lc-40/46/52/60le810un (1st edition) 5 ? 10 8.2.3 composite n358 signal/tuner adjustment 8.2.4 component 15k signal adjustment 8.2.5 component 33k signal adjustment 8.2.6 analog rgb signal adjustment adjustment point adjustment conditions adjustment procedure 1 setting n358 signal us-10ch ? send the n358 color bar (color saturation: 75%) signal to the video 2 video input. ? send the in-house signal (use us-10ch) to tuner. 2 automatic adjustment exe- cution point the cursor to [ n358 all adj(input2)] and press the [enter] key. the adjustment is complete when [ n358 all adj(input2) ok] is displayed. adjustment point adjustment conditions adjustment procedure 1 setting 480i signal ? send the 100% color bar signal to the video 1 component input. 2 automatic adjustment exe- cution point the cursor to [ comp15k adj(input1)] and press the [enter] key. the adjustment is complete when [ comp15k adj(input1) ok] is displayed. adjustment point adjustment conditions adjustment procedure 1 setting 1080i signal ? send the 100% color bar signal to the video 1 component input. 2 automatic adjustment exe- cution point the cursor to [ comp33k adj(input1)] and press the [enter] key. the adjustment is complete when [ comp33k adj(input1) ok] is displayed. adjustment point adjustment conditions adjustment procedure 1 setting signal: xga (1024x768) 60hz sync: hv separate ? send the 100% color bar signal to the video 4 analog rgb input. 2 automatic adjustment exe- cution point the cursor to [ analog rgb adj] and press the [enter] key. the adjustment is complete when [ a nalog rgb adj ok] is displayed. [video input signal] [in-house us-10ch] 100% white 100% white 0% black color saturation: 75% 100% white 0% black 480i 100% color bar color saturation: 100% 100% white 0% black 1080i 100% color bar color saturation: 100% 100% white 0% black xga (1024x768) 100% color bar free datasheet http:///
lc-40/46/52/60le810un (1st edition) 5 ? 11 8.2.7 tuner/v-chip adjustment adjustment point adjustment conditions adjustment procedure 1 setting ntsc rf signal us-7(air)ch ? send the ntsc signal to the rf antenna input. 2 automatic adjustment exe- cution point the cursor to [ tuner vchip test(*07ch)] and press the [enter] key. (* adjust the selected channel to the in-house signal.) the adjustment is ok when [ a-ok(***. **)/vm-ok] is displayed in green. (ng when a-ng/vm-ng is displayed in red.) it is ok when the deviation from the center frequency is 0.0625mhz or less. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 5 ? 12 9. white balance adjustment 9.1. white balance adjustment (for details about the adjustme nt procedure, refer to ?kameyama model integrated monitor wb adjustment specification v1.92?.) adjustment point adjustment conditions adjustment procedure 1 setting 1) set the unit to the following conditions. av mode: [dynamic] backlight: +16 active backlight: off aging time: min. 60 minutes 2) connect the unit with the white balance adjustment jig. 2 automatic adjustment exe- cution [command] process mode krsw0001 kkt10037 setting ky0f0000 0sds0001 sbsl0016 multi-point adjustment mode mset0011 point 6 lev60229 mg6g**** mg6b**** mg6r**** mg6y**** point 5 lev50173 mg5g**** mg5b**** mg5r**** mg5y**** point 4 lev40133 mg4g**** mg4b**** mg4r**** mg4y**** point 3 lev30116 mg3g**** mg3b**** mg3r**** mg3y**** point 2 lev20074 mg2g**** mg2b**** mg2r**** mg2y**** point 1 lev10045 mg1g**** mg1b**** mg1r**** mg1y**** writing mset0003 [adjustment procedure] 1) send the ?adjustment process? code using the remote control. 2) set the point 6 to the specified gradation, specify the strongest color as the fixed color, and adjust the rgb so that it becomes the standard value through negative adjustment. then compare the r and g values; based on the result, calculate the ye value in the following conditions. r > g: ye = g x 1.05 r g: ye = r x 1.05 * if the ye value exceeds the initial value (input gradation x 4), it is rounded to that value or less. 3) set the point 5 to the specified gradation, set the g correction value (692 x g value of point 6/916) (fractions rounded off) and the ye correction value (692 x ye value of point 6/916) (fractions rounded off), and adjust the rb so that it becomes the stan- dard value. 4) set the point 4 to the specified gradation, set the g correction value (532 x g value of point 6/916) (fractions rounded off) and the ye correction value (532 x ye value of point 6/916) (fractions rounded off), and adjust the rb so that it becomes the stan- dard value. 5) set the point 3 to the specified gradation, set the g correction value (464 x g value of point 6/916) (fractions rounded off) and the ye correction value (464 x ye value of point 6/916) (fractions rounded off), and adjust the rb so that it becomes the stan- dard value. 6) set the point 2 to the specified gradation, set the g correction value (296 x g value of point 6/916) (fractions rounded off) and the ye correction value (296 x ye value of point 6/916) (fractions rounded off), and adjust the rb pattern so that it becomes the standard value. 7) set the point 1 to the specified gradation, set the g correction value (180 x g value of point 6/916) (fractions rounded off) and the ye correction value (180 x ye value of point 6/916) (fractions rounded off), and adjust the rb so that it becomes the stan- dard value. 8) write the adjustment value by the mset0003 command and turn off the ac power. * rgb initial value of point 6: set gradation 916 * rgb initial value of points 1 to 5: g correction value of each point (at each point, make adjustment so that the remainder of the rgb adjustment value/ 4 is equal.) [adjustment value] * according to the ?standard settings? s ubmitted by the technical department [lc52le810un] le810 model teaching set free datasheet http:///
lc-40/46/52/60le810un (1st edition) 5 ? 13 10. key writing 10.1. edid writing (main pwb: qpwbxf452wjzz) 10.2. mmac address writing (main pwb: qpwbxf452wjzz) 1. refer to the production precautions. 10.3. netflix & wmdrm key writ ing (main pwb: qpwbxf452wjzz) 1. netflix key data is written in ic8401. the data cannot be copied nor run on different cpu. it can be written only in factory securely. therefore when key data is corrupted or lost or you replace main cpu, ic8001, or flash rom, ic8401, you have to replace main pw b. you can check if the key data is stored correctly by following means. ? process menu the key is displayed to [netflix esn] on the 1st page in the adjustment process menu. ? rs-232c 1. enter the process mode. 2. nfky???? : esn data is returned. adjustment point adjustment conditions adjustment procedure [adjustment standard value] measuring instrument: [minolta ca- 210] technical measuring instrument level reference value adjustm ent spec inspection spec point 6 916 x=0.272 0.0010 0.0020 y=0.277 point 5 692 x=0.272 0.0010 0.0020 y=0.277 point 4 532 x=0.272 0.0015 0.0030 y=0.277 point 3 464 x=0.272 0.0020 0.0040 y=0.277 point 2 296 x=0.272 0.0030 0.0060 y=0.277 point 1 180 x=0.272 0.004 0.0080 y=0.277 remarks setting conditions for inspection av mode: [dynamic] (reset) monochro: on active backlight: off aging time: min. 60 minutes adjustment point adjustment conditions adjustment procedure 1 hdmi edid writing (main pwb) process mode model discrimination check 1) enter the process mode. 2) point the cursor to [edid write ent] and press the [ent] key. the writing is complete when [edid write ok] is displayed. (if not written, hdmi does not function.) caution: perform the data writing after setting the model discrimi- nation. the data based on the model discrimination information is recorded in eeprom. 2 analog rgb edid writing (main pwb) inspection mode file version check 1) write the edid data for analog rgb into ic509 mounted on the main pwb using the checker. tl511 ??? i2c clock, tl508 ??? i2c data tl544 ??? 5v, tl507 ??? gnd tl585 ??? write protection (h: wp, l: write enable) 2) perform the data writing before making inspection using the checker. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 5 ? 14 11. factory setting after completing the factory setting, pull out the ac cord to complete the setting. caution: do not turn on the power after completing the factory setting. if the power is turned on , configure the factory setting again. 12. software version 1. main microcomputer 2. monitor microcomputer 3. edid data (analog rgb) 4. (reference: file name in the technical department) for analog rgb input3: ic509: edid_dsub15_fullhd_v6_256.bin 13. writing the inch and model name onto eeprom writing method 1. pull out the ac cord. 2. copy the application for writing inch/model name (hlnima01. usb) and model/inch file (40le810.mdl) to the usb memory. 3. hold down the power button and insert the ac cord. 4. release the power button after 5 seconds. 5. update starts. 6. pull out the ac cord. model/inch file ? 40le810.mdl ? 46le810.mdl ? 52le810.mdl ? 60le810.mdl * 32 inch is not necessary. note: when replacing the main pwb, make sure to perform the writing the inch and model name onto eeprom adjustment point adjustment conditions adjustment procedure 1 factory setting complete the setting by pulling out the ac cord. ? point the cursor to [industry init (+cause)], set to ?on? using [+]/[-] of the [vol] key, and press the [ent] key. the version confirmation screen appears on the green screen. it is completed when [suc- cess] is displayed at the top. (if error occurs, [error] is displayed on the red screen.) ? turn off the ac power. the following items are initialized when configuring the factory setting. 1) user set value 2) channel data (broadcasting frequency, etc.) 3) password setting value 4) operating time 5) standbycause 6) auto installation flag 7) v-chip block setting value 40le810 upgrade success the inch and model name are displayed. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 5 ? 15 [2] public mode setting procedure 1. how to start public mode ? there are the following 3 ways to get the public mode setup screen displayed. in the adjustment process mode, turn on ?public mode? 1) plug ac cord and turn on the tv. 2) after picture display ed, touch the ?power? key for 5seconds. note: picture will disappear when you touch the power key, but keep touching it. 3) when the center icon led blinks , release your finger from the power key. 4) next, touch the ?ch ( )? key and ?vol (+)? keys on the set at the same time. 5) when the center icon led turns on, release your finger form the keys. it?s same as from 1) to 3) 4) next, touch the ?input? key and ?ch ? keys on the set at the same time. 5) when the center icon led turns on, release your finger form the keys. 6) get the password input screen displayed. 7) the 3-digit password is now verified. the password [0] [2] [7] provides for the public mode screen. (this screen comes on with whatever adjustment process settings.) with any other passwo rds, the screen changes to the normal mode. 2. how to exit public mode there are the following ways to quit the public mode setup screen. ? turn off ?public mode? in the adjustment process mode. ( ) this way alone is not for quitting the se tup screen, but for quitting the mode itself. ? turn off the power with the ?power? key. ( ) ? select ?execute?. ( ) ... ?public mode? stays on in the adjustment process mode. ... the settings will be ba ck to the factory ones. 3. public mode setting values ? with the factory settings made, the public mode settings get initialized. (the adjustment process remains intact.) procedure ? the input starts with the leftmost digit. ? use the numeric keys [1] thru [9] and [0] keys on the remote controller. ? the other keys are not acceptable. ? with a numeric-key input, " _ " will change to " ? ". ? the input position will move one digit to the right. ? with all the 3 digits entered, the password will be verified. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 5 ? 16 4. public mode menu the guidance is not displayed on screen. setup procedure ? to move the cursor up and down, use the ?cursor up/down? key (remote controller) and ?ch ( )/( )? key (remote controller and set ). ? to change the settings, use the ?cursor right/left? key (remot e controller) and ?vol (+)/(?)? key (remote controller and set). ? to save new settings, keep the cursor at ?execut e? and use ?enter? key (remote controller and set). public mode power on fixed [variable ] maximum volume [ 60 ] volume fixed [variable ] volume fixed level [ 20 ] rc button [respond ] panel button [respond ] menu button [respond ] av position fixed [variable ] on screen display [yes ] input mode start [normal ] input mode fixed [variable ] loud speaker [on ] rc_path_through [off ] 232c powon [disable ] public mode [off ] reset execute free datasheet http:///
lc-40/46/52/60le810un (1st edition) 5 ? 17 5. on setting items * ?ez-setup? discussed below indicates ?ez-setup after the first power-on?. 1) power on fixed 2) maximum volume 3) volume fixed 4) volume fixed level 5) rc button selection selection between ?vari able? and ?fixed? (loop provided) default ? (variable) explanation in ?fixed? setting, the power-off by the power key of the unit is invalidated and the image is kept being received. the power can be turned off by stopping the power supply from ac. limit in setting refer to the ?power-on fixed? sheet. exception none remarks ? in ?variable? setting, the power operation is in wait for 1 sec. and then turned off when the main power switch is off. selection adjustment from 0 to 60 (no loop) default 60 explanation sound volume can not be adjusted higher than the preset value. limit in setting ? when the sound volume is set lower than 59, only figures are displayed and the sound volume bar is not displayed. ? the maximum sound volume for on-timer (wake up timer) is limited also to the preset value. exception remarks ? when the sound volume is set higher than the max setting by the adjusting process, the sound volume control operation is prohibited for turn-up and the sound volume should be turned down to max in this state. selection selection between ?variable?, ?fixed?, ?acon (ac ctrl)? and ?ac/rcon (ac/rc ctrl)? (loop provided) default variable explanation ? fixed: fixed at the level adjusted for a fixed volume. ? ac ctrl: start-up at the level specified for a fixed volume at acon. ? ac/rc ctrl: start-up at the level specified for a fixed volume at start. limit in setting ? the sound volume for the on-timer (wake up timer) is fixed also without display of menu. besides, the setting is made impossible. (basically, the menu is not displayed.) ? the following keys become invalid: ? sound volume up/down (vol +/?) [for both remote control and the unit] ? mute (mute) exception ? in the item ?volume? of adjustment process, the s ound volume can be set freely irrespective of this setting. remarks ? as for sound volume fixing and sound volume max level, the sound volume fixing has priority. ? once the sound volume has been changed by adjustment process, it should be set back to the sound volume preset by sound volume fixing level when the adjustment process ends. selection adjustment from 1 to 60 (no loop) default 20 explanation the sound volume to be fi xed by ?volume fixed? is determined. limit in setting none exception none remarks setting is valid only when ?vol ume fixed? is selected for ?fixed?. selection selection between ?respond?, ?no respond? and ?limited? (loop provided) default respond explanation making the remo te controller settings. ? at the ?no respond? setting, the remote controller keys are disabled. its power key (reception/standby key) is disabled too. ? at the ?limited? setting, some channel-related keys alone are oper ative. all the other remote controller keys (power, volume / , channel / , light control (brightness sensor), broadc ast select) are inoperative. limit in setting in ?no respond? setting, all the keys (i ncluding the power key) are not accepted. exception ? adjustment process, inspection process and hote l only keys are valid irrespective of setting. ? all the keys can be used in adjustment process, inspection mode and hotel m enu irrespective of setting. remarks free datasheet http:///
lc-40/46/52/60le810un (1st edition) 5 ? 18 6) panel button 7) menu button 8) on screen display 9) input mode start selection selection between ?respond? and ?no respond? (loop provided) default respond explanation all the operations by keys (except the power key) of the unit can be invalidated. limit in setting exception ? adjustment process, inspection mode and hotel m enu mode can be started irrespective of setting. ? all the keys can be used in adjustment process, inspection mode and hotel m enu irrespective of setting. remarks selection selection between ?respond? and ?no respond? (loop provided) default respond explanation in ?no respond? setting, the menu operation by the menu key of the remote control and the menu key of the unit are i nvali- dated. limit in setting exception ? adjustment process, inspection mode and hotel m enu mode can be started irrespective of setting. ? all the keys can be used in adjustment process, inspection mode and hotel m enu irrespective of setting. remarks selection selection between ?yes?, ?no? (loop provided) default yes explanation ? at the ?no? setting, the following items are not displayed on screen: register, setting, adjustment menu, channel call and vol - ume bar. on the wide-screen models, an input selection is imm ediately made because the menu is not displayed. ? at the ?limited? setting, some items cannot be displayed on screen. on the japan-destined models, the channel ca ll ?message? alone cannot be displayed. (this is because the channel call mes- sage may be confused with a message being sent from the hotel.) on the north america-destined models, the osd works the same as at the ?no? setting. limit in setting ? keys falling under any of the following items become invalid. appearance of screen changes and the sound changes. personal functions which are hard to restore. screen display, menu, off-timer, on-timer, av mode, screen size switching, clock setting , treble emphasis, audio only, sound changeover, language, closed caption others ? simple input switching is generated. those which are rest ored soon after leaving as they are and may be requested for change by customer are not prohibited. brightness sensor (backlight) and pic. flip exception ? such a caution which is displayed independently is disp layed as it is. non-responding signal caution remarks ? when cc has already been on, closed caption is displayed. selection selection between ?normal?, ?air ( )?, ?input 1/2/ 3?, ?pc?, ?hdmi 1/2/3/4/5?, ?dvi? (loop provided) default normal explanation in power-on, the input source to be started or channel can be set. (in standard mode, the operation follows the last memory.) about options ? all the input sources in the model are made selectable. ? in tv mode, the channel to be set follows the last memory and t he content of the last memory is included in the notation by options. ex.) air (2), cable (98.1) etc. limit in setting ? the display of channel setting menu and t he channel setting operation are prohibited. exception remarks ? in setting at ?normal?, the setting of ?input mode fixed? is changed to ?variable? and selection should be prohibited. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 5 ? 19 10)input mode fixed 11)rc_path_through 12)av position fixed 13)loud speaker (on/off) 14)232c powon selection selection between ?variable?, ?fixed?, ?acon (ac ctrl)? and ?ac/rcon (ac/rc ctrl)? (loop provided) default ? (variable) explanation ? at the ?fixed? setting, the tv set gets started with the settings of ?input mode start?, and then any other channels and input s are not accepted. ? at the ?acon (ac ctrl)? setting, the tv set gets started with the settings of ?input mode start? under ac control. ? at the ?ac/rcon (ac/rc ctrl)? setting, the tv set gets started with the settings of ?input mode start? under either control. limit in setting ? with the execution of hotel mode, the input source is forced to change to that set by ?input mode start? and the channel switching and input switching are prohibited thereafter. ? on-timer's (wake-up timer) channel items are not displayed or the operation is prohibited. (basically, they are not displayed. ) ? the following keys are invalidated. ch / , direct tuning button, flashback, input however, the keys (input switching and ch / keys) of the unit for menu operation remain valid. exception none remarks ? in the following case, setting is c ancelled and mode is changed to ?variable?. when the setting of ?input mode start? is set to ?normal?. selection selection between ?off?, ?on: tv rce? and ?on: tv rcd? (loop provided) default off explanation function to feed the remote controll er-received signal to pin 9 (open) on the rs232c. limit in setting none exception none remarks none selection selection between ?vari able? and ?fixed? (loop provided) default variable explanation in case of ?fixed? setting, ? menu ?picture? and ?audio? setting c an't be changed like ?dynamic (fixed)?. ? when ?av mode? key is pressed, tv just displays current av mode (cannot be changed.). limit in setting none exception none remarks ? when receiving with av position key, opc, dolby key and other direct audio select keys, the current display stays on and no setting can be changed. ? even by initializing personal information, the hotel-mode settings are kept intact. in this way, the av positions, video and audio adjustment settings are not initialized. selection selection between ?on? and ?off? (loop provided) default on explanation if ?off? is selected, tv stops speaker output even without headphone connected. limit in setting none exception none remarks ? press the volume up/down key, and the mute icon appears for 4 seconds. ? the mute key and audio-related keys are displayed with caution. ? usually, the headphones and monito r audio outputs can be adjustable. selection selection between ?disable? and ?enable? (loop provided) default disable explanation in the standby mode, the power-on by the 232c command is enabled or disabled. limit in setting none exception none remarks none free datasheet http:///
lc-40/46/52/60le810un (1st edition) 5 ? 20 15)public mode (on/off) selection selection between ?on? and ?off? (loop provided) default off explanation in case of ?on?, public mode settings are effected. limit in setting none exception none remarks the public-mode settings are operable only when this item is set at on. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 1 LC-40LE810UN service manual chapter 6. troubleshooting table [1] troubleshooting table no video (1) composite: no external input video [input-2] is input-2 selected on the input select menu screen? yes no select input-2 on the input select menu screen for the right input signal. is there the composite signal input at pin (ae29) of ic3302 (cpu)? yes no check the line between pin (8) of j507 and pin (ae29) of ic3302. are the lvds signal outputs at the lvds 1st channel and 2nd channel of ic3302? lvds_tx_0_data0_p/n (c14/d14), lvds_tx_0_data1_p/n (c15/d15), lvds_tx_0_data2_p/n (c16/d16), lvds_tx_0_data3_p/n (c18/d18), lvds_tx_0_data4_p/n (c19/d19), lvds_tx_0_clk_p/n (c17/d17), lvds_tx_1_data0_p/n (a14/b14), lvds_tx_1_data1_p/n (a15/b15), lvds_tx_1_data2_p/n (a16/b16), lvds_tx_1_data3_p/n (a18/b18), lvds_tx_1_data4_p/n (a19/b19), lvds_tx_1_clk_p/n (a17/b17). no check ic3302 and its peripheral circuits. (ic3501/ic3502, etc.) yes check the panel module. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 2 no video (2) component: no external input video [input-1] is input-1 selected on the input select menu screen? is the input-select for the input signal? yes no select input-1 on the input select menu screen for the right input signal. does the comp1_plug detection function? check the line between pin (4) of input terminal (j506) and pin (d30) of ic3302 (cpu). are there the component video signal inputs at pins (aj21) (y)/ (aj22) (pb) and (ah22) (pr) of ic3302 (cpu)? yes no check the line between the input terminals of j506 and ic3302. j508 pin (5) (y) pin (6) (pb) pin (7) (pr) ic3302 pin (aj21) pin (aj22) pin (ah22) are the lvds signal outputs at the lvds 1st channel and 2nd channel of ic3302? lvds_tx_0_data0_p/n (c14/d14), lvds_tx_0_data1_p/n (c15/d15), lvds_tx_0_data2_p/n (c16/d16), lvds_tx_0_data3_p/n (c18/d18), lvds_tx_0_data4_p/n (c19/d19), lvds_tx_0_clk_p/n (c17/d17), lvds_tx_1_data0_p/n (a14/b14), lvds_tx_1_data1_p/n (a15/b15), lvds_tx_1_data2_p/n (a16/b16), lvds_tx_1_data3_p/n (a18/b18), lvds_tx_1_data4_p/n (a19/b19), lvds_tx_1_clk_p/n (a17/b17). no check ic3302 and its peripheral circuits. (ic3501/ic3502, etc.) yes check the panel module. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 3 no video (3) no video at uhf/vhf broadcast signal reception no video at digital broadcast signal reception is the specified tv signal select ed on the input select menu screen? is there the analog video signal output (video) at pin (15) of tuner (tu1102)? are there the video signal outputs (if_p/n) at the pins (9) and (10) of tuner (tu1102)? yes no yes no check tu1102 and its peripheral circuits (tun_sda: pin6 of tu1102 tun_scl: pin7 of tu1102, etc.). check tu1102 and its peripheral circuits (tun_sda: pin6 of tu1102 tun_scl: pin7 of tu1102, etc.). is there the analog video signal input at pin (ad29) of ic3302 (cpu)? are there the video signal inputs at pin (aa29) and (ab29) of ic3302 (cpu)? yes no yes no check the line between ic3302 and tu1102, and their peripheral circuits. check the line between ic3302 and tu1102, and their peripheral circuits (c1129/c1130, etc.). are the lvds signal outputs at the lvds 1st channel and 2nd channel of ic3302? lvds_tx_0_data0_p/n (c14/d14), lvds_tx_0_data1_p/n (c15/d15), lvds_tx_0_data2_p/n (c16/d16), lvds_tx_0_data3_p/n (c18/d18), lvds_tx_0_data4_p/n (c19/d19), lvds_tx_0_clk_p/n (c17/d17), lvds_tx_1_data0_p/n (a14/b14), lvds_tx_1_data1_p/n (a15/b15), lvds_tx_1_data2_p/n (a16/b16), lvds_tx_1_data3_p/n (a18/b18), lvds_tx_1_data4_p/n (a19/b19), lvds_tx_1_clk_p/n (a17/b17). no check ic3302 and its peripheral circuits. (ic3501/ic3502, etc.) yes check the panel module. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 4 no video (4) pc: no external input video [input-3] is input-3 selected on the input select menu screen? yes no select input-3 on the input select menu screen for the right input signal. is ic509 (eeprom) accessed by i2c, with pc connected, to read the ddc_i2c scl/sda data? check the ddc line and its peripheral circuits. (ic509 and its peripherals). are there the video signal inputs at pins (ak16) (g), (ah15) (b) and (ak17) (r) of ic3302 (cpu)? are there the vsync/hsync signal inputs at pins (aj14) and (ak14) of ic3302? yes no check the line between sc501 and ic3302. are the lvds signal outputs at the lvds 1st channel and 2nd channel of ic3302? lvds_tx_0_data0_p/n (c14/d14), lvds_tx_0_data1_p/n (c15/d15), lvds_tx_0_data2_p/n (c16/d16), lvds_tx_0_data3_p/n (c18/d18), lvds_tx_0_data4_p/n (c19/d19), lvds_tx_0_clk_p/n (c17/d17), lvds_tx_1_data0_p/n (a14/b14), lvds_tx_1_data1_p/n (a15/b15), lvds_tx_1_data2_p/n (a16/b16), lvds_tx_1_data3_p/n (a18/b18), lvds_tx_1_data4_p/n (a19/b19), lvds_tx_1_clk_p/n (a17/b17). yes no check ic3302 and its peripheral circuits. (ic3501/ic3502, etc.) check the panel module. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 5
lc-40/46/52/60le810un (1st edition) 6 ? 6
lc-40/46/52/60le810un (1st edition) 6 ? 7 no audio (1) input-1 no audio. input-2 no audio. is input-1 selected on the input select menu screen? is input-2 selected on the input select menu screen? yes no yes no refer to ?: no external input video [input-1]?. refer to ?: no external input video [input-2]?. is the audio output selected for ?variable? on the menu screen? is the audio output selected for ?variable? on the menu screen? yes no yes no set the audio output to ?fixed?. set the audio output to ?fixed?. does the audio signal come from pi ns (4) (l) and (3) (r) of input terminal (j507) to pins (u29)(l) and (u28) (r) of ic3302 (cpu)? does the audio signal come from pi ns (4) (l) and (1) (r) of input terminal (j505) to pins (r28) (l) and (t26) (r) of ic3302 (cpu)? yes no yes no check the line between j507 and ic3302. check the line between j505 and ic3302. does the digital audio signal come from pins (f28/f30/g28) (aubck/aulrck/aosdata0) of ic3302 (cpu) to pin (8/9/7) (sp_bclk/sp_lrclk/sp_data) of ic2701 (audio dsp)? yes no check the line between ic3302 and ic2701, and their peripheral circuits. ? about the l/r speakers. does the digital audio signal come from pins (47/43/44/45) of ic2701 (audio dsp) to pin (5/8/7/6) of ic2703 (amp for l/r)? ? about the subwoofer speaker. does the digital audio signal come from pins (47/43/44/46) of ic2701 (audio dsp) to pin (5/8/7/6) of ic2702 (amp for sw)? no check ic2701 and its peripheral circuits. (x2701, etc.). yes ? about the l/r speakers. is the audio output from ic2703 as specified? ? about the subwoofer speaker. is the audio output from ic2702 as specified? no ? about the l/r speakers. check ic2703 and its peripheral circuits. ? about the subwoofer speaker. check ic2702 and its peripheral circuits. yes ? about the l/r speakers. check the connector (p2701) l/r speakers and their peripheral cir- cuits. ? about the subwoofer speaker. check the connector (p2702), subwoofer speaker and their periph- eral. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 8 no audio (2) [pc analog audio input] input-3 no audio. [hdmi analog audio input] input-4 no audio. is input-3 selected on the input select menu screen? is input-4 selected on the input select menu screen? yes no yes no refer to ?: no external input video [input-3]?. re fer to ?: no external input video [input-4]?. is the audio output selected for ?variable? on the menu screen? is the audio output selected for ?variable? on the menu screen? yes no yes no set the audio output to ?fixed?. set the audio output to ?fixed?. is the ?pc input? - ?audio select for ?video + audio? on the menu screen? is the ?pc input? - ?audio select? selected for ?hdmi + analog? on the menu screen? yes no yes no set the ?pc input? - ?analog select? to ?video + audio?. set the ?pc input? - ?analog select? to ?hdmi + analog. does the digital audio signal come from pins (f28/f30/g28) (aubck/aulrck/aosdata0) of ic3302 (cpu) to pin (8/9/7) (sp_bclk/sp_lrclk/sp_data) of ic2701 (audio dsp)? yes no check the line between ic3302 and ic2701, and their peripheral circuits. ? about the l/r speakers. does the digital audio signal come from pins (47/43/44/45) of ic2701 (audio dsp) to pin (5/8/7/6) of ic2703 (amp for l/r)? ? about the subwoofer speaker. does the digital audio signal come from pins (47/43/44/46) of ic2701 (audio dsp) to pin (5/8/7/6) of ic2702 (amp for sw)? no check ic2701 and its peripheral circuits. (x2701, etc.). yes ? about the l/r speakers. is the audio output from ic2703 as specified? ? about the subwoofer speaker. is the audio output from ic2702 as specified? no ? about the l/r speakers. check ic2703 and its peripheral circuits. ? about the subwoofer speaker. check ic2702 and its peripheral circuits. yes ? about the l/r speakers. check the connector (p2701) l/r speakers and their peripheral cir- cuits. ? about the subwoofer speaker. check the connector (p2702), subwoo fer speaker and their periph- eral. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 9 no audio (3) no audio at uhf/vhf broadcast signal reception. no audio at digital broadcast signal reception. is tv selected on the input select menu screen? is tv selected on the input select menu screen? yes no yes no refer to ?no video at uhf/vhf broadcast signal reception?. refer to ?no video at digital broadcast signal reception?. is the audio output selected for ?variable? on the menu screen? if no video appears, refer to ?no video at digital broadcast sig nal reception?. yes no set the audio output to ?fixed?. is the audio output selected for ?variable? on the menu screen? yes no set the audio output to ?fixed?. is there the sif signal output at pin (14) of tuner (tu1102)? yes no check the tuner (tu1102) and its peripheral cir- cuits. (i2c line: tuner_scl/tuner_sda, etc.) does the sif signal come from pin (14) of tuner (tu1102) to pin (ab27) of ic3302 (cpu)? yes no check the line between tu1102 and ic3302, and their peripheral circuits (q1101, q1102, etc.). does the digital audio signal come from pins (f28/f30/g28) (aubck/aulrck/aosdata0) of ic3302 (cpu) to pin (8/9/7) (sp_bclk/sp_lrclk/sp_data) of ic2701 (audio dsp)? yes no check the line between ic3302 and ic2701, and their peripheral circuits. ? about the l/r speakers. does the digital audio signal come from pins (47/43/44/45) of ic2701 (audio dsp) to pin (5/8/7/6) of ic2703 (amp for l/r)? ? about the subwoofer speaker. does the digital audio signal come from pins (47/43/44/46) of ic2701 (audio dsp) to pin (5/8/7/6) of ic2702 (amp for sw)? no check ic2701 and its peripheral circuits. (x2701, etc.). yes ? about the l/r speakers. is the audio output from ic2703 as specified? ? about the subwoofer speaker. is the audio output from ic2702 as specified? no ? about the l/r speakers. check ic2703 and its peripheral circuits. ? about the subwoofer speaker. check ic2702 and its peripheral circuits. yes ? about the l/r speakers. check the connector (p2701) l/r speakers and their peripheral cir- cuits. ? about the subwoofer speaker. check the connector (p2702), subwoo fer speaker and their periph- eral. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 10 no audio (4) input-4 no audio (hdmi connected) input-5 no audio (hdmi connected) input-6 no audio (hdmi connected) input-7 no audio (hdmi connected) [input-4 input] is input-4 selected on the input select menu screen? [input-5 input] is input-5 selected on the input select menu screen? [input-6 input] is input-6 selected on the input select menu screen? [input-7 input] is input-7 selected on the input select menu screen? yes no refer to ?: no external input video [input-4/5/6/7]?. [input-4 input] if no video appears, refer to ?no external input video (hdmi) [input-4]?. [input-5 input] if no video appears, refer to ?no external input video (hdmi) [input-5]?. [input-6 input] if no video appears, refer to ?no external input video (hdmi) [input-6]?. [input-7 input] if no video appears, refer to ?no external input video (hdmi) [input-7]?. is the audio output selected for ?variable? on the menu screen? yes no set the audio output to ?fixed?. does the digital audio signal come from pins (f28/f30/g28) (aubck/aulrck/aosdata0) of ic3302 (cpu) to pin (8/9/7) (sp_bclk/sp_lrclk/sp_data) of ic2701 (audio dsp)? yes no check the line between ic3302 and ic2701, and their peripheral circuits. ? about the l/r speakers. does the digital audio signal come from pins (47/43/44/45) of ic2701 (audio dsp) to pin (5/8/7/6) of ic2703 (amp for l/r)? ? about the subwoofer speaker. does the digital audio signal come from pins (47/43/44/46) of ic2701 (audio dsp) to pin (5/8/7/6) of ic2702 (amp for sw)? no check ic2701 and its peripheral circuits. (x2701, etc.). yes ? about the l/r speakers. is the audio output from ic2703 as specified? ? about the subwoofer speaker. is the audio output from ic2702 as specified? no ? about the l/r speakers. check ic2703 and its peripheral circuits. ? about the subwoofer speaker. check ic2702 and its peripheral circuits. yes ? about the l/r speakers. check the connector (p2701) l/r speakers and their periph- eral circuits. ? about the subwoofer speaker. check the connector (p2702), subwoofer speaker and their peripheral. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 11 no audio signal at digital audio output terminal (analog sound heard) no input-4/5/6/7 (hdmi) audio. no audio at digital broadcast signal reception. if no video appears, refer to ?no external input video (hdmi) [input-4/5/6/7]?. if no video appears, refer to ?no vi deo at digital broadcast signal reception?. is there the spdif signal output (opt _out) at pin (j28) of ic3302 (cpu)? yes no check the ic3302 and its peripheral circuits. is there the spdif signal (opt_out) input at pin (2) of ic503 (spdif buffer & spdif-mute)? yes no check the line between ic3302 and ic503. is there the mute signal input at pin (7) of ic503? (usual: high, mute: low) yes no check the mute_a_all and spdif-mute signals, and their peripheral cir- cuits (q505, d530, etc.). is there the spdif signal input at pin (1) of d520 (optical output)? yes no check the speakers and the optical cable. check d520 and its peripheral circuits. no optical output under the following conditions as per hdmi requirements. * audio contents protected. * audio frequency beyond 48khz. * audio bit length beyond 16bits. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 12 no monitor audio output is the audio output from the monitor set at ?variable? or ?fixed? on the menu screen? yes no check ic3302 (cpu) and its peripheral circuits. are there the audio signal outputs at pins (m28) (hp/moni_l) and (m27) (hp/moni_r) of ic3302 (cpu)? yes no check ic3302 (cpu) and its peripheral circuits. does the audio signal come from pins (m 28) (hp/moni_l) and (m27) (hp/moni_r) of ic3302 to pins (2) (l) and (3) (r) of j504? yes no check the line between ic3302 and j504 and their peripheral circuits. check the mute_a_au and hp/moni_mute lines and its peripheral circuits (q506, d527, etc.). check the connector (j504) and their peri pheral circuits, and speakers and the cable. no connect network does the signal come to 1pin of lan-jack j9501? (see fig-1, fig-2) yes check the interface device and peripheral circuits. (power-led of hub, link-led of hub) no does the signal come to 12pin of ic9501? (see fig-2) (ic9501: ksz8041t) yes check the line between j9501 and ic9501. check the lan-jack j9501. no does the 3.3vdc come to vdda_3.3/vddio_3.3 of ic9501? does the 2.5vdc come to vdd_1.8/vdda_1.8 of ic9501? no check the power-circuits of d3.3v. check 7pin (v1.8_out) of ic9501. yes does the clock signal come to 15pin of ic9501? (25mhz, 3.3v) no check the line between x9501 and ic9501. check the crystal x9501. (sca219wj) yes check ic9501 and its peripheral circuits. lan-jack j9501 fig-1 1pin fig-2 free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 13 if it is not an error of power supply/led driver, it is start-up in the lamp error disregard mode. do you start? yes does all led of one line are not lighting? yes no it doesn't light in 1 piece. all led boards including led th at doesn't light are exchanged. tp1 of led board on the power supply side is confirmed. does the voltage hang? yes no harness exchange is the led board connected with cn2? yes no tp1 of the next led board connec ted with cn2 is confirmed. does the voltage hang? even if the short-circuit conne ctor is exchanged, do not you light? yes no yes no the next led board is seen. led board exchange. the end. if it is not an error of power supply/led driver, it is start-up in the lamp error disregard mode. do you start? no is connected connector (la1) with t he first high led board of the power supply board removed and do it start? yes no all led boards and the harness connected with la1 are exchanged. is connected connector (la2) with the led board se cond on the power supply board removed and do it start? yes no all led boards and the harness connected with la2 are exchanged. is connected connector (la3) with the led board thir d on the power supply board removed and do it start? yes no all led boards and the harness connected with la3 are exchanged. all led boards are exchanged. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 14 [2] led flashing specificatio n at the time of an er ror (center icon led used) 1. display method ? since only the center icon led can be used, slow flashing and fast flashing are combined. ? refer to table 1. ? the start from the detail display. (no outline display) ? after recovering from an error, if the same error cannot be generated again, refer to monitor err cause on the process screen. ? during version upgrade, the brightness of the flashing led changes smoothly. ? when completing version upgrade, the brightness of the led changes in a staircase pattern. 2. led flashing method error flashing
lc-40/46/52/60le810un (1st edition) 6 ? 15 table 1. concrete flashing pattern *2: they depend on the system. power supply error is defined from product to product. *3: for details, refer to error standby cause on the adjustment process screen. *4: if the boot section is abnormal, ther e is no flashing (f lashing impossible). 3. new method item outline display detail display cause slow flashing fast flashing slow flashing fast flashing inverter/lamp sys- tem failure flashes once none flashes onc e flashes once lamp error power pwb failure (power failure, etc.) flashes twice none flashes twic e flashes once power supply error 1 (*2) ac_det error flashes twice power supply error 2 (*2) ur+13v error flashes 3 times power supply error 3 (*2) d3.3v error flashes 5 times panel power supply error main pwb failure (communication failure, etc.) flashes 3 times none flashes 3 times fla shes once initial communication error flashes twice start-up confirmation communication error flashes 3 times regular communication error flashes 5 times other communication error others flashes 4 times none flashes 4 times flashes once temperature error flashes twice sync error flashes 3 times notification from the main microcomputer (*3) verup executing flashes smoo thly none ? ? version upgrading verup succeeded flashes in a stair- case pattern none ? ? version upgrade succeeded verup failed none flashes continu- ously ? ? version upgrade failed rom data failure none flashes continu- ously ? ? start-up after failing version upgrade (*4) error flashing center icon press the [menu] key on the remote control. center icon center icon center icon flashing during verup flashing when completing verup 400ms 1600ms 400ms 300ms 1600ms 100ms 500ms 500ms 1000ms 400ms 400ms 1600ms 1000ms 1000ms 1000ms note: the north american models have no flashing pattern of slow flashing only. the detail display is presented by combining slow flashing free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 16 led flashing timing chart at the time of an error 1) slow flashing note 2) inverter/lamp failure details (flashes slowly once and flashes fast) note 3) power failure details (flashes slowly twice and flashes fast) note error type center icon led operation pins are monitor microcomputer pins. inverter/ lamp failure flashes slowly once h: on l: off refer to ?inverter/lamp failur e details?. flashes slowly and fast by pressing the [menu] key on the remote con- trol (refer to 2 below). power failure flashes slowly twice h: on l: off refer to ?power failure details?. flashes slowly and fast by pressing the [menu] key on the remote control (refer to 3 below). main cpu to main cpu communication failure flashes slowly 3 times h: on l: off refer to ?communication failur e details?. flashes slowly and fast by pressing the [menu] key on the remote con- trol (refer to 4 below). communication line failure or main cpu communication failure. check debug statements for the main cpu. others flashes slowly 4 times h: on l: off refer to ?other failure details?. flashes slowly and fast by pressing the [menu] key on the remote control (refer to 5 below). error type center icon led operation pins are monitor microcomputer pins unless other- wise specified. lamp failure flashes fast once h: on l: off err_pnl(40pin): hi failure. confirmed after 8 consecu- tive detections at 64msec intervals (detected only when the backlight is on). note that after five detection counts, the lamp cannot be activated except in the monitor process. accumulated counts are cleared to 0 by the setting in the process a. error type center icon led operation pins are monitor microcomputer pins unless other- wise specified. ps_on ac_det failure flashes fast once h: on l: off ac_det(72pin) failure (l). if error is detected during start-up or operation, the power is turned on again by interrupt (instantaneous blackout processing). sm_pow main 13v failure flashes fast twice h: on l: off det_13v(38pin) failure (l). main 13v is not applied. if error is detected during start-up or operation, the power is turned on again by polling. d_pow digital 3.3v failure flashes fast 3 times h: on l: off det_d3v3(36pin) failure (l). digital 3.3v is not applied. if error is detected during start-up or operation, the power is turned on again by polling. panel_pow panel 12v failure flashes fast 5 times h: on l: off det_pnl12v(35pin) failure (l). panel power is not applied. detection is started after turning on the panel power and receiving command; the power is turned off by polling. 100ms 400ms 1.6sec free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 17 4) communication failure details (flashes slowly 3 times and flashes fast) note 5) other failure details (flashes slowly 4 times and flashes fast) note error type center icon led operation basically, debug print logs are analyzed or commu- nication logs are analyzed by a bus monitor. initial communica- tion reception failure flashes fast once h: on l: off initial communication from the main cpu is not received. (request for the monitor model no. is not received.) communication line failure or main cpu start-up fail- ure start-up confirma- tion reception failure flashes fast twice h: on l: off start-up reason confirmation from the main cpu cannot be received. (start-up communication until start-up rea- son notification command is not received.) main cpu start-up failur e or monitor microcomputer reception failure regular communica- tion failure flashes fast 3 times h: on l: off regular communication that is performed at 1 second intervals in the normal operation is interrupted. main cpu operation failure or monitor microcom- puter reception failure other communica- tion failure flashes fast 5 times h: on l: off when a request (pm_req=h) is sent from the main microcomputer, the request command is not output from the main cpu, etc. main cpu operation failure or monitor microcom- puter reception failure error type center icon led operation pins are monitor microcomputer pins unless other- wise specified. monitor temperature failure flashes fast once h: on l: off if the panel temperature is 60 c or more for 15 seconds or more in a row, caution appears on the osd (flashes in red in the lower right screen). if the panel temperature is 60 c or more for 25 seconds or more in a row, error standby is activated. (monitor max temp on page 23 of the process a: change of temperature failure ad value): thermistor main failure flashes fast 3 times h: on l: off main microcomputer detection error (cpu temperature error, etc.) the details are displayed on page 1 of the process a of the main microcomputer. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 ? 18 4. monitor err stby table outline: communication/power failure detected by the monitor micr ocomputer is stored on eeprom, and the last 4 abnormal states c an be confirmed in the process mode a. location: page 1 of the process mode a: monitor err cause ?0? if there is no error. it is cleared to 0 on the last page of the process mode a. display error description 02 start-up communication error 2 initial communi cation from the main cpu is not received. 03 start-up communication error 3 only th e initial communication is received. 04 start-up communication error 4 until panel information request reception 05 start-up communication error 5 until initialization completion reception 06 start-up communication error 6 until version notifi cation transmission 07 start-up communication error 7 until star t-up information notification transmission 08 start-up communication error 8 until start-up information response reception 09 start-up communication error 9 until time-out setting reception 0a communication error a req time-out 0b communication error b restart time-out duri ng the beginning of time acquisition start-up 0c communication error c ending sequence time-out 0d communication error d preset start-up time-out during completion 0e communication error e download, start-up time-out 0f communication error f time acquisition time-out 11 communication error h regular communication time-out 16 panel-related error lamp failure 1a other error 2 monitor temperature failure 1d power supply error 1 ps_on (ac_det) failure 1e power supply error 2 d_pow (det_13v) failure 1f power supply error 3 d_pow (det_d3v3) failure 21 power supply error 5 panel power failure 23 other error 3 error standby request from the main cpu free datasheet http:///
lc-40/46/52/60le810un (1st edition) 7 ? 1 LC-40LE810UN service manual chapter 7. major ic informations [1] major ic informations 1. major ic informations 1.1. ic1504 (vhisii9287+-1q) this ic is 4 input and 1 output hdmi port processor. it integrated tmds receiver and transmitter cores capable of receiving and transmitting at 2.25gbps. (supports video resolution s up to 1080p, 60hz, 12bit.) the equalizer circuits to adapt long cable are integrated in this ic. edid and ddc support for 4 hdmi/dvi ports and 1 vga port.(this ic includes 256-byte nvram and 256-byte sram for each port(5 tot al).) 1.2. ic2002 (rh-ixc786wjn4q) the monitor microprocessor is intended to communicate wi th the main microprocessor and to operate the system. it also controls power of the entire system. 1.3. ic2702, ic2703 (vhiyda164qz-1y) the class-d type digital audio pow er amplifier yda164qz gives maximum continuous output of 10 w/ch or woofer output 15w. 1.4. ic3302 (rh-ixd058wjqzq) this lsi is full high-definition 1080p digital tv system-on-a-chip. it combines a cable/terrestrial 64/256-qa m and 8-vsb receiver, a transport processor, a digital audio processor, a high definit ion (hd) mpeg video decoder, 2d graphics processing, digital processing of analog video and audio, analog video digitizer and dac functions, stereo high-fidelity audio dacs, hdmi receivers for 1080p 60 inputs, a 625-mhz processor, and a peripheral control unit provid ing a variety of television control functions. the cable/terrestrial receiver directly samples a tuner output with an analog-to-digital converter (adc). the lsi digitally resample and demodulates the signal with re covered clock and carrier timing, filters and equalizes the data, and passes soft deci- sions to an atsc/a74 and itu-t j.83 annex b-compatible decoder. it has an mpeg-2 digital video broadcasting (dvb)-compliant trans port processor with advanced sect ion filtering capability, dvb descrambler, and an mpeg-2 (mp@hl profile) video decoder. audio support includes a btsc and a dolby ac3/mpeg-2 layer 1, 2, audio decoder. the lsi provides analog and digital audio/video outputs. a spdif output and a pair of analog outputs (l-r ) are provided via the integrated audio dacs. the ntsc analog video decoder is supported by its own motion adaptive deinterlacing and 3d comb filtering, including 1080i dein terlacing. the lsi includes advanced 2d graphics processing. one transport stream input is included. the lsi incorporates a complete arm11-based microprocessor subsyst em including caches with bridging to memory and a local bus, where external peripherals can be attached. integrated peripherals include two usb 2.0, thr ee uarts, counter/timers and gpio controllers. in this tine, h264 decode/vc-i decode/secure boot function are added to this ic. 1.5. ic3501/ic3502 (rh-ixc754wjqzq) these are 1g bit (64m x 16bit) ddr2-1066 synchronous dram. 1.6. ic8401 (rh-ixc894wjqzq) the 512m-bit nand flash memory devic e stores the main cpu program. 1.7. ic8455 (vhir24064as-1y) this is 64k-bit eeprom device including the user setting. 1.8. ic506 (vhim3221eip-1y) this ic is a high speed, single-channel rs -232 transceiver interface device that op erates from a single 3.3v power supply. the device provides the electrical inte rface between an asynchronous communication controller and the serial-port connector. this device operate at data signaling rates up to 460kbit/s. all rs-232(tout and rin) and cmos (tin and rout) inputs and output s are protected against electrostatic discharge (up to +/- 15 kv esd protection). 1.9. ic9501(vhiksz8041t-1y) this ic is a single supply 10bas e-t/100base-tx physical layer tr ansceiver, which provides mii/rm ii/smii interfaces to transmit and receive data. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 7 ? 2 1.10. ic2701 (v hiyss951vz-1y) audio dsp (yss951vz) has digital audio adjustment function (for example, peq, bass/treble, balance, bass enhancer, etc.) and ad justs tvs audio quality. free datasheet http:///
lc-40/46/52/60le810un (1st edition) 8 ? 1 LC-40LE810UN service manual chapter 8. overall wiring/system block diagram [1] overall wiring diagram 1 23 10 9 7 6 5 4 8 j a b c d e f g h i 13 11 19 18 16 15 14 12 17 overall wiring diagram a ra ay 12 e m b l e m u n i t d u n t k f 4 9 3 f m 0 1 a lw ay 180 nxp 180 141 lch: r r s p - z a 4 5 6 w j z z rch: r r s p - z a 4 5 6 w j z z m a i n u n i t d u n t k f 4 5 2 f m * * digital audio output mdk ddr ::?:::?::?:? a ra ay 1 15 1 5 a sp ay pc audio in a lw ay 1 41 a pd ay 1 12 1 9 a lb ay a pd ay p o w e r u n i t 4 0 " b r u n t k a 6 8 2 w j q z 4 6 " b r u n t k a 6 8 3 w j q z 5 2 " b r u n t k a 6 9 3 w j q z 6 0 " b r u n t k a 6 8 4 w j q z 1 12 a lb ay a pl ay 14 14 a pl ay 13 a ac ay tuner y c c c r rs232c hdmi usb2 hdmi hdmi hdmi analog rgb rj45 usb1 vlr hp/audio out micro sd 1 9 1 4 a pl ay a lw ay 1 41 clover 12 a sb ay woofer 40/46" b r s p - z a 4 5 8 w j z z 52/60" b r s p - z a 4 5 7 w j z z l c d _ c t l u n i t ( a s i c v e r ) * * * * l c d _ c t l u n i t ( f p g a v e r . ) r u n t k 4 4 3 7 * * c c a rl ay 1 3 l o g o u n i t d u n t k f 4 9 3 f m 0 2 a ra ay r / c u n i t d u n t k f 4 9 4 f m 0 1 a rk ay t o u c h k e y u n i t 8 1 0 : r u n t k a 6 9 2 w j q z 8 2 0 : r u n t k a 6 9 0 w j q z 1 8 1 5 1 3 a rl ay 1 4 1 5 module a l1 ay a l2 ay free datasheet http:///
lc-40/46/52/60le810un (1st edition) 8 ? 2 [2] system block diagram 1 23 10 9 7 6 5 4 8 j a b c d e f g h i 13 11 19 18 16 15 14 12 17 system block diagram i c 3 3 0 2 m t 5 3 9 1 w ( f h d ) h . 2 6 4 / v c - 1 digital av decode & main cpu n_cpu_rst p d p o w e r ? p9601(12pin) spi_flash /nand flash lvds out usb_0 d_if in-/+ audio in dtv/spdif i2c_1 reset uart-0 rgb in(ak17) ddc_i2c_1 hdmi_1 cvbs i2c_0 m a i n sif thermister ps_on bu5v ac_det i c 2 0 0 2 m 1 6 c / 6 4 a ixc786wj sub mcu power circuit main 8v 5.6v 5v d3.3v d1.8v d1.26v d1.05v lamp_err i/o i/o ac_det i/o thermo a/d a/d int0 cvbs if_agc i n p u t 1 ur13v backup bu+3.3v i/o i/o s c 8 4 5 2 program update connector i c 2 7 0 3 sp amp(2ch) yda164 pe hp/moni_l/r i2s(sdata/lrck/sclk) disclete mute pc/hdmi_lr r g b / h d m i a u d i o ( m i n i p l u g ) a s p ay p 2 7 0 1 ext-sp s p e a k e r i/o o p t i c a l o u t opt_out mute 27.000mhz x 3 3 0 2 x ' t a l x2002 x t a l 20mhz i n p u t 4 i n p u t 3 i n p u t 3 r f i n t u 1 1 0 1 a n a l o g / d i g i t a l s i t u n e r +5v uart_5391to232c,uart_232cto5391 stb tuner_i2c (400khz 3.3v) j 3 3 0 1 u s b i c 5 0 6 rs232c txrx m3221eip r s - 2 3 2 c +3.3v n o . 9 p i n r c p a s s t h r o u g h det_13v,det_5v i c 5 0 9 eeprom l b p 9 6 0 2 (9pin ) i c 8 4 5 5 eeprom 64kbit +3.3v sif i n p u t 2 h d m i 1 i n p u t 5 i n p u t 3 / 4 d - s u b r g b audio out i c 3 5 0 1 d d r 2 ( 1 0 6 6 m ) 1 g b i t uart-2 i2c_0 c o m p o n e n t / l r c v b s / l r ( m i n i p l u g ) cvbs_in cvbs_in_l/r d_if_in-/+ comp_in_l/r d+5.6v ps_on i c 3 3 0 1 l i n e r e g . s170b50u i/o i/o ofl1 pwm_0 i c 8 4 0 1 n a n d f l a s h 1gbit +3.3v +8.0v +3.3v +1.8v +1.25v +1.05v l w p 2 6 0 1 (41p ) rxd,txd uart p 2 0 0 1 bu+3.3v i c 2 0 0 8 g a t e 7wh126fu ucom_rst rs_buf_cnt rxd,txd i c 2 0 0 1 r e s e t bu+3.3v cnvss pm_req, cboots n_sreset n_sreset i2c rgb hv(ak14,aj14) i c 1 5 0 4 h d m i - s w sii9287 i2c_0_400khz ddc_3 hdmi_3 ddc_2 hdmi_2 +3.3v a u d i o o u t ( m i n i p l u g ) cec_0 tuner_i2c pwm_1 cec_0 ofl2 i2c_2 i c 3 5 0 2 d d r 2 ( 1 0 6 6 m ) 1 g b i t pnl_pow i/o s13v stb_cpu i/o uart component comp_y/pb/pr if_agc h d m i 2 h d m i 3 h d m i 4 i n p u t 6 ddc_0 hdmi_0 ddc_1 hdmi_1 i c 5 0 3 o p t o u t t 7 s e t 0 8 i c 2 6 0 1 s p l i t e r hc2g66dp i2c_0 (400khz) from cpu ondd8 :* 15 onda6 :* i c 9 5 0 1 e t h e r n e t b u s i n t e r f a c e n_tun_rst +3.3v sdiocmd/sdioclk sdi0 :* 3 i c 2 7 0 1 d s p (yss951) i2c_0 (400khz) i c 2 7 0 2 woofer amp (0.1ch) yda164 sdata0 sdata1 lrck/sclk/mclk a s p ay p 2 7 0 2 ext-sp w o o f e r +3.3v +1.8v +13v +13v det_sync x2001 x t a l 32.768khz mii j 3 3 0 2 u s b i c 3 3 0 4 l i n e r e g . s170b50u usb_1 j 9 5 0 1 e t h e r n e t uart-1 +5v +5v key_pow,key_scl,key_sda bu+3.3v r / c o p c r a p2003(15p) m e n u / p o w e r i n p u t / c h a n n e l v o l u m e t o u c h k e y r c i c o n r i (2p) r l p2006 (3p) ill ctrl1 ill ctrl2 d+5v rc,opc eeprom_scl/sda i c 2 0 0 4 e e p r o m 2kbit bu+3.3v wp t r key_rst pwm pnl_pow ac_det pc/hdmi_lr cvbs_in_l/r comp_in_l/r pc_vsync/hsync pc_r/g/b pc_vsync/hsync pc_r/g/b opt_out hp/moni_l/r sif (400khz 3.3v) r a (5p) k y (2p) bu+3.3v d+3.3v 24.576mhz x 2 7 0 1 x ' t a l i c 9 6 0 1 s p l i t e r hc2g66dp von o_s_set frame det_pnl12v b_statu pnl_w pnl_rom_e pnl_e o n l y l e 8 2 0 u l o g o r l (3p) connector for software write /emulator line free datasheet http:///
parts guide parts marked with " " are important for maintaining the safety of the set. be sure to replace these parts with specified ones for maintaini ng the safety and perf ormance of the set. this document has been published to be used for after sales service only. the contents are subject to change without notice. lc-40/46/52/60le810un (1st edition) partsguide [1] printed wiring board assemblies [2] lcd panel [3] cabinet and mechanical parts (LC-40LE810UN) [4] cabinet and mechanical parts (lc-46le810un) [5] cabinet and mechanical parts (lc-52le810un) [6] cabinet and mechanical parts (lc-60le810un) [7] supplied accessories [8] packing parts (LC-40LE810UN) (not replacement item) [9] packing parts (lc-46le810un) (not replacement item) [10] packing parts (lc-52le810un) (not replacement item) [11] packing parts (lc-60le810un) (not replacement item) [12] service jigs (use for servicing) contents no. s30e840le810u lcd color television LC-40LE810UN lc-46le810un lc-52le810un lc-60le810un models free datasheet http:///
lc-40/46/52/60le810un (1st edition) 2 no. parts code price rank new mark part delivery description [1] printed wiring board assemblies n dkeymf452fm01 bm n x main unit n duntkf493fm01 n x icon unit n duntkf494fm01 n x r/c, led unit n runtka692wjqz as n x key unit n runtka682wjqz bp n x power/led drive unit (LC-40LE810UN) n runtka683wjqz bq n x power/led drive unit (lc-46le810un) n runtka693wjqz n x power/led drive unit (lc-52le810un) n runtka684wjqz bs n x power/led drive unit (lc-60le810un) n runtka692wjqz as n x touch sensor unit n runtk4437tpzz cb n x lcd control unit (LC-40LE810UN) n runtk4437tpza cb n x lcd control unit (lc-46le810un) n runtk4437tpzb cb n x lcd control unit (lc-52le810un) n runtk4437tpzc cb n x lcd control unit (lc-60le810un) n runtk4462tpzz bd n x led pwb unit (LC-40LE810UN), x4 n runtk4461tpzz be n x led pwb unit (lc-46le810un), x4 n runtk4460tpzz bf n x led pwb unit (lc-52le810un), x4 n runtk4458tpzz bh n x led pwb unit (lc-60le810un), x4 n runtk4459tpzz bb n x led pwb unit (lc-60le810un), x4 [2] lcd panel n r1lk400d3lwf2z n x 40" lcd panel module unit (lk400d3lwf2z) n r1lk460d3lwa2z n x 46" lcd panel module unit (lk460d3lwa2z) n r1lk520d3lwa2z n x 52" lcd panel module unit (lk520d3lwa2z) n r1lk600d3lw2bz n x 60" lcd panel module unit (lk600d3lw2bz) free datasheet http:///
lc-40/46/52/60le810un (1st edition) 3 [3] cabinet and mechanical parts (LC-40LE810UN) 36 34 8 37 14 14 4 34 28 21 16 14 6 14 35 33 43 45-3 34 44 45 44 5 31 31 30 15 12 7 27 27 9 27 11 10 27 14 27 27 27 32 32 19 27 9 13 40 41 40 41 13 27 27 27 1 2-2 2-1 2-11 2-9 2-12 2-3 2-6 2-4 2-13 2-10 2-13 2-5 1-2 20 2 20 17 22 3 42 26 18 24 23 17 25 27 27 27 27 38 29 c a b a k power/led drive unit icon unit touch sensor unit r/c, led unit h b j f g e 40" lcd panel module c a g f n m g f j k e k h k m n a main unit j d e b g f h d e b free datasheet http:///
lc-40/46/52/60le810un (1st edition) 4 no. parts code price rank new mark part delivery description [3] cabinet and mechanical parts (LC-40LE810UN) 1 ccabac527wj31 bs n x front cabinet ass'y 1-2 hdecqb442wj3a aa n x r/c decoration cover 2 ccabbb693we01 bl n x rear cabinet ass'y 2-1 gcabbb693wjsa bf n x rear cabinet 2-2 hindpd877wjsa af n x terminal label s 2-3 hindpd700wjsa ad n x terminal label b 2-4 pspahc152wj3z aa n x spacer 2-5 pspazc461wjzz ac n x spacer a 2-6 pzetka545wjkz ax n x insulator 2-9 pspahc159wjzz aa n x 300x10x0.5 himeron 2-10 pspahc160wjzz ab n x 170x10x0.5 himeron 2-11 pspahc166wjzz ab n x 445x8x0.5 himeron, x2 2-12 pspahc167wjzz ab n x 555x8x0.5 himeron, x2 2-13 pspahc168wjzz ab n x 565x8x0.5 himeron, x2 ! 3 qaccda074wjpz ag n x ac cord 4 lhldka011wjkz ab n x ac cord band 5 gcovad699wj3a ac n x ac cord cover 6 gcovad696wj3a ae n x stand cover 7 langkc695wjfw ad n x lcd fixing metal angle b-r 8 hindpd718wjsa ab n x model label 9 langkc689wjm1 ae n x vesa angle, x2 10 langkc694wjfw ad n x lcd fixing metal angle b-l 11 langkc696wjfw ad n x lcd fixing metal angle t-l 12 cangkc697wj01 n x lcd fixing metal angle t-r ass'y 12-1 langkc697wjfw ad n x lcd fixing metal angle t-r 12-2 pspahc165wjzz aa n x himeron 13 lhldwa175wjuz ac j holder, x3 14 lhldwa298wjka ad n j holder, x5 15 pzetka544wjkz av n x insulator 16 cangkc699wj31 ar n x stand angle ass'y 16-1 langkc699wjfw aq n x stand angle 16-2 not available - n x spacer, x2 17 lhldza587wjkz ac j holder, x6 18 gcovad734wj00 af n x terminal cover s 19 gcovad735wj00 ae n x terminal cover b 20 nsftza362wjfw aa n x shaft, x4 21 rsp-za458wjzz ax n x speaker (sub woofer) 22 qcnw-k548wjqz ae n x connecting cord (pd:pow-main) 23 qcnw-k550wjqz ad n x connecting cord (pl:pow-lcd_ctl) 24 qcnw-k552wjqz ae n x connecting cord (lb:pow-main) 25 qcnw-k553wjqz af n x connecting cord (sb:main-woofer) 26 qcnw-k576wjqz ap n x connecting cord (lw:main-lcd_ctl) 27 xbps730p06ws0 aa j screw, x37 (for chassis, pwb) 28 lx-bza364wjf7 aa n x screw, x4 (for sub woofer) 29 qcnw-k551wjqz aq n x connecting cord (ra:man-en/ky/rc) 30 qcnw-k554wjqz ag n x connecting cord (sp:man-sp(l/r)) 31 rsp-za456wjzz au n x speaker, x2 (l/r) 32 xbps730p10ws0 aa j screw, x3 (for lcd) 33 lx-bza170wjf9 aa n x screw, x4 34 xbps830p08js0 ab j screw, x13 (for rear cabinet) 35 xbps830p14js0 aa n x screw (for terminal) 36 xebs940p10000 ab j screw, x4 (for speaker) 37 tlabnb037wjzz ab n x serial label (back) 38 tlabnc391wjzz - n x serial label (side) 40 pspaga889wjkz ad n x spacer coner-top, x2 41 pspaga891wjkz ac n x spacer coner-bottm, x2 42 pzetka562wjkz ac n x ac barrier 43 cdai-a653wj01 be n x stand base ass'y 44 cangkc707wj01 at n x support ass'y 45 cx-bza363wj01 ad n x stand screw ass'y 45-3 xbbs840p08000 aa n x screw free datasheet http:///
lc-40/46/52/60le810un (1st edition) 5 [4] cabinet and mechanical parts (lc-46le810un) 2-11 2-7 2-6 2-11 2-10 2-8 2-4 2-9 45 40 46 9 2 4 46 42 2-2 2-3 2-1 2-5 44 43 5 39 50 51-3 46 26 26 33 35 19 25 22 24 25 23 34 34 22 41 41 37 20 49 17 34 17 21 18 34 21 6 34 21 30 28 27 31 32 29 8 1 3 51 36 1-2 20 34 12 34 20 11 34 34 10 37 38 41 15 16 7 34 34 34 34 34 36 20 20 20 34 14 13 34 47 c a b a a l e g f 46" lcd panel module c h k j j main unit h d e b j k h a j h g r/c, led unit touch sensor unit d icon unit e b l j power/led drive unit g f b f k h g f e 48 free datasheet http:///
lc-40/46/52/60le810un (1st edition) 6 no. parts code price rank new mark part delivery description [4] cabinet and mechanical parts (lc-46le810un) 1 ccabac528wj31 bs n x front cabinet ass'y 1-2 hdecqb442wj3a aa n x r/c decoration cover 2 ccabbb694we01 bn n x rear cabinet ass'y 2-1 not available - n x rear cabinet 2-2 hindpd877wjsa af n x terminal label s 2-3 hindpd700wjsa ad n x terminal label b 2-4 pspahc152wj3z aa n x spacer 2-5 pspazc461wjzz ac n x spacer 1 2-6 pzetka539wjkz az n x insulator 2-7 pspahc159wjzz aa n x 170x10x0.5 himeron 2-8 pspahc160wjzz ab n x 300x10x0.5 himeron 2-9 pspahc169wjzz ab n x 510x8x0.5 himeron, x2 2-10 pspahc170wjzz ab n x 630x8x0.5 himeron 2-11 pspahc171wjzz ab n x 385x8x0.5 himeron, x2 ! 3 qaccda074wjpz ag n x ac cord 4 lhldka011wjkz ab n x ac cord band 5 gcovad699wj3a ac n x ac cord cover 6 gcovad697wj3a af n x stand cover 7 langkc695wjfw ad n x lcd fixing metal angle b-r 8 lhldwa176wjuz ac n j holder, x2 9 hindpd719wjsa ab n x model label 10 langkc694wjfw ad n x lcd fixing metal angle b-l 11 langkc696wjfw ad n x lcd fixing metal angle t-l 12 cangkc697wj01 n x lcd fixing metal angle t-r ass'y 12-1 langkc697wjfw ad n x lcd fixing metal angle t-r 12-2 pspahc165wjzz aa n x himeron 13 langkc698wjfw ab n x lcd fixing metal angle b-ma 14 langkc810wjfw ac n x lcd fixing metal angle b-mb 15 pmlt-a632wjzz ac n x absorber 16 pclica014wjkz aa n x clip, x2 17 qearza186wjzz ad n x ground part, x2 18 cangkc700wj31 ar n x stand angle ass'y 18-1 langkc700wjfw aq n x stand angle 18-2 not available - n x spacer, x2 19 rsp-za458wjzz ax n x speaker (sub woofer) 20 lhldwa175wjuz ac j holder, x7 21 lhldwa289wjkz ac j holder, x3 22 lhldza587wjkz ac j holder, x6 23 gcovad734wj00 af n x terminal cover s 24 gcovad735wj00 ae n x terminal cover b 25 nsftza362wjfw aa n x shaft, x4 26 rsp-za456wjzz au n x speaker, x2 (l/r) 27 qcnw-k548wjqz ae n x connecting cord (pd:pow-main) 28 qcnw-k550wjqz ad n x connecting cord (pl:pow-lcd_ctl) 29 qcnw-k552wjqz ae n x connecting cord (pl:pow-lcd_ctl) 30 qcnw-k570wjqz ae n x connecting cord (sb:main-woofer) 31 qcnw-k577wjqz aq n x connecting cord (lw:main-lcd_ctl) 32 qcnw-k572wjqz aq n x connecting cord (ra:man-em/ky/rc) 33 qcnw-k559wjqz ag n x connecting cord (sp:man-sp(l/r)) 34 xbps730p06ws0 aa j screw, x34 (for chassis, pwb) 35 lx-bza364wjf7 aa n x screw, x4 (for sub woofer) 36 pspaga889wjkz ad n x spacer (coner top) (15x25x6), x2 37 pspaga891wjkz ac n x spacer (coner bottom) (18x18x4), x2 38 pspaga892wjkz ac n x spacer (coner top) (15x25x8) 39 tlabnb037wjzz ab n x serial label (back) 40 tlabnc391wjzz - n x serial label (side) 41 xbps730p10ws0 aa j screw, x5 (for lcd) 42 pspahc165wjzz aa n x himeron, x2 43 lx-bza170wjf9 aa n x screw, x4 44 xbps830p14js0 aa n x screw, x1 (for terminal) 45 xebs940p10000 ab j screw, x4 (for speaker) 46 xbps830p08js0 ab j screw, x17 (for rear cabinet) 47 pzetka538wjkz aw n x insulator 48 pzetka562wjkz ac n x ac barrier 49 cdai-a654wj01 bg n x stand base ass'y 50 cangkc708wj01 av n x support ass'y 51 cx-bza363wj01 ad n x stand screw ass'y 51-3 xbbs840p08000 aa n x screw free datasheet http:///
lc-40/46/52/60le810un (1st edition) 7 [5] cabinet and mechanical parts (lc-52le810un) 2-10 2-4 23 37 37 20 23 6 23 45 45 8 1-2 43 22 49 2-3 2-11 46 2 47 2-2 2-1 48 46 55 55 4 11 50 46 5 4 27 28 28 26 37 31 25 29 32 38 21 33 3 37 30 24 36 37 1 35 37 14 34 22 22 22 22 37 37 56-3 37 23 23 23 37 7 16 15 12 37 35 37 37 37 34 13 37 25 18 37 37 37 18 17 19 42 44 44 44 56 51 54 2-7 2-8 2-7 2-5 2-9 2-9 2-6 53 a k c a c a b main unit e n k m h a g n power/led drive unit j f m k g f j 52" lcd panel module b d f g k h r/c, led unit touch sensor unit d icon unit e b k j h d e b e g f free datasheet http:///
lc-40/46/52/60le810un (1st edition) 8 no. parts code price rank new mark part delivery description [5] cabinet and mechanical parts (lc-52le810un) 1 ccabac529wj31 bt n x front cabinet ass'y 1-2 hdecqb442wj3a aa n x r/c decoration cover 2 ccabbb695wj31 bm n x rear cabinet ass'y 2-1 not available - n x rear cabinet 2-2 hindpd699wjsa af n x terminal label s 2-3 hindpd700wjsa ad n x terminal label b 2-4 pspahc152wj3z aa n x ac himeron 2-5 pspahc159wjzz aa n x 170x10x0.5 himeron 2-6 pspahc160wjzz ab n x 300x10x0.5 himeron 2-7 pspahc166wjzz ab n x 445x8x0.5 himeron, x2 2-8 pspahc172wjzz ab n x 575x8x0.5 himeron, x2 2-9 pspahc173wjzz ab n x 695x8x0.5 himeron, x2 2-10 pspazc461wjzz ac n x spacer a 2-11 pzetka539wjkz az n x power barrir ! 3 qaccda074wjpz ag n x ac cord 4 lhldka011wjkz ab n x ac cord band 5 gcovad699wj3a ac n x ac cord cover 6 gcovad697wj3a af n x stand cover 7 langkc695wjfw ad n x lcd fixing metal angle b-r 8 lhldwa176wjuz ac j holder, x2 11 hindpd720wjsa ab n x model label 12 langkc694wjfw ad n x lcd fixing metal angle b-l 13 langkc696wjfw ad n x lcd fixing metal angle t-l 14 langkc697wjfw ad n x lcd fixing metal angle t-r 15 langkc698wjfw ab n x lcd fixing metal angle b-ma 16 langkc810wjfw ac n x lcd fixing metal angle b-mb 17 pmlt-a632wjzz ac n x absorber 18 qearza186wjzz ad n x ground part, x2 19 pclica014wjkz aa n x clip, x2 20 cangkc700wj31 ar n x stand angle ass'y 20-1 langkc700wjfw aq n x stand angle 20-2 not available - n x spacer, x2 21 rsp-za457wjzz ax n x speaker (sub woofer) 22 lhldwa175wjuz ac j holder, x10 23 lhldwa289wjkz ac n j holder, x6 24 pzetka538wjkz aw n x insulator 25 lhldza587wjkz ac j holder, x6 26 gcovad734wj00 af n x terminal cover s 27 gcovad735wj00 ae n x terminal cover b 28 nsftza362wjfw aa n x shaft, x4 29 qcnw-k548wjqz ae n x connecting cord 30 qcnw-k550wjqz ad n x connecting cord (pl:pow-lcd_ctl) 31 qcnw-k552wjqz ae n x connecting cord (lb:pow-main) 32 qcnw-k577wjqz aq n x connecting cord (lw:main-lcd_ctl) 33 qcnw-k574wjqz ae n x connecting cord (sb:main-woofer) 34 pspaga889wjkz ad n x spacer (coner top) (15x25x6) x2 35 pspaga891wjkz ac n x spacer (coner bottom) (18x18x4) x2 36 pspaga892wjkz ac n x spacer (coner top) (15x25x8) 37 xbps730p06ws0 aa j screw, x34 (for chassis, pwb) 38 lx-bza364wjf7 aa n x screw, x4 (for sub woofer) 42 qcnw-k562wjqz ar n x connecting cord (ra:man-en/ky/rc) 43 qcnw-k579wjqz ag n x connecting cord (sp:man-sp(l/r)) 44 xbps730p10ws0 aa j screw, x6 (for lcd) 45 rsp-za456wjzz au n x speaker, x2 (l/r) 46 xbps830p08js0 ab j screw, x19 (for rear cabinet) 47 xbps830p14js0 aa n x screw (for terminal) 48 xebs940p10000 ab j screw, x4 (for speaker) 49 lx-bza170wjf9 aa n x screw, x4 50 tlabnb037wjzz ab n x serial label (back) 51 tlabnc391wjzz - n x serial label (side) 53 pzetka562wjkz ac n x ac barrier 54 cdai-a654wj01 bg n x stand base ass'y 55 cangkc708wj01 n x support ass'y 56 cx-bza363wj01 ad n x stand screw ass'y 56-3 xbbs840p08000 aa n x screw free datasheet http:///
lc-40/46/52/60le810un (1st edition) 9 [6] cabinet and mechanical parts (lc-60le810un) 21 21 1 37 18 19 43 38 46 17 6 13 49 43 41 41 41 42 44 2-10 2-3 2-1 2-2 2-8 2-8 2-8 2-5 2-6 2-7 2-4 20 45 41 4 5 30 51 51 29 1-2 28 38 32 35 34 38 3 31 23 38 7 9 8 38 38 10 10 10 2 38 55 55 22 38 38 38 24 39 24 39 47 25 28 27 26 33 2-9 36 40 40 40 50 54 56 56 53 a k c a b a main unit e k m n h a f n m g f j 60" lcd panel module b f g l h g j k r/c, led unit touch sensor unit d icon unit e power/led drive unit k b d e b g f e j h free datasheet http:///
lc-40/46/52/60le810un (1st edition) 10 no. parts code price rank new mark part delivery description [6] cabinet and mechanical parts (lc-60le810un) 1 ccabac530wj31 bv n x front cabinet ass'y 1-2 hdecqb442wj3a aa n x r/c decoration cover 2 ccabbb696we01 br n x rear cabinet ass'y 2-1 not available n x rear cabinet 2-2 hindpd699wjsa af n x terminal label s 2-3 hindpd700wjsa ad n x terminal label b 2-4 pspahc152wj3z aa n x ac himeron 2-5 pspahc159wjzz aa n x 170x10x0.5 himeron 2-6 pspahc160wjzz ab n x 300x10x0.5 himeron 2-7 pspahc170wjzz ab n x 630x8x0.5 himeron, x2 2-8 pspahc170wjzz ab n x 385x8x0.5 himeron, x6 2-9 pspazc462wjzz ac n x spacer b, x2 2-10 pzetka539wjkz az n x insulator ! 3 qaccda074wjpz ag n x ac cord 4 lhldka011wjkz ab n x ac cord band 5 gcovad699wj3a ac n x ac cord cover 6 gcovad698wj3a am n x stand cover 7 langkc695wjfw ad n x lcd fixing metal angle b-r 8 langkc696wjfw ad n x lcd fixing metal angle t-l 9 langkc697wjfw ad n x lcd fixing metal angle t-r 10 lhldwa175wjuz ac j holder, x5 13 hindpd721wjsa ab n x model label 17 cangkc709wj01 ay n x support ass'y 18 cdai-a655wj01 bl n x stand base ass'y 19 lx-bza366wjzz aa n x screw, x6 (for support angle) 20 gcovad702wjka ar n x support cover 21 rsp-za456wjzz au n x speaker, x2 (l/r) 22 langkc698wjfw ab n x lcd fixing metal angle b-ma, x4 23 langkc694wjfw ad n x lcd fixing metal angle b-l 24 langkc701wjfw af n x stand angle, x2 25 rsp-za457wjzz ax n x speaker (sub woofer) 26 lhldwa289wjkz ac j holder, x4 27 pzetka538wjkz aw n x insulator 28 lhldza587wjkz ac j holder, x6 29 gcovad734wj00 af n x terminal cover s 30 gcovad735wj00 ae n x terminal cover b 31 qcnw-k550wjqz ad n x connecting cord (pl:pow-lcd_ctl) 32 qcnw-k566wjqz ae n x connecting cord (pd:pow-main) 33 qcnw-k570wjqz ae n x connecting cord (sb:main-woofer) 34 qcnw-k578wjqz aq n x connecting cord (lw:main-lcd_ctl) 35 qcnw-k575wjqz ae n x connecting cord (lb:pow-main) 36 qcnw-k567wjqz as n x connecting cord (ra:man-en/ky/rc) 37 qcnw-k568wjqz ag n x connecting cord (sp:man-sp(l/r)) 38 xbps730p06ws0 aa j screw, x27 (for chassis, pwb) 39 xbps840p08000 aa n x screw, x12 (for stand angle) 40 xbps730p10ws0 aa j screw, x9 (for lcd) 41 xbps830p08js0 ab j screw, x19 (for rear cabinet) 42 xbps830p14js0 aa n x screw, x2 (for terminal) 43 xebs940p10000 ab j screw, x7 (for stand cover) 44 lx-bza170wjf9 aa n x screw, x4 45 xbps840p12000 aa n x screw, x3 (for support cover) 46 xbps950p12ks0 aa n x screw, x4 (for stand fixing metal) 47 lx-bza364wjf7 aa n x screw, x4 (for sub woofer) 49 tlabnb037wjzz ab n x serial label (back) 50 tlabnc391wjzz - n x serial label (side) 51 nsftza362wjfw aa n x shaft, x4 53 pspahc160wjzz ab n x himeron, x2 54 pzetka562wjkz ac n x ac barrier 55 pspaga890wjkz ae n x spacer coner-top, x2 56 pspaga892wjkz ac n x spacer coner-bottom, x2 free datasheet http:///
lc-40/46/52/60le810un (1st edition) 11 [7] supplied accessories no. parts code price rank new mark part delivery description [7] supplied accessories x1 rrmcga840wjsa ar n x remote control x2 lhldwa289wjkz ac j cable clamp, x5 x3 cdai-a653wj01 be n x stand base ass'y (LC-40LE810UN) x3 cdai-a654wj01 bg n x stand base ass'y (lc-46/52le810un) x4 tins-e589wjzz al n x operation manual x5 not available ad x "aaa" size battery x6 tcadea243wjzz ab n x enquete card x7 tman-a030wjzz ab n x netflix handbill x8 tman-a032wjzz ab n x conection guide x9 tgan-b489wjzz n x guarantee card x10 cangkc707wj01 n x support ass'y (LC-40LE810UN) x10 cangkc708wj01 av n x support ass'y (lc-46/52le811un) x11 cx-bza363wj01 ad n x stand screw ass'y x11-3 xbbs840p08000 ab screw remote control unit aaa size battery cable clamp operation manual connection guide x1 x8 x5 x2 x3 x10 x11 x4 stand screw ass'y support ass'y free datasheet http:///
lc-40/46/52/60le810un (1st edition) 12 [8] packing parts (lc-40le810u n) (not replacement item) front s11 s11 x1 x4 x6 x7 x8 x9 x10 x2 x5 x11 x11-3 s8 s7 s5 s3 s3 s6 x3 s3 s2 s4 s4 s1 free datasheet http:///
lc-40/46/52/60le810un (1st edition) 13 no. parts code price rank new mark part delivery description [8] packing parts (l c-40le810un) (not replacement item) s1 spakcf500wjzz ay n x packing case s2 spakpb219wjzz ae n x wrapping paper s3 spakxc908wjzz an n x packing add. (top) s4 spakxc913wjzz at n x packing add. (bottom) s5 spakpb526wjzz - n x not available wrapping paper with the cangkc707wj01 s6 spakpb528wjzz - n x not available wrapping paper with the cdai-a653wj01 s7 ssaka0101gjzz aa n x polyethylene bag s8 ssakaa032wjzz ab j polyethylene bag s11 tlabka009wjzz aa n x case no. label free datasheet http:///
lc-40/46/52/60le810un (1st edition) 14 [9] packing parts (lc-46le810u n) (not replacement item) front s12 s12 s8 x4 s9 s4 s1 s5 s3 s5 s5 s2 s5 s7 x3 x10 s4 s4 x1 5 free datasheet http:///
lc-40/46/52/60le810un (1st edition) 15 no. parts code price rank new mark part delivery description [9] packing parts (l c-46le810un) (not replacement item) s1 spakcf501wjzz ay n x packing case s2 spakcf473wjzz ak n x bottom case s3 spakpa999wjzz af n x wrapping paper s4 spakxc909wjzz an n x packing add. (top) s5 spakxc914wjzz at n x packing add. (bottom) s6 spakpb527wjzz - n x not available wrapping paper with the cangkc708wj01 s7 spakpb529wjzz - n x not available wrapping paper with the cdai-a654wj01 s8 ssaka0101gjzz aa n x polyethylene bag s9 ssakaa032wjzz ab j polyethylene bag s12 tlabka009wjzz aa n x case no. label free datasheet http:///
lc-40/46/52/60le810un (1st edition) 16 [10] packing parts (lc-52le810 un) (not replacement item) front s12 s12 s8 x4 x6 x8 x9 x1 s9 x2 x5 x11 x11-3 s4 s4 s1 s5 s3 s5 s2 s5 s5 s6 x10 s7 x3 s4 free datasheet http:///
lc-40/46/52/60le810un (1st edition) 17 no. parts code price rank new mark part delivery description [10] packing parts (lc-52le81 0un) (not replacement item) s1 spakcf502wjzz az n x packing case s2 spackf474wjzz ak n x bottom case s3 spakpa992wjzz af n x wrapping paper s4 spakxc910wjzz ap n x packing add. (top) s5 spakxc915wjzz at n x packing add. (bottom) s6 spakpb527wjzz - n x not available wrapping paper with the cangkc708wj01 s7 spakpb529wjzz - n x not available wrapping paper with the cdai-a654wj01 s8 ssaka0101gjzz aa n x polyethylene bag s9 ssakaa032wjzz ab j polyethylene bag s12 tlabka009wjzz aa n x case no. label free datasheet http:///
lc-40/46/52/60le810un (1st edition) 18 [11] packing parts (lc-60le810 un) (not replacement item) s5 s5 s5 s5 s6 s6 s6 s4 s3 s1 s2 s6 s9 s5 s7 s8 x2 x5 x1 x4 x6 x7 x8 x9 free datasheet http:///
lc-40/46/52/60le810un (1st edition) 19 no. parts code price rank new mark part delivery description [11] packing parts (lc-60le81 0un) (not replacement item) s1 spakcf503wjzz bd n x packing case s2 spakcf475wjzz ar n x bottom case s3 spakpb427wjzz ah n x wrapping paper s4 spakpb518wjzz ae n x wrapping paper (for stand) s5 spakxc911wjzz av n x packing add. (top) s6 spakxc916wjzz ax n x packing add. (bottom) s7 ssaka0101gjzz aa n x polyethylene bag s8 ssakaa032wjzz ab j polyethylene bag s9 tlabka009wjzz aa n x case no. label [12] service jigs (use for servicing) n qcnw-c222wjqz aw j connecting cord l=1000mm 80pin lcd control to lcd panel unit x2 n qcnw-h184wjqz ax j connecting cord l=1000mm 12pin main to power unit (pd) n qcnw-f676wjqz bh j connecting cord l=1000mm 41pin main to lcd control (lw) n qcnw-g405wjqz ap j connecting cord l=1000mm 4pin main to lcd control (pl) n qcnw-g394wjqz av j connecting cord l=1000mm 9pin main to power (lb) free datasheet http:///
lc-40/46/52/60le810un (1st edition) copyright ? 2010 by sharp corporation all rights reserved. no part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher. sharp corporation av systems group cs promotion center yaita,tochigi 329-2193, japan mar. 2010 sh. ds free datasheet http:///
