rev. 01.26.06 DS1300-3 1of 4 embedded power for business-critical continuity DS1300-3 1300 watts 12v distributed power system special features ? active power factor correction ? en61000-3-2 harmonic compliance ? active ac inrush control ? 2u x 3u form factor 7.5" long ? 13w/ in 3 ? +12vdc output ? +3.3vdc stand-by ? hot plug operation ? n + 1 redundant ? internal or'ing main and stand-by ? active current sharing ? internal cooling fans (60mm x 38mm) ?i 2 c communication interface bus ? eerpom for fru data ? green led status, power ok ? amber led status, power failed ? internal fan speed control ? fan fail output signal ? intel, ssi std. logic timing ? intel, ssi std. fru data format ? ac shutdown <85vac or 170vac ? one year warranty distributed power bulk front-end total output power: 1300 watts +12vdc main output; +3.3vdc stand-by output wide range input voltage: 90 - 264vac 180 - 264vac 1300w 90 - 264vac 910w electrical specifications safety input input range 90-264 vac, 910w 180 - 264 vac, 1300w frequency 47-63 hz, single phase ac inrush current 35a maximum inrush current efficiency >80% typical at full load, high line conducted emi fcc subpart j en55022 class a radiated emi fcc subpart j en55022 class a power factor 0.99 typical leakage current 0.75ma @ 240vac hold up time 12ms minimum output main dc voltage +12v @ 74a (90vac) or 106a (180vac) stand-by +3.3vsb @ 7a adjustment range factory set, no pot adjustments regulation +12vdc; 3%; +3.3vsb; 3% over current +12vdc; 110 - 130% latches off if overcurrent lasts over 1.5 seconds, otherwise it is auto recovery. +3.3vsb, 7a - 105% - 130% over voltage +12vdc; 13.7v 7% +3.3vsb; 4.0v 7% under voltage +12vdc; 11.0 - 11.4vdc turn-on delay +12voutput rise time <3 second max 5 - <200ms, monotonic rise i share 12v 15% from 50 - 100% load ul/cul 60950 (ul recognized) 1st edition (ul)60950-1-03 csa nemko+ cb report en60950 en60950 ce mark china ccc cb test report
rev. 01.26.06 DS1300-3 2of 4 embedded power for business-critical continuity ordering information o o u u t t p p u u t t n n o o m m i i n n a a l l o o u u t t p p u u t t v v o o l l t t a a g g e e s s e e t t p p o o i i n n t t s s e e t t p p o o i i n n t t t t o o l l e e r r a a n n c c e e t t o o t t a a l l r r e e g g u u l l a a t t i i o o n n m m i i n n i i m m u u m m c c u u r r r r e e n n t t m m a a x x i i m m u u m m c c u u r r r r e e n n t t o o u u t t p p u u t t r r i i p p p p l l e e p p / / p p main (>90vac) 12.00vdc 0.2% 3% 0a 74a 120mv main (180vac) 12.00vdc 0.2% 3% 1.0a 106a 120mv std-by 3.3vdc 1% 3% 0.5a 7.0a 50mv logic control ps_on an active low signal that turns on the 12vdc power rail. when this signal high, or left open, the 12vdc output turn off. the 3.3vsb output remains on. pok is a power good signal to be pulled low by the power supply to indicate that all the outputs are within regulation limits of the power supply. (turn-on delay 100 - 500ms) ps fail in the event of a power supply failure (ovp at any output, uv at any output, otp or other electrical failure), this signal shall go to a high state. ac ok high when ac is not ok, low if ac is ok present low i f psu is present, high if not present; pull high in system. fan fail low if one or both fans have failed ps_kill this pin shall quickly turn off the power supply and prevent arching of the dc output contacts. operating temperature: -10 to 50c ; 50% power derating at 70c storage temperature: -40c to +85c altitude, operating 10,000ft. electromagnetic susceptibility / input transients: en61000-3-2, -3-3 en61000-4-2, 4.3, 4-4, -4-5, 4-11 level en55024:1998 rohs, rs5 humidity: 5 to 95% rh, non-condensing shock and vibration specificatons complies with astec std. specifications, q3205 mtbf (demonstrated) 500k hrs at full load, 50c anti-smoke emission due to internal overload or internal failures fan life: 70,000 hrs @ 40c environmental specifications
rev. 01.26.06 DS1300-3 3of 4 embedded power for business-critical continuity note: dimensions given in mm and inches. 19.3 (162.9) 65.5 2.58" 143.3 5.65" 124.45 4.90" (4x) emi clip laird 77-020 ac inlet 15a c14 status led indicators tyco p/n 1-1450330-8 or fci p/n 51939-055 190.5 7.5" airflow direction ac cable retainer black hf green emi clip laird 771062031 165.6 6.52" model label 7.2 0.283" 71.1 2.80" (2x) emi clip laird 77-020 3d vie w power supply led's power supply condition pwr (green) fail (amber) no ac power to all psu off off no ac power to this psu only (includes no output, over voltage, over temperature) off on ac present / standby output on blinking off power supply dc outputs on and ok on off power supply failure (over current) off blinking
rev. 01.26.06 DS1300-3 4of 4 emerson network power and the emerson network power logo are trademarks and service marks of emerson electric co. ?2006 emerson electric co. embedded power for business-critical continuity emerson network power. the global leader in enabling business-critical continuity. emersonnetworkpower. com ac power connectivity dc power embedded power inbound power integrated cabinet solutions outside plant precision cooling site monitoring and services astec power 5810 van allen way carlsbad, ca 92008 usa telephone: +1 760 930 4600 facsimile: +1 760 930 0698 technical support: +1 888 41 astec or +1 407 241 2752 waterfront business park merry hill, dudley west midlands, dy5 1lx united kingdom telephone: +44 (0) 1384 842 211 facsimile: +44 (0) 1384 843 355 units 2111-2116, level 21 tower 1, metroplaza 223, hing fong road kwai fong, new territories hong kong telephone: +852 2437 9662 facsimile: +852 2402 4426 for global contact, visit: www.astecpower.com technicalsupport@astec.com while every precaution has been taken to ensure accuracy and completeness in this literature, astec power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. printed in us a dc output connector pinout assignment pin signal name pb p1 +12v pb p2 +12v return (pre-mate) pb p3 +12v pb p4 +12v return (pre-mate) pb p5 +12v pb p6 +12v return (pre-mate) pb p7 +12v pb p8 +12v return (pre-mate) a1 +3v3 stand-by a2 +3v3sb return a3 ps_present ( power supply seated) - (short pin) a4 pok (output power ok) a5 ps fail (failure signal) a6 spare a7 spare b1 +3v3 stand-by b2 +3v3sb return b3 pson (power enable signal) b4 pskill (power supply fast shutdown) - (short pin) b5 sda (i2c data signal b6 a2 (i2c address bit 2 signal) b7 fan fail (fan fail signal) c1 +3v3 stand-by c2 +3v3sb return c3 ac ok (ac input present) c4 +12v rmt sense c5 +12v rmt sense return c6 a1 (i2c address bit 1 signal) c7 +3v3 stand-by rmt sense return (-) d1 +3v3 stand-by d2 +3v3sb return d3 12 i s (+12v current share) d4 spare d5 scl (i2c clock signal) d6 a0 (i2c address bit 0 signal) d7 +3v3 stand-by rmt sense (+) p p 1 1 - - u u n n i i t t fci power blade fci p/n 51939-055 p p 1 1 - - m m a a t t e e mating connector (system side) fci power blade part number 51915-023 male connector as viewed from the rear of the supply ac input connector en60320 type c14
|
