1 www.protekdevices.com 05152.r4 11/02 ulc0402fc3.3c thru ULC0402FC24C bidirectional low capacitance unbumped flip chip applica tions ? cellular phones ? handheld electronics ? personal digital assistants (pdas) ? notebook computers ? smart cards iec compa tibility (en61000-4) ? 61000-4-2 (esd): air - 15kv, contact - 8kv ? 61000-4-4 (eft): 40a - 5/50ns fea tures ? esd protection > 25 kilovolts ? available in six voltage types ranging from 3.3v to 24v ? 200 watts peak pulse power dissipation per line (8/20s) ? low clamping voltage ? monolithic structure ? low capacitance ? low standby current mechanical characteristics ? standard eia chip size: 0402 ? weight 0.73 milligrams (approximate) ? flammability rating ul 94v-0 ? 8mm plastic & paper tape and reel per eia standard 481 ? device marking on reel u0402 circuit diagram 05152 . . . engineered solutions for the transient environment?
2 www.protekdevices.com 05152.r4 11/02 ulc0402fc3.3c thru ULC0402FC24C device characteristics maximum ratings @ 25c unless otherwise specified operating temperature symbol value -55 c to 150 cc c -55 c to 150 c units t j t stg parameter storage temperature peak pulse power (t p = 8/20s) - see figure 1 p pp 200 watts 0.01 1 10 100 1,000 10,000 t d - pulse duration - s 0 5 10 15 20 25 30 t - time - s 0 20 40 60 80 100 120 i pp - peak pulse current - % of i pp test waveform parameters t f = 8s t d = 20s t f peak value i pp e -t t d = t i pp /2 figure 2 pulse wave form 10 100 1,000 10,000 p pp - peak pulse current - watts figure 1 peak pulse power vs pulse time 200w, 8/20s waveform electrical characteristics per line @ 25c unless otherwise specified pa r t number (see note 1) minimum breakdown voltage @ 1ma v (br) volts maximum clamping voltage (see fig. 2) @ i p = 1a v c volts maximum clamping voltage (see fig. 2) @8/20s v c @ i pp typical capacitance 0v @ 1 mhz c pf ulc0402fc3.3c ulc0402fc05c ulc0402fc08c ulc0402fc12c ulc0402fc15c ULC0402FC24C 3.3 5.9 8.0 12.0 15.0 24.0 4.0 6.0 8.0 13.3 16.7 26.7 7.0 11.0 13.2 19.8 25.4 37.2 12.5v @ 16a 13v @ 15a 18v @ 11a 26.9v @ 7.4a 34.5v @ 5.8a 50.6v @ 4a 70 35 32 30 25 20 maximum leakage current @v wm i d a 75 10 1 1 1 1 rated stand-off voltage v wm volts note 1: all devices are bidirectional. electrical characteristics apply in both directions. electrical characteristics for 3v, 8v, 12v, 15v and 24v are preliminary.
3 www.protekdevices.com 05152.r4 11/02 ulc0402fc3.3c thru ULC0402FC24C graphs esd test pulse - 12 kilovolt, 1/30ns (waveform) figure 5 overshoot & clamping voltage for ulc0402fc05c 5 volts per division 0 10 20 30 40 ulc0402fc05c 0 5 10 15 20 v c - clamping voltage - volts 0 4 8 12 14 figure 6 typical clamping voltage vs peak pulse current 10 6 2 i pp - peak pulse current - amps figure 4 reflow solder profile 225c 5-10 sec instantaneous to 200c soldering time cool down time 1-2 minutes to 150c 1-2 minutes to 25c pre-heat time 100c 200c note: this reflow profile does not take into account the printed circuit board (pcb) material heating time. additional time may be required for the preheat time and cool down time upon the pcb or board material. 0 25 50 75 100 125 150 t l - lead temperature - c 20 40 60 80 100 % of rated power peak pulse power 8/20s average power figure 3 power derating curve 0
4 www.protekdevices.com 05152.r4 11/02 ulc0402fc3.3c thru ULC0402FC24C copyright ? protek devices 2003 specifications: protek reserves the right to change the electrical and or mechanical characteristics described herein without notice (except jedec). design changes: protek reserves the right to discontinue product lines without notice, and that the fi nal judgement concerning selection and specifications is the buyer?s and that in furnishing engineering and technical assistance, protek assumes no responsibility with respect to the selection or specifications of such products. package outline & dimensions protek devices 2929 south fair lane, tempe, az 85282 tel: 602-431-8101 fax: 602-431-2288 e-mail: sales@protekdevices.com web site: www.protekdevices.com t ape & reel ordering informa tion: surface mount product is taped and reeled in accordance with eia-481. plastic tape: 7 inch reels - 5,000 pieces per reel. ordering suffix: -t75-1 (i.e., ulc0402fc05c-t75-1). paper tape: 7 inch reels - 10,000 pieces per reel. ordering suffix: -t710-2 (i.e., ulc0402fc05c-t710-2). a b c d e f i 0.46 nom 0.86 nom 0.99 0.0254 0.10 nom 0.35 nom 0.483 0.0254 0.406 nom 0.018 nom 0.034 nom 0.039 0.001 0.004 nom 0.014 nom 0.019 0.001 0.016 nom dim millimeters inches package dimensions notes: 1. controlling dimensions in inches. 2. decimal tolerances for mounting pad and outline: .xxx 0.05mm ( 0.002 ? ). 3. maximum chip size: 1.02 (0.040 ? ) by 0.51(0.020 ? ). package outline u0402 mounting pad tape & reel orienta tion note: 1. top view of tape. metal contacts are face down in tape package. single die 0402 d e f i side a b c top end 06020 rev 3 - 11/02 metalized die contacts 0.009 0.019 0.027 0.018 0.039 0.008 0.008 0.026 0.005 a b c d e f g h i 0.23 0.48 0.69 0.46 0.99 0.20 0.20 0.66 0.13 dim millimeters inches pad dimensions note: preferred: using 0.1mm (0.004 ? ) stencil. b c die contacts a h d i solder print diameter 0.010? - 0.012? f g die e solder pad
|
