low cost mmic mixer 1400 - 2100 mhz mamxss0013 m/a-com inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. m/a-com makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does m/a-com assume any liability whatsoever arising out of the use or application of any product(s) or information. ? north america tel: 800.366.2266 / fax: 978.366.2266 ? europe tel: 44.1908.574.200 / fax: 44.1908.574.300 ? asia/pacific tel: 81.44.844.8296 / fax: 81.44.844.8298 visit www.macom.com for additional data sheets and product information. v2 1 rohs compliant features ? +12 dbm input power @ 1 db compression ? high isolation, 28 db lo to rf ? +3 to +8 dbm lo drive level ? dc - 500 mhz 3 db if bandwidth ? does not require dc bias ? lead-free sot-25 package ? 100% matte tin plating over copper ? halogen-free ?green? mold compound ? 260c reflow compatible ? rohs* compliant version of md54-0006 description m/a-com?s mamxss0013 is a passive mixer that achieves the performance of a double balanced diode mixer in a lead-free sot-25 package. the mamxss0013 is ideally suited for use where high level rf signals and very wide dynamic range are required. typical applications include frequency up/ down conversion, modulation and demodulation in receivers and transmitters for base station and portable systems. the mamxss0013 uses fets as mixing elements to achieve very wide dynamic range in a low cost plastic package. the mixer operates with lo drive levels of +3 dbm to +8 dbm. the lo port may be externally tuned for operation in various frequency bands. m/a-com?s mamxss0013 is fabricated using a mature 0.5 micron gate length gaas mesfet process. the process features full passivation for increased performance and reliability. the mamxss0013 is 100% rf tested to ensure performance specification compliance. pin configuration pin no. pin name description 1 lo port lo input 2 ground ground 3 ground ground 4 rf port rf input 5 if port if output functional block diagram 4 5 3 2 1 rf if l1 c1 r1 lo part number package mamxss0013 bulk packaging mamxss0013tr-3000 3000 piece reel mamx-000013-001smb 1500 mhz configuration mamx-000013-002smb 1710 mhz configuration mamx-000013-003smb 2300 mhz configuration part 1500 mhz 1710 mhz 2300 mhz r1 470 ? 470 ? 820 ? l1 6.8 nh 4.7 nh 2.7 nh c1 3.3 pf 2.2 pf 2.2 pf lo frequency external circuitry parts list 2,3 2. the external lo matching network allows tuning from 1400 mhz to 2300 mhz. the networks given above are intended to serve as guidelines for matching in different bands. 3. all off-chip components are low-cost surface mount components obtainable from multiple sources (0.060 in. x 0.030 in. or 0.080 in. x 0.050 in). * restrictions on hazardous substanc es, european union directive 2002/95/ec. 1. reference application note m513 for reel size information. ordering information 1
low cost mmic mixer 1400 - 2100 mhz mamxss0013 m/a-com inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. m/a-com makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does m/a-com assume any liability whatsoever arising out of the use or application of any product(s) or information. ? north america tel: 800.366.2266 / fax: 978.366.2266 ? europe tel: 44.1908.574.200 / fax: 44.1908.574.300 ? asia/pacific tel: 81.44.844.8296 / fax: 81.44.844.8298 visit www.macom.com for additional data sheets and product information. v2 2 rohs compliant electrical specifications 4 : rf = 1850 mhz (-10 dbm), lo = 1710 mhz (+5 dbm), if = 140 mhz, t a = 25c parameter test conditions units min. typ. max. conversion loss db ? 8.0 9.0 isolation lo to rf lo to if rf to if db db db ? ? ? 28 15 15 ? ? ? vswr rf port lo port 3 if port ratio ratio ratio ? ? ? 2.0:1 2.0:1 2.0:1 ? ? ? input 1 db compression lo = +5 dbm, rf freq: 1850 mhz dbm ? 12 ? two-tone im ratio 5 two tones at -10 dbm each, tone spacing = 100 khz, if = 140 mhz dbc ? 55 ? 4. with external lo port matchi ng. see functional block diagram. 5. imr vs. rf drive can be calculated by the formula: imr = 40-1.5*pin. absolute maximum ratings 6,7 6. exceeding any one or combination of these limits may cause permanent damage to this device. 7. m/a-com does not recommend sustained operation near these survivability limits. parameter absolute maximum rf input power +27 dbm lo drive power +27 dbm operating temperature -40c to +85c storage temperature -65c to +150c 4x 38.3 27.3 41.3 39.9 45.4 52.5 64.7 77.1 57.0 78.7 3x 21.4 10.5 30.1 30.1 69.0 70.5 43.0 58.8 68.3 76.8 2x 9.0 -0.9 36.1 36.4 36.0 45.8 65.8 75.0 64.3 78.0 1x 1.9 -6.0 0 0 44.8 55.5 56.1 75.2 65.0 78.3 0x x x 8.1 8.3 45.5 54.4 56.8 72.3 72.9 74.3 0x 1x 2x 3x 4x harmonic of rf spurious table harmonic of lo the spurious table shows the spur ious signals resulting from the mixing of the rf and lo input signals, assuming down conversion. mixing produc ts are indicated relative to the if. the lower frequency mixing term is shown for two different rf input levels. the top number is for an rf input power of 0 dbm, the lower number is for -10 dbm. |nf rf - mf lo |, rf = 0 dbm |nf rf - mf lo |, rf = -10 dbm rf frequency = 1850 mhz lo frequency = 1710 mhz
low cost mmic mixer 1400 - 2100 mhz mamxss0013 m/a-com inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. m/a-com makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does m/a-com assume any liability whatsoever arising out of the use or application of any product(s) or information. ? north america tel: 800.366.2266 / fax: 978.366.2266 ? europe tel: 44.1908.574.200 / fax: 44.1908.574.300 ? asia/pacific tel: 81.44.844.8296 / fax: 81.44.844.8298 visit www.macom.com for additional data sheets and product information. v2 3 rohs compliant the pcb dielectric between rf traces and rf ground layers should be chosen to reduce rf discontinuities between 50 ? lines and package pins. m/a-com recommends an fr-4 dielectric thickness of 0.008? (0.2 mm) yielding a 50 ? line width of 0.015? (0.38). the recommended metalization is 1 ounce copper. recommended pcb configuration layout view lead-free sot-25 ? cross section view ? reference application note m538 for l ead-free solder reflow recommendations. meets jedec moisture sensitivity level 1 requirements.
low cost mmic mixer 1400 - 2100 mhz mamxss0013 m/a-com inc. and its affiliates reserve the right to make changes to the product(s) or information contained herein without notice. m/a-com makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does m/a-com assume any liability whatsoever arising out of the use or application of any product(s) or information. ? north america tel: 800.366.2266 / fax: 978.366.2266 ? europe tel: 44.1908.574.200 / fax: 44.1908.574.300 ? asia/pacific tel: 81.44.844.8296 / fax: 81.44.844.8298 visit www.macom.com for additional data sheets and product information. v2 4 rohs compliant typical performance curves vswr conversion loss (up/down) two-tone imr two-tone imr ? test conditions for down converter application : rf = 1850 mhz (-10 dbm), if = 140 mhz, lo = 1710 mhz (+5 dbm). ? test conditions for up converter application : lo = 1710 mhz (+5 dbm), if = 140 mhz (-10 dbm), rf = 1850 mhz. ? test conditions for wide-band application : rf = -10 dbm, if = 140 mhz, lo = +11 dbm, lo port resistively matched. lower lo drive operation is available for narrow band performance using external r eactive matching. the 3 db if bandwidth is 500 mhz. if frequencies above 200 mhz can be optimized for low conver sion loss by using external matching components. 7 8 9 10 1700 1800 1900 2000 rf frequency (mhz) 0 10 20 30 40 1700 1800 1900 2000 lo to if lo to rf rf to if rf frequency (mhz) wide-band performance curves isolation 1.0 2.0 3.0 4.0 5.0 1700 1800 1900 2000 lo rf rf frequency (mhz) 40 50 60 70 80 1700 1800 1900 2000 rf frequency (mhz) 40 50 60 70 80 1400 1575 1750 1925 2100 frequency (mhz) 7 8 9 10 1400 1575 1750 1925 2100 rf frequency (mhz) conversion loss
|
