ligitek electronics co.,ltd. property of ligitek only pb lead-free parts lhrf9ug3393/t-pf low current durl color led lamps data sheet doc. no : qw0905-lhrf9ug3393/t-pf rev. : a date : 23 - jun. - 2006
note : 1.all dimension are in millimeter tolerance is 0.25mm unless otherwise noted. 2.specifications are subject to change without notice. 50% 100%75% -60 -30 directivity radiation 100% 25% 0 25%75% 50% 60 30 0 1.5 max 0.5 typ 2.0min 2.54typ 1 2 3 package dimensions part no. lhrf9ug3393/t-pf 10.5 0.5 hrf 9ug 18.0min 1.anode green 2.common cathode 3.anode red 2.54typ 2.0min + 3 - 2 + 1 8.6 7.6 5.9 5.0 ligitek electronics co.,ltd. property of ligitek only page 1/6
tstg -40 ~ +100 storage temperature lhrf9ug3393/t-pf water clear note : 1.the forward voltage data did not including 0.1v testing tolerance. 2. the luminous intensity data did not including 15% testing tolerance. algainp green574202.2 1.890 5040 typical electrical & optical characteristics (ta=25 ) part no spectral halfwidth nm dominant wave length dnm color emitted algainpred material lens 63020 viewing angle 2 1/2 (deg) forward voltage @2ma(v) luminous intensity @2ma(mcd) max. min. typ. min. 1.52.0350550 40 electrostatic discharge( * ) operating temperature forward current reverse current @5v peak forward current duty 1/10@10khz power dissipation absolute maximum ratings at ta=25 i fp 9060 ma -40 ~ +85 t opr ir pd75 esd a 10 v mw 75 2000 ratings parameter symbol i f 30 hrf unit ma 30 9ug ligitek electronics co.,ltd. property of ligitek only page2/6 static electricity or power surge will damage the led. use of a conductive wrist band or anti-electrosatic glove is recommended when handing these led. all devices, equipment and machinery must be properly grounded. * part no. lhrf9ug3393/t-pf
1.0 f o r w a r d v o l t a g e @ 2 0 m a n o r m a l i z e @ 2 5 r e l a t i v e i n t e n s i t y @ 2 0 m a n o r m a l i z e @ 2 5 ambient temperature( ) ambient temperature( ) fig.5 relative intensity vs. wavelength -40 0.8 0.9 -20-02040 0.5 100 80 600 0 -20 -402040100 6080 ligitek electronics co.,ltd. property of ligitek only fig.2 relative intensity vs. forward current 100 forward current(ma) fig.4 relative intensity vs. temperature 3.0 f o r w a r d c u r r e n t ( m a ) forward voltage(v) fig.3 forward voltage vs. temperature 1.0 1.1 1.2 1.0 1.0 0.1 10 100 1.52.0 3.0 2.0 1.5 2.5 2.5 2.0 1.5 1.0 0.5 0 r e l a t i v e i n t e n s i t y n o r m a l i z e @ 2 0 m a 2.53.010 1.0 typical electro-optical characteristics curve fig.1 forward current vs. forward voltage hrf chip 1000 3.5 1000 650700 550600 wavelength (nm) 1.0 0.5 r e l a t i v e i n t e n s i t y @ 2 0 m a 0 page 3/6 part no. lhrf9ug3393/t-pf
fig.3 forward voltage vs. temperature ambient temperature( ) f o r w a r d v o l t a g e @ 2 0 m a n o r m a l i z @ 2 5 fig.4 relative intensity vs. temperature ambient temperature( ) r e l a t i v e i n t e n s i t y @ 2 0 m a n o r m a l i z e @ 2 5 typical electro-optical characteristics curve forward voltage(v) fig.1 forward current vs. forward voltage f o r w a r d c u r r e n t ( m a ) forward current(ma) fig.2 relative intensity vs. forward current r e l a t i v e i n t e n s i t y n o r m a l i z e @ 2 0 m a ligitek electronics co.,ltd. property of ligitek only 1.0 0.1 1.0 10 100 1000 1.0101001000 0 0.5 2.03.04.05.0 0.8 40 -20 -4080100 60 0 0.5 1.0 1.5 2.0 0.9 1.2 1.0 1.1 1.0 1.5 2.0 2.5 2.5 3.0 20 0 20 -400 -2080 4060100 3.0 9ug chip wavelength (nm) r e l a t i v e i n t e n s i t y @ 2 0 m a 0 500 0.5 1.0 550 600 650 fig.5 relative intensity vs. wavelength page 4/6 part no. lhrf9ug3393/t-pf
temp( c) 260 120 time(sec) 60 seconds max 2 /sec max 25 preheat 0 0 50 100 150 5 /sec max 260 c3sec max soldering condition(pb-free) 1.iron: soldering iron:30w max temperature 350 c max soldering time:3 seconds max(one time) distance:2mm min(from solder joint to body) 2.wave soldering profile dip soldering preheat: 120 c max preheat time: 60seconds max ramp-up 2 c/sec(max) ramp-down:-5 c/sec(max) solder bath:260 c max dipping time:3 seconds max distance:2mm min(from solder joint to body) ligitek electronics co.,ltd. property of ligitek only page 5/6 part no. lhrf9ug3393/t-pf
this test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. solderability test 1.t.sol=230 5 2.dwell time=5 1sec mil-std-202: 208d mil-std-750: 2026 mil-std-883: 2003 jis c 7021: a-2 this test intended to see soldering well performed or not. low temperature storage test 1.ta=-40 5 2.t=1000 hrs (-24hrs, +72hrs) thermal shock test solder resistance test 1.t.sol=260 5 2.dwell time= 10 1sec. 1.ta=105 5 &-40 5 (10min) (10min) 2.total 10 cycles high temperature high humidity test 1.ta=65 5 2.rh=90%~95% 3.t=240hrs 2hrs high temperature storage test 1.ta=105 5 2.t=1000 hrs (-24hrs, +72hrs) test item operating life test 1.under room temperature 2.if=20ma 3.t=1000 hrs (-24hrs, +72hrs) test condition reliability test: jis c 7021: b-12 the purpose of this is the resistance of the device which is laid under condition of low temperature for hours. mil-std-202: 210a mil-std-750: 2031 jis c 7021: a-1 mil-std-202: 107d mil-std-750: 1051 mil-std-883: 1011 the purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. mil-std-202:103b jis c 7021: b-11 the purpose of this test is the resistance of the device under tropical for hours. mil-std-883:1008 jis c 7021: b-10 the purpose of this is the resistance of the device which is laid under condition of high temperature for hours. mil-std-750: 1026 mil-std-883: 1005 jis c 7021: b-1 reference standard this test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. description page 6/6 ligitek electronics co.,ltd. property of ligitek only part no. lhrf9ug3393/t-pf
|
