View AD7322BRUZ_4835997.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

2-channel, software-selectable, true bipolar input, 1 msps, 12-bit plus sign adc ad7322 rev. a information furnished by analog devices is believed to be accurate and reliable. however, no responsibility is assumed by analog devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. specifications subject to change without notice. no license is granted by implication or otherwise under any patent or patent rights of analog devices. trademarks and registered trademarks are the property of their respective owners. one technology way, p.o. box 9106, norwood, ma 02062-9106, u.s.a. tel: 781.329.4700 www.analog.com fax: 781.461.3113 ?2005C2010 analog devices, inc. all rights reserved. features 12-bit plus sign sar adc true bipolar input ranges software-selectable input ranges 10 v, 5 v, 2.5 v, 0 v to +10 v 1 msps throughput rate two analog input channels with channel sequencer single-ended, true differential, and pseudo differential analog input capability high analog input impedance low power: 21 mw full power signal bandwidth: 22 mhz internal 2.5 v reference high speed serial interface power-down modes 14-lead tssop package i cmos process technology functional block diagram 04863-001 v in 0 dout sclk cs din v drive v in 1 v dd refin /o ut v cc agnd v ss dgnd control logic and registers 13-bit successive approximation adc t/h 2.5v vref i/p mux channel sequencer ad7322 figure 1. general description the ad7322 1 is a 2-channel, 12-bit plus sign, successive approx- imation analog-to-digital converter (adc) designed on the i cmos? (industrial cmos) process. i cmos is a process combining high voltage silicon with submicron cmos and complementary bipolar technologies. it enables the develop- ment of a wide range of high performance analog ics capable of 33 v operation in a footprint that no previous generation of high voltage parts could achieve. unlike analog ics using conventional cmos processes, i cmos components can accept bipolar input signals while providing increased performance, dramatically reduced power consumption, and reduced package size. the ad7322 can accept true bipolar analog input signals. the ad7322 has four software-selectable input ranges, 10 v, 5 v, 2.5 v, and 0 v to +10 v. each analog input channel can be independently programmed to one of the four input ranges. the analog input channels on the ad7322 can be programmed to be single-ended, true differential, or pseudo differential. the adc contains a 2.5 v internal reference. the ad7322 also allows for external reference operation. if a 3 v reference is applied to the refin/out pin, the ad7322 can accept a true bipolar 12 v analog input. minimum 12 v v dd and v ss supplies are required for the 12 v input range. the adc has a high speed serial interface that can operate at throughput rates up to 1 msps. product highlights 1. the ad7322 can accept true bipolar analog input signals, 10 v, 5 v, and 2.5 v, and 0 v to +10 v unipolar signals. 2. the two analog inputs can be configured as two single- ended inputs, one true differential input, or one pseudo differential input. 3. 1 msps serial interface. spi-/qspi?-/dsp-/microwire?- compatible interface. 4. low power, 31 mw maximum, at 1 msps throughput rate. 5. channel sequencer. table 1. similar devices device number throughput rate number of bits number of channels ad7329 1000 ksps 12-bit plus sign 8 ad7328 1000 ksps 12-bit plus sign 8 ad7327 500 ksps 12-bit plus sign 8 ad7324 1000 ksps 12-bit plus sign 4 ad7323 500 ksps 12-bit plus sign 4 ad7321 500 ksps 12-bit plus sign 2 1 protected by u.s. patent no. 6,731,232.
ad7322 rev. a | page 2 of 36 table of contents features .............................................................................................. 1 functional block diagram .............................................................. 1 general description ......................................................................... 1 product highlights ........................................................................... 1 revision history ............................................................................... 2 specifications ..................................................................................... 3 timing specifications .................................................................. 6 absolute maximum ratings ............................................................ 7 esd caution .................................................................................. 7 pin configuration and function descriptions ............................. 8 typical performance characteristics ............................................. 9 terminology .................................................................................... 13 theory of operation ...................................................................... 15 circuit information .................................................................... 15 converter operation .................................................................. 15 analog input structure .............................................................. 16 typical connecti on diagram ................................................... 18 analog input ............................................................................... 18 driver amplifier choice ............................................................ 20 registers ........................................................................................... 21 addressing registers .................................................................. 21 control register ......................................................................... 22 range register ............................................................................ 24 sequencer operation ..................................................................... 25 reference ..................................................................................... 26 v drive ............................................................................................ 26 modes of operation ....................................................................... 27 normal mode (pm1 = pm0 = 0) ............................................. 27 full shutdown mode (pm1 = pm0 = 1) ................................. 27 autoshutdown mode (pm1 = 1, pm0 = 0) ............................. 28 autostandby mode (pm1 = 0, pm0 = 1) ................................ 28 power vs. throughput rate ....................................................... 29 serial interface ................................................................................ 30 microprocessor interfacing ........................................................... 31 ad7322 to adsp-21xx .............................................................. 31 ad7322 to adsp-bf53x ........................................................... 31 application hints ........................................................................... 32 layout and grounding .............................................................. 32 power supply configuration .................................................... 32 outline dimensions ....................................................................... 33 ordering guide .......................................................................... 33 revision history 1/10rev. 0 to rev. a changes to power requirements, normal mode (operational), i cc and i drive parameter; and power dissipation, normal mode parameter, table 2 ............................................................................. 5 changes to endnote 1, table 4 ........................................................ 7 changes to table 6 .......................................................................... 15 changes to figure 25 and figure 26 ............................................. 16 changes to figure 30 and figure 31 ............................................. 17 changes to figure 33 and figure 34 ............................................. 18 changes to figure 39 ...................................................................... 19 changes to figure 40 and figure 41............................................. 20 changes to autostandby mode (pm1 = 0, pm = 1) section .... 28 changes to table 14 and table 15 ................................................ 31 added power supply configuration section .............................. 32 added table 16; renumbered sequentially ................................ 32 added figure 53; renumbered sequentially .............................. 32 updated outline dimensions ....................................................... 33 12/05revision 0: initial version
ad7322 rev. a | page 3 of 3 6 specifications unless otherwise noted, v dd = 12 v to 16.5 v, v ss = ?12 v to ?16.5 v, v cc = 4.75 v to 5.25 v, v drive = 2.7 v to 5.25 v, v ref = 2.5 v to 3.0 v internal/external, f sclk = 20 mhz, f s = 1 msps, t a = t max to t min ; for v cc < 4.75 v, all specifications are typical. table 2. b version parameter 1 min typ max unit test conditions/comments dynamic performance f in = 50 khz sine wave signal-to-noise ratio (snr) 2 76 db differential mode 72.5 db single-ended/pseudo differential mode signal-to-noise + d istortion (sinad) 2 75 db differential mode; 2.5 v and 5 v ranges 76 db differential mode; 0 v to +10 v and 10 v ranges 72 db single-ended/pseudo differential mode; 2.5 v and 5 v ranges 72.5 db single-ended/pseudo differential mode; 0 v to +10 v and 10 v ranges total harmonic distortion (thd) 2 ?80 db differential mode; 2.5 v and 5 v ranges ?82 db differential mode; 0 v to +10 v and 10 v ranges ?77 db single-ended/pseudo differential mode; 2.5 v and 5 v ranges ?80 db single-ended/pseudo differential mode; 0 v to +10 v and 10 v ranges peak harmonic or spurious noise (sfdr) 2 ?80 db differential mo de; 2.5 v and 5 v ranges ?82 db differential mode; 0 v to +10 v and 10 v ranges ?78 db single-ended/pseudo differential mode; 2.5 v and 5 v ranges ?79 db single-ended/pseudo differential mode; 0 v to +10 v and 10 v ranges intermodulation distortion (imd) 2 fa = 50 khz, fb = 30 khz second-order terms ?88 db third-order terms ?90 db aperture delay 3 7 ns aperture jitter 3 50 ps common-mode rejection ratio (cmrr) 2 ?79 db up to 100 khz ripple frequency; see figure 17 channel-to-channel isolation 2 ?72 db f in on unselected channels up to 100 khz; see figure 14 full power bandwidth 22 mhz at 3 db 5 mhz at 0.1 db dc accuracy all dc accuracy specifications are typical for 0 v to 10 v mode single-ended/pseudo differential mode: 1 lsb = fsr/4096; unless otherwise noted differential mode: 1 lsb = fsr/8192; unless otherwise noted resolution 13 bits no missing codes 12-bit plus sign (13 bits) bits differential mode 11-bit plus sign (12 bits) bits single-ended/pseudo differential mode integral nonlinearity 2 1.1 lsb differential mode 1 lsb single-ended/pseudo differential mode ?0.7/+1.2 lsb single-ended/pseudo differential mode (lsb = fsr/8192)
ad7322 rev. a | page 4 of 36 b version parameter 1 min typ max unit test conditions/comments differential nonlinearity 2 ?0.9/+1.5 lsb differential mo de; guaranteed no missing codes to 13 bits 0.9 lsb single-ended mode; guaranteed no missing codes to 12 bits ?0.7/+1 lsb single-ended/pseudo differential mode (lsb = fsr/8192) offset error 2 , 4 ?4/+9 lsb single-ended/pseudo differential mode ?7/+10 lsb differential mode offset error match 2 , 4 0.6 lsb single-ended/pseudo differential mode 0.5 lsb differential mode gain error 2 , 4 8 lsb single-ended/pseudo differential mode 14 lsb differential mode gain error match 2 , 4 0.5 lsb single-ended/pseudo differential mode 0.5 lsb differential mode positive full-scale error 2 , 5 4 lsb single-ended/pseudo differential mode 7 lsb differential mode positive full-scale error match 2 , 5 0.5 lsb single-ended/pseudo differential mode 0.5 lsb differential mode bipolar zero error 2 , 5 8.5 lsb single-ended/pseudo differential mode 7.5 lsb differential mode bipolar zero error match 2 , 5 0.5 lsb single-ended/pseudo differential mode 0.5 lsb differential mode negative full-scale error 2 , 5 4 lsb single-ended/pseudo differential mode 6 lsb differential mode negative full-scale error match 2 , 5 0.5 lsb single-ended/pseudo differential mode 0.5 lsb differential mode analog input input voltage ranges reference = 2.5 v; see table 6 (programmed via range register) 10 v v dd = 10 v min, v ss = ?10 v min, v cc = 2.7 v to 5.25 v 5 v v dd = 5 v min, v ss = ?5 v min, v cc = 2.7 v to 5.25 v 2.5 v v dd = 5 v min, v ss = ? 5 v min, v cc = 2.7 v to 5.25 v 0 to 10 v v dd = 10 v min, v ss = agnd min, v cc = 2.7 v to 5.25 v pseudo differential v in (?) input range v dd = 16.5 v, v ss = ?16.5 v, v cc = 5 v; see figure 40 and figure 41 3.5 v reference = 2.5 v; range = 10 v 6 v reference = 2.5 v; range = 5 v 5 v reference = 2.5 v; range = 2.5 v +3/?5 v reference = 2.5 v; range = 0 v to +10 v dc leakage current 80 na v in = v dd or v ss 3 na per channel, v in = v dd or v ss input capacitance 3 13.5 pf when in track, 10 v range 16.5 pf when in track, 5 v and 0 v to +10 v range 21.5 pf when in track, 2.5 v range 3 pf when in hold, all ranges reference input/output input voltage range 2.5 3 v input dc leakage current 1 a input capacitance 10 pf reference output voltage 2.5 v reference output voltage error at 25c 5 mv reference output voltage t min to t max 10 mv reference temperature coefficient 3 25 ppm/c reference output impedance 7
ad7322 rev. a | page 5 of 36 b version parameter 1 min typ max unit test conditions/comments logic inputs input high voltage, v inh 2.4 v input low voltage, v inl 0.8 v v cc = 4.75 v to 5.25 v 0.4 v v cc = 2.7 v to 3.6 v input current, i in 1 a v in = 0 v or v drive input capacitance, c in 3 10 pf logic outputs output high voltage, v oh v drive ? 0.2 v i source = 200 a output low voltage, v ol 0.4 v i sink = 200 a floating-state leakage current 1 a floating-state output capacitance 3 5 pf output coding straight natural binary coding bit set to 1 in control register twos complement coding bit set to 0 in control register conversion rate conversion time 800 ns 16 sclk cycles with sclk = 20 mhz track-and-hold acquisition time 2 , 3 305 ns full-scale step input; see the terminology section throughput rate 1 msps see the serial interface section; v cc = 4.75 v to 5.25 v 770 ksps v cc < 4.75 v power requirements digital inputs = 0 v or v drive v dd 12 16.5 v see table 6 v ss ?12 ?16.5 v see table 6 v cc 2.7 5.25 v see table 6 ; typical specifications for v cc < 4.75 v v drive 2.7 5.25 v normal mode (static) 0.9 ma v dd /v ss = 16.5 v, v cc /v drive = 5.25 v normal mode (operational) f s = 1 msps i dd 360 a v dd = 16.5 v i ss 410 a v ss = ?16.5 v i cc and i drive 3.4 ma v cc /v drive = 5.25 v autostandby mode (dynamic) f s = 250 ksps i dd 200 a v dd = 16.5 v i ss 210 a v ss = ?16.5 v i cc and i drive 1.3 ma v cc /v drive = 5.25 v autoshutdown mode (static) sclk on or off i dd 1 a v dd = 16.5 v i ss 1 a v ss = ?16.5 v i cc and i drive 1 a v cc /v drive = 5.25 v full shutdown mode sclk on or off i dd 1 a v dd = 16.5 v i ss 1 a v ss = ?16.5 v i cc and i drive 1 a v cc /v drive = 5.25 v power dissipation normal mode 31 mw v dd = 16.5 v, v ss = ?16.5 v, v cc = 5.25 v 21 mw v dd = 12 v, v ss = ?12 v, v cc = 5 v full shutdown mode 38.25 w v dd = 16.5 v, v ss = ?16.5 v, v cc = 5.25 v 1 temperature range is ?40c to +85c. 2 see the terminology section. 3 sample tested during initial release to ensure compliance. 4 unipolar 0 v to 10 v range with straight binary output coding. 5 bipolar range with twos complement output coding.
ad7322 rev. a | page 6 of 3 6 timing specifications unless otherwise noted, v dd = 12 v to 16.5 v, v ss = ?12 v to ?16.5 v, v cc = 2.7 v to 5.25 v, v drive = 2.7 v to 5.25, v drive v cc , v ref = 2.5 v to 3.0 v internal/external, t a = t max to t min . 1 table 3. limit at t min , t max parameter v cc < 4.75 v v cc = 4.75 v to 5.25 v unit description f sclk 50 50 khz min 14 20 mhz max t convert 16 t sclk 16 t sclk ns max t sclk = 1/f sclk t quiet 75 60 ns min minimum time between end of serial read and next falling edge of cs t 1 12 5 ns min minimum cs pulse width t 2 2 25 20 ns min cs to sclk setup time; bipolar input ranges (10 v, 5 v, 2.5 v) 45 35 ns min unipolar input range (0 v to 10 v) t 3 26 14 ns max delay from cs until dout three-state disabled t 4 57 43 ns max data access time after sclk falling edge t 5 0.4 t sclk 0.4 t sclk ns min sclk low pulse width t 6 0.4 t sclk 0.4 t sclk ns min sclk high pulse width t 7 13 8 ns min sclk to data valid hold time t 8 40 22 ns max sclk falling edge to dout high impedance 10 9 ns min sclk falling edge to dout high impedance t 9 4 4 ns min din setup time prior to sclk falling edge t 10 2 2 ns min din hold time after sclk falling edge t power-up 750 750 ns max power up from autostandby 500 500 s max power up from full shutdown/autoshutdown mode, internal reference 25 25 s typ power up from full shutdown /autoshutdown mode, external reference 1 sample tested during initial release to ensure compliance. all input signals are specified with tr = tf = 5 ns (10% to 90% of v drive ) and timed from a voltage level of 1.6 v. 2 when using the 0 v to 10 v unipolar range, running at 1 msps throughput rate with t 2 at 20 ns, the mark space ratio must be limited to 50:50. zero 1 2 3 4 5 13 14 15 16 write zero reg sel lsb msb add0 sign db11 db10 db2 db1 db0 t 2 t 6 t 4 t 9 t 10 t 3 t 7 t 5 t 8 t 1 t quiet t convert sclk cs dout three- state three-state din zero identification bit 04863-002 don?t care figure 2. serial interface timing diagram
ad7322 rev. a | page 7 of 36 absolute maximum ratings t a = 25c, unless otherwise noted table 4. parameter rating v dd to agnd, dgnd ?0.3 v to +16.5 v v ss to agnd, dgnd +0.3 v to ?16.5 v v dd to v cc v cc ? 0.3 v to 16.5 v v cc to agnd, dgnd ?0.3 v to +7 v v drive to agnd, dgnd ?0.3 v to +7 v agnd to dgnd ?0.3 v to +0.3 v analog input voltage to agnd 1 v ss ? 0.3 v to v dd + 0.3 v digital input voltage to dgnd ?0.3 v to +7 v digital output voltage to gnd ?0.3 v to v drive + 0.3 v refin to agnd ?0.3 v to v cc + 0.3 v input current to any pin except supplies 2 10 ma operating temperature range ?40c to +85c storage temperature range ?65c to +150c junction temperature 150c tssop package ja thermal impedance 113.5c/w jc thermal impedance 30c/w pb-free temperature, soldering reflow 260(0)c esd 2.5 kv 1 if the analog inputs are driven from alternative v dd and v ss supply circuitry, schottky diodes should be placed in series with the ad7322s v dd and v ss supplies. see the power suppl y configuration section. 2 transient currents of up to 100 ma do not cause scr latch-up. stresses above those listed under absolute maximum ratings may cause permanent damage to the device. this is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. exposure to absolute maximum rating conditions for extended periods may affect device reliability. esd caution
ad7322 rev. a | page 8 of 36 pin configuration and fu nction descriptions 04863-003 1 2 3 4 5 6 7 ad7322 14 13 12 11 10 9 8 dgnd dout v drive v in 1 v dd v cc sclk top view (not to scale) din dgnd agnd v in 0 v ss refin/out cs figure 3. pin configuration table 5. pin function descriptions pin no. mnemonic description 1 cs chip select. active low logic input. this input provid es the dual function of initiating conversions on the ad7322 and framing the serial data transfer. 2 din data input. data to be written to the on-chip registers is provided on this inp ut and is clocked into the register on the falling edge of sclk (see the registers section). 3, 13 dgnd digital ground. ground reference point for all digital circuitry on the ad7322. the dgnd and agnd voltages ideally should be at the same potential an d must not be more than 0.3 v apart, even on a transient basis. 4 agnd analog ground. ground reference poi nt for all analog circuitry on th e ad7322. all analog input signals and any external reference signal should be refe rred to this agnd voltage. the agnd and dgnd voltages ideally should be at the same potential an d must not be more than 0.3 v apart, even on a transient basis. 5 refin/out reference input/reference output. the on-chip reference is available on this pin for use external to the ad7322. the nominal internal reference voltage is 2.5 v, which appears at the pin. a 680 nf capacitor should be placed on the reference pin (see the reference section). alternatively, the internal reference can be disabled and an external reference applied to this input. on power-up, the external reference mode is the default condition. 6 v ss negative power supply voltage. this is the nega tive supply voltage for the analog input section. 7, 8 v in 0, v in 1 analog input 0 and analog input 1. the analog inp uts are multiplexed into the on-chip track-and-hold. the analog input channel for conversion is selected by programming the add0 channel address bit in the control register. the inputs can be configured as single-ended, true differential, or pseudo differential (see table 10 ). the configuration of the analog inputs is selected by programming the mode bits, bit mode 1 and bit mode 0, in the control register. the input range on each input channel is controlled by programming the range register. input ranges of 10 v, 5 v, 2.5 v, and 0 v to +10 v can be selected on each analog input channel when a +2 .5 v reference voltage is used (see the registers section). 9 v dd positive power supply voltage. this is the posi tive supply voltage for the analog input section. 10 v cc analog supply voltage, 2.7 v to 5.25 v. this is the supply voltage for the adc core on the ad7322. this supply should be decoupled to agnd. 11 v drive logic power supply input. the voltage supplied at this pin determines at what voltage the interface operates. this pin should be decoupled to dgnd. the voltage at this pin may be different from that at v cc , but it should not exceed v cc by more than 0.3 v. 12 dout serial data output. the conversion o utput data is supplied to this pin as a serial data stream. the bits are clocked out on the falling edge of the sclk inp ut, and 16 sclks are required to access the data. the data stream consists of two leading zero bits, a cha nnel identification bit, the sign bit, and 12 bits of conversion data. the data is provided msb first (see the serial interface section). 14 sclk serial clock, logic input. a serial clock input prov ides the sclk used for accessing the data from the ad7322. this clock is also used as the cl ock source for the conversion process.
ad7322 rev. a | page 9 of 36 typical performance characteristics 1.0 ?1.0 0 8192 code inl error (lsb) 0.8 0.6 0.4 0.2 0 ?0.2 ?0.4 ?0.6 ?0.8 1024 2048 3072 4096 5120 6144 7168 512 1536 2560 3584 4608 5632 6656 7680 04863-007 v cc =v drive =5v t a = 25c v dd ,v ss =15v int/ext 2.5v reference 10v range +inl = +0.55lsb ?inl = ?0.68lsb 0 ?140 0 500 frequency (khz) snr (db) ?20 ?40 ?60 ?80 ?100 ?120 50 100 150 200 250 300 350 400 450 4096 point fft v cc = v drive = 5v v dd , v ss = 15v t a = 25c int/ext 2.5v reference 10v range f in = 50khz snr = 77.30db sinad = 76.85db thd = ?86.96db sfdr = ?88.22db 04863-004 figure 7. typical inl true differential mode figure 4. fft true differential mode 1.0 ?1.0 0 8192 code dnl error (lsb) 0.8 0.6 0.4 0.2 0 ?0.2 ?0.4 ?0.6 ?0.8 1024 2048 3072 4096 5120 6144 7168 512 1536 2560 3584 4608 5632 6656 7680 v cc =v drive =5v t a = 25c v dd ,v ss = 15v int/ext 2.5v reference 10v range +dnl = +0.79lsb ?dnl = ?0.38lsb 04863-043 0 ?140 0 500 frequency (khz) snr (db) ?20 ?40 ?60 ?80 ?100 ?120 50 100 150 200 250 300 350 400 450 4096 point fft v cc = v drive = 5v v dd , v ss = 15v t a = 25c int/ext 2.5v reference 10v range f in = 50khz snr = 74.67db sinad = 74.03db thd = ?82.68db sfdr = ?85.40db 04863-005 figure 5. fft si ngle-ended mode figure 8. typical dnl single-ended mode 1.0 ?1.0 0 8192 code inl error (lsb) 0.8 0.6 0.4 0.2 0 ?0.2 ?0.4 ?0.6 ?0.8 1024 2048 3072 4096 5120 6144 7168 512 1536 2560 3584 4608 5632 6656 7680 v cc =v drive =5v t a = 25c v dd ,v ss =15v int/ext 2.5v reference 10v range +inl = +0.87lsb ?inl = ?0.49lsb 04863-044 1.0 ?1.0 0 8192 code dnl error (lsb) 0.8 0.6 0.4 0.2 0 ?0.2 ?0.4 ?0.6 ?0.8 1024 2048 3072 4096 5120 6144 7168 512 1536 2560 3584 4608 5632 6656 7680 v cc =v drive =5v t a =25c v dd ,v ss =15v int/ext 2.5v reference 10v range +dnl = +0.72lsb ?dnl = ?0.22lsb 04863-006 figure 6. typical dnl true differential mode figure 9. typical in l single-ended mode
ad7322 rev. a | page 10 of 36 ? 50 ?100 10 1000 anal og input frequency (khz) thd (db) 100 ?55 ?60 ?65 ?70 ?75 ?80 ?85 ?90 ?95 2.5v se 2.5v diff 5v diff 5v se 10v se 10v diff 0v to +10v se v cc =5v v dd /v ss = 12v t a = 25c f s =1msps 0v to +10v diff 04863-008 figure 10. thd vs. analog input frequency for single-ended (se) and true differential mode (diff) at 5 v v cc ? 50 ?100 10 1000 anal og input frequency (khz) thd (db) 100 ?55 ?60 ?65 ?70 ?75 ?80 ?85 ?90 ?95 v cc =3v v dd /v ss = 12v t a = 25c f s =1msps 2.5v se 2.5v diff 5v diff 5v se 10v diff 0v to +10v se 10v se 0v to +10v diff 04863-009 figure 11. thd vs. analog input frequency for single-ended (se) and true differential mode (diff) at 3 v v cc 80 50 10 1000 analog input frequency (khz) sinad (db) 100 75 70 65 60 55 v cc =5v v dd /v ss = 12v t a = 25c f s =1msps 2.5v se 2.5v diff 5v diff 10v diff 5v se 0v to +10v se 10v se 0v to +10v diff 04863-010 figure 12. sinad vs. analog input frequency for single-ended (se) and differential mode (diff) at 5 v v cc 80 50 10 1000 analog input frequency (khz) sinad (db) 100 75 70 65 60 55 v cc =3v v dd /v ss = 12v t a = 25c f s =1msps 2.5v se 2.5v diff 5v diff 10v diff 0v to +10v se 10v se 5v se 0v to +10v diff 04863-011 figure 13. sinad vs. analog input frequency for single-ended (se) and differential mode (diff) at 3 v v cc ? 50 ?95 0 600 fr equency of input noise (khz) channel-to-channel isolation (db) ?55 ?60 ?65 ?70 ?75 ?80 ?85 ?90 100 200 300 400 500 v dd /v ss =12v single-ended mode f s =1msps t a = 25c 50khz on selected channel v cc =3v v cc =5v 04863-012 figure 14. channel-to-channel isolation 10k 0 ?2 code number of occurrences 9k 8k 7k 6k 5k 4k 3k 2k 1k ?1 0 1 2 0 228 9469 303 0 v cc =5v v dd /v ss = 12v range = 10v 10k samples t a = 25c 04863-013 figure 15. histogram of codes true differential mode
ad7322 rev. a | page 11 of 36 8k 0 ?3 code number of occurrences 7k 6k 5k 4k 3k 2k 1k ?2 ?1 0 1 2 3 v cc = 5v v dd /v ss = 12v range = 10v 10k samples t a = 25c 023 1201 7600 1165 11 0 04863-014 figure 16. histogram of codes, single-ended mode ? 50 ?100 0 rip ple frequency (khz) cmrr (db) ?55 ?60 ?65 ?70 ?75 ?80 ?85 ?90 ?95 200 400 600 800 1000 1200 differential mode f in = 50khz v dd /v ss = 12v f s = 1msps t a = 25c v cc = 5v v cc = 3v 0 4863-055 figure 17. cmrr vs. common-mode ripple frequency 2.0 ?2.0 v dd /v ss supply voltage (v) dnl error (lsb) 1.5 1.0 0.5 0 ?0.5 ?1.0 ?1.5 5 7 9 11 13 15 17 19 5v range v cc =v drive =5v internal reference single-ended mode dnl = 750ksps dnl = 750ksps dnl = 500ksps dnl = 500ksps dnl = 1msps dnl = 1msps 04863-049 figure 18. dnl error vs. supply voltage at 500 ksps, 750 ksps, and 1 msps 2.0 ?2.0 v dd /v ss supply voltage (v) inl error (lsb) 1.5 1.0 0.5 0 ?0.5 ?1.0 ?1.5 5 7 9 11 13 15 17 19 5v range v cc =v drive =5v internal reference single-ended mode inl = 750ksps inl = 500ksps inl = 1msps inl = 750ksps inl = 500ksps inl = 1msps 04863-050 figure 19. inl error vs. supply voltage at 500 ksps, 750 ksps, and 1 msps ? 50 ?100 0 1200 su pply ripple frequency (khz) psrr (db) ?55 ?60 ?65 ?70 ?75 ?80 ?85 ?90 ?95 200 400 600 800 1000 100mv p-p sine wave on each supply no decoupling single-ended mode f s =1msps v cc =5v v cc =3v v dd =12v v ss =?12v 04863-054 figure 20. psrr vs. supply ripple frequency without supply decoupling 10 1000 analog input frequency (khz) thd (db) 100 ? 50 ?55 ?60 ?65 ?70 ?75 ?80 ?85 ?90 ?95 v cc =v drive =5v v dd /v ss = 12v t a =25c internal reference range = 10v and 2.5v r in =50 ? , 2.5v range r in =50 ? , 10v range r in =100 ? , 2.5v range r in =1000 ? , 2.5v range r in =2000 ? , 2.5v range r in =4700 ? , 2.5v range r in = 2000 ? , 10v range r in = 1000 ? , 10v range r in = 100 ? , 10v range 04863-015 figure 21. thd vs. analog input frequency for various source impedances, true differential mode
ad7322 rev. a | page 12 of 36 10 1000 input frequency (khz) thd (db) 100 ? 50 ?55 ?60 ?65 ?70 ?75 ?80 ?85 ?90 ?95 v cc =v drive =5v v dd /v ss = 12v t a =25c internal reference range = 10v and 2.5v r in = 2000 ? , 10v range r in = 1000 ? , 10v range r in =50 ? , 2.5v range r in = 100 ? , 10v range r in = 100 ? , 2.5v range r in = 1000 ? , 2.5v range r in = 2000 ? , 2.5v range r in =50 ? , 10v range 04863-016 figure 22. thd vs. analog input frequency for various source impedances, single-ended mode
ad7322 rev. a | page 13 of 3 6 terminology differential nonlinearity this is the difference between the measured and the ideal 1 lsb change between any two adjacent codes in the adc. integral nonlinearity this is the maximum deviation from a straight line passing through the endpoints of the adc transfer function. the endpoints of the transfer function are zero scale (a point 1 lsb below the first code transition) and full scale (a point 1 lsb above the last code transition). offset code error this applies to straight binary output coding. it is the deviation of the first code transition (00000) to (00001) from the ideal, that is, agnd + 1 lsb. offset error match this is the difference in offset error between any two input channels. gain error this applies to straight binary output coding. it is the deviation of the last code transition (111110) to (111111) from the ideal (that is, 4 v ref ? 1 lsb, 2 v ref ? 1 lsb, v ref ? 1 lsb) after adjusting for the offset error. gain error match this is the difference in gain error between any two input channels. bipolar zero code error this applies when using twos complement output coding and a bipolar analog input. it is the deviation of the midscale transi- tion (all 1s to all 0s) from the ideal input voltage, that is, agnd ? 1 lsb. bipolar zero code error match this refers to the difference in bipolar zero code error between any two input channels. positive full-scale error this applies when using twos complement output coding and any of the bipolar analog input ranges. it is the deviation of the last code transition (011110) to (011111) from the ideal (4 v ref ? 1 lsb, 2 v ref ? 1 lsb, v ref ? 1 lsb) after adjust- ing for the bipolar zero code error. positive full-scale error match this is the difference in positive full-scale error between any two input channels. negative full-scale error this applies when using twos complement output coding and any of the bipolar analog input ranges. this is the deviation of the first code transition (10000) to (10001) from the ideal (that is, ?4 v ref + 1 lsb, ?2 v ref + 1 lsb, ?v ref + 1 lsb) after adjusting for the bipolar zero code error. negative full-scale error match this is the difference in negative full-scale error between any two input channels. track-and-hold acquisition time the track-and-hold amplifier returns into track mode after the 14 th sclk rising edge. track-and-hold acquisition time is the time required for the output of the track-and-hold amplifier to reach its final value, within 1/2 lsb, after the end of a conversion. for the 2.5 v range, the specified acquisition time is the time required for the track-and-hold amplifier to settle to within 1 lsb. signal-to-(noise + distortion) ratio this is the measured ratio of signal-to-(noise + distortion) at the output of the adc. the signal is the rms amplitude of the fundamental. noise is the sum of all nonfundamental signals up to half the sampling frequency (f s /2), excluding dc. the ratio is dependent on the number of quantization levels in the digi- tization process. the more levels there are, the smaller the quantization noise becomes. theoretically, the signal-to-(noise + distortion) ratio for an ideal n-bit converter with a sine wave input is given by signal-to -( noise + distortion ) = (6.02 n + 1.76) db for a 13-bit converter, this is 80.02 db. total harmonic distortion total harmonic distortion (thd) is the ratio of the rms sum of harmonics to the fundamental. for the ad7322, it is defined as 1 2 6 2 5 2 4 2 3 2 2 log20)db( v vvvvv thd ++++ = where v 1 is the rms amplitude of the fundamental, and v 2 , v 3 , v 4 , v 5 , and v 6 are the rms amplitudes of the second through the sixth harmonics. peak harmonic or spurious noise peak harmonic or spurious noise is defined as the ratio of the rms value of the next largest component in the adc output spectrum (up to f s /2, excluding dc) to the rms value of the fundamental. normally, the value of this specification is deter- mined by the largest harmonic in the spectrum, but for adcs where the harmonics are buried in the noise floor, the largest harmonic can be a noise peak.
ad7322 rev. a | page 14 of 36 channel-to-channel isolation channel-to-channel isolation is a measure of the level of crosstalk between any two channels. it is measured by applying a full-scale, 100 khz sine wave signal to all unselected input channels and determining the degree to which the signal attenuates in the selected channel with a 50 khz signal. figure 14 shows the worst- case across all eight channels for the ad7322. the analog input range is programmed to be the same on all channels. intermodulation distortion with inputs consisting of sine waves at two frequencies, fa and fb, any active device with nonlinearities creates distortion products at the sum and difference frequencies of mfa nfb, where m, n = 0, 1, 2, 3, and so on. intermodulation distortion terms are those for which neither m nor n are equal to 0. for example, the second-order terms include (fa + fb) and (fa ? fb), whereas the third-order terms incl ude (2fa + fb), (2fa ? fb), (fa + 2fb), and (fa ? 2fb). the ad7322 is tested using the ccif standard where two input frequencies near the top end of the input bandwidth are used. in this case, the second-order terms are usually distanced in frequency from the original sine waves, whereas the third-order terms are usually at a frequency close to the input frequencies. as a result, the second- and third-order terms are specified separately. the calculation of the intermodulation distortion is per the thd specification, where it is the ratio of the rms sum of the individual distortion products to the rms amplitude of the sum of the fundamentals, expressed in decibels. psr (power supply rejection) variations in power supply affect the full-scale transition but not the linearity of the converter. power supply rejection is the maximum change in the full-scale transition point due to a change in power supply voltage from the nominal value (see the typical performance characteristics section). cmrr (common-mode rejection ratio) cmrr is defined as the ratio of the power in the adc output at full-scale frequency, f, to the power of a 100 mv sine wave applied to the common-mode voltage of the v in + and v in ? frequency, f s , as cmrr (db) = 10 log ( pf / pf s ) where pf is the power at frequency f in the adc output, and pf s is the power at frequency f s in the adc output (see figure 17 ).
ad7322 rev. a | page 15 of 36 theory of operation circuit information the ad7322 is a fast, 2-channel, 12-bit plus sign, bipolar input, serial adc. the ad7322 can accept bipolar input ranges that include 10 v, 5 v, and 2.5 v; it can also accept a 0 v to +10 v unipolar input range. a different analog input range can be programmed on each analog input channel via the on-chip registers. the ad7322 has a high speed serial interface that can operate at throughput rates up to 1 msps. the ad7322 requires v dd and v ss dual supplies for the high voltage analog input structures. these supplies must be equal to or greater than the analog input range. see table 6 for the requirements of these supplies for each analog input range. the ad7322 requires a low voltage 2.7 v to 5.25 v v cc supply to power the adc core. table 6. reference and supply requirements for each analog input range selected analog input range (v) reference voltage (v) full-scale input range (v) v cc (v) minimum v dd /v ss (v) 10 2.5 10 3/5 10 3.0 12 3/5 12 5 2.5 5 3/5 5 3.0 6 3/5 6 2.5 2.5 2.5 3/5 5 3.0 3 3/5 5 0 to +10 2.5 0 to +10 3/5 +10/agnd 3.0 0 to +12 3/5 +12/agnd to meet the specified performance when the ad7322 is confi- gured with the minimum v dd and v ss supplies for a chosen analog input range, the throughput rate should be decreased from the maximum throughput range (see the typical performance characteristics section). figure 18 and figure 19 show the change in inl and dnl as the v dd and v ss voltages are varied. when operating at the maximum throughput rate, as the v dd and v ss supply voltages are reduced, the inl and dnl error increases. however, as the throughput rate is reduced with the minimum v dd and v ss supplies, the inl and dnl error is reduced. figure 31 shows the change in thd as the v dd and v ss supplies are reduced. at the maximum throughput rate, the thd degrades significantly as v dd and v ss are reduced. it is therefore necessary to reduce the throughput rate when using minimum v dd and v ss supplies so that there is less degradation of thd and the specified performance can be maintained. the degradation is due to an increase in the on resistance of the input multiplexer when the v dd and v ss supplies are reduced. the analog inputs can be configured as two single-ended inputs, one true differential input, or one pseudo differential input. selection can be made by programming the mode bits, mode 0 and mode 1, in the control register. the serial clock input accesses data from the part and provides the clock source for the successive approximation adc. the ad7322 has an on-chip 2.5 v reference. however, the ad7322 can also work with an external reference. on power-up, the exter- nal reference operation is the default option. if the internal reference is the preferred option, the user must write to the reference bit in the control register to select the internal refer- ence operation. the ad7322 also features power-down options to allow power saving between conversions. the power-down modes are selected by programming the on-chip control register as described in the modes of operation section. converter operation the ad7322 is a successive approximation adc built around two capacitive dacs. figure 23 and figure 24 show simplified schematics of the adc in single-ended mode during the acquisition and conversion phases, respectively. figure 25 and figure 26 show simplified schematics of the adc in differential mode during acquisition and conversion phase, respectively. the adc is composed of control logic, a sar, and capacitive dacs. in figure 23 (the acquisition phase), sw2 is closed and sw1 is in position a, the comparator is held in a balanced condition, and the sampling capacitor array acquires the signal on the input. capacitive dac control logic comparator agnd sw2 sw1 a b c s v in 0 04863-017 figure 23. adc acquisition phase (single-ended) when the adc starts a conversion (see figure 24 ), sw2 opens and sw1 moves to position b, causing the comparator to become unbalanced. the control logic and the charge redistribution dac are used to add and subtract fixed amounts of charge from the capacitive dac to bring the comparator back into a balanced condition. when the comparator is rebalanced, the conversion is complete. the control logic generates the adc output code. capacitive dac control logic comparator agnd sw2 sw1 a b c s v in 0 0 4863-018 figure 24. adc conversion phase (single-ended)
ad7322 rev. a | page 16 of 36 figure 25 shows the differential configuration during the acquisition phase. for the conversion phase, sw3 opens and sw1 and sw2 move to position b (see figure 26 ). the output impedances of the source driving the v in + and v in ? pins must be matched; otherwise, the two inputs will have different settling times, resulting in errors. 0 4863-019 capacitive dac control logic capacitive dac comparator sw3 sw1 a b c s c s v in + sw2 a b v in ? v ref notes 1. v in + refers to v in 0 and v in ? refers to v in 1. figure 25. adc differential configuration during acquisition phase capacitive dac control logic capacitive dac comparator sw3 sw1 a b c s c s v in + sw2 a b v in ? v ref 04863-020 notes 1. v in + refers to v in 0 and v in ? refers to v in 1. figure 26. adc differential configuration during conversion phase output coding the ad7322 default output coding is set to twos complement. the output coding is controlled by the coding bit in the control register. to change the output coding to straight binary coding, the coding bit in the control register must be set. when operat- ing in sequence mode, the output coding for each channel in the sequence is the value written to the coding bit during the last write to the control register. transfer functions the designed code transitions occur at successive integer lsb values (that is, 1 lsb, 2 lsb, and so on). the lsb size is dependent on the analog input range selected. table 7. lsb sizes for each analog input range input range full-scale range/8192 codes lsb size 10 v 20 v 2.441 mv 5 v 10 v 1.22 mv 2.5 v 5 v 0.61 mv 0 v to +10 v 10 v 1.22 mv the ideal transfer characteristic for the ad7322 when twos complement coding is selected is shown in figure 27 . the ideal transfer characteristic for the ad7322 when straight binary coding is selected is shown in figure 28 . 011...111 011...110 000...001 000...000 111...111 ?fsr/2 + 1lsb agnd + 1lsb +fsr/2 ? 1lsb bipolar ranges +fsr ? 1lsb unipolar range agnd ? 1lsb analog input adc code 100...010 100...001 100...000 04863-021 figure 27. twos complement transfer characteristic (bipolar ranges) 111...111 111...110 111...000 011...111 ?fsr/2 + 1lsb agnd + 1lsb +fsr/2 ? 1lsb bipolar ranges +fsr ? 1lsb unipolar range analog input adc code 000...010 000...001 000...000 04863-022 figure 28. straight binary transfer characteristic (bipolar ranges) analog input structure the analog inputs of the ad7322 can be configured as single- ended, true differential, or pseudo differential via the control register mode bits (see table 10 ). the ad7322 can accept true bipolar input signals. on power-up, the analog inputs operate as two single-ended analog input channels. if true differential or pseudo differential is required, a write to the control register is necessary after power-up to change this configuration. figure 29 shows the equivalent analog input circuit of the ad7322 in single-ended mode. figure 30 shows the equivalent analog input structure in differential mode. the two diodes provide esd protection for the analog inputs. d d v dd c2 r1 v in 0 v ss c1 04863-023 figure 29. equivalent analog input circuit (single-ended)
ad7322 rev. a | page 17 of 36 d d v dd c2 r1 v in + v ss c1 d d v dd c2 r1 v in ? v ss c1 04863-024 notes 1. v in + refers to v in 0 and v in ? refers to v in 1. figure 30. equivalent analog input circuit (differential) care should be taken to ensure that the analog input does not exceed the v dd and v ss supply rails by more than 300 mv. exceeding this value causes the diodes to become forward biased and to start conducting into either the v dd supply rail or v ss supply rail. these diodes can conduct up to 10 ma without causing irreversible damage to the part. in figure 29 and figure 30 , capacitor c1 is typically 4 pf and can primarily be attributed to pin capacitance. resistor r1 is a lumped component made up of the on resistance of the input multiplexer and the track-and-hold switch. capacitor c2 is the sampling capacitor; its capacitance varies depending on the analog input range selected (see the specifications section). track-and-hold section the track-and-hold on the analog input of the ad7322 allows the adc to accurately convert an input sine wave of full-scale amplitude to 13-bit accuracy. the input bandwidth of the track- and-hold is greater than the nyquist rate of the adc. the ad7322 can handle frequencies up to 22 mhz. the track-and-hold enters its tracking mode on the 14 th sclk rising edge after the cs falling edge. the time required to acquire an input signal depends on how quickly the sampling capacitor is charged. with zero source impedance, 305 ns is sufficient to acquire the signal to the 13-bit level. the acquisition time required is calculated using the following formula: t acq = 10 (( r source + r ) c ) where c is the sampling capacitance and r is the resistance seen by the track-and-hold amplifier looking back on the input. for the ad7322, the value of r includes the on resistance of the input multiplexer and is typically 300 . r source should include any extra source impedance on the analog input. the ad7322 enters track mode on the 14 th sclk rising edge. when running the ad7322 at a throughput rate of 1 msps with a 20 mhz sclk signal, the adc has approximately 1.5 sclk + t 8 + t quiet to acquire the analog input signal. the adc goes back into hold mode on the cs falling edge. as the v dd /v ss supply voltage is reduced, the on resistance of the input multiplexer increases. therefore, based on the equation for t acq , it is necessary to increase the amount of acquisition time provided to the ad7322 and, therefore, decrease the overall throughput rate. figure 31 shows that if the throughput rate is reduced when operating with minimum v dd and v ss supplies, the specified thd performance is maintained. ? 50 ?95 51 v dd /v ss supplies (v) thd (db) 9 ?55 ?60 ?65 ?70 ?75 ?80 ?85 ?90 7 9 11 13 15 17 500ksps 750ksps 1msps v cc = v drive = 5v internal reference t a = 25c f in = 10khz 5v range se mode 0 4863-051 figure 31. thd vs. v dd /v ss supply voltage at 500 ksps, 750 ksps, and 1 msps unlike other bipolar adcs, the ad7322 does not have a resistive analog input structure. on the ad7322, the bipolar analog signal is sampled directly onto the sampling capacitor. this gives the ad7322 high analog input impedance. an approximation for the analog input impedance can be calculated from the following formula: z = 1/(f s c s ) where f s is the sampling frequency, and c s is the sampling capacitor value. c s depends on the analog input range chosen (see the specifications section). when operating at 1 msps, the analog input impedance is typically 75 k for the 10 v range. as the sampling frequency is reduced, the analog input impedance further increases. as the analog input impedance increases, the current required to drive the analog input therefore decreases.
ad7322 rev. a | page 18 of 36 typical connection diagram figure 32 shows a typical connection diagram for the ad7322. in this configuration, the agnd pin is connected to the analog ground plane of the system, and the dgnd pin is connected to the digital ground plane of the system. the analog inputs on the ad7322 can be configured to operate in single-ended, true differential, or pseudo differential mode. the ad7322 can operate with either an internal or external reference. in figure 32, the ad7322 is configured to operate with the internal 2.5 v reference. a 680 nf decoupling capacitor is required when operating with the internal reference. the v cc pin can be connected to either a 3 v supply voltage or a 5 v supply voltage. v dd and v ss are the dual supplies for the high voltage analog input structures. the voltage on these pins must be equal to or greater than the highest analog input range selected on the analog input channels (see table 6). the v drive pin is connected to the supply voltage of the microprocessor. the voltage applied to the v drive input controls the voltage of the serial interface. v drive can be set to 3 v or 5 v. ad7322 v cc v dd 1 serial interface c/p v in 0 v in 1 refin/out cs dout v drive sclk din dgnd 10f 0.1f + 10f 0.1f + 10f 0.1f + analog inputs 10v, 5v, 2.5v 0v to +10v +15 v ?15v 680nf v ss 1 v cc +2.7 v to +5.25 v 1 minimum v dd and v ss supply voltages depend on the highest analog input range selected. agnd 10f 0.1f + +3v supply 04863-025 figure 32. typical connection diagram analog input single-ended inputs the ad7322 has a total of two analog inputs when operating in single-ended mode. each analog input can be independently programmed to one of the four analog input ranges. in applications where the signal source is high impedance, it is recommended to buffer the signal before applying it to the adc analog inputs. figure 33 shows the configuration of the ad7322 in single- ended mode. ad7322 1 v in 0 v + v? v dd v ss v cc 5v agnd 1 additional pins omitted for clarity. 04863-026 figure 33. single-ended mode typical connection diagram true differential mode the ad7322 can have a total of one true differential analog input pair. differential signals have some benefits over single- ended signals, including better noise immunity based on the devices common-mode rejection and improvements in distortion performance. figure 34 defines the configuration of the true differential analog inputs of the ad7322. 04863-027 ad7322 1 v in + v in ? 1 additional pins omitted for clarity. notes 1. v in + refers to v in 0 and v in ? refers to v in 1. figure 34. true differential inputs the amplitude of the differential signal is the difference between the signals applied to the v in + and v in ? inputs in each differential pair (v in + ? v in ?). v in + and v in ? should be simultaneously driven by two signals of equal amplitude, dependent on the input range selected, that are 180 out of phase. assuming the 4 v ref mode, the amplitude of the differential signal is ?20 v to +20 v p-p (2 4 v ref ), regardless of the common mode. the common mode is the average of the two signals (v in + + v in ?)/2 and is therefore the voltage on which the two input signals are centered. this voltage is set up externally, and its range varies with reference voltage. as the reference voltage increases, the common-mode range decreases. when driving the differential inputs with an amplifier, the actual common-mode range is determined by the amplifiers output swing. if the differential inputs are not driven from an amplifier, the common-mode range is determined by the supply voltage on the v dd supply pin and the v ss supply pin.
ad7322 rev. a | page 19 of 36 when a conversion takes place, the common mode is rejected, resulting in a noise-free signal of amplitude ?2 (4 v ref ) to +2 (4 v ref ), corresponding to digital code ?4096 to digital code +4095. 16.5v v dd /v ss 12v v dd /v ss 5 ?6 v com range (v) 4 3 2 1 0 ?1 ?2 ?3 ?4 ?5 v cc =3v v ref =3v 2.5v range 10v range 5v range 2.5v range 5v range 10v range 04863-045 figure 35. common-mode range for v cc = 3 v and refin/out = 3 v 16.5v v dd /v ss 12v v dd /v ss v com range (v) v cc =5v v ref =3v 8 ?4 6 4 2 0 ?2 2.5v range 10v range 5v range 2.5v range 5v range 10v range 04863-046 figure 36. common-mode range for v cc = 5 v and refin/out = 3 v 6 ?8 4 2 0 ?2 ?4 ?6 16.5v v dd /v ss 12v v dd /v ss v com range (v) v cc =3v v ref =2.5v 2.5v range 10v range 5v range 2.5v range 5v range 10v range 04863-047 figure 37. common-mode range for v cc = 3 v and refin/out = 2.5 v 8 ?8 6 4 2 0 ?2 ?4 ?6 16.5v v dd /v ss 12v v dd /v ss v com range (v) v cc =5v v ref =2.5v 2.5v range 10v range 5v range 2.5v range 5v range 10v range 04863-048 figure 38. common-mode range for v cc = 5 v and refin/out = 2.5 v pseudo differential inputs the ad7322 can have one pseudo differential pair. the v in + input is coupled to the signal source and must have an amplitude within the selected range for that channel as programmed in the range register. a dc input is applied to the v in ? input. the voltage applied to this input provides an offset for the v in + input from ground or a pseudo ground. pseudo differential inputs separate the analog input signal ground from the adc ground, allowing cancellation of dc common-mode voltages. figure 39 shows the ad7322 configured in pseudo differential mode. when a conversion takes place, the pseudo ground corresponds to code ?4096 and the maximum amplitude corresponds to code +4095. ad7322 1 v in + v + v? v dd v ss v cc 5 v v in ? 0 4863-028 1 additional pins omitted for clarity. notes 1. v in + refers to v in 0 and v in ? refers to v in 1. figure 39. pseudo differential inputs figure 40 and figure 41 show the typical voltage range on the v in ? input for the different analog input ranges when configured in the pseudo differential mode. for example, when the ad7322 is configured to operate in pseudo differential mode and the 5 v range is selected with 16.5 v v dd /v ss supplies and 5 v v cc , the voltage on the v in ? input can vary from ?6.5 v to +6.5 v.
ad7322 rev. a | page 20 of 36 8 ?8 6 4 2 0 ?2 ?4 ?6 2.5v range 10v range 10v range 5v range 2.5v range 5v range 0v to +10v range 0v to +10v range 16.5v v dd /v ss 12v v dd /v ss 04863-039 v cc = 5v v ref = 2.5v pseudo input voltage range (v) figure 40. pseudo input range with v cc = 5 v 2.5v range 10v range 10v range 5v range 2.5v range 5v range 0v to +10v range 0v to +10v range 16.5v v dd /v ss 12v v dd /v ss 4 ?8 2 0 ?2 ?4 ?6 04863-040 v cc = 3v v ref = 2.5v pseudo input voltage range (v) figure 41. pseudo input range with v cc = 3 v driver amplifier choice in applications where the harmonic distortion and signal-to- noise ratio are critical specifications, the analog input of the ad7322 should be driven from a low impedance source. large source impedances significantly affect the ac performance of the adc and can necessitate the use of an input buffer amplifier. when no amplifier is used to drive the analog input, the source impedance should be limited to low values. the maximum source impedance depends on the amount of thd that can be tolerated in the application. the thd increases as the source impedance increases and performance degrades. figure 21 and figure 22 show graphs of the thd vs. the analog input frequency for various source impedances. depending on the input range and analog input configuration selected, the ad7322 can handle source impedances of up to 4.7 k before the thd starts to degrade. due to the programmable nature of the analog inputs on the ad7322, the choice of op amp used to drive the inputs is a function of the particular application and depends on the input configuration and the analog input voltage ranges selected. the driver amplifier must be able to settle for a full-scale step to a 13-bit level, 0.0122%, in less than the specified acquisition time of the ad7322. an op amp such as the ad8021 meets this requirement when operating in single-ended mode. the ad8021 needs an external compensating npo type of capacitor. the ad8022 can also be used in high frequency applications where a dual version is required. for lower frequency applications, op amps such as the ad797, ad845 , and the ad8610 can be used in the ad7322 single- ended mode configuration. differential operation requires that v in + and the v in ? be simulta- neously driven with two signals of equal amplitude that are 180 out of phase. the common mode must be set up externally to the ad7322. the common-mode range is determined by the refin/ out voltage, the v cc supply voltage, and the particular amplifier used to drive the analog inputs. differential mode with either an ac input or a dc input provides the best thd performance over a wide frequency range. because not all applications have a signal preconditioned for differential operation, there is often a need to perform the single-ended-to-differential conversion. this single-ended-to-differential conversion can be performed using an op amp pair. typical connection diagrams for an op amp pair are shown in figure 42 and figure 43 . in figure 42 the common-mode signal is applied to the noninverting input of the second amplifier. v in v+ v? 3k? 1.5k ? 1.5k ? 1.5k ? 1.5k ? 10k ? 20k? v com 04863-029 figure 42. single-ended-to-differential configuration with the ad845 v in v+ v? 442 ? 442 ? 442 ? 442 ? 442 ? 100 ? ad8021 ad8021 442 ? 04863-030 figure 43. single-ended-to-differential configuration with the ad8021
ad7322 rev. a | page 21 of 36 registers the ad7322 has two programmable registers, the control register and the range register. these registers are write-only registers. addressing registers a serial transfer on the ad7322 consists of 16 sclk cycles. the three msbs on the din line during the 16 sclk transfer are decoded to determine which register is addressed. the three msbs consist of the write bit, zero bit, and register select bit. the register select bit is used to determine which of the two on- board registers is selected. the write bit determines if the data on the din line following the register select bit loads into the addressed register. if the write bit is 1, the bits are loaded into the register addressed by the register select bits. if the write bit is 0, the data on the din line does not load into any register. the zero bit must always be set to 0. table 8. decoding register select bit and write bit write zero register select comment 0 0 x data on the din line during this serial transf er is ignored. register co ntents remain unchanged. 1 0 0 this combination selects the control register. the subsequent 12 bits are loaded into the control register. 1 0 1 this combination selects the range register. the su bsequent six bits are loaded into the range register.
ad7322 rev. a | page 22 of 36 control register the control register is used to select the analog input channel, analog input configuration, reference, coding, and power mode. the control register is a write-only, 12-bit register. data loaded on the din line corresponds to the ad7322 configuration for the next conversion. data should be loaded into the control register after the range register has been initialized. the bit functions of the control register are shown in table 9 (the power-up status of all bits is 0). the two analog input channels can be configured as one pseudo differential analog input, one true differential input, or two single-ended analog inputs (see table 10). msb lsb 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 write zero register select zero zero add0 mode 1 mode 0 pm1 pm0 coding ref seq1 seq2 zero 0 table 9. control register details bit mnemonic description 12, 11, 1 zero these bits should contain 0 during each write to the control register. 10 add0 this channel address bit is used to select the analog input channel for the next conversion if the sequencer is not being used. if the sequencer is being used, this channel address bit is used to select the final channel in the consecutive sequence (see table 10). 9, 8 mode 1, mode 0 these two mode bits are used to select the configuration of the two analog input pins, v in 0 and v in 1. these bits are used in conjunction with the channel address bit. on the ad7322, the analog inputs can be configured as single-ended inputs, true differential inputs, or pseudo differential inputs (see table 10). 7, 6 pm1, pm0 the power management bits are used to sele ct different power mode options on the ad7322 (see table 11). 5 coding this bit is used to select the ty pe of output coding the ad7322 uses for the next conversion result. if coding = 0, the output coding is twos complement. if coding = 1, the output coding is straight binary. when operating in sequence mode, the output coding fo r each channel is the value written to the coding bit during the last write to the control register. 4 ref the reference bit is used to enable or disable the internal reference. if ref = 0, the external reference is enabled and used for the next conversion, and the internal reference is disabled. if ref = 1, the internal reference is used for the next conversion. when operating in sequence mode, the reference used for each channel is the value written to the ref bit during the last write to the control register. 3, 2 seq1, seq2 the sequence 1 and sequence 2 bits are us ed to control the operation of the sequencer (see table 12). table 10. analog input configuration selection mode 1 = 1, mode 0 = 0 mode 1 = 0, mode 0 =1 mode 1 = 0, mode 0 = 0 channel address bit mode 1 = 1, mode 0 = 1 1 fully differenti al input 1 pseudo differential input 2 single-ended inputs add0 v in + v in ? v in + v in ? v in + v in ? v in + v in ? 0 not allowed v in 0 v in 1 v in 0 v in 1 v in 0 agnd 1 not allowed v in 0 v in 1 v in 0 v in 1 v in 1 agnd
ad7322 rev. a | page 23 of 3 6 table 11. power mode selection pm1 pm0 description 1 1 full shutdown mode. in this mode, all internal circuitry on the ad7322 is powered down. information in the control register is retained when the ad7322 is in full shutdown mode. 1 0 autoshutdown mode. the ad7322 en ters autoshutdown on the 15 th sclk rising edge when the control register is updated. all internal circuitry is powered down in autoshutdown. 0 1 autostandby mode. in this mode, all internal circuitry is powered down excluding the internal reference. the ad7322 enters autostandby mode on the 15 th sclk rising edge after the control register is updated. 0 0 normal mode. all internal circui try is powered up at all times. table 12. sequencer selection seq1 seq2 sequence type 0 x the channel sequencer is not used. the analog channel, sele cted by programming the add0 bit in the control register, selects the next channel for conversion. 1 0 this configuration is used in conjunction with the channel address bit in the control register. this allows continuous conversions on a consecutive sequence of channels, from channel 0 up to channel 1, as selected by the channel address bits in the control register. the range for each channel defaul ts to the ranges previously written into the range register. 1 1 the channel sequencer is not used. the analog channel, sele cted by programming the add0 bit in the control register, selects the next channel for conversion.
ad7322 rev. a | page 24 of 36 range register the range register is used to select one analog input range per analog input channel. this register is a 6-bit, write-only register with two dedicated range bits for each of the analog input channels, channel 0 and channel 1. there are four analog input ranges, 10 v, 5 v, 2.5 v, and 0 v to +10 v. a write to the range register is selected by setting the write bit to 1 and the register select bit to 1. after the initial write to the range register occurs, each time an analog input is selected, the ad7322 automatically configures the analog input to the appropriate range, as indicated by the range register. the 10 v input range is selected by default on each analog input channel (see table 13 ). msb lsb 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 write zero register select v in 0a v in 0b 0 0 v in 1a v in 1b 0 0 0 0 0 0 0 table 13. range selection v in xa v in xb description 0 0 this combination selects the 10 v input range on v in x. 0 1 this combination selects the 5 v input range on v in x. 1 0 this combination selects the 2.5 v input range on v in x. 1 1 this combination selects the 0 v to +10 v input range on v in x.
ad7322 rev. a | page 25 of 36 sequencer operation the ad7322 can be configured to convert a sequence of consecutive channels (see figure 44 ). this sequence begins by converting on channel 0 and ends with a final channel selected by bit add0 in the control register. to operate the ad7322 in this mode, set seq1 to 1 and seq2 to 0, and then select the final channel in the sequence by programming bit add0 in the control register. when the control register is configured to operate the ad7322 in this mode, the din line can be held low, or the write bit can be set to 0. to return to traditional multichannel operation, a write to the control register to set seq1 to 0 and seq2 to 0 is necessary. when seq1 and seq2 are both set to 0, or when both are set to 1, the ad7322 is configured to operate in traditional multichannel mode, where a write to channel address bit add0 in the control register selects the next channel for conversion. 04863-032 din: write to range register to select the range for the analog input channels. dout: conversion result from channel 0, 10v range, single-ended mode. cs din: write bit = 0 or din line held low to continue through sequence of consecutive channels. dout: conversion result from channel1, range as selected in range register. cs din: write bit = 0 or din line held low to continue to convert through the sequence of consecutive channels. dout: conversion result from channel 0, range as selected in range register. cs din: write to control register to select the final channel in the consecutive sequence, set seq1 = 1 and seq2 = 0. select output coding for sequence. dout: conversion result from channel 0, range selected in range register 1, single-ended mode. cs power on. din tied low/write bit = 0. continuously convert on consecutive sequence of channels. din: write to control register to stop the sequence, seq1 = 0, seq2 = 0. dout: conversion result from channel in sequence. cs stopping a sequence. figure 44. flowchart for consecutive sequence of channels
ad7322 rev. a | page 26 of 36 reference the ad7322 can operate with either the internal 2.5 v on-chip reference or an externally applied reference. the internal reference is selected by setting the ref bit in the control register to 1. on power-up, the ref bit is 0, resulting in the selection of the external reference for the ad7322 conversion. suitable reference sources for the ad7322 include ad780, ad1582, adr431 , ref193, and adr391 . the internal reference circuitry consists of a 2.5 v band gap reference and a reference buffer. when operating the ad7322 in internal reference mode, the 2.5 v internal reference is available at the refin/out pin, which should be decoupled to agnd using a 680 nf capacitor. it is recommended that the internal reference be buffered before applying it elsewhere in the system. the internal reference is capable of sourcing up to 90 a. on power-up, if the internal reference operation is required for the adc conversion, a write to the control register is necessary to set the ref bit to 1. during the control register write, the conversion result from the first initial conversion is invalid. the reference buffer requires 500 s to power up and charge the 680 nf decoupling capacitor during the power-up time. the ad7322 is specified for a 2.5 v to 3 v reference range. when a 3 v reference is selected, the ranges are 12 v, 6 v, 3 v, and 0 v to +12 v. for these ranges, the v dd and v ss supply must be equal to or greater than the maximum analog input range selected (see tabl e 6 ). v drive the ad7322 has a v drive feature to control the voltage at which the serial interface operates. v drive allows the adc to easily interface to both 3 v and 5 v processors. for example, if the ad7322 is operated with a v cc of 5 v, the v drive pin can be powered from a 3 v supply. this allows the ad7322 to accept large bipolar input signals with low voltage digital processing.
ad7322 rev. a | page 27 of 36 modes of operation the ad7322 has several modes of operation that are designed to provide flexible power management options. these options can be chosen to optimize the power dissipation/throughput rate ratio for different application requirements. the mode of operation of the ad7322 is controlled by the power manage- ment bits, bit pm1 and bit pm0, in the control register as shown in table 11 . the default mode is normal mode, in which all internal circuitry is fully powered up. normal mode (pm1 = pm0 = 0) this mode is intended for the fastest throughput rate perfor- mance, with the ad7322 being fully powered up at all times. figure 45 shows the general operation of the ad7322 in normal mode. the conversion is initiated on the falling edge of cs , and the track-and-hold enters hold mode as described in the section. data on the din line during the 16 sclk transfer is loaded into one of the on-chip registers if the write bit is set. the register is selected by programming the register select bits (see ). serial interface figure 45 11 6 2 leading zeros, channel i.d. bit, sign bit + conversion result data into control/range register sclk cs dout din 0 4863-035 figure 45. normal mode the ad7322 remains fully powered up at the end of the conversion if both pm1 and pm0 contain 0 in the control register. to complete the conversion and access the conversion result, 16 serial clock cycles are required. at the end of the conversion, cs can idle either high or low until the next conversion. when the data transfer is complete, another conversion can be initiated after the quiet time, t quiet , has elapsed. full shutdown mode (pm1 = pm0 = 1) in this mode, all internal circuitry on the ad7322 is powered down. the part retains information in the registers during full shutdown. the ad7322 remains in full shutdown mode until the power management bits, bit pm1 and bit pm0, in the control register are changed. a write to the control register with pm1 = 1 and pm0 = 1 places the part into full shutdown mode. the ad7322 enters full shut- down mode on the 15 th sclk rising edge when the control register is updated. if a write to the control register occurs while the part is in full shutdown mode with the power management bits, bit pm1 and bit pm0, set to 0 (normal mode), the part begins to power up on the 15 th sclk rising edge when the control register is updated. figure 46 shows how the ad7322 is configured to exit full shutdown mode. to ensure the ad7322 is fully powered up, t power-up for full shutdown mode should elapse before the next cs falling edge. cs 11 6 1 sclk sdata din 1 6 invalid data channel identifier bits + conversion result data into control register data into control register t power-up the p ar tisfullypoweredup once t power-up has elapsed control register is loaded on the first 15 clocks, pm1 = 0, pm0 = 0 to keep the part in normal mode, load pm1 = pm0 = 0 in control register part is in full shutdown part begins to power up on the 15th sclk rising edge as pm1 = pm0 = 0 04863-041 figure 46. exiting full shutdown mode
ad7322 rev. a | page 28 of 36 autoshutdown mode (pm1 = 1, pm0 = 0) once the autoshutdown mode is selected, the ad7322 auto- matically enters shutdown on the 15 th sclk rising edge. in autoshutdown mode, all internal circuitry is powered down. the ad7322 retains information in the registers during autoshutdown. the track-and-hold is in hold mode during autoshutdown. on the rising cs edge, the track-and-hold, which was in hold during shutdown, returns to track as the ad7322 begins to power up. the power-up from autoshutdown is 500 s. when the control register is programmed to transition to autoshut- down mode, it does so on the 15 th sclk rising edge. figure 47 shows the part entering autoshutdown mode. once in autoshut- down mode, the cs signal must remain low to keep the part in autoshutdown mode. the ad7322 automatically begins to power up on the cs rising edge. the t power-up for autoshutdown is required before a valid conversion, initiated by bringing the cs signal low, can take place. when this valid conversion is complete, the ad7322 powers down again on the 15 th sclk rising edge. the cs signal must remain low again to keep the part in autoshutdown mode. autostandby mode (pm1 = 0, pm0 = 1) in autostandby mode, portions of the ad7322 are powered down, but the on-chip reference remains powered up. the reference bit in the control register should be 1 to ensure that the on-chip reference is enabled. this mode is similar to auto- shutdown, but allows the ad7322 to power up much faster. this allows faster throughput rates to be achieved. as is the case with the autoshutdown mode, the ad7322 enters standby on the 15 th sclk rising edge when the control register is updated (see figure 47 ). the part retains information in the registers during standby. once in autostandby mode, the cs signal must remain low to keep the part in autostandby mode. the ad7322 remains in standby until it receives a cs rising edge. the adc begins to power up on the cs rising edge. on the cs rising edge, the track-and-hold, which was in hold mode while the part was in standby, returns to track. the power-up time from standby is 750 ns. the user should ensure that 750 ns have elapsed before bringing cs low to attempt a valid conversion. once this valid conversion is complete, the ad7322 again returns to standby on the 15 th sclk rising edge. the cs signal must remain low to keep the part in standby mode. figure 47 shows the part entering autoshutdown mode. the sequence of events is the same when entering autostandby mode. in figure 47 , the power management bits are configured for auto- shutdown. for autostandby mode, the power management bits, pm1 and pm0, should be set to 0 and 1, respectively. cs 11 6 15 1 16 15 sclk sdata din valid data valid data data into control register data into control register t power-up control register is loaded on the first 15 clocks, pm1 = 1, pm0 = 0 part enters shutdown mode on the 15th rising sclk edge as pm1 = 1, pm0 = 0 p ar tbeginstopower u p on cs rising edge the p ar t is fully powered up once t power-up has elapsed 0 4863-042 figure 47. entering autoshutdown/autostandby mode
ad7322 rev. a | page 29 of 36 power vs. throughput rate the power consumption of the ad7322 varies with throughput rate. the static power consumed by the ad7322 is very low, and a significant power savings can be achieved as the throughput rate is reduced. figure 48 and figure 49 shows the power vs. throughput rate for the ad7322 at a v cc of 3 v and 5 v, respectively. both plots clearly show that the average power consumed by the ad7322 is greatly reduced as the sample frequency is reduced. this is true whether a fixed sclk value is used or if it is scaled with the sampling frequency. figure 48 and figure 49 show the power consumption when operating in normal mode for a fixed 20 mhz sclk and a variable sclk that scales with the sampling frequency. 12 0 0 1100 throughput rate (ksps) average power (mw) 10 8 6 4 2 100 200 300 400 500 600 700 800 900 1000 variable sclk 20mhz sclk v cc =3v v dd /v ss = 12v t a =25c internal reference 04863-052 figure 48. power vs. throughput rate with 3 v v cc 20 0 0 1000 throughput rate (khz) average power (mw) 18 16 14 12 10 8 6 4 2 100 200 300 400 500 600 700 800 900 20mhz sclk variable sclk v cc =5v v dd /v ss = 12v t a =25c internal reference 04863-053 figure 49. power vs. throughput rate with 5 v v cc
ad7322 rev. a | page 30 of 3 6 serial interface figure 50 shows the timing diagram for the serial interface of the ad7322. the serial clock applied to the sclk pin provides the conversion clock and controls the transfer of information to and from the ad7322 during a conversion. the cs signal initiates the data transfer and the conversion process. the falling edge of cs puts the track-and-hold into hold mode and takes the bus out of three-state. then the analog input signal is sampled. once the conversion is initiated, it requires 16 sclk cycles to complete. the track-and-hold goes back into track mode on the 14 th sclk rising edge. on the 16 th sclk falling edge, the dout line returns to three-state. if the rising edge of cs occurs before 16 sclk cycles have elapsed, the conversion is terminated, and the dout line returns to three-state. depending on where the cs signal is brought high, the addressed register may be updated. data is clocked into the ad7322 on the sclk falling edge. the three msbs on the din line are decoded to select which register is addressed. the control register is a 12-bit register. if the control register is addressed by the three msbs, the data on the din line is loaded into the control on the 15 th sclk rising edge. if the range register is addressed, the data on the din line is loaded into the addressed register on the 11 th sclk falling edge. conversion data is clocked out of the ad7322 on each sclk falling edge. data on the dout line consists of two leading zero bits, a channel identifier bit, a sign bit, and a 12-bit conversion result. the channel identifier bit is used to indicate which channel corresponds to the conversion result. the first leading zero bit is clocked out on the cs falling edge, and the second zero bit is clocked out on the first sclk falling edge. zero 12345 13141516 write zero reg sel lsb msb add0 sign db11 db10 db2 db1 db0 t 2 t 6 t 4 t 9 t 10 t 3 t 7 t 5 t 8 t 1 t quiet t convert sclk cs dout three- state three-state din zero identification bit 04863-036 don?t care figure 50. serial interface timing diagram (control register write)
ad7322 rev. a | page 31 of 3 6 microprocessor interfacing the serial interface on the ad7322 allows the part to be directly connected to a range of different microprocessors. this section explains how to interface the ad7322 with some common micro- controller and dsp serial interface protocols. ad7322 to adsp-21xx the adsp-21xx family of dsps interface directly to the ad7322 without requiring glue logic. the v drive pin of the ad7322 takes the same supply voltage as that of the adsp-21xx. this allows the adc to operate at a higher supply voltage than its serial interface. the sport0 on the adsp-21xx should be configured as shown in table 14 . table 14. sport0 control register setup setting description tfsw = rfsw = 1 alternative framing invrfs = invtfs = 1 active low frame signal dtype = 00 right justify data slen = 1111 16-bit data word isclk = 1 internal serial clock tfsr = rfsr = 1 frame every word irfs = 0 internal receive frame sync itfs = 1 internal transmit frame sync the connection diagram is shown in figure 51 . the adsp-21xx has tfs0 and rfs0 tied together. tfs0 is set as an output, and rfs0 is set as an input. the dsp operates in alternative framing mode, and the sport0 control register is set up as described in table 14 . the frame synchronization signal generated on the tfs is tied to cs and, as with all signal processing applications, requires equidistant sampling. however, as in this example, the timer interrupt is used to control the sampling rate of the adc and under certain conditions equidistant sampling cannot be achieved. ad7322 1 adsp-21xx 1 sclk sclk0 cs tfs0 rfs0 dout din dt0 dr0 v dd v drive 1 additional pins omitted for clarity. 0 4863-037 figure 51. interfacing the ad7322 to the adsp-21xx the timer registers are loaded with a value that provides an interrupt at the required sampling interval. when an interrupt is received, a value is transmitted with tfs/dt (adc control word). the tfs is used to control the rfs and, therefore, the reading of data. the frequency of the serial clock is set in the sclkdiv register. when the instruction to transmit with tfs is given (ax0 = tx0), the state of the serial clock is checked. the dsp waits until the sclk goes high, low, and then high again before starting the transmission. if the timer and sclk are chosen so that the instruction to transmit occurs on or near the rising edge of sclk, data can be transmitted either immediately or at the next clock edge. for example, the adsp-2111 has a master clock frequency of 16 mhz. if the sclkdiv register is loaded with the value 3, an sclk of 2 mhz is obtained, and eight master clock periods elapse for every one sclk period. if the timer registers are loaded with the value 803, 100.5 sclks occur between interrupts and, subsequently, between transmit instructions. this situation leads to nonequidistant sampling because the transmit instruction occurs on an sclk edge. if the number of sclks between interrupts is an integer of n, equidistant sampling is implemented by the dsp. ad7322 to adsp-bf53x the adsp-bf53x family of dsps interface directly to the ad7322 without requiring glue logic, as shown in figure 52 . the sport0 receive configuration 1 register should be set up as outlined in table 15 . ad7322 1 adsp-bf53x 1 v dd v drive sclk rsclk0 din dt0 dout dr0 cs rfs0 1 additional pins omitted for clarity. 04863-038 figure 52. interfacing the ad7322 to the adsp-bf53x table 15. sport0 receive configuration 1 register setting description rckfe = 1 sample data with falling edge of rsclk lrfs = 1 active low frame signal rfsr = 1 frame every word irfs = 1 internal rfs used rlsbit = 0 receive msb first rdtype = 00 zero fill irclk = 1 internal receive clock rspen = 1 receive enable slen = 1111 16-bit data-word tfsr = rfsr = 1 transmit and receive frame sync
ad7322 rev. a | page 32 of 3 6 application hints layout and grounding the printed circuit board that houses the ad7322 should be designed so that the analog and digital sections are confined to certain areas of the board. this design facilitates the use of ground planes that can easily be separated. to provide optimum shielding for ground planes, a minimum etch technique is generally best. all agnd pins on the ad7322 should be connected to the agnd plane. digital and analog ground pins should be joined in only one place. if the ad7322 is in a system where multiple devices require an agnd and dgnd connection, the connection should still be made at only one point. a star point should be established as close as possible to the ground pins on the ad7322. good connections should be made to the power and ground planes. this can be done with a single via or multiple vias for each supply and ground pin. avoid running digital lines under the ad7322 device because this couples noise onto the die. however, the analog ground plane should be allowed to run under the ad7322 to avoid noise coupling. the power supply lines to the ad7322 device should use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. to avoid radiating noise to other sections of the board, com- ponents with fast switching signals, such as clocks, should be shielded with digital ground and never run near the analog inputs. avoid crossover of digital and analog signals. to reduce the effects of feedthrough within the board, traces should be run at right angles to each other. a microstrip technique is the best method, but its use may not be possible with a double-sided board. in this technique, the component side of the board is dedicated to ground planes, and signals are placed on the other side. good decoupling is also important. all analog supplies should be decoupled with 10 f tantalum capacitors in parallel with 0.1 f capacitors to agnd. to achieve the best results from these decoupling components, they must be placed as close as possible to the device, ideally right up against the device. the 0.1 f capacitors should have a low effective series resistance (esr) and low effective series inductance (esi), such as is typical of common ceramic and surface-mount types of capacitors. these low esr, low esi capacitors provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. power supply configuration if the supply voltage for the analog input circuitry is different from that of the ad7322 v dd and v ss supplies or if the analog input can be applied to the ad7322 before v dd and v ss are established, then it is recommended that schottky diodes be placed in series with the ad7322 v dd and v ss supply signals. figure 53 shows this schottky diode configuration. bat43 schottky diodes are used. 04863-056 v in 0 v in 1 cs sclk dout din v dd v cc v ss ad7322 1 v? v +3v/5 v 1 additional pins omitted for clarity. figure 53. schottky diode connection in an application where nonsymmetrical v dd and v ss supplies are being used, adhere to the following guidelines. table 16 outlines the v ss supply range that can be used for particular v dd voltages when nonsymmetrical supplies are required. when operating the ad7322 with low v dd and v ss voltages, it is recommended that these supplies be symmetrical. for the 0 v to 4 v ref range, v ss can be tied to agnd as per minimum supply recommendations outlined in table 6 . table 16. nonsymmetrical v dd and v ss requirements v dd typical v ss range 5 v ?5 v to ?5.5 v 6 v ?5 v to ?8.5 v 7 v ?5 v to ?11.5 v 8 v ?5 v to ?15 v 9 v ?5 v to ?16.5 v 10 v to 16.5 v ?5 v to ?16.5 v
ad7322 rev. a | page 33 of 3 6 outline dimensions compliant to jedec standards mo-153-ab-1 061908-a 8 0 4.50 4.40 4.30 14 8 7 1 6.40 bsc pin 1 0.65 bsc 5.10 5.00 4.90 1.20 max 1.05 1.00 0.80 0.15 0.05 0.30 0.19 0.20 0.09 0.75 0.60 0.45 seating plane coplanarity 0.10 shrink small outline package [tssop] (ru-14) ns show in millimeters figure 54. 14-lead thin dimensio ordering guide model 1 temperature range package description package option AD7322BRUZ C40c to +85c 14-lead tssop ru-14 AD7322BRUZ-reel C40c to +85c 14-lead tssop ru-14 AD7322BRUZ-reel7 C40c to +85c 14-lead tssop ru-14 eval-ad7322cbz 2 evaluation board eval-control brd2z 3 controller board 1 z = rohs compliant part. 2 this can be used as a standalone evaluation board or in conjunction with the eval- 3 this board is a complete unit allowing a pc to control and communicate with evaluation kit, the particular adc evaluation board (for exampl e, eval-ad7322cbz), evaluation board data sheet for more information. con all analog s evaluation boards ending o order a complete the ev ol brd2z, and a 12 v tra ed. see the relevant trol board for evaluation/demonstration p urposes. device in the cb designators. t rder al-contr nsformer must be o
ad7322 rev. a | page 34 of 3 6 notes
ad7322 rev. a | page 35 of 3 6 notes
ad7322 rev. a | page 36 of 36 ?2005C2010 analog devices, inc. all rights reserved. trademarks and registered trademarks are the prop erty of their respective owners. d04863-0-1/10(a) notes

▲Up To Search▲

Price & Availability of AD7322BRUZ

	To Download AD7322BRUZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .