode solution 10gbase-kr custom decode feature 10G-KR custom decode provides protocol decoding to disassemble the 10gbase-kr ethernet 64b/66b traf c, including time-correlated views of physical and protocol layers. decode results are displayed as a waveform and an event-table, along with red ags on crc/ecc errors in the decoded data. you can view protocol decode along with time stamps on the decoded data in event-tables. 10G-KR custom decode features and values 10G-KR protocol decode solution offers several features to simplify validation of 64b/66b designs. key features that add value proposition to design engineers working on 10g base-kr products include: setup wizard for quick setup, con guration and test packet-level decoding of primitives, as well as link and transaction layers, helps capture abnormalities serial data analysis of 64b/66b bit streams decoding of scrambled and unscrambled symbols provides engineers two different views on the data ability to save symbol and packet data lists to csv les for of ine analysis packet decode details tab provides detailed information on packets: ? packet information ? channel information (live channel, math) ? listing index ? control symbols ? reserved-bit settings ? packet length quick search capability for speci c symbols provides a fast method to search on different areas of interest comprehensive search capability the 10G-KR packet content search function is very useful for isolating an event of interest. once you have captured an event and need to analyze the surrounding data, what do you do? in the past, you had to manually scroll through the wav eform data, counting and converting bits, to determine what caused the event. the 10G-KR protocol decoder search function speeds up event analysis by letting you enter criteria (such as serial packet content) to quickly look through the acquired data for speci c events. the search engine marks each occurrence in the data. you can then use the previous and next buttons on the instrument to rapidly navigate between marks. comprehensive search capability theresultstabshowsthelistofsearchhits. clickonaniteminthelistto go to the associated position on the waveform. 10G-KR decoder search results www.tektronix.com 7
datasheet ordering information 10G-KR 10gbase-kr/kr4 compliance and debug solution. to order alon g with oscilloscope oscilloscope option dpo/dsa/mso70000 10G-KR to upgrade a n existing oscilloscope oscilloscope option dpo/dsa/mso70000 dpo-up 10G-KR dpofl-10G-KR (floating license) dpoft-10G-KR (floating trial) recommended equipment product type models oscilloscopes dpo /dsa/mso71604c dpo/dsa/mso72004c dpo/dsa72504d dpo/dsa73304d software 10G-KR and dja* 1 accessories matched-pair sma cables (tca-sma connector) or p7516, p7520, p7520a trimode probes keithley switch for kr4 support ? s46 dc blocks model 5501a dc block picosecond * 1 prerequisite for 10G-KR. 8 www.tektronix.com
10G-KR ? 10gbase-kr/kr4 compl iance, debug, and decode solution www.tektronix.com 9
datasheet contact tektronix: asean / australa sia (65) 6356 3900 austria 00800 2255 4835* balkans, israel, south africa and other ise countries +41 52 675 3777 belgium 00800 22 55 4835* brazil +55(11)37597627 canada 1 800 833 9200 central east eu rope and the baltics +41526753777 central europe & greece +41 52 675 3777 denmark +4580881401 finland +41526 75 3777 france 00800 2255 4835* germany 00800 2255 4835* hong kong 400 8 20 5835 india 000 800 650 1835 italy 00800 2255 4835* japan 81 (3) 67 14 3010 luxembourg +41526753777 mexico, central/south america & caribbean 52 (55) 56 04 50 90 middle east, asia, and north africa +41 52 675 3777 the netherlands 00800 2255 4835* norway 800 16098 people?s rep ublic of china 400 820 5835 poland +41 52 675 3777 portugal 80 08 12370 republic of korea 001 800 8255 2835 russia & cis +7 (495) 7484900 south africa +41526753777 spain 00800 2255 4835* sweden 00800 2255 4835* switzerland 00800 2255 4835* taiwan 886 ( 2) 2722 9622 united kingdom & ireland 00800 2255 4835* usa 1 800 833 9200 * european toll-free number. if not accessible, call: +41 52 675 3777 updated 10 february 2011 for further information. tektronix maintains a comprehensive, constantly expanding collection of application notes, technical bri efs and other resources to help engineers working on the cutting edge of technology. please visit www.tektronix.com copyrigh t ? tektronix, inc. all rights reserved. tektroni x products are covered by u.s. and foreign patents, issued an d pending. information in this publication supersedes that in all previously published material. speci ca tion and price change privileges reserved. tektronix and tek are registered trademarks of tektroni x, inc. all other trade names referenced are the service marks, trademarks, or registered trademarks of their r espective companies. 21 jan 2013 61w-28213-1 www.tektronix.com
|
