1 performance power pfc375 the pfc375 products of the performance power series incorporate high performance midrange power, active power factor correction (pfc), and high reliability to meet varied commercial and industrial requirements. providing tightly regulated dc power in a wide variety of single and multiple output configurations, the pfc375 is designed to provide full output power with only 300 linear feet per minute (lfm) forced air cooling (factory installed fan optional). other features include remote sense, power fail, logic level inhibit, dc power good. main channel current sharing is provided for redundant applications. the pfc375 is available with sae mountings or optional metric mountings. the pfc375 product line is approved to the latest international regulatory standards, and displays the ce mark. features power factor correction (pfc) meets en61000-3-2 fully regulated outputs main output remote sense current share, power fail, and power good signals overtemperature, overvoltage, and overcurrent protected available with metric and sae mountings input transient & esd compliance to en61000-4-2/-3/-4/-5 fan output voltage and optional fan multiple output model selection chart - isolated v3 and v4 can be used as positive or negative outputs model output adjustment output peak output line load ripple & noise initial setting voltage range current (note 1) current (note 2) regulation regulation %p-p (note 3) accuracy +5v 4.5v to 5.5v 3.5 - 40a 40a 0.4% 0.8% 1% 4.98v to 5.02v pfc375-3000 +12v 11.3v to 12.6v 10a 16a 0.9% 0.9% 1% 11.9v to 12.1v 12v 11.3v to 12.6v 6a 10a 0.9% 0.9% 1% 11.9v to 12.1v +5v 4.5v to 5.5v 3.5 - 40a 40a 0.4% 0.8% 1% 4.98v to 5.02v pfc375-3001 +15v 14.2v to 15.8v 10a 16a 0.7% 0.7% 1% 14.9v to 15.1v 15v 14.2v to 15.8v 6a 10a 0.7% 0.7% 1% 14.9v to 15.1v +5v 4.5v to 5.5v 3.5 - 40a 40a 0.4% 0.8% 1% 4.98v to 5.02v pfc375-3002 +12v 11.3v to 12.6v 10a 16a 0.9% 0.9% 1% 11.9v to 12.1v 5v 4.5v to 5.5v 6a 6a 0.4% 1% 1% 4.98v to 5.02v +5v 4.5v to 5.5v 3.5 - 40a 40a 0.4% 0.8% 1% 4.98v to 5.02v pfc375-3004 +12v 11.3v to 12.6v 10a 16a 0.9% 0.9% 1% 11.9v to 12.1v 24v 22.0v to 28.0v 3a 3a 0.5% 0.8% 1% 23.8v to 24.2v +5v 4.5v to 5.5v 3.5 - 40a 40a 0.4% 0.8% 1% 4.98v to 5.02v pfc375-4000 +12v 11.3v to 12.6v 10a 16a 0.9% 0.9% 1% 11.9v to 12.1v 12v 11.3v to 12.6v 6a 6a 0.9% 0.9% 1% 11.9v to 12.1v 5v 4.9v to 5.1v 3a 3a 2% 2% 2.4% 4.9v to 5.1v single output model selection chart model output adjustment maximum output line load ripple & noise initial setting voltage range current (note 1) regulation regulation %p-p (note 2) accuracy pfc375-1012 12v 10.8v to 13.5v 30a 0.2% 0.8% 1% 11.94v to 12.06v pfc375-1015 15v 12.0v to 17.0v 25a 0.2% 0.6% 1% 14.94v to 15.06v pfc375-1024 24v 21.6v to 26.4v 15a 0.5% 0.8% 1% 23.88v to 24.12v pfc375-1028 28v 25.2v to 30.8v 13.4a 0.5% 0.9% 0.9% 27.86v to 28.14v pfc375-1048 48v 46.0v to 56.0v 7.8a 0.5% 1.0% 1% 47.52v to 48.48v notes: 1) output currents ratings are expressed with 300 lfm forced air. 2) maximum peak to peak noise expressed as a percentage of output voltage, 20mhz bandwidth. rev. 04/2000
2 performance power pfc375 multiple output model selection chart (cont.) - isolated v3 and v4 can be used as positive or negative outputs model output adjustment output peak output line load ripple & noise initial setting voltage range current (note 1) current (note 2) regulation regulation %p-p (note 3) accuracy +5v 4.5v to 5.5v 3.5 - 40a 40a 0.4% 0.8% 1% 4.98v to 5.02v pfc375-4001 +12v 11.3v to 12.6v 10a 16a 0.9% 0.9% 1% 11.9v to 12.1v 12v 11.3v to 12.6v 6a 6a 0.9% 0.9% 1% 11.9v to 12.1v 12v 11.0v to 16.0v 3a 3a 0.9% 0.9% 1% 11.9v to 12.1v +5v 4.5v to 5.5v 3.5 - 40a 40a 0.4% 0.8% 1% 4.98v to 5.02v pfc375-4002 +12v 11.3v to 12.6v 10a 16a 0.9% 0.9% 1% 11.9v to 12.1v 12v 11.3v to 12.6v 6a 6a 0.9% 0.9% 1% 11.9v to 12.1v 24v 22.0v to 28.0v 3a 3a 0.5% 0.8% 1% 23.8v to 24.2v +5v 4.5v to 5.5v 3.5 - 40a 40a 0.4% 0.8% 1% 4.98v to 5.02v pfc375-4004 +12v 11.3v to 12.6v 10a 16a 0.9% 0.9% 1% 11.9v to 12.1v 15v 14.2v to 15.8v 4a 4a 0.7% 0.7% 1% 14.9v to 15.1v 15v 14.2v to 15.8v 4a 4a 0.7% 0.7% 1% 14.9v to 15.1v +5v 4.5v to 5.5v 3.5 - 40a 40a 0.4% 0.8% 1% 4.98v to 5.02v pfc375-4005 +12v 11.3v to 12.6v 10a 16a 0.9% 0.9% 1% 11.9v to 12.1v (note 4) 24v 22.0v to 28.0v 3a 3a 0.5% 0.8% 1% 23.8v to 24.2v 24v 22.0v to 28.0v 3a 3a 0.5% 0.8% 1% 23.8v to 24.2v +24v 21.5v to 26.4v 1 - 10a 10a 0.5% 0.8% 1% 23.8v to 24.2v pfc375-4200 +5v 4.5v to 5.5v 10a 16a 0.4% 0.8% 1% 4.98v to 5.02v 12v 11.4v to 12.6v 4a 4a 0.5% 1% 1% 11.9v to 12.1v 12v 11.4v to 12.6v 4a 4a 0.5% 1% 1% 11.9v to 12.1v +24v 21.5v to 26.4v 1 - 10a 10a 0.5% 0.8% 1% 23.8v to 24.2v pfc375-4201 +5v 4.5v to 5.5v 10a 16a 0.4% 0.8% 1% 4.98v to 5.02v 15v 14.2v to 16.0v 4a 4a 0.5% 0.8% 1% 14.9v to 15.1v 15v 13.7v to 16.0v 4a 4a 0.5% 0.8% 1% 14.9v to 15.1v +5v 4.5v to 5.5v 3.5 - 50a 50a 0.4% 0.8% 1% 4.98v to 5.02v pfc375-4500 +12v 11.3v to 12.6v 10a 16a 0.9% 0.9% 1% 11.9v to 12.1v 12v 11.3v to 12.6v 6a 6a 0.9% 0.9% 1% 11.9v to 12.1v 5v 4.5v to 5.5v 3a 3a 2% 0.9% 1% 4.9v to 5.1v notes: 1) output currents ratings are expressed with 300 lfm forced air. 2) peak loads up to 450 watts for 60 seconds or less are acceptable, (10% duty cycle max.). peak power must not exceed 450 wa tts. 3) maximum peak to peak noise expressed as a percentage of output voltage, 20mhz bandwidth. 4) v3 and v4 may be series connected to obtain 48v. input specifications parameter conditions/description min nom max units input voltage - ac continuous input range. 85 264 vac input frequency ac input. 47 63 hz brown out protection lowest ac input voltage that regulation is maintained with full rated loads. 85 vac hold-up time over full ac input voltage range at full rated load. 20 ms input current 85 vac at full rated load. 6a rms input protection non-user serviceable internally located ac input line fuse, f10a, 250v. inrush surge current internally limited by thermistor, one cycle, 25?. 110 vac 35 a pk 220 vac 65 power factor per en61000-3-2. 0.98 w/va operating frequency switching frequency of main transformer. 100 khz advanced product release
3 performance power pfc375 output specifications parameter conditions/description min nom max units efficiency full rated load, 110 vac. varies with distribution of loads among outputs. 68 % minimum loads single output models. 0 multiple output models, 5v main output only. 3.5 amps multiple output models, 24v main output only. 1 ripple and noise full load, 20mhz bandwidth. see model selection charts output power 300 lfm forced air cooling required for operation. see optional fan. continuous power, multiple output models. 375 watts peak power, all models. 450 overshoot / undershoot output voltage overshoot/undershoot at turn-on. 0 v regulation varies by output. total regulation includes: line changes from 85-132 vac or see model selection charts 170-264 vac, changes in load starting at 20% load and changing to 100% load. transient response recovery time, to within 1% of initial set point due to a 50-100% load change, 1ms 3% max. deviation. (main output only on multi-output units). turn-on delay time required for initial output voltage stabilization. 1 sec turn-on rise time time required for output voltage to rise from 10% to 90%. 10 ms interface signals and internal protection parameter conditions/description min nom max units overvoltage protection provided on single output units and the main output only of multiple output units. pfc375-30xx, pfc375-40xx, pfc375-45xx 6.0 6.4 pfc375-1012 13.5 15.5 pfc375-1015 17.0 19.5 pfc375-1024 27.0 30.7 v pfc375-1028 30.8 35.0 pfc375-1048 60.0 70.0 pfc375-42xx 27.0 30.7 overload protection fully protected against output overload and short circuit. automatic recovery upon removal of overload condi tion. overtemperature protection system shutdown due to excessive internal temperature, automatic reset. remote sense total voltage compensation for cable losses with respect to the main output. 250 mv current share accuracy of shared current with up to 6 parallel units. 10 % inhibit ttl compatible logic signal will inhibit outputs by the application of a logic low signal. an open circuit or external ttl high signal allows normal operation. input power ttl compatible logic signal. time before regulation dropout due to 5ms fail warning loss of input power at 110 vac. power good ttl compatible signal. signal is low if main output is greater or less than 10% of nominal. fan voltage provides 170ma current to user supplied fan if fan option is not selected. 12 v safety, regulatory, and emi specifications parameter conditions/description min nom max units agency approvals ul1950. csa 22.2 no. 234/950. approved en60950 (t?v). dielectric withstand voltage input to output. 2600 vdc electromagnetic interference fcc cfr title 47 part 15 sub-part b - conducted. b class en55022 / cispr 22 conducted. b esd susceptibility per en61000-4-2, level 4. 8 kv radiated susceptibility per en61000-4-3, level 3. 10 v/m eft/burst per en61000-4-4, level 4. ? kv input transient protection per en61000-4-5 class 3. line to line 1 kv line to ground 2 insulation resistance input to output. 10 m ? leakage current per en60950, 264 vac. 2.0 ma
4 environmental specifications parameter conditions/description min nom max units altitude operating. 10k asl ft. non-operating. 40k asl ft. operating temperature at 100% load 0 50 c derate linearly above 50? by 2.5% per ?. at 50% load 0 70 c storage temperature -55 85 c forced air cooling forced air cooling of 300 lfm is required if the internal fan option is not specified. cooling air velocity is measured 1/4" above, at the middle of the chassis. airflow direction is from the input section to the output section. temperature coefficient 0? to 70? (after 15 minute warm-up). ?.02 ?.05 %/? relative humidity non-condensing. 5 95 %rh shock operating: 10?msec, 3 axis, half sine. 20 g non-operating: 10?msec, 3 axis, half sine. 40 vibration operating: 5-32hz 0.02 in (da) 32-2000hz sinusoidal 1 g rms non-operating: 6.15 g rms options description notes size impact fan add ??as a suffix to the model number to order integral fan. 10.50" x 5.00" x 2.50" (provides required 300 lfm of forced air cooling). (266.7mm x 127.0mm x 63.5mm) metric mounting add ??as a suffix to the model number to order chassis with 9.00" x 5.00" x 2.50" m4 x 0.7 mounting inserts. (228.6mm x 127.0mm x 63.5mm) performance power pfc375 nuclear and medical applications power-one products are not authorized for use as critical components in life support systems , equipment used in hazardous environments, or nuclear control systems without the express written consent of the president of power-one, inc. technical revisions the appearance of products, including safety agency certifications pictured on labels, may change dependin g on the date manufactured. specifications are subject to change without notice.
5 performance power pfc375 overall size: 9.00" x 5.00" x 2.50" (228.6mm x 127.0mm x 63.5mm) overall length with fan: 10.50" (266.7mm) weight: 4.3 lbs (1.95 kg) input & output connections: 6-32 screw terminal on 0.375" (9.5mm) centers bus bar main output, e1 & e2, 10-32 screw terminal chassis: 0.090" (2.3mm) aluminum alloy, with clear finish j3 j4 pin 4 n/c pin 3 pwr good pin 2 pf pin 1 sig gnd pin 4 +fan 8-32 flush nut 8 places both sides typ. with metric mounting option: m4 x 0.7, 8 places fan option fan option chassis gnd ac-n ac-l 3 1 tb1 pins 3 & 4 (v1) pins 1 & 2 (v1) rtn pin 5 pin 6 customer connection: p4,p3,p5 mating housing: molex 5051 p4,p3,p5 mating terminals: molex 4809 or 40445 j5 +share n/c (v2) rtn (v2) pin 7 v1 adj (v4) rtn (v4) (v3) rtn pin 10 pin 9 pin 8 tb3 1 v2 adj v4 adj v3 adj (v3) pin 1 +sense pin 2 ?sense pin 3 inhibit 3 . 900" (99 . 1mm) 0 . 70" (17 . 8mm) 5 . 00" (127 . 0mm) 2 . 50" (63 . 5mm) 1 . 20" (30 . 4mm) 1 . 50" (38 . 1mm) 6.50" (165.1mm) 1 . 25" (31 . 8mm) 9.00" (228.6mm) e2 pin 1 pin 2 e1 1 (v2) rtn (v2) (v1) rtn pin 3 v1 adj (v4) rtn (v4) (v3) rtn pin 6 pin 5 pin 4 tb2 v2 adj v4 adj v3 adj (v3) bus bar main output terminal block main output (pfc375-4200, pfc375-4201, and all single output units except pfc375-1005) (v1) 3.12" (79.2mm) suggested air flow (bottom view) (top view)
|
