06/97 n/al 9.11. 001.01 our policy is one of continuous research and development. we therefore reserve the right to amend, without notice, the specifications given in this document. ordering information to order, quote appropriate product number from the tables on the following pages. product numbering system is designed to make identification and selection simple: l very compact units l easy tube insertion for rapid assembly of pneumatic circuits l positive tube anchorage l simpler pneumatic systems l eliminates need for electrical reed switches technical data medium: compressed air operating pressure: cylinder pressure (pc) 10 bar max sensor supply pressure 3 - 10 bar sensor switch pressure 1.0 bar typ. operating temperature: ?0? to +80? body ports 4mm push-in fittings 5 32 push-in fittings 1 8, 1 4 bspp banjo bolt 1 8, 1 4 nptf banjo bolt tube sizes 4mm o/d 5 32 o/d tubing types: nylon 11 or 12, polyurethane and other plasticised or unplasticised tubing which conforms to the tolerances specified in bs 5409, part 1, 1976, light and normal duty, din 73378, din 74234, nfe 49-100 materials delrin 100 and plastic parts glass filled nylon nickel plated brass collet nitrile and polyurethane elastomeric parts nickel plated brass banjo bolt pneumatic function fittings metric & inch pressure sensor fitting thread size/ tube size tube size/ thread size shape type series number 10 102gd 124gd
n/al 9.1 1. 001.0 2 06/97 pneumatic function fittings our policy is one of continuous research and development. w e therefore reserve the right to amend, without notice, the specifications given in this document. w arning these products are intended for use in industrial compressed air systems only . do not use these products where pressures and temperatures can exceed those listed under ? echnical data . before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or o ther applications not within published specifications, consult norgren. through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. the system designer is w arned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent pe rsonal injury or damage to equipment in the event of such failure. system designers must provide a warning to end users in the system instructional manual if protection against a failure mode ca nnot be adequately provided. system designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with th ese products where applicable. d e c i a f h j b g a 1 2 pif x bspp banjo bolt pressure sensor fitting- 102gd this sensor fitting produces an end of stroke signal when exhaust back pressure in a c ylinder decays belo w a set value. it should be mounted directly on the c ylinder and can be used with a flo w control device mounted into the top port. it is recommended tha t the sensor supply pressure to port 1 be the same as the nominal working pressure of the c ylinder . d e c i a f h j b g a 1 2 pif x nptf banjo bolt pressure sensor fitting- 124gd product a b c d e f g h i j number o/d thread thread a/f tube nptf nptf 124gd0218 5 32 " 1 8 " 8,5 45,2 1 8 " 9,5 9,5 21,0 28,5 9 16 " 124gd0228 5 32 " 1 4 " 10,5 47,2 1 4 " 9,5 14,3 21,0 33,7 3 4 " this sensor fitting produces an end of stroke signal when exhaust back pressure in a c ylinder decays belo w a set value. it should be mounted directly on the c ylinder and can be used with a flo w control device mounted into the top port. it is recommended tha t the sensor supply pressure to port 1 be the same as the nominal working pressure of the c ylinder . product a b c d e f g h i j number o/d thread thread a/f tube bspp bspp 102gd0418 4 1 8 " 8,5 45,2 1 8 " 9,5 5,6 21,0 24,9 15 102GD0428 4 1 4 " 10,5 47,2 1 4 " 9,5 6,5 21,0 29,0 19
|
