? 1999 ixys all rights reserved d1 - 35 d1 v rsm v rrm type v v 200 200 dsek 60-02a 200 200 dsek 60-02ar symbol test conditions maximum ratings per leg i frms t vj = t vjm 50 a i favm t c = 115 c; rectangular, d = 0.5 34 a i frm t p < 10 s; rep. rating, pulse width limited by t vjm 375 a i fsm t vj = 45 c; t = 10 ms (50 hz), sine 325 a t = 8.3 ms (60 hz), sine 350 a t vj = 150 c; t = 10 ms (50 hz), sine 290 a t = 8.3 ms (60 hz), sine 310 a i 2 t t vj = 45 c t = 10 ms (50 hz), sine 530 a 2 s t = 8.3 ms (60 hz), sine 510 a 2 s t vj = 150 c; t = 10 ms (50 hz), sine 420 a 2 s t = 8.3 ms (60 hz), sine 400 a 2 s t vj -40...+150 c t vjm 150 c t stg -40...+150 c p tot t c = 25 c 125 w m d * mounting torque with screw m3 0.45-0.55/4-5 nm/lb.in. mounting torque with screw m3.5 0.45-0.55/4-5 nm/lb.in. v isol ** 50/60 hz, rms, t = 1 minute, leads-to-tab 2500 v~ weight 6g * verson a only; ** version ar only symbol test conditions characteristic values per leg typ. max. i r t vj = 25 cv r = v rrm 200 a t vj = 25 cv r = 0.8 ? v rrm 50 a t vj = 125 cv r = 0.8 ? v rrm 5ma v f i f = 30 a; t vj = 150 c 0.85 v t vj =25 c 1.10 v v t0 for power-loss calculations only 0.72 v r t t vj = t vjm 4.2 m ? r thjc 1 k/w r thch 0.5 k/w t rr i f = 1 a; -di/dt = 100 a/ s; v r = 30 v; t vj = 25 c3550ns i rm v r = 100 v; i f = 30 a; -di f /dt = 100 a/ s45a l 0.05 h; t vj = 25 c dsek 60 i favm = 2x 34 a v rrm = 200 v t rr = 35 ns i favm rating includes reverse blocking losses at t vjm , v r = 0.8 v rrm , duty cycle d = 0.5 data according to iec 60747 refer to a single diode unless otherwise stated. ixys reserves the right to change limits, test conditions and dimensions features international standard package jedec to-247 ad planar passivated chips very short recovery time extremely low switching losses low i rm -values soft recovery behavior epoxy meets ul 94v-0 flammability classification version ar isolated and ul registered e153432 applications rectifiers in switch mode power supplies (smps) uninterruptible power supplies (ups) ultrasonic cleaners and welders advantages high reliability circuit operation low voltage peaks for reduced protection circuits low noise switching low losses operating at lower temperature or space saving by reduced cooling 839 common cathode fast recovery epitaxial diode (fred) a = anode, c = cathode to-247 ad isoplus 247 tm version a version ar a a c (tab) c a a c tab a c a
? 1999 ixys all rights reserved d1 - 36 d1 200 600 1000 0 400 800 0 10 20 30 40 50 60 70 0.001 0.01 0.1 1 10 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0 40 80 120 160 0.4 0.6 0.8 1.0 1.2 1.4 1.6 k f t vj c -di f /dt t s k/w 0 200 400 600 800 0 1 2 3 4 5 6 0.0 0.3 0.6 0.9 1.2 1.5 1.8 v fr di f /dt v 200 600 1000 0 400 800 5 15 25 0 10 20 30 10 100 1000 0.0 0.2 0.4 0.6 0.8 0.0 0.4 0.8 1.2 0 20 40 60 80 100 120 i rm q r i f a v f -di f /dt -di f /dt a/ s a v c t rr ns t fr z thjc a/ s s dsek 60-02 a/ s a/ s dsek 60, 200v t vj = 100c v r = 100v t vj = 100c i f = 35a fig. 3 typ. peak reverse current i rm versus -di f /dt fig. 2 typ. reverse recovery charge q r versus -di f /dt fig. 1 forward current i f versus v f t vj =100c t vj = 25c t vj = 100c v r = 100v t vj = 100c v r = 100v q r i rm fig. 4 dynamic parameters q r , i rm versus t vj fig. 5 typ. recovery time t rr versus -di f /dt fig. 6 typ. peak forward voltage v fr and t fr versus di f /dt t fr v fr fig. 7 transient thermal impedance junction to case 831 t vj =150c i f = 15a i f = 35a i f = 70a i f = 15a i f = 35a i f = 70a i f = 15a i f = 35a i f = 70a dim. millimeter inches min. max. min. max. a 19.81 20.32 0.780 0.800 b 20.80 21.46 0.819 0.845 c 15.75 16.26 0.610 0.640 d 3.55 3.65 0.140 0.144 e 4.32 5.49 0.170 0.216 f 5.4 6.2 0.212 0.244 g 1.65 2.13 0.065 0.084 h - 4.5 - 0.177 j 1.0 1.4 0.040 0.055 k 10.8 11.0 0.426 0.433 l 4.7 5.3 0.185 0.209 m 0.4 0.8 0.016 0.031 n 2.2 2.54 0.087 0.102 dimensions
|
