www.baumer.com 6.12 dab mp4m-fc- output signal 10 v calibrated 4 - 20 ma load > 10 k ? shunt < 500 ? resolution < 0,035% fs < 0,07% fs measuring accuracy < 0,15% v.e. supply voltage range 15 - 33 vdc current consumption < 120 ma bridge excitation 5 vdc bridge completion 350 ? resistors zero reset active < 10 mv < 10 a reset input active 5 - 33 vdc galvanically separated inactive <1 vdc taring range 6 mv/v reset pulse < 1 ms holding time < 5 ms reset/operate offset < 10 mv < 15 a scanning rate > 1 ms frequency range (3 db) 300 hz display refresh rate 2/sec switching hysteresis limit switches < 0,5% fs max. load max. 50 ma limit switches signal polarity selectable features ? s/g bridge amplifer ? selectable bridge confguration ? limit switches with switching output ? peak value ? double-line display ? voltage and current output ? digital signal path electrical data dabu dabi bridge amplifer, selectable confguration dabx mp4m mechanical data control connection 13 pin terminal block sensor connection 13 pin terminal block shield connection 2 pin terminal block enclosure material aluminum/plastic operating temp. range 0...+65 c storage temperature -20...+80 c protection class ip 40 environmental conditions order code u voltage output 10 v i current output 4 - 20 ma output signal gain 0.50 =0,50 mv/v= 0-10 v resp. 4-20 ma 0.75 =0,75 mv/v= 0-10 v resp. 4-20 ma 1.00 =1,00 mv/v= 0-10 v resp. 4-20 ma 1.25 =1,25 mv/v= 0-10 v resp. 4-20 ma 2.00 =2,00 mv/v= 0-10 v resp. 4-20 ma delivery contents ? clamping clip for ground connection
www.baumer.com 6.13 6 dabx mp4m 1818 45, 5 75, 5 31 58 78 72, 5 pin signal description 1 +vs +supply voltage 2 v out1/iout 1 output signal 3 gnd -supply voltage 4 v out2/iout2 analog output (peak value) 5 gnd signal reference 6 switch s1 output 1 7 switch s2 output 2 8 reset taring of output signal 9 gnd signal reference 10 comm_logic logical reference 11 mode_0 mode 0 12 mode_1 mode 1 13 error output pin assignment control side pin signal description 1 +e +bridge excitation 2 +e +bridge excitation 3 +e' bridge to completion resistor 4 n.c. 5 n.c. 6 +s + signal input 7 -s C signal input 8 n.c. 9 -e' bridge to completion resistor 10 -e' bridge to completion resistor 11 -e C bridge excitation 12 -e C bridge excitation 13 shield pin assignment sensor side electrical connections dimensions (mm) supporting rail ts 35 (din en 60715 th35)
www.baumer.com 8.14 e+ e+ e+' 1 2 3 s+ 6 s- 7 e-' 9 e- 11 e- 12 e- 12 e- 11 e-' 10 s- 7 s+ 6 e+' 3 e+ 2 e+ 1 s- 7 e- 12 e+ 1 s+ 6 s+ 6 s- 7 d-pot +5 v dac 12 bit dac 12 bit led 1 green led 2 green lcd error led red /green +v s +5 v 3 up a d 12 bit e- ' 9 e- ' 10 e- 11 ,1 2 e+ ' 3 e+ 1, 2 shield 13 shield shield 1+ vs 3, 5, 9 gnd 2 vout /iout ( signal ) 4 vout 2/ iout 2 ( peak ) 13 error 7s witch 2 6s witch 1 8 reset 11 mode _0 12 mode _1 10 com _ logic electrical connections s/g bridge sensor side control side sensor side control side 2 x 1/4-bridge (diagonal) half bridge full bridge sensor side control side bridge amplifer, selectable confguration dabx mp4m
www.baumer.com 6.15 6 v/i out u t 1 t 2 t t measure reset peak signal dabx mp4m 1830 reset function v/i out output signal resp. peak signal reset reset input (active high) t 1 reset pulse (> 1 ms) t 2 reset holding time after reset-pulse (< 5 ms) control element connector 1 led 1 + 2 switch connector 2 dip-switch 1 led 3 dip-switch 2 display connector 3 dip-switch 1 selection of display connector 1 connection sensor side led 3 error display led 1 + 2 limit value (active/inactive) dip-switch 2 reset (active/inactive); signal polarity switch for limit value adjustment connector 3 shield connection connector 2 control side connection display double-line lc-display with back ground lighting
|
