rf monolithics, inc. phone: (972) 233-2903 fax: (972) 387-9148 e-mail: info@rfm.com page 1 of 2 rfm europe phone: 44 1963 251383 fax: 44 1963 251510 http://www.rfm.com ?1999 by rf monolithics, inc. the stylized rfm logo are registered trademarks of rf monolithics, inc. HO1077-022400 electrical characteristics characteristic sy notes mini- typical maxi- units operating frequency absolute frequency f o 1, 7 582.600 583 583.400 mhz tolerance from 583 mhz d f o 400 khz rf output power p o 3, 6 +10 +13 +15 dbm spurious outputs second harmonics 3, 6, 7 -15 dbc third and higher harmonics -20 nonharmonic <-80 -60 rf impedance nominal impedance z o 3 50 w operating load vswr g l 3, 5 1.5:1 dc power supply operating voltage v cc 3, 6 9.50 10.0 10.50 vdc operating current i cc 35 40 ma operating ambient temperature t a 3, 6 -30 +70 c lid symbolization (yy=year, ww=week) rfmHO1077 yyww dip 14-8 case ? saw frequency stabilization ? fundamental-mode oscillation at 583.00 mhz ? 0.8? x 0.5? x 0.25? metal dip case this general-purpose oscillator is stabilized by surface-acoustic-wave (saw) technology. fundamental oscil- lation at 583.0 mhz eliminates all internally generated spurious outputs except integral harmonics of 583.0 mhz. the compact size of the rugged, metal, hermetically-sealed case makes this oscillator suitable for a va- riety of applications. absolute maximum ratings rating value units dc supply voltage 0 to +13 vdc ambient temperature powered -40 to +70 c storage -40 to +85 583.00 mhz saw oscillator HO1077 caution: electrostatic sensitive device. observe precautions for handling. cocom caution: approval by the u.s. department of commerce is required prior to export of this device. notes: 1. one or more of the following united states patents apply: 4,616,197; 4,610,681; and 4,761,616. 2. unless noted otherwise, all specifications are listed at t a = +25c 2c, v cc = nom- inal voltage 0.01 vdc, and load impedance = 50 w with vswr 1.5:1. 3. the design, manufacturing process, and specifications of this device are subject to change without notice. 4. applies to oscillator only and not to sidebands caused by external electrical or mechanical sources. (dedicated external voltage regulation with low-frequency filter- ing for the dc power supply and proper circuit board layout are recommended for optimum spectral purity.) 5. for specified maximum operating load vswr (any angle) at f o . (no instability or damage will occur for any passive load impedance.) 6. for any combination of v cc and t a within the specified operating ranges. 7. applies for any combination of note 5 and 6 conditions. block diagram electrical connections rf output v cc buffer amplifier saw oscillator top view 1 v v cc cc case ground 2 case ground 6 rf output 7 13 case ground 9 case ground 8 cc
583.00 mhz saw oscillator rf monolithics, inc. phone: (972) 233-2903 fax: (972) 387-9148 e-mail: info@rfm.com page 2 of 2 rfm europe phone: 44 1963 251383 fax: 44 1963 251510 http://www.rfm.com ?1999 by rf monolithics, inc. the stylized rfm logo are registered trademarks of rf monolithics, inc. HO1077-022400 dip14-8 metal dual-inline package with 8 leads in a 14-lead dip configuration dimension mm inches min max min max a ? 20.45 ? 0.805 b ? 12.83 ? 0.505 c ? 6.35 ? 0.250 d 0.40 0.51 0.016 0.020 e 0.64 nominal 0.025 nominal f 7.62 nominal 0.300 nominal g 2.54 nominal 0.100 nominal h 15.24 nominal 0.600 nominal k 5.97 6.73 0.235 0.265 l 1.30 ? 0.051 ? m ? 11.18 ? 0.440 n ? 18.80 ? 0.740 r 1.75 2.26 0.069 0.089 top view bottom view d (8 places) b m a n e pin 1 mark (optional) (4 places) l c k f r (3 places) h g (4 places) 1 2 6 7 8 9 13 14
|
