sy84403bl ultra small 3.3v 4.25gbps cml low - power limiting post amplifier with ttl los mlf and micro leadframe are registered trademarks of amkor technology. micrel inc. ? 2180 fortune drive ? san jose, ca 95131 ? usa ? tel +1 (408) 944 - 0800 ? fax + 1 (408) 474 - 1000 ? http://www.micrel.com may 2009 m9999 - 051509-a hbwhelp@micrel.com or (408) 955 - 1690 general description the sy84403bl is the industry?s smallest limiting post amplifier ideal for compact copper and fiber optic module applications . the device connects to typical transimpedance amplifiers (tias). the linear signal output from tias can con tain significant amounts of noise and may vary in amplitude over time. the sy84403bl quantizes these signals and outputs typically 800mv pp voltage - limited waveforms. the sy84403bl comes in a tiny 10 - pin 2x2 mlf ? package, which is unparalleled in the indus try. it offers space savings of 55% or more over typical post amps. it operates from a single +3.3v 10% power supply, over an industrial temperature range of ? 40c to +85c. with its wide bandwidth and high gain, signals with data rates up to 4.25gbps and as small as 10mv pp can be amplified to drive devices with cml inputs or ac - coupled pecl inputs. the sy84403bl incorporates a loss - of - signal (los) open- collector ttl output with internal 4.75k ? pull - up resistor. a programmable loss - of - signal level set pin (loslvl) sets the sensitivity of the input amplitude detection. los asserts high if the input amplitude falls below the threshold set by loslvl and de - asserts low otherwise. los can be fed bac k to the enable bar (/en) input to maintain output stability under a loss of signal condition. /en de - asserts the true output signal without removing the input signal. all support documentation can be found on micrel?s web site at: www.micrel.com . typical performance features ? available in an ultra small 10 - pin (2mm x 2mm) mlf ? package ? multi - rate up to 4.25gbps operation ? 10mv pp input sensitivity ? low noise 50 ? cml data outputs ? 800mv pp differential output swing ? 60ps edge rates ? 1ps rms typ. random jitter ? 10ps pp typ. deterministic jitter ? chatter - free loss - of - signal (los) output ? 3.5db electrical hysteresis ? oc - ttl output with internal 4. 75k ? pull - up resistor ? programmable los sensitivity using single external resistor ? internal 50 ? data input termination ? ttl /en input allows feedback from los ? wide operating range: ? single 3.3v 10% power supply ? industrial temperature range: ? 40c to +85c ? part of micrel?s new ultra small fom ic family. for laser diode drivers, see sy84202l or sy84402l applications ? 1.062gbps, 2.125gbps and 4.25gbps fibre channel ? cable driver ? sff and sfp transceivers ? high - gain line driver and line receiver markets ? copp er interconnect ? datacom and telecom ? storage area network (san)
micrel, inc. sy84403bl may 2009 2 m9999 - 051509-a hbwhelp@micrel.com or (408) 955 - 1690 typical application functional block diagram
micrel, inc. sy84403bl may 2009 3 m9999 - 051509-a hbwhelp@micrel.com or (408) 955 - 1690 ordering information (1) part number package type operating range package marking lead finish SY84403BLMGTR mlf -10 industrial 403 with pb - free bar - line indicator nipdau pb - free notes: 1. contact factory for die availability. dice are guaranteed at t a = 25c, dc electricals only. pin configuration 10- pin mlf ? (mlf - 10) pin description pin number pin name type pin function 1, 2 din, /din differential data input differential data input. each pin internally terminates to ref through 50?. 3 vref reference voltage. bypass with 0.01f low esr capacitor from v ref to v cc to stabilize los lvl and v ref . 4 loslvl input: default is maximum sensitivity loss -of - signal lev el set: a resistor from this pin to vcc sets the threshold for the data input amplitude at which the los output will be asserted. 5 gnd exposed pad ground device ground. exposed pad must be soldered (or equivalent) to the same potential as the ground pi n. 6 los ttl output loss -of - signal: asserts high when the data input amplitude falls below the threshold set by loslvl. contains internal 4 .75k ? pull - up resistor 8, 7 dout, /dout differential cml output differential data output. 9 vcc power supply positive power supply. bypass with 0.1f||0.01f low esr capacitors. 0.01f capacitors should be as close as possible to vcc pin. 10 /en ttl i nput: default is high enable bar: de - asserts true data output when high. incorporates 25k ? pull - up to v cc .
micrel, inc. sy84403bl may 2009 4 m9999 - 051509-a hbwhelp@micrel.com or (408) 955 - 1690 absolute maximum ratings (1) supply voltage (v cc ) ..................................... 0v to 4 .0v /en, loslvl voltage ........................................ 0 to v cc ref current ......................................................... 1ma los current ......................................................... 5ma dout, /dout current ....................................... 25ma din, /din current ............................................... 10ma lead temperature (soldering, 20sec.) ................ 260c storage temperature (t s ) .................. ? 65c to +150c operating ratings (2) supply voltage (v cc ) .............................. +3.0v to +3.6v ambient temperature (t a ) .................... ? 40c to +85c junction temperature (t a ) .................. ? 40c to +125c p ackage thermal resistance (3) mlf ? ja (still - air) ............................................ 93c/w jb .......................................................... 56c/w dc electrical characteristics v cc = +3.0v to +3.6v; t a = ? 40c to +85c; typical values at v cc = +3.3v, t a = 25c. symbol parameter condition min typ max units i cc power supply current note 4 25 42 ma note 5 41 62 ma v ref ref voltage v cc ? 1.3 v v loslvl loslvl voltage range v ref v cc v v oh dout, /dout high voltage note 6 v cc ? 0.020 v cc ? 0.005 v cc v v ol dout, /dout low voltage v cc = 3.3v, note 6 v cc ? 0.475 v cc ? 0.400 v cc ? 0.350 v v offset differential output o ffset 80 mv z o single - ended output impedance 40 50 60 ? z i single - ended input impedance 40 50 60 ? ttl dc electrical characteristics v cc = +3.0v to +3.6v; t a = ? 40c to +85c. symbol parameter condition min typ max units v oh los output high level sourcing 100a 2.4 v cc v v ol los output low level sinking 2ma 0.5 v v ih /en input high voltage 2.0 v v il /en input low voltage 0.8 v i ih /en input high current v in = 2.7v v in = v cc 20 100 a a i il /en input low current v in = 0.5v ? 0.3 ma notes: 1. permanent device damage may occur if ratings in the absolute maximum ratings section are exceeded. this is a stress rating only and functional operation is not implied for conditions other than those detailed in the operational sections of this data sheet. exposure to absolute maximum ratings condit ions for extended periods may affect device reliability. 2. the data sheet limits are not guaranteed if the device is operated beyond the operating ratings. 3. thermal performance assumes are of 4 - layer pcb. exposed pad must be soldered (or equivalent) to the device's most negative potential on the pcb. 4. excludes current of cml output stage. see ?detailed description.? 5. total device current with no output load. 6. if the load impedance is different, the output level will be changed. amplifier is in limi ting mode.
micrel, inc. sy84403bl may 2009 5 m9999 - 051509-a hbwhelp@micrel.com or (408) 955 - 1690 ac electrical characteristics v cc = +3.0v to +3.6v; t a = ? 40c to +85c; r l = 50 ? to v cc ; typical values at v cc = +3.3v, t a = 25c. symbol parameter condition min typ max units t r, t f output rise/fall time (20% to 80%) note 7 60 120 ps t jit ter deterministic random note 8 note 9 10 1 ps pp ps rms v id differential input voltage swing see figure 1 10 1800 mv pp v od_ac ac differential output voltage note 10 600 800 950 mv pp t off los release time 2 10 s t on los assert time 2 10 s los a l low los assert level r loslvl = 15k ?, note 11 8 mv pp los dl low los de - assert level r loslvl = 15k ?, note 11 12 mv pp hsy l low los hysteresis r loslvl = 15k ?, note 12 2 3.5 4.5 db los am medium los assert level r loslvl = 5k ?, note 11 12 17 mv pp los dm medium los de - assert level r loslvl = 5k ?, note 11 25 33 mv pp hsy m medium los hysteresis r loslvl = 5k ?, note 12 2 3.5 4.5 db los ah high los assert level r loslvl = 100 ?, note 11 34 47 mv pp los dh high los de - assert level r loslvl = 100 ?, note 11 70 83 mv pp hsy h high los hysteresis r loslvl = 100 ?, note 12 2 3.5 4.5 db v sr los sensitivity range 10 35 mv pp a v(diff) differential voltage gain 32 38 db s 21 single - ended small - signal gain 26 32 db notes: 7. amplifier in limiting mode. input is a 200mhz square wave. 8. deterministic jitte r measured using 4.25gbps k28.5 pattern, v id = 20mv pp . 9. random jitter measured using 4.25gbps k28.7 pattern, v id = 20mv pp . 10. differential output swing measured at 4.25gbps with 20mvpp input and prbs - 23 data pattern and 50 ? load. 11. see ?typical opera ting characteristics? for a graph showing how to choose a particular r loslvl for a particular los assert and its associated de- assert amplitude. 12. this specification defines electrical hysteresis as 20log(los de - assert/los assert). the ratio between opti cal hysteresis and electrical hysteresis is found to vary between 1.5 and 2 depending on the level of received optical power and rosa characteristics. base d on that ratio, the optical hysteresis corresponding to the electrical hysteresis range 2db - 4.5 db s hown in the ac characteristics table will be 0.5db - 3db optical hysteresis.
micrel, inc. sy84403bl may 2009 6 m9999 - 051509-a hbwhelp@micrel.com or (408) 955 - 1690 typical operating characteristics 25 30 35 40 45 50 55 60 -40 -15 10 35 60 85 temperature (c) power supply current vs. temperature 700 720 740 760 780 800 820 840 860 880 900 -40 -15 10 35 60 85 temperature (c) differential output voltage swing vs. temperature (amplifier in limiting mode) 0 100 200 300 400 500 600 700 800 900 0 5 10 15 20 25 30 35 40 45 50 v id (mv pp ) differential output voltage swing vs. differential input voltage swing r loslvl (k ) r loslvl (k )
micrel, inc. sy84403bl may 2009 7 m9999 - 051509-a hbwhelp@micrel.com or (408) 955 - 1690 detailed description the sy84403bl low - power limiting post amplifier operates from a single +3.3v power supply, over t emperatures from ? 40c to +85c. signals with data rates up to 4.25gbps and as small as 10mv pp can be amplified. figure 1 shows the allowed input voltage swing. the sy84403bl generates an los output, allowing feedback to /en for output stability. loslvl se ts the sensitivity of the input amplitude detection. sy84403bl is available in the industry?s smallest form factor, a tiny 10 - pin (2mm x 2mm) mlf ? package. it is part of micrel?s new family of ultra - small fiber optic ics. input amplifier/buffer the sy8440 3bl?s inp uts are internally terminated with 50? - to - ref. if not affected by this internal termination scheme, upstream devices need to be ac - coupled to the sy84403bl's inputs. figure 2 shows a simplified schematic of the input stage. the high - sensitivity of the inpu t amplifier allows signals as small as 10mv pp to be detected and amplified. the input amplifier allows input signals as large as 1800mv pp . input signals are linearly amplified with a typically 38db differential voltage gain. since it is a limiting amplifie r, the sy84403bl outputs typically 800mv pp voltage - limited waveforms for input signals that are greater than 20mv pp . applications requiring the sy84403bl to operate with high - gain should have the upstream tia placed as close as possible to the sy84403bl?s input pins to ensure the best performance of the device. output buffer the sy84403bl?s cml output buffer is designed to drive 50 ? lines. the output buffer requires appropriate termination for proper operation. an external 50 ? resistor to v cc or equivalent for each output pin provides this. figure 3 shows a simplified schematic of the output stage and includes an appropriate termination method. of course, driving a downstream device with a cml input that is internally terminated with 50 ? - to - v cc eliminates th e need for external termination. as noted in the previous section, the amplifier outputs typically 800mv pp waveforms across 25 ? total loads. the output buffer thus switches typically 16ma tail - current. figure 4 shows the power supply current measurement, w hich excludes the 16ma tail - current. loss - of - signal the sy84403bl incorporates a chatter - free loss - of - signal (los) open - collector ttl output with internal 4.75k ? pull - up resistor as shown in figure 5. los is used to determine that the input amplitude is t oo small to be considered a valid input. los asserts high if the input amplitude falls below the threshold set by loslvl and de - asserts low otherwise. los can be fed back to the enable (/en) input to maintain output stability under a loss of signal conditi on. /en de - asserts low the true output signal without removing the input signals. typically, 3.5db los hysteresis is provided to prevent chattering. loss - of - signal level set a programmable loss - of - signal level set pin (loslvl) sets the threshold of the inp ut amplitude detection. connecting an external resistor between v cc and loslvl sets the voltage at loslvl. this voltage ranges from v cc to v ref . the external resistor creates a voltage divider between v cc and vref as shown in figure 6. if desired, an appro priate external voltage may be applied rather than using a resistor. the relationship between v loslvl and r loslvl is given by: ? ? ? ? ? ? ? ? + ? = 2.8 r r 1.3 v v loslvl loslvl cc loslvl where voltages are in volts and resistances are in k ?. the smaller the external resistor, implying a smaller voltage difference from loslvl to vcc, lowers the los sensitivity. hence, larger input amplitude is required to de - assert los. ?typical operating c haracteristics? contains graphs showing the relationship between the input amplitude detection sensitivity and r loslvl . hysteresis the sy84403bl typically provides 3.5db los electrical hysteresis. by definition, a power ratio measured in db is 10log (power ratio). power is calculated as v in 2 /r for an electrical signal. hence, the same ratio can be stated as 20log (voltage ratio). while in linear mode, the electrical voltage input changes linearly with the optical power and hence the ratios change linearly. therefore, the optical hysteresis in db is half the electrical hysteresis in db given in the datasheet. the sy84403bl provides typically 1.75db los optical hysteresis. as the sy84403bl is an electrical device, this datasheet refers to hysteresis in electri cal terms. with 3.5db los hysteresis, a voltage factor of 1.5 is required to de- assert los.
micrel, inc. sy84403bl may 2009 8 m9999 - 051509-a hbwhelp@micrel.com or (408) 955 - 1690 figure 1. v is and v id definition figure 2. input structure figure 3. output structure
micrel, inc. sy84403bl may 2009 9 m9999 - 051509-a hbwhelp@micrel.com or (408) 955 - 1690 figure 4. power supply current measurement figure 5. los output structure figure 6. loslvl setting circuit related product and support documentation part number function datasheet link application notes notes on sensitivity and hysteresis in micrel post amplifier www.micrel.com/product - in fo/app_hints+notes.shtml
micrel, inc. sy84403bl may 2009 10 m9999 - 051509-a hbwhelp@micrel.com or (408) 955 - 1690 package information 10- pin micro leadframe ? (mlf -10) micrel, inc. 2180 fortune drive san jose, ca 95131 usa tel +1 (408) 944 - 0800 fax +1 (408) 474 - 1000 web http://www.micrel.com the information furnished b y micrel in this data sheet is believed to be accurate and reliable. however, no responsibility is assumed by micrel for its use. micrel reserves the right to change circuitry and specifications at any time without notification to the customer. micrel pro ducts are not designed or authorized for use as components in life support appliances, devices or systems where malfunction o f a product can reasonably be expected to result in personal injury. life support devices or systems are devices or systems that (a ) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to res ult in a significant injury to the user. a purchaser?s use or sale of micrel products for use in life support ap pliances, devices or systems is a purchaser?s own risk and purchaser agrees to fully indemnify micrel for any damages resulting from such use or sale. ? 2009 micrel, incorporated.
|
