opa703 opa2703 opa4703 opa704 opa2704 opa4704 cmos, rail-to-rail, i/o operational amplifiers features rail-to-rail input and output wide supply range: single supply: 4v to 12v dual supplies: 2 to 6 low quiescent current: 160 a full scale cmrr: 90db low offset: 160 v high speed: opa703: 1mhz, 0.6v/ s opa704: 5mhz, 3v/ s microsize packages: sot23-5, msop-8, tssop-14 low input bias current: 1pa applications automotive applications: audio, sensor applications, security systems portable equipment active filters transducer amplifier test equipment data acquisition description the opa703 and opa704 series op amps are opti- mized for applications requiring rail-to-rail input and output swing. single, dual, and quad versions are offered in a variety of packages. while the quiescent current is less than 200 a per amplifier, the opa703 still offers excellent dynamic performance (1mhz gbw and 0.6v/ s sr) and unity gain stability. the opa704 is optimized for gains of 5 or greater and provides 5mhz gbw and 3v/ s slew rate. the opa703 and opa704 series are fully specified and guaranteed over the supply range of 2v to 6v. input swing extends 300mv beyond the rail and the output swings to within 40mv of the rail. the single versions (opa703 and opa704 (1) ) are available in the microsize sot23-5 and in the stan- dard so-8 surface-mount as well as the dip-8 pack- ages. dual versions (opa2703 (1) and opa2704 (1) ) are available in the msop-8, so-8 and dip-8 packages. the quad opa4703 (1) and opa4704 (1) are available in the tssop-14 and so-14 packages. all are speci- fied for operation from ?5 c to +125 c. note: (1) opa2703, opa4703, opa704, opa2704, and opa4704 available q1 2001. copyright ?2000, texas instruments incorporated sbos180 printed in u.s.a. december, 2000 www.ti.com 1 2 3 5 4 v+ ?n out v +in opa703 opa704 (1) sot23-5 1 2 3 4 8 7 6 5 nc v+ out nc nc in +in v opa703 opa704 (1) so-8, dip-8 1 2 3 4 8 7 6 5 v+ out b in b +in b out a in a +in a v opa2703 (1) opa2704 (1) msop-8, so-8, dip-8 a b 1 2 3 4 5 6 7 14 13 12 11 10 9 8 out d in d +in d v +in c in c out c out a in a +in a v+ +in b in b out b opa4703 (1) opa4704 (1) tssop-14, so-14 ad bc o p a 70 4 o p a 7 0 4 opa704 o p a 7 0 4
opa703, opa704 2 sbos180 opa703na, ua, pa opa2703ea, ua, pa (1) opa4703ea, ua (1) opa703 specifications: v s = 10v boldface limits apply over the specified temperature range, t a = ?5 c to +125 c at t a = +25 c, r l = 20k connected to v s / 2 and v out = v s / 2, unless otherwise noted. parameter condition min typ max units offset voltage input offset voltage v os v s = 5v, v cm = 0v 160 750 v drift dv os /dt t a = ?5 c to +125 c 4 v/ c vs power supply psrr v s = 2v to 6v, v cm = 0v 5 100 v/v over temperature v s = 2v to 6v, v cm = 0v 125 v/v channel separation, dc r l = 20k 1 v/v f = 1khz 98 db input voltage range common-mode voltage range v cm (v ) 0.3 (v+) + 0.3 v common-mode rejection ratio cmrr v s = 5v, (v ) 0.3v < v cm < (v+) + 0.3v 70 90 db over temperature v s = 5v, (v? < v cm < (v+) 60 db v s = 5v, (v ) 0.3v < v cm < (v+) 2v 80 96 db over temperature v s = 5v, (v? < v cm < (v+) ?2v 66 db input bias current input bias current i b v s = 5v, v cm = 0v 1 10 pa input offset current i os v s = 5v, v cm = 0v 0.5 10 pa input impedance differential 4 10 9 || 4 || pf common-mode 5 10 12 || 4 || pf noise input voltage noise, f = 0.1hz to 10hz v s = 5v, v cm = 0v 6 vp-p input voltage noise density, f = 1khz e n v s = 5v, v cm = 0v 45 nv/ hz current noise density, f = 1khz i n v s = 5v, v cm = 0v 2.5 fa/ hz open-loop gain open-loop voltage gain a ol r l = 100k , (v )+0.1v < v o < (v+) 0.1v 120 db r l = 20k , (v )+0.075v < v o < (v+) 0.075v 106 110 db over temperature r l = 20k , (v?+0.075v < v o < (v+)?.075v 100 db r l = 5k , (v )+0.15v < v o < (v+) 0.15v 106 110 db over temperature r l = 5k , (v?+0.15v < v o < (v+)?.15v 100 db output voltage output swing from rail r l = 100k , a ol > 80db 40 mv r l = 20k , a ol > 106db 75 mv over temperature r l = 20k , a ol > 100db 75 mv r l = 5k , a ol > 106db 150 mv over temperature r l = 5k , a ol > 100db 150 mv output current i out |v s v out | < 1v 10 ma short-circuit current i sc 40 ma capacitive load drive c load see typical performance curve frequency response c l = 100pf gain-bandwidth product gbw g = +1 1 mhz slew rate sr v s = 5v, g = +1 0.6 v/ s settling time, 0.1% t s v s = 5v, 5v step, g = +1 15 s 0.01% v s = 5v, 5v step, g = +1 20 s overload recovery time v in gain = v s 3 s total harmonic distortion + noise thd+n v s = 5v, v o = 3vp-p, g = +1, f = 1khz 0.02 % power supply specified voltage range, single supply v s 412v specified voltage range, dual supplies v s 2 6v operating voltage range 3.6 to 12 v quiescent current (per amplifier) i q i o = 0 160 200 a over temperature 300 a temperature range specified range 55 125 c operating range 55 125 c storage range 65 150 c thermal resistance ja sot23-5 surface-mount 200 c/w msop-8 surface-mount 150 c/w tssop-14 surface-mount 100 c/w so-8 surface mount 150 c/w so-14 surface mount 100 c/w dip-8 100 c/w note: (1) opa2703 and opa4703 available q1 2001.
opa703, opa704 3 sbos180 opa704na, ua, pa (1) opa2704ea, ua, pa (1) opa4704ea, ua (1) opa704 specifications: v s = 10v boldface limits apply over the specified temperature range, t a = ?5 c to +125 c at t a = +25 c, r l = 20k connected to v s / 2 and v out = v s / 2, unless otherwise noted. parameter condition min typ max units offset voltage input offset voltage v os v s = 5v, v cm = 0v 160 750 v drift dv os /dt t a = ?5 c to +125 c 4 v/ c vs power supply psrr v s = 2v to 6v, v cm = 0v 5 100 v/v over temperature v s = 2v to 6v, v cm = 0v 125 v/v channel separation, dc r l = 20k 1 v/v f = 1khz 98 db input voltage range common-mode voltage range v cm (v ) 0.3 (v+) + 0.3 v common-mode rejection ratio cmrr v s = 5v, (v ) 0.3v < v cm < (v+) + 0.3v 70 90 db over temperature v s = 5v, (v? < v cm < (v+) 60 db v s = 5v, (v ) 0.3v < v cm < (v+) 2v 80 96 db over temperature v s = 5v, (v? < v cm < (v+) ?2v 66 db input bias current input bias current i b v s = 5v, v cm = 0v 1 10 pa input offset current i os v s = 5v, v cm = 0v 0.5 10 pa input impedance differential 4 10 9 || 4 || pf common-mode 5 10 12 || 4 || pf noise input voltage noise, f = 0.1hz to 10hz v s = 5v, v cm = 0v 6 vp-p input voltage noise density, f = 1khz e n v s = 5v, v cm = 0v 45 nv/ hz current noise density, f = 1khz i n v s = 5v, v cm = 0v 4 fa/ hz open-loop gain open-loop voltage gain a ol r l = 100k , (v )+0.1v < v o < (v+) 0.1v 120 db r l = 20k , (v )+0.075v < v o < (v+) 0.075v 106 110 db over temperature r l = 20k , (v?+0.075v < v o < (v+)?.075v 100 db r l = 5k , (v )+0.15v < v o < (v+) 0.15v 106 110 db over temperature r l = 5k , (v?+0.15v < v o < (v+)?.15v 100 db output voltage output swing from rail r l = 100k , a ol > 80db 40 mv r l = 20k , a ol > 106db 75 mv over temperature r l = 20k , a ol > 100db 75 mv r l = 5k , a ol > 106db 150 mv over temperature r l = 5k , a ol > 100db 150 mv output current i out |v s v out | < 1v 10 ma short-circuit current i sc 40 ma capacitive load drive c load see typical performance curve frequency response c l = 100pf gain-bandwidth product gbw g = +5 5 mhz slew rate sr v s = 5v, g = +5 3 v/ s settling time, 0.1% t s v s = 5v, 5v step, g = +5 18 s 0.01% v s = 5v, 5v step, g = +5 21 s overload recovery time v in gain = v s 0.6 s total harmonic distortion + noise thd+n v s = 5v, v o = 3vp-p, g = +5, f = 1khz 0.025 % power supply specified voltage range, single supply v s 412v specified voltage range, dual supplies v s 2 6v operating voltage range 3.6 to 12 v quiescent current (per amplifier) i q i o = 0 160 200 a over temperature 300 a temperature range specified range 55 125 c operating range 55 125 c storage range 65 150 c thermal resistance ja sot23-5 surface-mount 200 c/w msop-8 surface-mount 150 c/w tssop-14 surface-mount 100 c/w so-8 surface mount 150 c/w so-14 surface mount 100 c/w dip-8 100 c/w note: (1) opa704, opa2704, and opa4704 available q1 2001.
opa703, opa704 4 sbos180 minimum package recommended drawing package ordering transport product description gain package number marking number (1) media opa703na single, gbw = 1mhz 1 sot23-5 331 a03 opa703na/250 tape and reel "" """" opa703na/3k tape and reel opa703ua single, gbw = 1mhz 1 so-8 182 opa703ua opa703ua rails "" """" opa703ua/2k5 tape and reel opa703pa single, gbw = 1mhz 1 dip-8 006 opa703pa opa703pa rails opa2703ea (2) dual, gbw = 1mhz 1 msop-8 337 b03 opa2703ea/250 tape and reel "" """" opa2703ea/2k5 tape and reel OPA2703UA (2) dual, gbw = 1mhz 1 so-8 182 OPA2703UA OPA2703UA rails "" """" OPA2703UA/2k5 tape and reel opa2703pa (2) dual, gbw = 1mhz 1 dip-8 006 opa2703pa opa2703pa rails opa4703ea (2) quad, gbw = 1mhz 1 tssop-14 357 opa4703ea opa4703ea/250 tape and reel "" """" opa4703ea/2k5 tape and reel opa4703ua (2) quad, gbw = 1mhz 1 so-14 235 opa4703ua opa4703ua rails "" """" opa4703ua/2k5 tape and reel opa704na (2) single, gbw = 5mhz 5 sot23-5 331 a04 opa704na/250 tape and reel "" """" opa704na/3k tape and reel opa704ua (2) single, gbw = 5mhz 5 so-8 182 opa704ua opa704ua tape and reel "" """" opa704ua/2k5 tape and reel opa704pa (2) single, gbw = 5mhz 5 dip-8 006 opa704pa opa704pa rails opa2704ea (2) dual, gbw = 5mhz 5 msop-8 337 b04 opa2703ea/250 tape and reel "" """" opa2703ea/2k5 tape and reel opa2704ua (2) dual, gbw = 5mhz 5 so-8 182 opa2704ua opa2704ua rails "" """" opa2704ua/2k5 tape and reel opa2704pa (2) dual, gbw = 5mhz 5 dip-8 006 opa2704pa opa2704pa rails opa4704ea (2) quad, gbw = 5mhz 5 tssop-14 357 opa4704ea opa4704ea/250 tape and reel "" """" opa4704ea/2k5 tape and reel opa4704ua (2) quad, gbw = 5mhz 5 so-14 235 opa4704ua opa4704ua rails "" """" opa4704ua/2k5 tape and reel note: (1) models with a slash (/) are available only in tape and reel in the quantities indicated (e.g., /3k indicates 3000 dev ices per reel). ordering 3000 pieces of opa703na/3k will get a single 3000-piece tape and reel. (2) opa2703, opa4703, opa704, opa2704, and opa4704 available q1 2001. package/ordering information supply voltage, v+ to v ................................................................. 13.2v signal input terminals, voltage (2) ..................... (v ) 0.3v to (v+) +0.3v current (2) .................................................... 10ma output short-circuit (3) .............................................................. continuous operating temperature .................................................. 55 c to +125 c storage temperature ..................................................... 65 c to +150 c junction temperature .................................................................... +150 c lead temperature (soldering, 10s) ............................................... +300 c notes: (1) stresses above these ratings may cause permanent damage. exposure to absolute maximum conditions for extended periods may degrade device reliability. (2) input terminals are diode-clamped to the power supply rails. input signals that can swing more than 0.3v beyond the supply rails should be current-limited to 10ma or less. (3) short-circuit to ground, one amplifier per package. absolute maximum ratings (1) electrostatic discharge sensitivity this integrated circuit can be damaged by esd. burr-brown recommends that all integrated circuits be handled with appropriate precautions. failure to observe proper handling and installation procedures can cause damage. esd damage can range from subtle performance degrada- tion to complete device failure. precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
important notice texas instruments and its subsidiaries (ti) reserve the right to make changes to their products or to discontinue any product or service without notice, and advise customers to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. all products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. ti warrants performance of its semiconductor products to the specifications applicable at the time of sale in accordance with ti's standard warranty. testing and other quality control techniques are utilized to the extent ti deems necessary to support this warranty. specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. customers are responsible for their applications using ti components. in order to minimize risks associated with the customer's applications, adequate design and operating safeguards must be provided by the customer to minimize inherent or procedural hazards. ti assumes no liability for applications assistance or customer product design. ti does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of ti covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. ti's publication of information regarding any third party's products or services does not constitute ti's approval, warranty or endorsement thereof. mailing address: texas instruments post office box 655303 dallas, texas 75265 copyright ? 2001, texas instruments incorporated
|
