60 operate data @ 25 c must operate voltage: 75% of nominal voltage or less. must release voltage: 10% of nominal voltage or more. operate time (including bounce): 15 ms, max. release time (including bounce): 15 ms, max. at or from nominal coil voltage t9a series low cost 30 amp pc board or panel mount relay file e22575 file lr15734 contact ratings @ 25 c with relay properly vented. remove vent nib after soldering and cleaning. arrangements: 1 form a (spst-no), and 1 form c (spdt). material: silver-cadmium oxide. mechanical life: 10 million operations, typical. minimum contact load: 1a @ 5vdc or 12vac. initial contact resistance: 75 milliohms, max., @ min. rated current (switched). initial dielectric strength between open contacts: 1,500v rms. between contacts and coil: 2,500v rms. 6 kv surge using 1.2 m s/50 m s impulse wave or .5 m s C 100khz ring wave initial insulation resistance between mutually insulated elements: 10 9 ohms, min., @ 500vdc, 25 c and 50% r.h. coil data @ 25 c voltage: 5 to 110vdc. nominal coil power: 1.0w, (approx.) and 900mw (approx.) versions. maximum coil power: 2.8 watt. maximum coil temperature (5) : class f: 140 c. duty cycle: continuous. nominal dc resistance nominal nominal dc resistance nominal voltage 10% (ohms) current (ma) voltage 10% (ohms) current (ma) 5 27 185 22 545 40 6 40 150 24 660 36 9 97 93 28 890 31 12 155 77 36 1,450 25 15 256 59 48 2,560 19 18 380 47 110 13,450 8 20 450 44 coil data - 900mw coil data - 1 watt nominal dc resistance nominal nominal dc resistance nominal voltage 10% (ohms) current (ma) voltage 10% (ohms) current (ma) 5 25 200 18 324 56 6 36 167 22 484 45 9 81 111 24 576 42 12 144 83 48 2,304 21 15 225 67 110 12,100 9 features ? up to 30 amp switching in spst and 20 amp in spdt arrangements. ? immersion cleanable (6) , plastic sealed case available. ? meets ul 873 and ul 508 spacing C 1/8" through air, 1/4" over surface. ? load connections made via 1/4" q. c. terminals and safety wells accept insulated female q. c. terminals (mounting codes 2 & 5). ? ul class f insulation system standard. ? well suited for various industrial, commercial and residential applications. typical electrical load & life - 900mw coil contact contact load type of load operations arrangement 1 120vac 50 lra/16 fla 100,000 120vac 30 lra/11 fla 200,000 typical electrical load & life - 1 watt coil contact contact load type of load operations arrangement 1 30a @ 240vac ul general purpose 100,000 25a @ 240vac resistive heater 100,000 5 20a/10a @ 240vac ul general purpose 100,000 20a/10a @ 240vac ul resistive 100,000 20a/10a @ 28vdc resistive 100,000 ul 508/873 & csa contact ratings - 1 watt coil voltage load type n.o. contact n.c. contact 277vac tungsten * 5.4a C 277vac ballast 10a 3a 240vac motor 2 hp 1/2 hp 240vac resistive * 30a 20a 240vac general purpose? 30a 15a 240vac lra/fla **?? 80a/30a 30a/12a 240vac pilot duty * 470va 275va 125vac motor 1 hp 1/4 hp 120vac lra/fla 98a/22a C 120vac tungsten * 8.3a C 120vac pilot duty 470va C 28vdc resistive 20a 10a * rated 6,000 operations. ** higher ul & csa ratings available. ? for form c application, derate current to 20a (n.o.), 10a (n.c.). ?? for form c application, derate current to 67%. note: consult factory for other 900mw version contact ratings. .com .com .com 4 .com u datasheet
61 mechanical data termination: printed circuit and quick connect terminals (4) . enclosures (all have 94v-0 flammability rating): t9ap: unsealed, plastic dust cover. t9as: immersion cleanable, sealed plastic case (2 & 3) . t9av: vented, flux-tight, plastic cover. weight: q.c. version: 1.2 oz. (33g) approx. (mounting code 2 & 5). sealed model t9as: 0.9 oz. (26g) approx. (mounting code 1). notes (1) operating ambient temperature must consider must operate voltage change over temperature, contact temperature rise, coil temperature rise (if coil is not allowed to cool) and maximum coil temperature. specification ambient considers 20a load with coil cooled to ambient. (2) sealed relay terminals should not be bent. (3) remove knock-off nib after cleaning process for optimum life of sealed relays. (4) maximum soldering temperature is 500 f for 4 seconds. (5) class f coils are ul systems approved for maximum coil temperature of 140 c, by change of resistance method. (6) see application note 13c265 for proper relay mounting, termination, cleaning and pc board conductor width. coil rise test performed with 30a pc board to maintain 20 c maximum rise @ 30a. t9ap1d52-12 t9ap1d52-24 t9ap1d52-48 t9ap5d52-12 t9ap5d52-24 t9ap5d52-48 t9as1d12-110 t9as1d12-12 t9as1d12-18 t9as1d12-24 t9as1d12-48 t9as1d12-5 t9as1d22-110 t9as1d22-12 t9as1d22-24 t9as1d22-48 t9as1d22-5 t9as1l12-12 t9as1l12-24 t9as5d12-110 t9as5d12-12 t9as5d12-18 t9as5d12-24 t9as5d12-48 t9as5d12-5 t9as5d22-110 t9as5d22-12 t9as5d22-24 t9as5d22-48 t9as5d22-5 t9as5l12-12 t9as5l12-24 stock items C the following items are normally maintained in stock for immediate delivery. 0 20 40 60 80 100 120 140 180 160 140 120 100 80 60 0a 10a 20a 30a sealed relay, vented (note 3) pc terminals for coil & contacts applied continuous coil voltage (% of rated voltage) max. alowable ambient temp. (?) 40 60 80 100 120 140 180 160 140 120 100 80 60 relay with dust cover, flange mount 0a 10a 20a 30a applied continuous coil voltage (% of rated voltage) max. alowable ambient temp. (?) 0 20 40 60 80 100 120 140 180 160 140 120 100 80 60 sealed relay, vented (note 3) ; load connections via q.c. terminals, pc mount 0a 10a 20a 30a applied continuous coil voltage (% of rated voltage) max. alowable ambient temp. (?) environmental data storage temperature range: -55 c to 130 c. operating temperature range (1) : -55 c to +85 c. vibration, operational: 0.065" (1.65mm) max. excursions from 10-55 hz. with no contact opening >100 m s. shock, operational: 10g for 11 ms with no contact opening >100 m s. shock, mechanical: 100g. ambient temperature vs. coil voltage - 1 watt coil data below are average values and should be verified in application. tests were conducted within a 2' (.6 m) cube (still air); at nominal coil power @ 25 c; with normally open contact loaded; and with 4' (1.22 m) long, #10 awg load wires. p.c. board relays were mounted to a 30a, single side p.c. board (6) . ordering information typical part number b t9a s 5 d 2 2 -12 1. basic series: t9a = low cost, printed circuit board/panel power relay. 2. enclosure: p = unsealed, plastic dust cover (mounting code 5). s = immersion cleanable, knock off nib, sealed plastic case (mounting codes 1 & 2). v = vented, flux-tight (mounting code 1). 3. contact arrangement: 1 = 1 form a (spst-no). 5 = 1 form c (spdt). 4. coil input: d = dc voltage (1 watt) l = dc voltage (900mw) 5. mounting & termination: 1 = printed circuit board mounting; pc terminals for coil & contacts (a) . 2 = printed circuit board mounting; pc terminals for coil & contacts, and .250" (6.35mm) quick connects for contacts (b) . 5 = flanged mounting; .187" (4.75mm) quick connects for coil and .250" (6.35mm) quick connects for contacts (c) . 6. contact material: 2 = silver-cadmium oxide. 7. coil voltage: 5 = 5vdc 9 = 9vdc 15 = 15vdc 20 = 20vdc 24 = 24vdc 48 = 48vdc 6 = 6vdc 12 = 12vdc 18 = 18vdc 22 = 22vdc 36 = 36vdc 110 = 110vdc a) only available with enclosure code s & v. b) only available with enclosure code s. c) only available with enclosure code p. .com .com .com .com 4 .com u datasheet
62 t9as/v C mounting & termination code 1 .300 (7.62) .100 (2.54) .150 (3.81) .500 (12.7) .550 (13.97) .700 (17.78) .043 .003 dia. (1.09 .08) .081 .005 dia. (2.06 .13) .600 (15.24) .212 max. (5.38) pc board layouts (bottom views) t9ap/s C mounting & termination code 2 .140 max. (3.56) .250 max. (6.35) .300 (7.62) .100 (2.54) .150 (3.81) .500 (12.7) .550 (13.97) .700 (17.78) .043 .003 dia. (1.09 .08) .081 .005 dia. (2.06 .13) .600 (15.24) t9as/v C mounting & termination code 1 outline dimensions t9ap C mounting & termination code 5 din mount adapter - 9t91a001 wiring diagrams (bottom views) 1.67 (42.41) .50 (12.7) .50 (12.7) .20 (5.08) .40 (10.16) .79 (20.06) 3 holes for #6-32 screw 0.011 deep (.27) note: fits 35mm din track includes: 2 din clips 2 screws must be ordered in multiples of 50 1 form a t9as C mounting & termination code 2 1 form c .187 x .020 (4.75 x .508) quick connect 1.080 max. (27.43) 1.980 max. (50.29) 1.713 .010 (43.51 .25) .071 (1.80) rad. for #6 screw 1.280 max. (32.51) 1.100 max. (27.94) .250 x .032 (6.35 x .81) quick connect nc no com note: recommended mounting screw torque is 4.0-5.0 lbs.in when #6 screw is used. .032 x .062 (.81 x 1.57) .045 x .045 (1.14 x 1.14) .03 (.80) 2 places .250 x .032 quick (6.35 x .81) connect nc no com 1.280 max. (32.51) 1.080 max. (27.43) .130 .020 (3.30 .51) 1.100 max. (27.94) .032 x .062 (.8 x 1.6) terminals .212 max. (5.38) .10 max. (2.54) .045 x .045 (1.14 x 1.14) terminal .805 max. (20.4) .69 (17.6) 1.280 max. (32.51) 1.08 max. (27.43) .50 (12.8) .03 (.80) terminals .130 + .016 ?.010 3.30 + .41 ?25 ( ) .016 (.43) .com .com .com 4 .com u datasheet
|
