RF1046 1333 mhz saw filter rf monolithics, inc. phone: +1(972)233-2903 european sales office 4347 sigma road fax: +1(972)387-8148 dallas, texas 75244 e-mail: info@rfm.com usa home page : www.rfm.com RF1046 7/22/1999 r electrical connections (see note 3) connection terminals port 1 hot 1 (near tab) port 2 hot 2 case ground 3 absolute maximum ratings rating value units maximum incident power in passband +10 dbm max. dc voltage between any 2 terminals 30 vdc storage temperature range -55 to +85 c max soldering profile 265 c for 10 s designed for front-end of rf detector simple external impedance matching hermetic to39-3 case unbalanced i nput and output see associated plots characteristic sym min typ max units notes nominal center frequency fc 1333.000 mhz il 6 8.0 db 1 bw 1 175 bw 3 850 khz passband insertion loss at fc 1 db passband 3 db passband group delay variation over fc 175 khz gdv 200 1000 ns p-p 1, 2 rejection < fc-140 mhz and > fc+140 mhz 55 63 db 1, 2, 3 operating temperature range t a -55 +85 c 1 impedance matching to 50 w unbalanced external l-c case style to39-3 9.3 mm diameter nominal footprint lid symbolization rfm RF1046 lot-code notes: 1. unless noted otherwise, all specifications apply over the operating temperature range with filter soldered to the specified demonstration board with impedance matching to 50 w and measured with 50 w network analyzer. 2. unless noted otherwise, all frequency specifications are referenced to the nominal center frequency, fc. 3. rejection is measured as attenuation below the minimum il point in the passband. rejection in final user application is dependent on pcb layout and external impe dance matching design. see application note no. 42 for details. all ?nc? or ?no connection? terminals should be grounded. 4. ?lrip? or ?l? after the part number indicates ?low rate initial production? and ?eng? or ?e? indicates ?engineering prototypes.? 5. the design, manufacturing process, and specifications of this filter are subject to change. 6. either port 1 or port 2 may be used for either input or output in the design. however, impedances and impedance matching may vary between port 1 and port 2, so that the filter must always be installed in one direction per the circuit design. 7. us and international patents may apply. 8. rfm, stylized rfm logo, and rf monolithics, inc. are registered trademarks of rf monolithics, inc. 9. ? copyright 1999, rf monolithics inc. 10. electrostatic sensitive device. observe precautions for handling.
RF1046 1333 mhz saw filter rf monolithics, inc. phone: +1(972)233-2903 european sales office 4347 sigma road fax: +1(972)387-8148 dallas, texas 75244 e-mail: info@rfm.com usa home page : www.rfm.com RF1046p.doc 8/11/1999 d 0 db -20 -40 -60 -80 -100 0 db -2 -4 -6 -8 -10 500 khz/div 35 mhz/div
rf monolithics, inc. phone: (972) 233-2903 fax: (972) 387-8148 e-mail: info@rfm.com rfm europe phone: 44 1963 251383 fax: 44 1963 251510 http://www.rfm.com ?1999 by rf monolithics, inc. the stylized rfm logo and rfm are registered trademarks of rf monolithics, inc. to39-3 dimensions mm inches min max min max a 9.30 0.366 b 3.18 0.125 c 2.50 3.50 0.098 0.138 d 0.46 nominal 0.018 nominal e 5.08 nominal 0.200 nominal f 2.54 nominal 0.100 nominal g 2.54 nominal 0.100 nominal h 1.02 0.040 j 1.40 0.055 3-lead, low-profile metal to39 9.3 mm dia nominal footprint to39-3 case b 45 j (2 places) d (3 places) h g e f c a 3 1 2
|
