View YOD1C_2356300.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

oled push switches 96rgbx96 (1.10) oled switches YOD1C sales@greatecs.com www.greatecs.com 1 distinctive characteristics - organic led technology - wide view angle of 160 - exceptional contrast and brightness: 50times greater brightness than previous lcd products, four times more enhanced resolution - high resolution provides sharp, clear images of very small characters - single power / built in dc to dc converter for oel panel - distinct, long travel of 5mm - sophisticated housing for assembly easily - support parallel and serial interface gerneral specifications dispaly specifications - display type: oled - display mode: passive matrix - display color: 65,536 colors (maximum) - drive duty: 1/96 duty - number of pixels: 96(rgb)x96 - pixel size: 0.049x0.191 mm - pixel pitch: 0.069x0.207 mm mechanical specifications - dimension: 32.0x32.0x22.3 mm (lxwxh) - window size: 21.65x21.65 mm (lxw) - active area: 19.852x 19.856 mm - assembly: pitch 1.27mm / 12 pin connector*2 - assembly on pcb easy & removable & flexible electrical characteristic - supply voltage: 2.4 ~ 3.3 v - single voltage control display module - built-in dc to dc power supply to drive oled - driver ic: seps114a - interface: parallel/serial/68xx/80xx/4-wire spi typical switch dimensions example picture
oled push switches 96rgbx96 (1.10) oled switches YOD1C sales@greatecs.com www.greatecs.com 2 pin assignments n o i t c n u f e p y t l o b m y s . o n n i p 1 vdd p power supply for core vdd this is a voltage supply pin. it must be connected to external source. 2 vss p ground for system this is a ground pin. it must be connected to external source. 3sw i terminal of switch. normally open. 4sw i terminal of switch. normally open. 5 c80 i select the cpu type low: 80xx-series mcu high: 68xx-series mcu 6 ps i select parallel/serial interface type low: serial interface high: parallel interface 7 cs# i chip select this is the chip select input. the chip is enable for mcu communication only when cs# is pulled low. 8 res# i power reset for controller and drive this is reset signal input. when the pin is low, initialization of the chip is executed. 9 d/c# i data/ command control this pin is data/command control pin. when the pin is pulled high, the input at d0~d7 is treated as display data. when the pin is pulled low, the input at d0~d7 will be transferred to the command register. 10 wr# (r/w#) i write or read/write select when 80xx interface mode is selected, the pin will be the write (wr#) input. when interfacing to a 68xx-series microprocessor, the pin will be used as read/write (r/w#) selection input. pull this pin to high for read mode and pull it to low for write mode. 11 rd#(e) i read or read/write enable when 80xx interface mode is selected, the pin will be the read (rd#) input. when interfacing to a 68xx-series microprocessor, the pin will be used as the enable (e) signal. read/write operation is initiated when this pin is pulled high and the cs# is pulled low. 12 nc - reserved pin 13~20 d0~d7 i/o host data input /output bus these pins are 8-bit bi-direction al data bus to be connected to the microprocessors data bus. n o i t p i r c s e d s p 0 d[0] scl: synchronous clock input d[1] sdi: serial data input d[2]: sdo: serial data output d[3] r/w: serial read (high) / write (low) 1 8-bit bus: d[7:0] when using spi, the unused pins must be connected to vss. 21 vss p ground for system this is a ground pin. it must be connected to external source. 22 vcc-ctl i oled driver power supply on/ off control when this pin is pulled high, the panel power supply will be turned on. when this pin is pulled low, the panel power supply will be turned off.
oled push switches 96rgbx96 (1.10) oled switches YOD1C sales@greatecs.com www.greatecs.com 3 absolute maximum ratings 23 nc - reserved pin 24 vcc p oled driver power supply output this pin is oled driver power supply output. when vcc-ctl is pulled high, the pin will be output about 13v voltage. parameter symbol min max unit notes supply voltage for operation v dd -0.3 4 v 1,2 supply voltage for display vcc_c -0.3 16 v 1,2 operating temperature t op -30 70 w - storage temperature t stg -40 80 w - note1 p all the above voltages are on the basis of vss=0v note2 p when this module is used beyond the above absolute maximum ratings, permanent breakage of the module may occur. also for normal operations, it is desirable to use this module under the conditions according to section 6 electrical characteristics. if this module is used beyond these conditions, malfunctioning of the module can occur and the reliability of the module may deteriorate.
oled push switches 96rgbx96 (1.10) oled switches YOD1C sales@greatecs.com www.greatecs.com 4 electrical characteristics 1. dc characteristics characteristics symbol conditions min typ max unit supply voltage for operation v dd 2.4 2.8 3.3 v supply voltage for display v cc_c note 3 12.5 13 13.5 v high level input v ih 0.8v dd -v dd v low level input v il 0 - 0.4 v high level output v oh i oh = -0.1ma v dd -0.4 - v low level output v ol i ol = -0.1ma - 0.4 v operating current for v dd i dd - 2.5 3.5 ma operating current for v cc_c i cc note 4 note 5 - 9.5 17.1 11.9 21.4 ma ma note 3: brightness (l br ) and supply voltage for display (vcc_c) are subject to the change of the panel characteristics and the customers request. note 4: v dd = 2.8v, v cc_c = 13v, 50% display area turn on. note 5: v dd = 2.8v, v cc_c = 13v, 100% display area turn on. 2. optics characteristics characteristics symbol conditions min typ max unit brightness l br with polarizer 80 100 - cd/m 2 c.i.e. (white) (x) (y) with polarizer 0.26 0.29 0.30 0.33 0.34 0.37 c.i.e. (red) (x) (y) with polarizer 0.60 0.30 0.64 0.34 0.68 0.38 c.i.e. (green) (x) (y) with polarizer 0.27 0.58 0.31 0.62 0.35 0.66 c.i.e. (blue) (x) (y) with polarizer 0.10 0.12 0.14 0.16 0.18 0.20 dark room contrast cr - >2000:1 - view angle >160 - - degree * optical measurement taken at v dd = 2.8v, v cc_c = 13v.
oled push switches 96rgbx96 (1.10) oled switches YOD1C sales@greatecs.com www.greatecs.com 5 timing chart 1. 68xx-series mpu parallel interface timing characteristics symbol description min max unit port t ah6 address setup timing (read) (write) 10 5 - - ns ns csb rs t as6 address hold timing (read) (write) 10 5 - - ns ns t cyc6 0 0 2 g n i m i t e l c y c m e t s y s - ns e t elr6 0 9 h t d i w e s l u p l d a e r - ns t ehr6 0 9 h t d i w e s l u p h d a e r - ns t cyc6 0 0 1 g n i m i t e l c y c m e t s y s - ns t elw6 write l pulse width 45 - ns t ehw6 write h pulse width 45 - ns t rdd6 read data output delay time *cl**15 p f data hold timing 0 70 ns d[17:9] t rdh6 0 70 ns t ds6 data setup timing 40 - ns t dh6 0 1 g n i m i t d l o h a t a d -ns (v dd = 2.8v, t a = 25 c ) * all the timing reference is 10% and 90% of v dd (read timing) (write timing)
oled push switches 96rgbx96 (1.10) oled switches YOD1C sales@greatecs.com www.greatecs.com 6 timing chart 2. 80xx-series mpu parallel interface timing characteristics symbol description min max unit port t as8 address setup timing 5 - ns csb a0 t ah8 address hold timing 5 - ns t cyc8 system cycle timing 200 - ns rdb t rdlr8 read l pulse width 90 - ns t rdhr8 read h pulse width 90 - ns t cyc8 system cycle timing 100 - ns wrb t wrlw8 write l pulse width 45 - ns t wrhw8 write h pulse width 45 - ns t rdd8 read data output delay time *cl = 15 p f data hold timing -60ns d[7:0] t rdh8 060ns t ds8 s n - 0 3 g n i m i t p u t e s a t a d t dh8 s n - 0 1 g n i m i t d l o h a t a d (v dd = 2.8v, t a = 25 c) * all the timing reference is 10% and 90% of v dd . (read timing) (write timing)
oled push switches 96rgbx96 (1.10) oled switches YOD1C sales@greatecs.com www.greatecs.com 7 timing chart 3. series interface timing characteristics symbol description min max unit port t cycs serial clock cycle 200 - ns scl t shw scl l pulse width 90 - ns t slw scl h pulse width 90 - ns t d ss data setup timing 25 - ns sdi t dhs data hold timing 25 - ns t css csb-scl timing 25 - ns csb t csh csb-hold timing 25 - ns t rss rs-scl timing 25 - ns rs t rsh rs-hold timing 25 ns (v dd = 2.8v, t a =25 c) * all the timing reference is 10% and 90% of v dd .
oled push switches 96rgbx96 (1.10) oled switches YOD1C sales@greatecs.com www.greatecs.com 8 function specification 1. commands refer to the technical manual for the seps114a 2. power down and power up sequence to protect oel panel and extend the panel life time, the driver ic power up/down routine should include a delay period between high voltage and low voltage power sources during turn on/off. it gives the oel panel enough time to complete the action of charge and discharge before/after the operation. 2.1. power up sequence 1. power up v dd & v ddio 2. send display off command 3. initialization 4. clear screen 5. power up v cc_c 6. delay 100ms (when v cc_c is stable) 7. send display on command 2.2. power down sequence 1. send display off command 2. power down vcc_c 3. delay 100ms (when vcc_c is reach 0 and panel is completely discharges) 4. power down v
oled push switches 96rgbx96 (1.10) oled switches YOD1C sales@greatecs.com www.greatecs.com 9 function specification 3. reset circuit when rstb input is low, the chip is initialized with the following status: 1. standby mode: on 2. frame frequency: 95hz 3. oscillation: internal oscillator off 4. ddram write horizontal address: xs = 0x00, xe = 0x5f 5. ddram write vertical address: ys = 0x00, ye = 0x5f 6. display data ram write: mdir1 = 0, mdir0 = 0, vh = 0 7. row scan shift direction: r0, r1, , r94, r95 8. column data shift direction: c0, c1, , c286, c287 9. display on/off: off 10. panel display size: fx = 0x00, tx = 0x5f, fy = 0x00, ty = 0x5f 11. display data ram read column/row address: dx = 0x00, dy = 0x00 12. discharge time: 8 clock 13. peak pulse delay: 5 clock 14. peak pulse width time (r/g/b): 5 clock 15. precharge current (r/g/b): 0 ? a 16. driving current (r/g/b): 0 ? a
oled push switches 96rgbx96 (1.10) oled switches YOD1C sales@greatecs.com www.greatecs.com 10 command application example command usage and explanation of an actual example oled_vcc_ctl=0; //off power up panel vcc oled_reset=0; //reset driver ic for 100ms delay_100ms (1); oled_reset=1; set soft_reset (0x01, 0x00); set standby_on_off (0x14, 0x00); set disp_on_off (0x02, 0x00); set analog control (0x0f, 0x40); set osc_adjust (0x1a, 0x03); set displaystart_x (0x38, 0x00); set displaystart_y (0x39, 0x00); setrgb_if(0xe0,0x00); set rgb_pol (0xe1, 0x00); set display_mode_co ntrol (0xe5, 0x00); set cpu_if (0x0d, 0x00); set memory_write/read (0x1d, 0x01); set row_scan_direction (0x09, 0x00); set r ow_scan_mode (0x13, 0x00); set column_current_r (0x40, 0x7f); set column_current_g (0x41, 0x65); set column_current_b (0x42, 0x7b); set row_overlap (0x48, 0x03); set discharge_time (0x18, 0x03); set peak_pulse_delay (0x16, 0x00); set peak_pulse_width_r (0x3a, 0x03); set peak_pulse_width_g (0x3b, 0x03); set peak_pulse_width_b (0x3c, 0x02); set precharge_current_r (0x3d, 0x09); set precharge_curre nt_g (0x3e, 0x09); set scan_off_level (0x49, 0x0f); set display_x1 (0x30, 0x00); setdisplay_x2(0x31,0x5f); set disply_y1 (0x32, 0x00); set display_y2 (0x 33, 0x5f); clear screen; set disp_on_off (0x02, 0x01); oled_vcc=1; //power up vcc delay_100ms(1); //dealy 100ms set_display_on(0xaf); // display on (0x00/0x01) if the noise is accidentally occurred at the displaying window during the operation, please reset the display in order to recover the display function.
oled push switches 96rgbx96 (1.10) oled switches YOD1C sales@greatecs.com www.greatecs.com 11 reliability 1. contents of reliability test item conditions criteria high temperature operation 70 c, 240hrs the operational functions work. low temperature operation -30 c, 240hrs high temperature storage 80 c, 240hrs low temperature storage -40 c, 240hrs high temperature/ humidity operation 60 c, 90% rh, 120hrs thermal shock -40 c !=>?! 85 c, 24 cycles 60 mins dwell *the samples used for the above test do not include polarizer. *no moisture condensation is observed during tests. 2. lifetime end of lifetime is specified as 50% of initial brightness. parameter min max unit condition notes operating life time 10,000 - hr 100 cd/ n 3 , 50% checkerboard * storage life time 20,000 - hr ta = 25 c, 50% rh *the average operating lifetime at room temperature is estimated by the accelerated operation at high temperature conditions. 10.3. failure check standard after the completion of the described reliability test, the samples were left at room temperature for 2 hrs prior to conducting the failure test at 23 5 c p 55 15% rh.

▲Up To Search▲

Price & Availability of YOD1C

	To Download YOD1C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .