View TC32MCDB713_5322056.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? 2006 microchip technology inc. ds21402c-page 1 tc32m features: ? incorporates the functionality of the industry standard tc1232 (processor monitor, watchdog and manual override reset controller) into a small, lower cost package ? guards against unstable processor operation resulting from power ?brown-out? ? automatically halts and restarts an out-of- control microprocessor ? output can be wire-ored, or hooked to manual reset push-button switch ? space-saving 3-pin to-92 or sot-223 package applications: ? all microprocessor-based systems ? battery powered computers and controllers ? automotive systems ? intelligent instruments ? critical processor monitoring ? embedded controllers device selection table package type general description: the tc32m is a fully-integrated processor supervisor in a 3-pin package. it provides three important func- tions to safeguard processor sanity: precision power on/off reset control, watchdog timer and external reset override. on power-up, the tc32m holds the processor in the reset state for a minimum of 500 msec after v dd is within tolerance to ensure a stable system start-up. microprocessor sanity is monitored by the on-board watchdog circuit. the microprocessor must provide a high-to-low level shift (through an external resistor divider) on the rs pin of the tc32m. should the processor fail to supply this signal within the specified time-out period (typically 700 msec), an out-of-control processor is indicated and the tc32m issues a processor reset as a result. the output of the tc32m can be wire-ored with a push-button switch (or electronic signal) to override the tc32m and unconditionally reset the processor. when connected to a push-button switch, the tc32m provides contact debounce. the tc32m is packaged in a space-saving to-92 or sot-223 package. it provides all of the functionality of the industry standard tc1232 in a smaller, lower cost configuration. part number package temp. range tc32mcdb sot-223 0c to +70c tc32mczb to-92 0c to +70c tc32medb sot-223 -40c to +85c tc32mezb to-92 -40c to +85c 1 12 4 3 23 gnd gnd tc32mcdb tc32medb tc32mczb tc32mezb v dd v dd v dd rs rs economonitor? ? 3-pin system supervisor with power supply monitor and watchdog
tc32m ds21402c-page 2 ? 2006 microchip technology inc. functional block diagram typical operating circuit v dd v ref2 v ref1 tc32m watchdog timer rs gnd dv detector delay timer 5v r1, 10 k r2, 10 k rs tc32m microcontroller reset po.1 reset
? 2006 microchip technology inc. ds21402c-page 3 tc32m 1.0 electrical characteristics absolute maximum ratings* supply voltage (v dd to gnd) .............................+6.0v input voltage any pin..... (gnd ? 0.3v) to (v dd +0.3v) operating temperature range tc32mc package........................... 0c to +70c tc32me package ........................ -40c to +85c storage temperature range ............. -65c to +150c *stresses above those listed under ?absolute maxi- mum ratings? may cause permanent damage to the device. these are stress ratings only and functional operation of the device at these or any other conditions above those indicated in the operation sections of the specifications is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. tc32m electrical specifications recommended dc operating conditions: t a = -40c to +85 c unless otherwise noted. symbol parameter min typ max units test conditions v dd supply voltage 4.5 ? 5.5 v v ih rs input high level for pb 2.0 ? ? v v il rs input low level for pb ? ? 0.3 v dc electrical characteristics: v dd = 4.5v to 5.5v, t a = -40c to +85 c unless otherwise noted. symbol parameter min typ max units test conditions i il rs input leakage -1 ? +1 ma i ol rs output current 2.0 10 ? ma v ol = 0.4v i cc operating current ? 50 200 a note 1 v sth rs strobe high level (v dd ? 0.5v) ? ? v figure 3-1 v stl rs strobe low level 2.00 ? (v dd ? 1.5v) v figure 3-1 v rst reset threshold 4.25 ? 4.50 v v dd falling ( note 2 , figure 3-3) capacitance electrical characteristics: t a = 25c unless otherwise noted. symbol parameter min typ max units test conditions c in input capacitance ? ? 5 pf c out output capacitance ? ? 7 pf ac electrical characteristics: t a = -40c to +85 c, v dd = 5v 10%, unless otherwise noted. symbol parameter min typ max units test conditions t rst reset active time 500 700 900 msec figure t st rs strobe pulse width 500 ? ? nsec figure 3-1 t td watchdog time-out period 500 700 900 msec figure 3-1 t rpd v dd detect to rs low ? ? nsec figure 3-1 note 1: no output load. 2: all voltages referenced to ground.
tc32m ds21402c-page 4 ? 2006 microchip technology inc. 2.0 pin descriptions the descriptions of the pins are listed in table 2-1. table 2-1: pin function table pin no. (sot-223, to-92) symbol description 1 gnd ground. 2v dd the +5v power supply input. 3 rs reset/strobe (bidirectional). the open drain goes active if: v dd falls below 4.5v nominal. if pulled low by an external electronic signal or switch closure. if the watchdog is not strobed within the minimum watchdog time-out period. during power-up and power-down. in the input mode, rs connects to a voltage level shift network (typically a resistor divider to v dd .) the watchdog timer is reset when processor causes a voltage level v stl to be applied to rs . 4v dd the +5v power supply input (sot-223 only).
? 2006 microchip technology inc. ds21402c-page 5 tc32m 3.0 detailed description the tc32m provides three important functions to safeguard stable processor operation: precision pro- cessor monitor, watchdog sanity timer and external override reset control. 3.1 processor monitor the rs pin is immediately driven low any time v dd is below the nominal threshold voltage. as a result, this pin is low when power is initially applied, holding the processor in its reset state. rs remains low for a minimum of 500 msec after v dd is within tolerance to allow the power supply and processor to stabilize. 3.2 watchdog timer the processor drives the rs pin with an input/output (i/o) line in series with an resistor voltage divider to v dd. pulling the bottom resistor of this divider low results in an internal voltage change ( strobe ) sufficient to reset the watchdog timer, but above the v il input threshold of the processor reset pin. the processor must continuously apply strobes in this manner within a set period to verify proper software execution. a momentary reset (500 msec minimum) is generated by the tc32m if a hardware or software failure keeps rs from being strobed within the watchdog time-out period. this action typically initiates the processor?s power-up routine. if the interruption persists, new reset pulses are generated each time-out period until rs is strobed. this time-out period is typically 700 msec. figure 3-1: watchdog strobe the software routine that drives the rs strobe must be in a section of the program that executes frequently enough so the time between toggles is less than one watchdog time-out period. the strobe signal can be derived from microprocessor address, data and/or control signals. typical circuit examples are shown in figure . 3.3 resistor value selection the values of r1 and r2 must be chosen to ensure a valid low strobe level (v stl ) on rs when the processor i/o line is low. the use of 10 k , 5% tolerance resistors are recommended. these values result in a nominal strobe level of 2.5 on rs (min/max of 2.13v/ 3.08v, assuming v dd = 5.0v 10%). other resistor values can be used, so long as the additive tolerances of the power supply and resistor values result in a strobe that falls within v sth and v stl under all additive tolerance conditions. v st l (max) t st t td rs note: t td is the maximum elapsed time between strobes which w ill keep the watchdog timer from forcing rs low. (a strobe is defined as a high-to-low transition from v sth to v stl ). v sth (min) v stl (min)
tc32m ds21402c-page 6 ? 2006 microchip technology inc. 3.4 external override reset control a built-in debounce circuit allows a push-button switch (pb) or other electronic signal to be wire-ored to this pin as an external reset override control. the external reset is required to be an active low signal. internally, this input is timed to provide a minimum reset pulse width of 500 msec. reference figure . t figure 3-2: rs pulled low by push- button reset figure 3-3: power-up/down reset timing 3.5 supply monitor noise sensitivity the tc32m is optimized for fast response to negative- going changes in v dd . systems with an inordinate amount of electrical noise on v dd (such as systems using relays), may require a 0.01 f bypass capacitor to reduce detection sensitivity. this capacitor should be installed as close to the tc32m as possible to keep the capacitor lead length short. figure 3-4: tc32m hardware connections (r1, r2 chosen to meet v sth , v stl ) pb closed pb open rs v ih t rst v il rs v il v ih v dd v rst t rst t rpd 5v 5v reset po.1 reset microcontroller microprocessor r2,10 k microcontroller example reset decoder address reset r1, 10 k microprocessor example rs tc32m rs tc32m r1, 10 k r2, 10 k
? 2006 microchip technology inc. ds21402c-page 7 tc32m 4.0 packaging information 4.1 package marking information package marking data not available at this time. 4.2 taping form component taping orientation for 3-pin sot-223 devices package carrier width (w) pitch (p) part per full reel reel size 3-pin sot-223 12 mm 8 mm 4000 13 in carrier tape, number of components per reel and reel size user direction of feed device marking pin 1 standard reel component orientation for 713 suffix device (mark right side up) w p mark face component taping orientation for 3-pin to-92 user direction of feed w p seal tape back tape m ark f ace m ark f ace m ark f ace
tc32m ds21402c-page 8 ? 2006 microchip technology inc. 4.3 package dimensions .264 (6.70) .248 (6.30) .122 (3.10) .114 (2.90) .287 (7.30) .264 (6.70) .146 (3.70) .130 (3.30) .091 (2.30) typ. .071 (1.80) max. .181 (4.60) typ. .036 (0.91) min. .041 (1.04) .033 (0.84) pin 1 .013 (0.33) .009 (0.24) .031 (0.80) .024 (0.60) .004 (0.10) .001 (0.02) 10 max. 3-pin sot-223 dimensions: inches (mm) .105 (2.67) .095 (2.41) .018 (0.46) .015 (0.38) .135 (3.43) min. .500 (12.70) min. .210 (5.33) .170 (4.32) .205 (5.21) .175 (4.45) .165 (4.19) .125 (3.18) .105 (2.67) .080 (2.03) .055 (1.40) .045 (1.14) .018 (0.46) .015 (0.38) to-92-3 dimensions: inches (mm)
? 2006 microchip technology inc. ds21402c-page9 tc32m product identification system to order or obtain information, e.g., on pricing or delivery, refer to the factory or the listed sales office. sales and support part code tc32m x xx temperature: c: commercial (0c to +70c) e: extended (-40c to +85c) package type: zb: 3-pin to-92 db: 3-pin sot223 db713: 3-pin tape & reel sot223 data sheets products supported by a preliminary data sheet may have an e rrata sheet describing minor operational differences and recom- mended workarounds. to determine if an erra ta sheet exists for a particular device, please contact one of the following: 1. your local microchip sales office 2. the microchip corporate literature center u.s. fax: (480) 792-7277 3. the microchip worldwide site (www.microchip.com) please specify which device, revision of silicon and data sheet (include literature #) you are using. new customer notification system register on our web site (www.microchip.com/cn) to receive the most current information on our products.
tc32m ds21402c-page10 ? 2006 microchip technology inc. notes:
? 2006 microchip technology inc. ds21402c-page 11 information contained in this publication regarding device applications and the like is prov ided only for your convenience and may be superseded by updates. it is your responsibility to ensure that your application m eets with your specifications. microchip makes no representations or war- ranties of any kind whether express or implied, written or oral, statutory or otherwise, related to the information, including but not limited to its condition, quality, performance, merchantability or fitness for purpose . microchip disclaims all liability arising from this information and its use. use of microchip?s products as critical components in life support systems is not authorized except with express written approval by microchip. no licenses are conveyed, implicitly or otherwise, under any microchip intellectual property rights. trademarks the microchip name and logo, the microchip logo, accuron, dspic, k ee l oq , micro id , mplab, pic, picmicro, picstart, pro mate, powersmart, rfpic, and smartshunt are registered trademarks of micr ochip technology incorporated in the u.s.a. and other countries. amplab, filterlab, migratable memory, mxdev, mxlab, picmaster, seeval, smartsensor and the embedded control solutions company are registered trademarks of microchip technology incorporated in the u.s.a. analog-for-the-digital age, app lication maestro, dspicdem, dspicdem.net, dspicworks, ecan, economonitor, fansense, flexrom, fuzzylab, in-circuit serial programming, icsp, icepic, linear active thermistor, mpasm, mplib, mplink, mpsim, pickit, picdem, picdem.net, piclab, pictail, powercal, powerinfo, powermate, powertool, real ice, rflab, rfpicdem, select mode, smart serial, smarttel, total endurance, uni/o, wiperlock and zena are trademarks of microchip technology incorporated in the u.s.a. and other countries. sqtp is a service mark of mi crochip technology incorporated in the u.s.a. all other trademarks mentioned herein are property of their respective companies. ? 2006, microchip technology incorporated, printed in the u.s.a., all rights reserved. printed on recycled paper. note the following details of the code protection feature on microchip devices: ? microchip products meet the specification cont ained in their particular microchip data sheet. ? microchip believes that its family of products is one of the most secure families of its kind on the market today, when used i n the intended manner and under normal conditions. ? there are dishonest and possibly illegal methods used to breach the code protection feature. all of these methods, to our knowledge, require using the microchip produc ts in a manner outside the operating specif ications contained in microchip?s data sheets. most likely, the person doing so is engaged in theft of intellectual property. ? microchip is willing to work with the customer who is concerned about the integrity of their code. ? neither microchip nor any other semiconduc tor manufacturer can guarantee the security of their code. code protection does not mean that we are guaranteeing the product as ?unbreakable.? code protection is constantly evolving. we at microchip are co mmitted to continuously improvin g the code protection features of our products. attempts to break microchip?s code protection feature may be a violation of the digital millennium copyright act. if such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that act. microchip received iso/ts-16949:2002 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in chandler and tempe, arizona and mountain view, california in october 2003. the company?s quality system processes and procedures are for its picmicro ? 8-bit mcus, k ee l oq ? code hopping devices, serial eeproms, microperipherals, nonvolatile memory and analog products. in addition, microchip?s quality system for the design and manufacture of development systems is iso 9001:2000 certified.
ds21402c-page 12 ? 2006 microchip technology inc. americas corporate office 2355 west chandler blvd. chandler, az 85224-6199 tel: 480-792-7200 fax: 480-792-7277 technical support: http://support.microchip.com web address: www.microchip.com atlanta alpharetta, ga tel: 770-640-0034 fax: 770-640-0307 boston westborough, ma tel: 774-760-0087 fax: 774-760-0088 chicago itasca, il tel: 630-285-0071 fax: 630-285-0075 dallas addison, tx tel: 972-818-7423 fax: 972-818-2924 detroit farmington hills, mi tel: 248-538-2250 fax: 248-538-2260 kokomo kokomo, in tel: 765-864-8360 fax: 765-864-8387 los angeles mission viejo, ca tel: 949-462-9523 fax: 949-462-9608 san jose mountain view, ca tel: 650-215-1444 fax: 650-961-0286 toronto mississauga, ontario, canada tel: 905-673-0699 fax: 905-673-6509 asia/pacific australia - sydney tel: 61-2-9868-6733 fax: 61-2-9868-6755 china - beijing tel: 86-10-8528-2100 fax: 86-10-8528-2104 china - chengdu tel: 86-28-8676-6200 fax: 86-28-8676-6599 china - fuzhou tel: 86-591-8750-3506 fax: 86-591-8750-3521 china - hong kong sar tel: 852-2401-1200 fax: 852-2401-3431 china - qingdao tel: 86-532-8502-7355 fax: 86-532-8502-7205 china - shanghai tel: 86-21-5407-5533 fax: 86-21-5407-5066 china - shenyang tel: 86-24-2334-2829 fax: 86-24-2334-2393 china - shenzhen tel: 86-755-8203-2660 fax: 86-755-8203-1760 china - shunde tel: 86-757-2839-5507 fax: 86-757-2839-5571 china - wuhan tel: 86-27-5980-5300 fax: 86-27-5980-5118 china - xian tel: 86-29-8833-7250 fax: 86-29-8833-7256 asia/pacific india - bangalore tel: 91-80-2229-0061 fax: 91-80-2229-0062 india - new delhi tel: 91-11-5160-8631 fax: 91-11-5160-8632 india - pune tel: 91-20-2566-1512 fax: 91-20-2566-1513 japan - yokohama tel: 81-45-471- 6166 fax: 81-45-471-6122 korea - gumi tel: 82-54-473-4301 fax: 82-54-473-4302 korea - seoul tel: 82-2-554-7200 fax: 82-2-558-5932 or 82-2-558-5934 malaysia - penang tel: 60-4-646-8870 fax: 60-4-646-5086 philippines - manila tel: 63-2-634-9065 fax: 63-2-634-9069 singapore tel: 65-6334-8870 fax: 65-6334-8850 taiwan - hsin chu tel: 886-3-572-9526 fax: 886-3-572-6459 taiwan - kaohsiung tel: 886-7-536-4818 fax: 886-7-536-4803 taiwan - taipei tel: 886-2-2500-6610 fax: 886-2-2508-0102 thailand - bangkok tel: 66-2-694-1351 fax: 66-2-694-1350 europe austria - wels tel: 43-7242-2244-399 fax: 43-7242-2244-393 denmark - copenhagen tel: 45-4450-2828 fax: 45-4485-2829 france - paris tel: 33-1-69-53-63-20 fax: 33-1-69-30-90-79 germany - munich tel: 49-89-627-144-0 fax: 49-89-627-144-44 italy - milan tel: 39-0331-742611 fax: 39-0331-466781 netherlands - drunen tel: 31-416-690399 fax: 31-416-690340 spain - madrid tel: 34-91-708-08-90 fax: 34-91-708-08-91 uk - wokingham tel: 44-118-921-5869 fax: 44-118-921-5820 w orldwide s ales and s ervice 10/31/05

▲Up To Search▲

Price & Availability of TC32MCDB713

	To Download TC32MCDB713 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .