designed & dimensioned in millimeters[inches] this product manufactured with lead-free processing pb do not scale from this print "a" mm "b" mm "c" mm "d" mm "e" mm cable stripping dimensions per configurations (see table 1)(see note 12,13,14,15) fig. 2 c c c rfx6t-xxxxx-xxxxxx-xxxx overall cable length millimeters of cable 0100 min. (see note 8 & 9) end 1 connector end 2 connector or preparation -t4rp: bnc7t-p-c-xx-ra-ca6 (see sheet 2) -t4sp: bnc7t-p-c-xx-st-ca6 (see sheet 2) -sing: single ended (one end only, see note 11) -xxxxxx: stripped and tinned (one end only- see note 11-15, sheet 2, fig. 3) -t4rp: bnc7t-p-c-xx-ra-ca6 (see sheet 2) -t4sp: bnc7t-p-c-xx-st-ca6 (see sheet 2) end 1 plating option 3: alternate gold / nickel (see sheet 2 for plating specifics) (see fig. 2) "c" format: x.x mm (see fig. 2) "b" format: x.x mm (see fig. 2) "a" format: x.x mm 3: alternate gold / nickel *(leave blank for -sing or -xxxxxx end 2 preparation) end 2 plating option 0: cca-6 (rg-6 cable) b: cca-1694a (belden 1694a cable) cable callout c c c fig. 1 rfx6t-t4spx-t4rpx-xxxx shown c do not leave any space blank, each must contain a numeric character 0 thru 9. sheet of unless otherwise specified, dimensions are in millimeters [inches]. tolerances are: decimals angles .x: 0.3 [.01] 2 .xx: 0.13 [.005] .xxx: 0.051 [.0020] material: true 75 ohm, rf6t cable assembly by: rfx6t-xxxxx-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing r musser 03/27/2009 2 1 sheet scale: 2:1 see end 1 and end 2 assembly prints revision a f:\dwg\misc\mktg\rfx6t-xxxxx-xxxxxx-xxxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322 notes: 1. represents a critical dimension 2. cable cut length: = (length: xxxx) - (subtractor for end 1) - (subtractor for end 2) (see table 1 for subtractors) 3. assembly to be 100% tested for opens & shorts 4. assembly to be 100% hi-pot tested per table 1 5. after final electrical test, label each cable assembly with 1 label-et 6. criticals on connector prints to be checked in process. 7. finished assemblies to be packaged per packaging standard co-hd-wi-3033-m. 8. cable stocked in inches, 1 inch = 25.4 millimeters 9. cable lengths longer than 500 millimeters are not supported by s.i. test data 10. minimum bend radius for rg6 = 63.5 [2.75]. 11. for sing ended or stripped and tinned assemblies: make a double ended assembly at twice the cable length and test before cutting assembly in half. 12. dim "a", "b", and "c" have a minimum value of 0.0mm & a maximum value of 9.9mm. 13. production of strip and tin for center dielectic use: a 14. production of strip and tin for shield use: d=a+b 15. production of strip and tin for jacket use: e=a+b+c 16. for -ra to -ra, connectors should both be oriented up (see sheet 2, fig. 4)
-t4rp (right angle plug) (use drawing no. bnc7t-p-c-xx-ra-ca6 for assembly instructions) plating 3: 10" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: bnc7t-p-c-mn-ra-ca6) plating 3: 10" min. gold center contact 100" min. nickel outer contact 100" min. nickel remaining metal parts (end connector p/n: bnc7t-p-c-mn-st-ca6) note: all critical dimensions on bnc7t-p-c-xx-st-ca6 that apply must be verified. note: all critical dimensions on bnc7t-p-c-xx-ra-ca6 that apply must be verified. -t4sp (straight plug) (use drawing no. bnc7t-p-c-xx-st-ca6 for assembly instructions) fig. 3 rfx6t-t4spx-102148-xxxx shown fig. 4 rfx6t-t4rpx-74rpx-xxxx shown (see note 16) sheet of true 75 ohm, rf6t cable assembly by: rfx6t-xxxxx-xxxxxx-xxxx dwg. no. description: proprietary note this document contains information confidential and proprietary to samtec, inc. and shall not be reproduced or transferred to other documents or disclosed to others or used for any purpose other than that which it was obtained without the expressed written consent of samtec, inc. do not scale drawing r musser 03/27/2009 2 2 sheet scale: 1:1 revision a f:\dwg\misc\mktg\rfx6t-xxxxx-xxxxxx-xxxx-mkt.slddrw 520 park east blvd, new albany, in 47150 phone: 812-944-6733 fax: 812-948-5047 e-mail: info@samtec.com code: 55322
|
