View C070FW01V0_1572746.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

version 0.9 total pages 23 date 17 dec, 2007 rohs compliance product specification 7 color tft-lcd module ( ) preliminary specification ( ) final specification model name: c070fw 01 v0 no te : t h e c on te n t of th is s pec if ic a t io n is s u bj ec t t o c ha n ge . ? 2 00 6 au o ptr o nic s al l r i gh ts res er v e d , d o n ot c op y. www..net
record of revision version revise date p a g e content draft 0 06.mar, 2006 0 first draft. draft 0.1 20.nov, 2006 6 update lamp current maximum value to 6.5marms draft 0.2 03.may, 2007 0 rohs compliance 3 display resolution C 480rgbx234; gray scale inversio n 5 ccfl C vl (3000vrms); storage/operation temp. ra nge 5 note 2 : add mod 6 v-com ac component ; note 2; note 3; 6 discharge stablization time 3 min. 8 note 3 for partial mode(4:3) 9 power sequence t5h Q 25ms; t8 R 1.5ms 10 add ntsc ratio 12 add testing regulation; add cycle time for vibra tion 14,15 update drawing draft 0.3 18.may,2007 5 update maximum operation temp. 6 add mod into note 2 --- electrical charisterics 12 reliability test items (note 2) ? note 3 draft 0.4 29.jun,2007 13 packing form updates draft 0.5 5. sep,2007 14 update tft-lcd module ccfl h/low voltage connector draft 0.6 2. oct,2007 15 update tft lcd module drawing draft 0.7 15. oct,2007 6 typical operating conditions (gnd=avss=0v, note 3) 6 backlight driving conditions (self-heating type) C note 1, note 3 8 timing condition 9 power sequence format 12 reliability test C add note 1&2 www..net
19 delete tdrgb 23 fig 7 the setup and hold time definition draft 0.8 16. nov,2007 7 ac timing. updates of timing conditions. 0.9 17 dec,2007 6 vcc voltage updates www..net
model c070fw01 v0 version : 0.9 9 page : 1 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. contents: a. physical specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p3 b. electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p4 1. pin assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p4 a.tft-lcd panel driving section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p5 b.backlight driving section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p5 2.absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p5 3. electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p6 a. typical operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p6 b. current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p6 c. backlight driving conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p6 4. ac timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p7 a. timing conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p7 b. timing diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p7 c. optical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p10 d. reliability test items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p12 e. packing form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p13 www..net
model c070fw01 v0 version : 0.9 9 page : 2 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. appendix: fig.1 outline dimension of tft-lcd module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p14 fig.2 outline dimension of tft-lcd module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p15 fig.3 sampling clock timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p16 fig.4 horizontal display timing range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p17 fig.5-(a) horizontal timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p18 fig.5- (b) detail horizontal timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p19 fig.6 vertical shift clock timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p20 fig.6- (a) vertical timing (from up to down) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p21 fig.6-(b) vertical timing (from down to up) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . p22 fig.7 setup and hold time definition between cph1 a nd analog signal vr timing p23 www..net
model c070fw01 v0 version : 0.9 9 page : 3 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. a. physical specifications no. item specification remark 1 display resolution(dot) 480rgb(w) 234(h) 2 active area(mm) 154.08(w) 86.58(h) 3 screen size(inch) 7.0(diagonal) 4 dot pitch(mm) 0.107(w) 0.370(h) 5 color configuration r. g. b. stripe 6 overall dimension(mm) 164.9(w) 100.0(h) 6.0(d) note 1 7 weight(g) 160 10 8 surface treatment ag (25%) with swv film 9 backlight unit ccfl 10 gray scale inversion 6 oclock note 1: refer to fig. 1 www..net
model c070fw01 v0 version : 0.9 9 page : 4 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. b. electrical specifications 1.pin assignment a. tft-lcd panel driving section pin no symbol i/o description remark 1 gnd - ground for logic circuit 2 v cc i supply voltage of logic control circuit for scan driver 3 v gl i negative power for scan driver 4 v gh i positive power for scan driver 5 stvr i/o vertical start pulse note 1 6 stvl i/o vertical start pulse note 1 7 ckv i shift clock input for scan driver 8 u/d i up/down scan control input note 1,2 9 oev i output enable input for scan driver 10 vcom i common electrode driving signal 11 vcom i common electrode driving signal 12 l/r i left/right scan control input note 1,2 13 mod i sequential sampling and simultaneous sampl ing setting note 3 14 oeh i output enable input for data driver 15 sthl i/o start pulse for horizontal scan line note 1 16 sthr i/o start pulse for horizontal scan line note 1 17 cph3 i sampling and shifting clock pulse for dat a driver 18 cph2 i sampling and shifting clock pulse for dat a driver 19 cph1 i sampling and shifting clock pulse for dat a driver 20 v cc i supply voltage of logic control circuit for data driver 21 gnd - ground for logic circuit 22 vr i alternated video signal input(red) 23 vg i alternated video signal input(green) 24 vb i alternated video signal input(blue) 25 av dd i supply voltage for analog circuit 26 av ss - ground for analog circuit note 1: selection of scanning mode (please refer to the following table) setting of scan control input in/out state for start pulse u/d l/r stvr stvl sthr sthl scanning direction gnd v cc out in out in from up to down, and from left to right. v cc gnd in out in out from down to up, and from right to left. gnd gnd out in in out from up to down, and from right to left. www..net
model c070fw01 v0 version : 0.9 9 page : 5 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. v cc v cc in out out in from down to up, and from left to right. in: input; out: output. note 2: definition of scanning direction. refer to figure as below: note 3: mod = h: simultaneous sampling. mod = l: sequential sampling. please set cph2 and cph3 to gnd when mod = h. b. backlight driving section (refer to figure 1) no. symbol i/o description remark 1 hi i power supply for backlight unit (high voltag e) -- 2 gnd - ground for backlight unit -- 2. absolute maximum ratings item symbol condition min. max. unit remark v cc gnd=0 -0.3 7 v av dd av ss =0 -0.3 7 v v gh -0.3 18 v v gl gnd=0 -15 0.3 v power voltage v gh v gl - 33 v v i -0.3 av dd +0.3 v note 1 v i -0.3 v cc +0.3 v note 2 input signal voltage vcom -2.9 5.2 v v l 3,000 vrms ccfl i l 10 ma operation -30 +85 c note 3 temp. range storage -40 +95 c note 1: vr, vg, vb. note 2: sthl, sthr, oeh, l/r, cph1~cph3, stvr, stvl , oev, ckv, u/d, mod note 3: operation temp. range means ambient temp. www..net
model c070fw01 v0 version : 0.9 9 page : 6 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. 3. electrical characteristics a. typical operating conditions (gnd=avss=0v, note 3) item symbol min. typ. max. unit remark v cc 3 3.3 5.2 v note 4 av dd 4.5 5 5.5 v v gh 14.3 15 15.7 v power supply v gl -10.5 -10 -9.5 v v ia 0.4 - av dd -0.4 v note 1 v iac - 3 - v ac component video signal amplitude (vr,vg,vb) v idc - av dd /2 - v dc component v cac 3.5 5.6 6.5 vp-p ac component vcom v cdc 1.4 1.7 2.0 v dc component h level v ih 0.8 v cc - v cc v input signal voltage l level v il 0 - 0.2 v cc v note 2 note 1: refer to fig.4- (a). note 2: sthl, sthr, oeh, l/r, cph1~cph3, stvr, stvl , oev, ckv, u/d,mod note 3: be sure to apply gnd, v cc and v gl to the lcd first, and then apply v gh . note 4: if input signal amplitude is 3.3v, recommend value for vcc is 3.3v; if input signal amplitude is 5v, recommend value for vcc is 5v b. current consumption (gnd=avss=0v) parameter symbol condition min. typ. max. unit remark i gh v gh =15v - 0.20 0.5 m a i gl v gl =-10v - 0.80 1.5 m a i cc v cc =5v - 3.0 6.0 m a current for driver i dd av dd =5v - 17.0 30 m a c. backlight driving conditions (self-heating type) C not e 1, note 3 parameter symbol min. typ. max. unit remark lamp voltage v l 513 570 627 vrms lamp current i l - 6 6.5 marms frequency f l 50 - 80 khz note 2 - 890 1,110 vrms ta = 25 ,note 4 - 1,160 1,440 vrms ta = 0 ,note 4 lamp starting voltage v s - 1,500 1,870 vrms ta = -30 ,note 4 discharge stabilization time ts 3 min discharge time lag td 1 sec note 5 lamp life time 10,000 - - hr note 6 note 1: panel surface temperature should be kept le ss than content of 2. absolute maximum ratings" note 2: the lamp frequency should be selected as di fferent as possible from display horizontal synchronous signal to avoid interference . (reference value) www..net
model c070fw01 v0 version : 0.9 9 page : 7 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. note 3: values of lamp voltage, lamp power consumpt ion and starting voltage are defined on condition of the lcd module derived by nf[as-114b] ci rcuit which measured from connectors of product(as below figure). however thi s isnt the values that we can assure stability of starting lamp on condition that the module is installed in your set. note 4: the max of starting voltage means the min imum voltage to light normally in the lcd module. note 5: the time needed to start discharge when the over 1500vrms voltage is continuously applied to both end of the lamp. before testing, th e lamp is left in the dark room(ambient temperature: 25+/- 2 o c, ambient luminance: less than 0.1lux) for 24hrs afte r lighted for 1minute at lated lamp current. note 6:the lamp life time is defined as the module brightness decrease to 50% original brightness at ta=25 , i l =6ma. 4. ac timing a. timing conditions parameter symbol min. typ. max. unit. remark rising time t r - - 10 ns note 1 falling time t f - - 10 ns note 1 high and low level pulse width t cph 95 103 107 ns cph1~cph3 83.3 ns note 3 cph pulse duty t cwh 40 50 60 % cph1~cph3 cph pulse delay t c12 t c23 t c31 30 t cph /3 t cph /2 ns cph1~cph3 sth setup time t suh 20 - - ns sthr,sthl sth hold time t hdh 20 - - ns sthr,sthl sth pulse width t sth - 1 - t cph sthr,sthl sth period t h 61.5 63.5 65.5 s sthr,sthl oeh pulse width t oeh 0.475 3.48 6.48 s oeh(note 5) sample and hold disable time t dis1 5.5 8.78 8.88 s note 6 oev pulse width t oev 2.0 3.4 6.5 s oev ckv pulse width t ckv 1.0 3.1 4.68 s ckv clean enable time t dis2 1.0 2.2 4.1 s note 7 www..net
model c070fw01 v0 version : 0.9 9 page : 8 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. horizontal display start t sh - 1 - t cph /3 note 8 horizontal display timing range t dh - 480 - t cph /3 note 8 stv setup time t suv 400 - - ns stvu,stvd stv hold time t hdv 400 - - ns stvu,stvd stv pulse width t stv - - 1 t h stvu,stvd note 4 horizontal lines per field t v 256 262 268 t h note 2 vertical display start t sv 3 - t h vertical display timing range t dv 234 - t h vcom rising time t rcom - 5 s vcom falling time t fcom - 5 s vcom delay time t dcom 0 - s setup time of analog t asu 60 ns rgb delay time t drgb 40 - 1 ns note 1: for all of the logic signals. note 2: please dont use odd horizontal lines to dri ve lcd panel for both odd and even field simultaneously. note 3: for partial mode (4:3, side-black) note 4: maximum time is one line period. note 5: the maximum pulse width of oeh should refe r to the minimum of tdis1 and the hsync back porch. note 6: t dis1 is time difference between oeh and sthl note 7: t dis2 is time difference between oev and ckv. note 8: the unit is t cph b. timing diagram please refer to the attached drawing, from fig.2 to fig.6. www..net
model c070fw01 v0 version : 0.9 9 page : 9 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. 5. power sequence (only for reference) power on : power off : www..net
model c070fw01 v0 version : 0.9 9 page : 10 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. c. optical specification (note 1, note 2) item symbol condition min. typ. max. unit remark response time rise fall tr tf =0 - - 12 18 24 36 ms ms note 3,5 contrast ratio cr at optimized viewing angle 200 300 - note 4, 5 viewing angle top bottom left right cr R 10 30 50 50 50 40 60 60 60 - - - - deg . note 5, 6 viewing angle top bottom left right cr R 5 40 60 60 60 50 70 70 70 - - - - deg . note 5, 6 brightness y l i l =6ma, 25 400 500 - cd/m 2 note 7 x =0 0.26 0.31 0.36 white chromaticity y =0 0.28 0.33 0.38 note 7 ntsc ratio =0 48 % note 1 : ambient temperature =25 , and lamp current i l = 6 marms. to be measured in the dark room. dc/ac inverter driving frequency: 70 khz. note 2 :to be measured on the center area of panel with a viewing cone of 1 by topcon luminance meter bm-5, after 15 minutes operation. note 3. definition of response time: the output signals of photo detector are measured wh en the input signals are changed from black to white(falling time) and from whit e to black(rising time), respectively. the response time is defined as the time interval bet ween the 10% and 90% of amplitudes. refer to figure as below. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% www..net
model c070fw01 v0 version : 0.9 9 page : 11 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. note 4. definition of contrast ratio: contrast ratio is calculated with the following formu la. contrast ratio (cr)= note 5. white vi=v i50 1.5v black vi=v i50 2.0v means that the analog input signal swings in phase with v com signal. means that the analog input signal swings out o f phase with v com signal. v i50 : the analog input voltage when transmission is 50% the 100% transmission is defined as the transmission of lcd panel when all the input terminals of module are electrically opened. note 6. definition of viewing angle, refer to figure as below. note 7. measured at the center area of the panel wh en all the input terminals of lcd panel are electrically opened. photo detector output when lcd is at white state photo detector output when lcd is at black state www..net
model c070fw01 v0 version : 0.9 9 page : 12 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. d. reliability test items(note 3): no. test items conditions remark 1 high temperature storage ta= 95 240hrs note 1 2 low temperature storage ta= -40 240hrs 3 high temperature operation tp= 85 240hrs note 2 4 low temperature operation ta= -30 240hrs 5 high temperature and high humidity tp= 60 , 90% rh 240hrs operation 6 heat shock -30 ~85 /200 cycles 1hrs/cycle non-operation 7 electrostatic discharge 200v,200pf(0 ), once for each terminal non-operation frequency range : 8~33.3hz stoke : 1.3mm sweep : 2.9g, 33.3 ~ 400hz cycle : 15 minutes 2 hours for each direction of x,z 8 vibration 4 hours for y direction jis d1601, a-10 condition a note 4 9 mechanical shock 100g, 6ms, x, y, z 3 times for each direction jis c7021, a-7 condition c 10 vibration (with carton) random vibration: 0.015g 2 /hz from 5~200hz C6db/octave from 200~500hz iec 68-34 11 drop (with carton) height: 60cm 1 corner, 3 edges, 6 surfaces jis z0202 note1: ta: ambient temperature. note2: tp: panel surface temperature note3: in the standard conditions, there is not displ ay function ng issue occurred. all the cosmetic specification is judged before the reliabili ty stress. note 4: cycle time for vibration is 15 minutes. www..net
model c070fw01 v0 version : 0.9 9 page : 13 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. e. packing form www..net
model c070fw01 v0 version : 0.9 9 page : 14 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. fig.1- outline dimension of tft-lcd module www..net
model c070fw01 v0 version : 0.9 9 page : 15 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. fig.- 2 outline dimension of tft lcd module www..net
model c070fw01 v0 version : 0.9 9 page : 16 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. 5 0 % 5 0 % 1 0 % 1 0 % 9 0 % 9 0 % s t h l ( r ) c p h 1 c p h 2 c p h 3 s t h t s u h t t h d h c 1 2 t t c 3 1 t c 2 3 c p h t t c w h t r f t fig.3 sampling clock timing www..net
model c070fw01 v0 version : 0.9 9 page : 17 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. i n p u t ( s t h l / s t h r ) o u t p u t ( s t h r / s t h l ) c p h 1 t d h fig. 4 horizontal display timing range www..net
model c070fw01 v0 version : 0.9 9 page : 18 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. o e h o e v v c o m 1 h t h v c d c c a c v v i d c b l a n k b l a c k v i a v i a c w h i t e b l a c k b l a n k w h i t e ( h s y ) s t h l ( r ) c k v r ( g b ) v fig.5-(a) horizontal timing www..net
model c070fw01 v0 version : 0.9 9 page : 19 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. fig.5-(b) detail horizontal timing www..net
model c070fw01 v0 version : 0.9 9 page : 20 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. s t v l ( r ) c k v 5 0 % 5 0 % t s u v h d v t t c k v fig.6 vertical shift clock timing www..net
model c070fw01 v0 version : 0.9 9 page : 21 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. v c o m ( e v e n f i e l d ) v c o m ( o d d f i e l d ) s t v l ( v s y ) d i s p l a y o n p a n e l f i r s t l i n e v r ( g b ) ( h s y ) t s v fig.6-(a) vertical timing (from up to down) www..net
model c070fw01 v0 version : 0.9 9 page : 22 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. fig.6-(b) vertical timing (from down to up) www..net
model c070fw01 v0 version : 0.9 9 page : 23 /23 all rights strictly reserved. any portion of this p aper shall not be reproduced, copied, or transformed to any other forms without permission f rom au optronics corp. t asu t ahd cph1 sthl vr 1st data f f f f i i i i g g g g u u u u r r r r e e e e - - - - 7 7 7 7 t t t t h h h h e e e e s s s s e e e e t t t t u u u u p p p p a a a a n n n n d d d d h h h h o o o o l l l l d d d d t t t t i i i i m m m m e e e e d d d d e e e e f f f f i i i i n n n n i i i i t t t t i i i i o o o o n n n n b b b b e e e e t t t t w w w w w w w w e e e e n n n n c c c c p p p p h h h h 1 1 1 1 a a a a n n n n d d d d a a a a n n n n a a a a l l l l o o o o g g g g s s s s i i i i g g g g n n n n a a a a l l l l v v v v r r r r www..net

▲Up To Search▲

Price & Availability of C070FW01V0

	To Download C070FW01V0 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .