55 nc nylon connectors df14 series (1.25mm pitch) df14 series n features 1. ultra-low profile designed to have a low profile on board, only right-angle models available. package height on a board: 2.5mm allows you to pick up signals from a very small space between boards. (see the figure 1 on the right.) 2. compatible with automatic packaging vacuum-operated header allows automatic emboss packaging. can be packed in magazines for delivery. 3. four-wall type prevents the sockets from rubbing the board. box construction prevents prying out, completely preventing mis- insertion. also, the wall on the board side prevents the socket from rubbing the board. reinforcement prevents separation of solder connections. n application lcd, notebook computers, portable information terminals, compact oa equipment, and various consumer equipment such as videomovies. 1.25 mm pitch ultra-low profile crimp connectors connector mounted on a board fig. 1
56 df14 series (1.25mm pitch) nc nylon connectors n product standard rated current 1a operating temp. 35~85?c(note 1) storage temp. 10~60?c (note 2) rating rated voltage ac150v operating humidity 40~80% storage humidity 40~70% (note 2) item standard conditions 1. insulation resistance 500 m or more measured at 100 vdc 2. withstand voltage no flashover or dielectric breakdown allowed ac500v 1 minute 3. contact resistance 30 m or less measured at 100 ma 4. insertion and withdrawals force min 0.3 n(30gf), max 3 n(300gf) to be measured with a steel pin of m 0.3?.002mm 5. vibration resistance no electrical discontinuity of 1 s or more allowed frequency: 10 - 55 hz, single-side amplitude: 0.75 mm, 3 directions for 2 hours 6. moisture resistance contact resistance: 30 m or less, insulation resistance:500m or more temperature: 40? c, humidity: 90 - 95%, allow 96 hours before measurement 7. temperature cycle contact resistance: 30 m or less, insulation resistance: 500 m or more (-55 c for 30 min. / 5 - 35 c for 10 min. / 85 c for 30 min. / 5 - 35 c for 10 min.) 5 cycles 8. insertion/extraction life contact resistance: 30 m or less solder-plated: 30 insertions/extractions 9. solder heat resistance no melting of resin affecting the connector performance allowed smt type reflow: at recommended man ual soldering: solder temperature: temperature profile 300 c for 3 seconds product part material processing ul rating crimp socket insulation polyamide resin beige ul94v-0 crimp socket terminal terminal phosphor bronze tin-plated insulation polyamide resin (note 1) beige ul94v-0 pin header terminal brass tin-plated fittings phosphor bronze tin-plated note 1: includes temperature rise when power is on. note 2: "storage" refers to a long period of storage without use of the product before being mounted on a board. the operating temperature and humidity ranges apply to the connectors mounted on a board when turned off, and connectors under temporary storage such as those being transported. note 3: the above standards are typical for the df14 series. the formal standards are stated in the delivery specifications. n material note 1: only the 30-pin models use the pin header insulation of pps resin (light brown). note 2: our tin plating is protected from whiskers. n structure of the product number the product specifications can be determined from the product number. when ordering, select products using the product numbers listed in this catalog 57 to 59 pages. l connector df14 - [ s - 1.25c l terminal df14 - 2628scf series name : df series no. : 14 a no. of contact : 2~10, 15, 20, 25, 30 ? type of connector s : single-row socket p : single-row pin header ? contact pitch : 1.25mm ? connection form / shape of terminal c : crimp case h : right angle smt a? ? ? series name : df 2628 : awg26~28 3032 : awg30~32 type of form / type of packaging scf : socket contact reel
57 nc nylon connectors df14 series (1.25mm pitch) n crimp socket [specification no.]: -**,(**) blank : 100 pcs. per pack (40) : 500 pcs. per package (41) : 1000 pcs. per package l applicable wire (tin-plated annealed copper wire) conductor size (core construction) coating diameter awg 26 (7cores/0.16mm) awg 28 (7cores/0.127mm) ?.54~?mm awg 30 (7cores/0.1mm) awg 32 (7cores/0.08mm) l recommended wire ul1571 l strip length 1.2~1.9mm note: contact our sales department for unspecified wires. v applicable crimping tool type hrs no. product no. applicable contact applicator 901-4548-1 ap105-df14-2628s df14-2628scf 901-4544-0 ap105-df14-3032s df14-3032scf press body 901-0005-4 cm-105 . . . . . . . . . manual crimping 550-0261-1 df14-2628/cr-ht df14-2628scf tool 550-0262-4 df14-3032/cr-ht df14-3032scf note 1: any problem caused by using a tool not approved by hirose is out of warranty. note 2: the manual crimping tool consecutively cuts carrier-fitted reel terminals. hrs no. product no. type quantity processing 538-0001-7- [[ df14-2628scf reel terminal 10,000 units per reel tin-plated 538-0003-2- [[ df14-3032scf reel terminal note 1: minimum order quantity of the models without a number specified is one pack containing 100 sockets. note 2: 500 and 1000 pieces per pack should be ordered in quantity of sockets. order in multiples of order units, e.g., 500, 10 00, 1500,-- . n crimp socket terminal hrs no. product no. no. of contact ab 538-0005-8- [[ df14- 2s-1.25c( [[ ) 2 4.45 1.25 538-0006-0- [[ df14- 3s-1.25c( [[ ) 3 5.70 2.50 538-0007-3- [[ df14- 4s-1.25c( [[ ) 4 6.95 3.75 538-0008-6- [[ df14- 5s-1.25c( [[ ) 5 8.20 5.00 538-0009-9- [[ df14- 6s-1.25c( [[ ) 6 9.45 6.25 538-0010-8- [[ df14- 7s-1.25c( [[ ) 7 10.70 7.50 538-0011-0- [[ df14- 8s-1.25c( [[ ) 8 11.95 8.75 538-0013-6- [[ df14- 9s-1.25c( [[ ) 9 13.20 10.00 538-0014-9- [[ df14-10s-1.25c( [[ ) 10 14.45 11.25 538-0054-3- [[ df14-15s-1.25c( [[ ) 15 20.70 17.50 538-0059-7- [[ df14-20s-1.25c( [[ ) 20 26.95 23.75 538-0064-7- [[ df14-25s-1.25c( [[ ) 25 33.20 30.00 538-0012-3- [[ df14-30s-1.25c( [[ ) 30 39.45 36.25 unit : mm photo shows engaged pins
58 df14 series (1.25mm pitch) nc nylon connectors guide post - provided guide post - not provided hrs no. product no. hrs no. product no. abcd 538-0021-4- [[ df14- 2p-1.25h ( [[ ) 538-0033-3- [[ df14a- 2p-1.25 h ( [[ ) 2 7.45 1.25 6.45 8.05 66 538-0022-7- [[ df14- 3p-1.25h ( [[ ) 538-0034-6- [[ df14a- 3p-1.25 h ( [[ ) 3 8.70 2.50 7.70 9.30 56 538-0023-0- [[ df14- 4p-1.25h ( [[ ) 538-0035-9- [[ df14a- 4p-1.25 h ( [[ ) 4 9.95 3.75 8.95 10.55 49 538-0024-2- [[ df14- 5p-1.25h ( [[ ) 538-0036-1- [[ df14a- 5p-1.25 h ( [[ ) 5 11.20 5.00 10.20 11.80 44 538-0025-5- [[ df14- 6p-1.25h ( [[ ) 538-0037-4- [[ df14a- 6p-1.25 h ( [[ ) 6 12.45 6.25 11.45 13.05 39 538-0026-8- [[ df14- 7p-1.25h ( [[ ) 538-0038-7- [[ df14a- 7p-1.25 h ( [[ ) 7 13.70 7.50 12.70 14.30 36 538-0027-0- [[ df14- 8p-1.25h ( [[ ) 538-0039-0- [[ df14a- 8p-1.25 h ( [[ ) 8 14.95 8.75 13.95 15.55 32 538-0028-3- [[ df14- 9p-1.25h ( [[ ) 538-0040-9- [[ df14a- 9p-1.25 h ( [[ ) 9 16.20 10.00 15.20 16.80 30 538-0029-6- [[ df14-10p-1.25h ( [[ ) 538-0041-1- [[ df14a-10p-1.25 h ( [[ ) 10 17.45 11.25 16.45 18.05 28 538-0084-4- [[ df14-15p-1.25h ( [[ ) 538-0114-3- [[ df14a-15p-1.25 h ( [[ ) 15 23.70 17.50 22.70 24.30 20 538-0089-8- [[ df14-20p-1.25h ( [[ ) 538-0119-7- [[ df14a-20p-1.25 h ( [[ ) 20 29.95 23.75 28.95 30.55 16 538-0094-8- [[ df14-25p-1.25h ( [[ ) 538-0124-7- [[ df14a-25p-1.25 h ( [[ ) 25 36.20 30.00 35.20 36.80 13 538-0020-1- [[ df14-30p-1.25h ( [[ ) 538-0045-2- [[ df14a-30p-1.25 h ( [[ ) 30 42.45 36.25 41.45 43.05 11 note 1: order magazine packaged products in multiples of the number in one magazine. note 2: order embossed packaged product in reels (1,000 pcs. per reel). unit : mm [specification no.]: -**,(**) (20) : tin-plated, magazine packaging (21) : tin-plated, embossed packaging v recommended board pattern v magazine dimensional drawing n right-angle pin header (smt) note 1: 2 ~ 5-pin models have no lock hole. note 2: the hole is not required for products without the guide boss. note 3: the hole is not required for products without the guide. no. of contacts no. of products in a magazine/ pcs./magazine
59 nc nylon connectors df14 series (1.25mm pitch) v embossed tape carrier dimensional drawing (complies with jis-c-0806) n 2 ~ 10 contacts n 15, 20, 25, 30 contacts insertion connector a b c d df14/14a- 2p-1.25h 2 16 7.5 16.4 . df14/14a- 3p-1.25h 3 16 7.5 16.4 . df14/14a- 4p-1.25h 4 24 11.5 24.4 . df14/14a- 5p-1.25h 5 24 11.5 24.4 . df14/14a- 6p-1.25h 6 24 11.5 24.4 . df14/14a- 7p-1.25h 7 24 11.5 24.4 . df14/14a- 8p-1.25h 8 24 11.5 24.4 . df14/14a- 9p-1.25h 9 24 11.5 24.4 . df14/14a-10p-1.25h 10 24 11.5 24.4 . df14/14a-15p-1.25h 15 44 20.2 44.4 40.4 df14/14a-20p-1.25h 20 44 20.2 44.4 40.4 df14/14a-25p-1.25h 25 56 26.2 56.4 52.4 df14/14a-30p-1.25h 30 56 26.2 56.4 52.4 unit : mm no. of contacts
60 df14 series (1.25mm pitch) nc nylon connectors v notes on use 1. recommended temperature profile (smt) note 1: you can solder a product up to two times under the same conditions, provided that the product is allowed to cool back to room temperature before the second soldering. note 2: the above temperature refers to the board surface temperature of the connector lead. 2. recommended soldering soldering iron temperature: 290 10 c, soldering time: less than 3 seconds conditions (smt) 3. recommended screen 0.15mm~0.2mm thickness (smt) 4. warp in board (smt) 0.03 mm or less at the center of the connector with the connector ends as the reference. 5. cleaning conditions see "guide to hirose nylon connectors." 6. connecting conditions see "guide to hirose nylon connectors." n because the crimp terminals are very small, use utmost care when crimping them in accordance with the"crimping conditions list" and "crimping quality standards." 7. precautions n when inserting or extracting the connectors, do not pry them forcibly, to prevent them from being damaged.
|
