 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| UNISONIC TECHNOLOGIES CO., LTD UIC811 Preliminary LINEAR INTEGRATED CIRCUIT MICROPROCESSOR RESET CIRCUITS DESCRIPTION The UTC UIC811 series are resetting circuits which can monitor power supplies especially in microprocessor based systems. In normal operation, the UTC UIC811 series can assert a reset under any of the following situation: the power supply drops below a designated reset threshold level (which is available for 3V or 3.3V system) or MR is forced low. There is an internal active low RESET output which has already been guaranteed to remain asserted for at 140ms least while VCC rises above the designed threshold level. FEATURES * Voltage monitor for 3V or 3.3V power supplies * Valid RESET remains with VCC as low as 1V * Typical supply current: 5A * Fixed140ms minimum reset pulse width * With Manual reset input * Halogen Free ORDERING INFORMATION Ordering Number Package UIC811G-x-AD4-R SOT-143 Note: x: Output Voltage, refer to Marking Information. Packing Tape Reel www..com www.unisonic.com.tw Copyright (c) 2009 Unisonic Technologies Co., Ltd 1 of 7 QW-R502-317.b UIC811 PACKAGE Preliminary LINEAR INTEGRATED CIRCUIT MARKING INFORMATION VOLTAGE CODE A : 2.63V B : 2.93V C : 3.08V D: 4.00V E: 4.38V MARKING 4 UXG 1 2 3 SOT-143 Voltage Code PIN CONFIGURATION PIN DESCRIPTION PIN NO. 1 2 3 4 PIN NAME GND RESET DESCRIPTION Ground This pin will fall low after the VCC's falling below the reset threshold voltage and it also can remain asserted for at least 140ms min after VCC's rising upon the reset threshold. Input of manual reset. A reset can be forced by a logic low on MR . As the MR is held MR VCC low, the reset will remain asserted, and until the MR rise high, the reset will remain140ms min at least. When it is float that means it is unused. Input of power supply. www..com UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 2 of 7 QW-R502-317.b UIC811 BLOCK DIAGRAM Preliminary LINEAR INTEGRATED CIRCUIT VCC 4 RESET GENERATOR Reset Threshold 2 RESET MR 3 1 GND FUNCTIONAL DIAGRAM VCC VTH MR tRST RESET tRST Reset Timing Diagram www..com UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 3 of 7 QW-R502-317.b UIC811 PARAMETER Input Voltage Input Current (VCC, MR ) Output Current ( RESET ) Rate of Rise Power Dissipation (Ta =+70C) Operating Temperature Preliminary LINEAR INTEGRATED CIRCUIT ABSOLUTE MAXIMUM RATING SYMBOL VCC IIN IOUT VCC(RR) PD RATINGS -0.3~+6.0 20 20 100 320 UNIT V mA mA V/s mW -40~+85 C TOPR C TSTG -65~+150 Storage Temperature Note: 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged. Absolute maximum ratings are stress ratings only and functional device operation is not implied. 2. The device is not guaranteed to function outside its operating rating. ELECTRICAL CHARACTERISTICS UIC811-A (2.63V) (VCC =3V, Ta = 25C, unless otherwise specified) PARAMETER Operating Voltage Range Supply Current Reset Voltage Threshold Reset Timeout Period Reset Output Voltage MR Input Threshold MR Minimum Pulse Width MR to Reset Delay MR Pull-Up Resistance MR Glitch Immunity SYMBOL TEST CONDITIONS VCC Ta =-40~+85C ICC VCC=3.0V, no load VTH tRST VOH ISOURCE =500A VCC = VTH min, ISINK =1.2mA VOL VCC>1V, ISINK =50A,Ta =-40~+85C VIH VIL TYP MAX UNIT 5.5 V 5 10 A 2.55 2.63 2.70 V 140 240 560 ms 2.4 V 0.3 V 0.3 V 2.1 V 0.75 V 10 S 0.5 10 20 100 30 S k ns MIN 1 UIC811-B (2.93V) (VCC =3.3V, Ta= 25C, unless otherwise specified) PARAMETER Operating Voltage Range Supply Current Reset Voltage Threshold Reset Timeout Period Reset Output Voltage MR Input Threshold MR Minimum Pulse Width MR to Reset Delay MR Pull-Up Resistance MR Glitch Immunity SYMBOL TEST CONDITIONS VCC Ta =-40~+85C ICC VCC=3.3V, no load VTH tRST VOH ISOURCE =500A VCC = VTH min, ISINK =1.2mA VOL VCC>1V, ISINK =50A,Ta =-40~+85C VIH VIL TYP MAX UNIT 5.5 V 5 10 A 2.85 2.93 3.00 V 140 240 560 ms 2.64 V 0.3 V 0.3 V 2.31 V 0.825 V 10 S 0.5 10 20 100 30 S k ns MIN 1 www..com UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 4 of 7 QW-R502-317.b UIC811 PARAMETER Operating Voltage Range Supply Current Reset Voltage Threshold Reset Timeout Period Reset Output Voltage MR Input Threshold MR Minimum Pulse Width MR to Reset Delay MR Pull-Up Resistance MR Glitch Immunity Preliminary LINEAR INTEGRATED CIRCUIT ELECTRICAL CHARACTERISTICS(Cont.) UIC811-C (3.08V) (VCC =3.3V, Ta= 25C, unless otherwise specified) SYMBOL TEST CONDITIONS VCC Ta =-40~+85C ICC VCC=3.3V, no load VTH tRST VOH ISOURCE =500A VCC = VTH min, ISINK =1.2mA VOL VCC>1V, ISINK =50A,Ta =-40~+85C VIH VIL TYP MAX UNIT 5.5 V 5 10 A 3.00 3.08 3.15 V 140 240 560 ms 2.64 V 0.3 V 0.3 V 2.31 V 0.825 V 10 S 0.5 10 20 100 SYMBOL TEST CONDITIONS VCC Ta =-40~+85C ICC VCC=5.0V, no load VTH tRST VOH ISOURCE =800A VCC = VTH min, ISINK =3.2mA VOL VCC>1V, ISINK =50A,Ta =-40~+85C VIH VIL MIN 1 30 S k ns MIN 1 UIC811-D (4.00V) (VCC =5V, Ta= 25C, unless otherwise specified) PARAMETER Operating Voltage Range Supply Current Reset Voltage Threshold Reset Timeout Period Reset Output Voltage MR Input Threshold MR Minimum Pulse Width MR to Reset Delay MR Pull-Up Resistance MR Glitch Immunity TYP MAX UNIT 5.5 V 5 15 A 3.89 4.00 4.10 V 140 240 560 ms 3.5 V 0.4 V 0.3 V 2.3 V 0.8 V 10 S 0.5 10 20 100 30 S k ns UIC811-E (4.38V) (VCC =5V, Ta= 25C, unless otherwise specified) PARAMETER Operating Voltage Range Supply Current Reset Voltage Threshold Reset Timeout Period Reset Output Voltage MR Input Threshold MR Minimum Pulse Width MR to Reset Delay MR Pull-Up Resistance www..com MR Glitch Immunity SYMBOL TEST CONDITIONS VCC Ta =-40~+85C ICC VCC=5.0V, no load VTH tRST VOH ISOURCE =800A VCC = VTH min, ISINK =3.2mA VOL VCC>1V, ISINK =50A,Ta =-40~+85C VIH VIL TYP MAX UNIT 5.5 V 5 15 A 4.25 4.38 4.50 V 140 240 560 ms 3.5 V 0.4 V 0.3 V 2.3 V 0.8 V 10 S 0.5 10 20 100 30 S k ns MIN 1 UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 5 of 7 QW-R502-317.b UIC811 Preliminary LINEAR INTEGRATED CIRCUIT TYPICAL APPLICATION CIRCUIT VCC VCC VCC UTC UIC811 RESET MR RESET P APPLICATION INFORMATION Microprocessor Reset As soon as VCC falls below the reset threshold voltage, the RESET pin is asserted. But the RESET pin can keep asserted for a period of 140ms after VCC rose above the reset threshold voltage. After a power failure the reset operation can keep the processor being reset and powers up properly. VCC Transients The UTC UIC811 series won't cause a reset typically as this situation: a negative-going transient 125mV below the reset threshold with a duration of 20s or less. Interfacing to Bidirectional Reset Pins Connecting a 4.7k resistor in series with the UTC UIC811 series output and the P reset pin can make the UTC UIC811 series interface with Ps with bidirectional reset pins. RESET Valid at Low Voltage As the figure below, adding a resistor which is recommended 100k can ensure the RESET output remains low with VCC down to 0V. The size of the resistor should be not too large which will load the output excessively and not too small which can pull-down any stray leakage currents. www..com UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 6 of 7 QW-R502-317.b UIC811 Preliminary LINEAR INTEGRATED CIRCUIT UTC assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or www..com other parameters) listed in products specifications of any and all UTC products described or contained herein. UTC products are not designed for use in life support appliances, devices or systems where malfunction of these products can be reasonably expected to result in personal injury. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner. The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed without notice. UNISONIC TECHNOLOGIES CO., LTD www.unisonic.com.tw 7 of 7 QW-R502-317.b |
Price & Availability of UIC811
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |