View IPP5FAD2100_6625737.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

b-26 apem www.apem.com ip series latching action pushbutton switches for harsh environments distinctive features and specifications b ? ? latching action actuator remains in the low position when ?n? ? ? illuminated and non-illuminated ? ? compact behind-panel depth less than 20 mm (.787) ? ? flat round actuator for optional marking ? ? sealed to ip 67 environmental specifications ?degree of protection : ip 67 - see details page b36. ?shock resistance : 100 g according to iec 512-4, test 6c ?vibration resistance : 10-500hz - 10 g according to iec 512-4, test 6d ?salt spray : iec 512-6, test 11f ?robustness (non-illuminated sw.) : ik06 according to en 50102 (1 joule) ?operating temperature : -40? to +85? electrical and general specifications ?max. current/voltage rating with resistive load : 100ma 24vdc - life expectancy 200 000 cycles 2a 125vac - life expectancy 10 000 cycles (tested according to ul 1054) ?initial contact resistance : 100 m max. ?insulation resistance : 1 g min. at 500vdc ?dielectric strength : 1.500 vac rms between terminals 1.000 vac rms between terminals and frame panel thickness : 1,5 mm (.059) min. - 5,5 mm (.217) max. ?total travel : 2,5 mm (.098) ?operating force : 5,5 n +/- 1n ?contact bounce : 10 ms ?torque : 1,5 nm applied to nut ?soldering : 320? max. for 3 seconds materials ?case : pa-6t, ul 94-v0 ?plunger : polyamide 6/6 ?bushing/bezel : zinc die-cast (zamak), black painted ?contacts : silver, gold plated ?multi-wire lead awg20, section 0,6 mm 2 , ul approved ?led wire : awg26 ?lens : polycarbonate ?terminal seal : epoxy led component specifications led colour forward current super red (l0s) 20ma 20ma 10ma 10ma forward voltage 2v 2v 2v 3,5v max. lumin. intensity 180 mcd 280 mcd 28 mcd 22 mcd yellow (l0y) green (l0g) blue (l0b) a resistor must be series-connected by the user. resistor value = supply voltage - led for war d voltage led forward current new!
apem www.apem.com b-27 ip series latching action pushbutton switches for harsh environments overview b ip bezel shape c square r round, curved p round, flat terminals s solder lug f wire leads z1 quick-connect p straight pc electrical function 1 off - on plunger colour 1 blue 1/4 dark blue 2 black 3 green 5 yellow 6 red 7/1 white 8 bright chrome 9 orange contacts ad silver, gold plated led colour blank non-illum. l0s red l0y yellow l0g green l0b blue options 100 satin chrome bezel 101 bright chrome bezel 104 high plunger (non-illum. round models only) about this series on the following pages, you will find successively : model structure of switches and options in the same order as in above chart dimensions : first dimensions are in mm while inches are shown as bracketted numbers. a sealing boot is available to protect the switches against frost and sand (p/n u5125). it is presented at the end of the ip series and in section h. mounting accessories : standard hardware supplied : 1 hex nut 14 mm (.551) across flats and 1 o-ring. packaging unit : 25 pieces notice : please note that not all combinations of above numbers are available. refer to the following pages for further information. series
b-28 apem www.apem.com ip series latching action pushbutton switches for harsh environments square or round - illuminated b model structure ?four led colours ?tin plated led terminals square models ?12.00x0.75si 50010 (19.68.393) 1.50 min (.059 min) (.472diax0.75is) (.322) 12.40 (.488) 8.20 7.00 (.275) 12.00 (.472sq) (.224) 5.70 17.50 (.688sq) epoxy 16.00 max (.629 max) ? flat solder lug terminals ipc1sad off - on wire lead terminals ipc1fad off - on round models 50010 (19.68.393) 1.50 min (.059 min) (.322) 12.40 (.488) 8.20 7.00 (.275) ?12.00 (.472dia) (.224) 5.70 ?17.50 (.688dia) epoxy (.472diax0.75is) ?12.00x0.75si 16.00 max (.629 max) ? flat solder lug terminals ipr1sad off - on wire lead terminals ipr1fad off - on plunger colour 1 : blue - 1/4 : dark blue - 2 : black - 3 : green - 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome - 9 : orange led colour options l0s : red - l0y : yellow - l0g : green - l0b : blue 100 : satin chrome bezel 101 : bright chrome bezel wire colours : black : contact, red : led anode(+), blue : led cathode(-) off on (.090) 2. 3 0 (.125) 3 .20 (.110) 2. 8 0 1.40 (.055) (.0 9 4) 2.40 (. 33 0) 8 .40 (.110) 2. 8 0 1.20 (.047) quick-connect z1 solder lug s (.0 39 ) 3 .40 (.1 33 ) 1.00 straight p also available with straight pc : ipr1pad or quick-connect terminals : ipr1z1ad also available with straight pc : ipc1pad or quick-connect terminals : ipc1z1ad
apem www.apem.com b-29 ip series latching action pushbutton switches for harsh environments square or round - non-illuminated b model structure square models ?12.00x0.75si 50010 (19.68.393) 1.50 min (.059 min) (.472diax0.75is) (.322) 12.40 (.488) 8.20 7.00 (.275) 12.00 (.472sq) (.224) 5.70 17.50 (.688sq) epoxy 16.00 max (.629 max) ? flat solder lug terminals ipc1sad off - on wire lead terminals ipc1fad off - on round models epoxy 14.10 (.555) (.688dia) ?7.50 7.00 (.275) (.472dia) ?2.00 (.275) 7.00 8.20 (.488) 12.40 (.322) (.472diax0.75is) (.059 min) 1.50 min (19.68?393) 500?0 ?2.00x0.75si ?2.00 (.472dia) 2.00 (.078) (.078) 2.00 ? flat curved actuator solder lug terminals ipr1sad off - on wire lead terminals ipr1fad off - on flat actuator solder lug terminals ipp1sad off - on wire lead terminals ipp1fad off - on plunger colour 1 : blue - 1/4 : dark blue - 2 : black - 3 : green - 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome - 9 : orange mounting panel cut-out matrix mounting back of panel space requirement ? 3 .60 (.5 3 5dia) 12.90 (.507) (.5 3 1dia) ?1 3 .50 1 1.50min-5.50m a x (.059 min-.216m a x) 20.00 (.7 8 7) 20.00 (.7 8 7) (.7 8 7) 20.00 (.751) 19.10 options 100 : satin chrome bezel 101 : bright chrome bezel 104 : high plunger (for round model only) also available with straight pc : ipc1pad or quick-connect terminals : ipc1z1ad also available with straight pc : ip?pad or quick-connect terminals : ip?z1ad 104 ipr 104 ipp ?2.00 (.472dia) (.1 8 5) 4.70 ?12.00 (.472dia) (.185) 4.70 plunger marking available on ipp models (symbol 10 mm max.). on request.
b-30 apem www.apem.com ip series momentary pushbutton switches for harsh environments distinctive features and specifications b ? ? illuminated and non-illuminated ? ? tactile feedback ? ? wide variety of configurations ? ? flat round actuator for optional marking ? ? sealed to ip 67 environmental specifications ?degree of protection : ip 67 ?shock resistance : 100 g according to iec 512-4, test 6c ?vibration resistance : 10-500hz - 10 g according to iec 512-4, test 6d ?salt spray : iec 512-6, test 11f ?robustness (non-illuminated sw.) : ik06 according to en 50102 (1 joule) ?operating temperature : -40? to +125? electrical specifications ?max. current/voltage rating with resistive load : 500ma 48vac - 200ma 50vdc - 200ma 250vac ?initial contact resistance : 100 m max. ?insulation resistance : 1 g min. at 500vdc ?dielectric strength : 1.500 vac rms ?electrical life at full load : 500.000 cycles ?contact bounce : 10 ms materials ?case : thermoplastic ul94-v0 ?plunger : polyamide 6/6 ?bushing/bezel : zinc die-cast (zamac), black painted ?contacts : silver, gold plated ?multi-wire lead awg20, section 0,6 mm 2 , ul approved ?led wire : awg26 ?lens : polycarbonate ?terminal seal : epoxy general specifications ?panel thickness : 1,5 mm (.059) min. 4 mm (.157 max.) ?total travel : 1,5 mm (.059) ?operating force : 2n to 5n ?mechanical life : 1.000.000 cycles ?torque : 1,5 nm max. applied to nut ?soldering : 320? max. for 3 sec. led component specifications led colour forward current super red (l0s) 20ma 20ma 10ma 10ma 20ma forward voltage 2v 2v 2v 3,5v 3,5v max. lumin. intensity 125 mcd 125 mcd 20 mcd 20 mcd 280 mcd yellow (l0y) green (l0g) blue (l0b) white (l0w) a resistor must be series-connected by the user. resistor value = supply voltage - led for war d voltage led forward current new!
apem www.apem.com b-31 ip series momentary pushbutton switches for harsh environments overview b ip series bezel shape c square r round, curved p round, flat terminals s solder lugs f wire leads p straight pc (non-illum.) z1 quick-connect (non-ill., no only ) electrical function 3 normally open (no) 5 nc/no combined (non-illuminated) plunger colour 1 blue 1/4 dark blue 2 black 3 green 5 yellow 6 red 7/1 white 8 bright chrome 9 orange contacts ad silver, gold plated led colour blank non-illum . l0s super red l0y yellow l0g green l0b blue l0w white about this series on the following pages, you will find successively : model structure of switches and options in the same order as in above chart dimensions : first dimensions are in mm while inches are shown as bracketted numbers. a sealing boot is available to protect the switches against frost and sand. it is presented at the end of the series and in section h. mounting accessories : standard hardware supplied : 1 hex nut 14 mm (.551) across flats and 1 o-ring. the hex nut is presented in section i (part number u166). packaging unit : 25 pieces notice : please note that not all combinations of above numbers are available. refer to the following pages for further information. options 100 satin chrome bezel 101 bright chrome bezel 104 high plunger (non-illum. round models only)
b-32 apem www.apem.com ip series momentary pushbutton switches for harsh environments square - illuminated b model structure ?high brightness illumination ?five led colours ?tin plated led terminals solder lug terminals 12.00x0.75si (.047) 1.50 5.20 (.015) (.204) (.059) 2.00 (.078) 5.08 (.200) (.267) 1.20 (.251) 6.40 6.80 0.40 epoxy (.472diax0.75is) 5.00 (.196) 1.50 min (.059 min) 12.00 (.472sq) 17.50 (.688sq) 2.00 (.078) 6.10 (.240) ? flat ipc3sad normally open sealed wire lead terminals 12.00x0.75 s i 500?0 (19.6 8 ? 3 9 3 ) (.6 88s q) 1.50 min (.059 min) 16.00 m a x (.629 m a x) 6. 8 0 (.267) (.472diax0.75i s ) 5.00 (.196) 12.00 (.472 s q) (.07 8 ) 2.00 17.50 ? flat ipc3fad normally open +- plunger colour 1 : blue - 1/4 : dark blue - 2 : black - 3 : green - 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome - 9 : orange led colour l0s : super red - l0y : yellow - l0g : green l0b : blue - low : white wire colours : black : no contact, red : led anode(+), blue : led cathode(-) cathode (-) led options 100 : satin chrome bezel 101 : bright chrome bezel
apem www.apem.com b-33 ip series momentary pushbutton switches for harsh environments square - non-illuminated b model structure ?double function (nc/no combined) with a short behind-panel depth solder lug terminals 12.00x0.75si (.047) 1.50 5.20 (.204) (.059) 2.00 (.078) 5.08 (.200) (.015) (.472diax0.75is) 6.40 (.251) 1.20 6.80 (.267) 0.40 epoxy 5.00 1.50 min (.196) 12.00 (.472sq) (.059 min) (.078) 17.50 (.688sq) 2.00 no no nc nc/no no ? flat ipc3sad normally open ipc5sad nc/no combined sealed wire lead terminals 12.00x0.75 s i 500?0 (19.6 8 ? 3 9 3 ) 1.50 min (.059 min) (.472diax0.75i s ) (.267) 16.00 m a x (.629 m a x) 6. 8 0 5.00 (.196) 12.00 (.472 s q) (.07 8 ) 2.00 17.50 (.6 88s q) no nc/no ? flat ipc3fad normally open ipc5fad nc/no combined plunger colour 1 : blue - 1/4 : dark blue - 2 : black - 3 : green - 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome - 9 : orange options 100 : satin chrome bezel 101 : bright chrome bezel wire colours (nc/no) : black : no, blue : nc function 3 (n0) function 5 (nc/no) 5.20 (.204) 1.00 (.039) 4.55 (.179) 1.20 2.80 (.047) (.110) 8.70 2.40 (.342) (.094) straight p quick-connect z1 also available with straight pc terminals : ipc3pad (no) or ipc5pad (nc/no) and quick-connect terminals : ipc3z1ad (no only)
b-34 apem www.apem.com ip series momentary pushbutton switches for harsh environments round - illuminated b model structure ?high brightness illumination ?five led colours ?tin plated led terminals solder lug terminals 12.00x0.75si 17.50 (.688dia) 12.00 (.472dia) (.047) 1.50 (.059) (.204) (.015) 5.20 (.200) (.078) 2.00 5.08 epoxy 0.40 (.472diax0.75is) (.267) (.251) 1.20 6.80 6.40 1.50 min 5.00 (.059 min) (.196) (.078) 2.00 6.10 (.240) ? flat ipr3sad normally open sealed wire lead terminals 12.00x0.75 s i (19.6 8 ? 3 9 3 ) 500?0 12.00 (.472dia) (.6 88 dia) 17.50 (.196) 5.00 (.059 min) 1.50 min 2.00 (.07 8 ) (.472diax0.75i s ) 16.00 m a x (.629 m a x) (.267) 6. 8 0 ? flat ipr3fad normally open +- plunger colour 1 : blue - 1/4 : dark blue - 2 : black - 3 : green - 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome - 9 : orange led colour l0s : super red - l0y : yellow - l0g : green l0b : blue - l0w : white wire colours : black : no contact, red : led anode(+), blue : led cathode(-) cathode (-) led options 100 : satin chrome bezel 101 : bright chrome bezel
apem www.apem.com b-35 ip series momentary pushbutton switches for harsh environments round - non-illuminated b function 3 (no) function 5 (nc/no) model structure ?double function (nc/no combined) with a short behind-panel depth solder lug terminals no no nc nc/no no 2.00 (.07 8 ) (.059 min) 1.50 min (.196) 5.00 (.472diax0.75i s ) 0.40 epoxy (.267) 6. 8 0 1.20 6.40 (.251) 5.0 8 (.200) 2.00 (.07 8 ) 5.20 (.015) (.204) (.059) 1.50 (.047) (.472dia) 12.00 (.6 88 dia) 17.50 12.00x0.75 s i ? flat curved actuator, no ipr3sad curved actuator, nc/no ipr5sad flat actuator, no ipp3sad flat actuator, nc/no ipp5sad sealed wire lead terminals nc/no no (.472diax0.75i s ) 6. 8 0 (.267) (.519) 1 3 .20 (.07 8 ) 2.00 1.50 min (.059 min) 5.00 (.196) 17.50 (.6 88 dia) (.472dia) 12.00 500?0 (19.6 8 ? 3 9 3 ) 12.00x0.75 s i ? flat curved actuator, no ipr3fad curved actuator, nc/no ipr5fad flat actuator, no ipp3fad flat actuator, nc/no ipp5fad plunger colour 1 : blue - 1/4 : dark blue - 2 : black - 3 : green - 5 : yellow - 6 : red - 7/1 : white - 8 : bright chrome - 9 : orange wire colours (nc/no) : black : no, blue : nc 100 : satin chrome bezel 101 : bright chrome bezel 104 : high plunger options 5.20 (.204) 1.00 (.039) 4.55 (.179) 1.20 2.80 (.047) (.110) 8.70 2.40 (.342) (.094) straight p quick-connect z1 also available with straight pc terminals : ip?pad (no) or ip?pad (nc/no) and quick-connect terminals : ip?z1ad (no only) plunger marking available on ipp models (symbol 10 mm max.). on request. 104 ipr 104 ipp 12.00 (.472dia) (.185) 4.70 12.00 (.472dia) (.1 8 5) 4.70
b-36 apem www.apem.com ip series momentary pushbutton switches for harsh environments b sealing ip 67 for the whole series degree of protection provided by the enclosures of electric appliances according to iec 529, din 40050 and nfc 20-010. ip 6 7 (ingress protection) totally protected protected against the effects of against dust immersion up to 1 m water (30 mn) solder lug version wire lead version mounting panel cut-out matrix mounting back of panel space requirement tactile feedback cross section operating forces/ travels diagram (indicative nominal curve) 13.60 (.535dia) (.531dia) 13.50 12.90 (.507) 1 1.50min-4max (.059 min-.157max) 20.00 (.787) 20.00 (.787) (.787) 20.00 (.688) 17.50 1 m 1 m ? elastomeric membrane ? o-ring ? o-ring 1 2 switching point force (n) travel (mm) 1.5 1.2 0.6 3 the above illustrations show non-illuminated models.
additional sealing for round plungers only, illuminated or non-illuminated. by silicone boot for protection against frost and abrasion by sand. order separately. - transparent : u5125 - blue : u5125-1 - black : u5125-2 - red : u5125-6 operating temperature : -40? to +125? life expectancy : 500.000 cycles apem www.apem.com b-37 ip series momentary pushbutton switches for harsh environments b luminance measurement mode test conditions transparent lens light source luminance-meter ls110 25cm (.748 dia) 1 9 .00 (.377) 9 .60 led types test results * * in our lab conditions for blue and white led, consult factory. measured in a dark room luminance forward current l0s (super red) 4000 cd/m 2 20ma l0y (yellow) l0g (green) 3500 cd/m 2 400 cd/m 2 20ma 10ma

▲Up To Search▲

Price & Availability of IPP5FAD2100

	To Download IPP5FAD2100 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .