1 ? fn6472.0 5962-0623501qpc, 5962-0623502QPC 500mhz rail-to-rail amplifiers the 5962-0623501qpc, 5962-0623502QPC are fully dscc smd compliant parts and the smd data sheets are available on the dscc website (http://www.dscc.dla.mil/pr ograms/specfind/default.asp). the 5962-0623501qpc is electrically equivalent to the el8102 and the 5962-0623502QPC is electrically equivalent to the el8103, reference these data sheets for additional information. these parts are single rail-to-rail amplifiers with a -3db bandwidth of 500mhz and slew rate of 600v/s. running off a very low 11ma supply current, the 5962-0623501qpc, 5962-0623502QPC also feature inputs that go to 0.15v below the v s - rail. the 5962-0623501qpc includes a fast-acting disable/power-down circuit. with a 25ns disable and a 200ns enable, the 5962-0623501qpc is ideal for multiplexing applications. the 5962-0623501qpc, 5962-0623502QPC are designed for a number of general pur pose video, communication, instrumentation, and industrial applications. both parts are available in 8 ld sbdip. all are specified for operation over the -55c to +125c temperature range. features ? 500mhz -3db bandwidth ? 600v/s slew rate ? low supply current = 11ma ? supplies from 3v to 5.0v ? rail-to-rail output ? input to 0.15v below v s - ? fast 25ns disable (5962-0623501qpc only) applications ? video amplifiers ? portable/hand-held products ? communications devices pinouts 5962-0623501qpc (8 ld sbdip) top view 5962-0623502QPC (8 ld sbdip) top view ordering information part number part marking temp. range (c) package pkg. dwg. # 5962-0623501qpc 5962-0623 501qpc -55 to +125 8 ld sbdip d8.3 5962-0623502QPC 5962-0623 502qpc -55 to +125 8 ld sbdip d8.3 1 2 3 4 8 7 6 5 - + nc in- in+ vs- enable vs+ out nc - + nc in- in+ vs- nc vs+ out nc data sheet march 29, 2007 caution: these devices are sensitive to electrosta tic discharge; follow proper ic handling procedures. 1-888-intersil or 1-888-468-3774 | intersil (and design) is a registered trademark of intersil americas inc. copyright intersil americas inc. 2007. all rights reserved all other trademarks mentioned are the property of their respective owners. 1 2 3 4 8 7 6 5
2 fn6472.0 march 29, 2007 important note: all parameters having min/max specifications are guaranteed. typ values are for information purposes only. unles s otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: t j = t c = t a absolute maxi mum ratings (t a = +25c) thermal information supply voltage from v s + to v s -. . . . . . . . . . . . . . . . . . . . . . . . . 5.5v input voltage . . . . . . . . . . . . . . . . . . . . . . . . v s + +0.3v to v s - -0.3v differential input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2v continuous output current . . . . . . . . . . . . . . . . . . . . . . . . . . . 20ma power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60.5mw storage temperature . . . . . . . . . . . . . . . . . . . . . . . .-65c to +150c ambient operating temperature . . . . . . . . . . . . . . .-55c to +125c operating junction temperature . . . . . . . . . . . . . . . . . . . . . . +150c caution: stresses above those listed in ?absolute maximum ratings? may cause permanent damage to the device. this is a stress o nly rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. electrical specifications v s + = 5v, v s - = gnd, t a = +25c, v cm = 2.5v, r l to 2.5v, a v = 1, unless otherwise specified parameter description conditions min typ max unit input characteristics r in input resistance common mode 3.5 m c in input capacitance 0.5 pf output characteristics r out output resistance a v = +1 30 m enable (5962-0623501qpc only) t en enable time 200 ns t ds disable time 25 ns ac performance bw -3db bandwidth a v = +1, r f = 0 , c l = 5pf 500 mhz a v = -1, r f = 1k , c l = 5pf 140 mhz a v = +2, r f = 1k , c l = 5pf 165 mhz a v = +10, r f = 1k , c l = 5pf 18 mhz bw 0.1db bandwidth a v = +1, r f = 0 , c l = 5pf 35 mhz peak peaking a v = +1, r l = 1k , c l = 5pf 1 db gbwp gain bandwidth product 200 mhz pm phase margin r l = 1k , c l = 5pf 55 sr slew rate a v = 2, r l = 100 , v out = 0.5v to 4.5v 600 v/s t r rise time 2.5v step , 20% to 80% 4 ns t f fall time 2.5v step , 20% to 80% 2 ns os overshoot 200mv step 10 % t pd propagation delay 200mv step 1 ns t s 0.1% settling time 200mv step 15 ns dg differential gain a v = +2, r f = 1k , r l = 150 0.01 % dp differential phase a v = +2, r f = 1k , r l = 150 0.01 e n input noise voltage f = 10khz 12 nv/ hz i n + positive input noise current f = 10khz 1.7 pa/ hz i n - negative input noise current f = 10khz 1.3 pa/ hz 5962-0623501qpc, 5962-0623502QPC
3 fn6472.0 march 29, 2007 simplified schematic diagram pin descriptions part pin name function 5962-0623501qpc 5962-0623502QPC 1, 5 1, 5, 8 nc not connected 2 2 in- inverting input 3 3 in+ non-inverting input 4 4 vs- negative power supply 6 6 out amplifier output 7 7 vs+ positive power supply 8 enable enable and disable input in+ in- i1 i2 r6 r3 r1 r2 q1 q2 r7 v bias1 q5 q6 r8 q7 q8 r9 q3 q4 r4 r5 v s- out v bias2 v s+ differential to drive generator single ended 5962-0623501qpc, 5962-0623502QPC
4 all intersil u.s. products are manufactured, asse mbled and tested utilizing iso9000 quality systems. intersil corporation?s quality certifications ca n be viewed at www.intersil.com/design/quality intersil products are sold by description only. intersil corpor ation reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnishe d by intersil is believed to be accurate and reliable. however, no responsibility is assumed by intersil or its subsidiaries for its use; nor for any infringements of paten ts or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of intersil or its subsidiari es. for information regarding intersil corporation and its products, see www.intersil.com fn6472.0 march 29, 2007 5962-0623501qpc, 5962-0623502QPC ceramic dual-in-line me tal seal packages (sbdip) notes: 1. index area: a notch or a pin one identification mark shall be locat- ed adjacent to pin one and shall be located within the shaded area shown. the manufacturer?s identification shall not be used as a pin one identification mark. 2. the maximum limits of lead di mensions b and c or m shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. 3. dimensions b1 and c1 apply to lead base metal only. dimension m applies to lead plating and finish thickness. 4. corner leads (1, n, n/2, and n/2+1) may be configured with a partial lead paddle. for this co nfiguration dimension b3 replaces dimension b2. 5. dimension q shall be measured from the seating plane to the base plane. 6. measure dimension s1 at all four corners. 7. measure dimension s2 from the top of the ceramic body to the nearest metallization or lead. 8. n is the maximum number of terminal positions. 9. braze fillets shall be concave. 10. dimensioning and tolerancing per ansi y14.5m - 1982. 11. controlling dimension: inch. bbb c a - b s c q l a seating base d plane plane s s -d- -a- -c- e a -b- aaa ca - b m d s s ccc ca - b m d s s d e s1 b2 b a e m c1 b1 (c) (b) section a-a base lead finish metal e a/2 s2 m a d8.3 mil-std-1835 cdip2-t8 (d-4, configuration c) 8 lead ceramic dual-in-line metal seal package symbol inches millimeters notes min max min max a - 0.200 - 5.08 - b 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 d - 0.405 - 10.29 - e 0.220 0.310 5.59 7.87 - e 0.100 bsc 2.54 bsc - ea 0.300 bsc 7.62 bsc - ea/2 0.150 bsc 3.81 bsc - l 0.125 0.200 3.18 5.08 - q 0.015 0.060 0.38 1.52 5 s1 0.005 - 0.13 - 6 s2 0.005 - 0.13 - 7 90 o 105 o 90 o 105 o - aaa - 0.015 - 0.38 - bbb - 0.030 - 0.76 - ccc - 0.010 - 0.25 - m - 0.0015 - 0.038 2 n8 88 rev. 0 4/94
|
