PC910L0NSZ PC910L0NSZ absolute maximum ratings outline dimensions (unit : mm) 1. high speed interfaces for computer peripherals 2. programmable controllers 3. inverters features applications ultra-high speed response ? opic photocoupler 1. ultra-high speed response (t phl , t plh :typ. 50ns at r l = 350 ? ) 2. isolation voltage between input and output (v iso (rms) :5.0kv) 3. low input current drive (i fhl :max. 5ma) 4. instantaneous common mode rejection voltage (cm h :typ. 20kv/ s) 5. ttl and lsttl compatible output 6. recognized by ul, file no. e64380 (model no. pc910l) primary side mark : 0 to 13 ? 2.54 0.25 6.5 0.5 0.85 0.2 1.2 0.3 9.66 0.3 3.5 0.5 7.62 0.3 3.05 0.5 3.4 0.5 0.5 0.1 0.5 typ. 0.26 0.1 8 7 pc910l 6 5 1 2 3 4 1 1 2 3 4 8 7 6 5 2 3 4 5 6 7 8 ? ?pic?optical ic) is a trademark of the sharp corporation. an opic consists of a light-detecting element and signal- processing circuit integrated onto a single chip. internal connection diagram nc anode cathode nc nc gnd v o (open collector) v cc v cc gnd * vde (vde0884) approved type is also available us an option notice in the absence of confirmation by device specification sheets, sharp takes no responsibility for any defects that may occ ur in equipment using any sharp devices shown in catalogs, data books, etc. contact sharp in order to obtain the latest device specification sheets before usin g any sharp device. internet internet address for electronic components group http://sharp-world.com/ecg/ input i f 20 ma reverse voltage v r 5v power dissipation p 40 mw output v cc 7v v e 5.5 v high level output voltage v oh 7v low level output current i ol 50 ma collector power dissipation p c 85 mw operating temperature storage temperature v iso (rms) t opr ? 40 to + 85 ? c t stg ? 55 to + 125 ? c t sol 270 ? c *1 forward current *2 supply voltage *3 enable voltage *4 isolation voltage soldering temperature 5.0 kv *1 t a = t opr *2 shall not exceed 500mv from supply voltage (v cc ) *3 40 to 60%rh, ac for 1minute *4 for 10s parameter symbol rating unit (t a = 25 c)
PC910L0NSZ parameter symbol unit input forward voltage v f v reverse current i r a terminal capacitance c t t a = 25 ? c, v = 0, f = 1khz v cc = v o = 5.5v, v e = 2.0v, i f = 250 a pf ma ma output i oh v ol ma ma v high level enable current i el low level enable current i cch a i eh transfer charac- teristics isolation resistance r iso ? t plh t r t f ? t w ns t phl ns t a = 25 ? c, i f = 10ma t a = 25 ? c, v r = 5v v cc = 5.5v, i f = 0,v e = 2v min. ? ? ? 5 10 10 25 25 ? ? max. 10 150 ? 1.6 ? ? 1.6 13 ? 1.9 75 75 conditions "high low" threshold input current cm h cm l v cc = v o = 5.5v, v e = 2.0v, i f = 5ma, i ol = 13ma v cc = 5.5v, v e = 2.0v v cc = 5.5v, v e = 0.5v v cc = 5.5v, i f = 0,v e = 0.5v high level supply current i ccl i fhl low level supply current v cc = 5.5v, i f = 10ma,v e = 2v v cc = 5.5v, i f = 10ma,v e = 0.5v t a = 25 ? c, dc = 500v, 40 to 60%rh v cc = 5v,v e = 2.0v, v o = 0.8v, r l = 350 ? *6 it shall connect a by-pass capacitor of 0.01 f or more between v cc (pin 8 ) and gnd (pin 5 ) near the device, when it measures the transfer characteristics and the output side characteristics *7 distortion of pulse width ? t w = | t phl ? t plh | *7 typ. ? 60 ? 100 0.02 ? 0.6 0.4 ma ?? 5 5.5 ma ? 10 ? 0.5 ? 0.7 5 10 11 floating capacitance c f t a = 25 ? c, v = 0, f = 1mhz t a = 25 ? c, v cc = 5v, r l = 350 ? , c l = 15pf, i f = 7.5ma t a = 25 ? c, v cc = 5v, r l = 350 ? , c l = 15pf, i f = 7.5ma, v eh = 3v, v el = 0.5v t a = 25 ? c, v cc = 5v, v cm = 1kv (p-p) , r l = 350 ? , i f = 0, v o (min) = 2v t a = 25 ? c, v cc = 5v, v cm = 1kv (p-p) , r l = 350 ? , i f = 5ma, v o (max) = 0.8v 1.6 ? ? ma 5 2.5 ? 7 50 ns ?? 10 ns ?? 20 ns ? 35 ? ns ?? 15 ns ?? 10 kv/ s 10 ? 20 pf ? 5 0.6 48 kv/ s ? 10 ? ? 20 (unspecified t a =? 40 to + 85 ? c, all typical values at t a = 25 ? c, v cc = 5v) high level output voltage low level output voltage "high low" propagation time "high low" enable propagation delay time "low high" enable propagation delay time instantaneous common mode rejection voltage "output : high level" instantaneous common mode rejection voltage "output : low level" "low high" propagation time rise time fall time distortion of pulse width response time cmr fig. 1 fig.2 fig.3 fig.3 t ehl t elh electro-optical characteristics recommended operating conditions low level input current i fl 250 a high level input current i fh 15 ma high level enable voltage v eh v cc v low level enable voltage v el 0.8 v supply voltage v cc 5.5 v fanout (ttl load) n 8 ? operating temperature t opr 0 8 2.0 0 4.5 ? ? 40 85 ? c 1. when the enable input is in high level state, extemal pull-up resistor is unnecessary parameter symbol min. max. unit
PC910L0NSZ truth table circuit block diagram anode cathode v cc v e (enable) v o gnd fig.1 test circuit for t phl , t plh , t r and t f fig.2 test circuit for t ehl and t elh fig.3 test circuit for cm h and cm l l:logic (0) h:logic (1) input enable output hhl lhh hlh llh 1 2 3 45 6 7 8 350 ? 5v 47 ? pulse input 0.1 f i f c l v o *c l includes the probe and wiring capacitance. 90 % 10 % 7.5ma 3.75ma 0ma 5v 1.5v i f v o t phl t plh v ol t r t f 0.1 f 5v 350 ? 8 7 6 5 4 3 2 1 pulse input v e i f = 7.5ma v o c l 1.5v 5v 0.5v 1.5v 3v v e v o t ehl t elh v ol *c l includes the probe and wiring capacitance. 0.1 f 5v 350 ? 8 7 6 5 4 3 2 1 a b gl sw i f c l v cm 1kv 0v 5v v cm v o v o (i f = 0ma) (i f = 5ma) v o (min.) v o (max.) v ol when the switch for infrared light emitting diode sets to a when the switch for infrared light emitting diode sets to b *c l includes the probe and wiring capacitance.
PC910L0NSZ fig.6 forward current vs. forward voltage fig.8 low level output voltage vs. ambient temperature fig.9 threshold input current vs. ambient temperature fig.5 collector power dissipation vs. ambient temperature fig.7 high level output current vs. ambient temperature collector power dissipation p c (mw) ambient temperature t a ( c) 0 20 40 60 80 85 100 ? 40 0 25 50 100 125 70 85 ? 25 fig.4 forward current vs. ambient temperature forward current i f (ma) ambient temperature t a ( c) 0 5 10 15 20 25 ? 40 0 25 50 100 125 70 85 ? 25 ambient temperature t a ( ? c) high level output current i oh ( a) ? 50 ? 25 0 25 50 100 75 0.01 0.1 1.0 10.0 100.0 0.001 i f = 250 a v cc = 5.5v v o = 5.5v v e = 2.0v threshold input current i fhl (ma) 4.0 5.0 6.0 0.0 v cc = 5v v o = 0.8v v e = 2.0v r l = 350 ? 3.0 2.0 ambient temperature t a ( ? c) ? 50 ? 25 0 25 50 100 75 1.0 forward voltage v f (v) forward current i f (ma) 1.00 1.20 1.40 1.60 1.80 2.00 1 10 100 0.1 t a = 50 ? c t a = 0 ? c t a =? 20 ? c t a =? 40 ? c t a = 85 ? c t a = 25 ? c low level output voltage v ol (v) 0.4 0.6 0.8 0.0 i f = 5.0ma v cc = 5.5v v e = 2.0v 0.2 i o = 16.0ma i o = 12.8ma i o = 9.6ma i o = 6.4ma ambient temperature t a ( ? c) ? 50 ? 25 0 25 50 100 75
PC910L0NSZ fig.11 propagation delay time vs. forward current fig.12 propagation delay time vs. ambient temperature propagation delay time t phl , t plh (ns) 0 100 20 40 60 80 5 101520 forward current i f (ma) t a = 25 ? c v cc = 5.0v r l = 350 ? t plh t phl propagation delay time t phl , t plh (ns) 0.0 100.0 20.0 40.0 60.0 80.0 ? 50 0 ? 25 75 50 25 100 ambient temperature t a ( ? c) i f = 7.5ma v cc = 5.0v r l = 350 ? t plh t phl fig.10 output voltage vs. forward current 0 1 2 6 0 3 12 6 4 3 5 4 5 output voltage v o (v) forward current i f (ma) v cc = 5.0v v o = 0.8v v e = 2.0v t a = 25 ? c r l = 350 ? r l = 1k ? r l = 4k ?
notice the circuit application examples in this publication are provided to explain representative applications of sharp devices and are not intended to guarantee any circuit design or license any intellectual property rights. sharp takes no responsibility for any problems related to any intellectual property right of a third party resulting from the use of sharp's devices. contact sharp in order to obtain the latest device specification sheets before using any sharp device. sharp reserves the right to make changes in the specifications, characteristics, data, materials, structure, and other contents described herein at any time without notice in order to improve design or reliability. manufacturing locations are also subject to change without notice. observe the following points when using any devices in this publication. sharp takes no responsibility for damage caused by improper use of the devices which does not meet the conditions and absolute maximum ratings to be used specified in the relevant specification sheet nor meet the following conditions: (i) the devices in this publication are designed for use in general electronic equipment designs such as: - - - personal computers - - - office automation equipment - - - telecommunication equipment [terminal] - - - test and measurement equipment - - - industrial control - - - audio visual equipment - - - consumer electronics (ii) measures such as fail-safe function and redundant design should be taken to ensure reliability and safety when sharp devices are used for or in connection with equipment that requires higher reliability such as: - - - transportation control and safety equipment (i.e., aircraft, trains, automobiles, etc.) - - - traffic signals - - - gas leakage sensor breakers - - - alarm equipment - - - various safety devices, etc. (iii)sharp devices shall not be used for or in connection with equipment that requires an extremely high level of reliability and safety such as: - - - space applications - - - telecommunication equipment [trunk lines] - - - nuclear power control equipment - - - medical and other life support equipment (e.g., scuba). if the sharp devices listed in this publication fall within the scope of strategic products described in the foreign exchange and foreign trade law of japan, it is necessary to obtain approval to export such sharp devices. this publication is the proprietary product of sharp and is copyrighted, with all rights reserved. under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without the express written permission of sharp. express written permission is also required before any use of this publication may be made by a third party. contact and consult with a sharp representative if there are any questions about the contents of this publication.
|
