View HLMP-0301-D0002_365755.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

2.5 mm x 7.6 mm Rectangular LED Lamps Technical Data
HLMP-R100 HLMP-0301 HLMP-0401 HLMP-0504
Features
* Rectangular Light Emitting Surface * Flat High Sterance Emitting Surface * Stackable on 2.54 mm (0.100 inch) Centers * Ideal as Flush Mounted Panel Indicators * Ideal for Backlighting Legends * Long Life: Solid State Reliability * Choice of 4 Bright Colors DH AS AlGaAs Red High Efficiency Red Yellow High Performance Green * IC Compatible/Low Current Requirements
The HLMP-R100 uses a double heterojunction (DH) absorbing substrate (AS) aluminum gallium arsenide (AlGaAs) red LED chip in a light red epoxy package. This combination produces outstanding light output over a wide range of drive currents. The HLMP-0301 has a high efficiency red GaAsP on GaP LED chip in a light red epoxy package. The HLMP-0401 provides a yellow GaAsP on GaP LED chip in a yellow epoxy package.
The HLMP-0504 provides a green GaP LED chip in a green epoxy package.
Package Dimensions
Description
The HLMP-R100, -0301, -0401, -0504 are solid state lamps encapsulated in a radial lead rectangular epoxy package. They utilize a tinted, diffused epoxy to provide high on-off contrast and a flat high intensity emitting surface. Borderless package design allows creation of uninterrupted light emitting areas.
2
Selection Guide
Luminous Intensity Iv (mcd) @ 20 mA Min. Typ. 2.1 - 5.4 17.2 2.1 - 1.3 - 2.1 6.8 1.3 4.2 3.6 - 1.4 - 3.6 - 2.2 7.2 3.6 11.4 2.6 - 1.6 - 4.2 13.4 2.6 8.4 2.6 -
Color DH AlGaAs Red Red
Yellow
Green
Part Number HLMP-R100 HLMP-R100-FG0xx HLMP-0301 HLMP-0301-C00xx HLMP-0301-DECxx HLMP-0301-CD0xx HLMP-0401 HLMP-0401-B00xx HLMP-0401-D00xx HLMP-0401-CD0xx HLMP-0401-DEBxx HLMP-0504 HLMP-0504-B00xx HLMP-0504-DECxx HLMP-0504-CD0xx HLMP-0504-C00xx
Part Numbering System
HLMP - x x xx - x x x xx Mechanical Options 00: Bulk 01: Tape & Reel, Crimped Leads 02: Tape & Reel, Straight Leads DD: Ammo Pack, Straight Leads Color Bin Options 0: Full Color Bin Distribution B: Color Bins 2 & 3 only C: Color Bins 3 & 4 only Maximum Iv Bin Options 0: Open (No Maximum Limit) Others: Please refer to the Iv Bin Table Minimum Iv Bin Options Please refer to the Iv Bin Table Color Options 1. As AlGaAs Red 3. High Efficiency Red 4. Yellow 5. Green Package Options R,0: Rectangular 2.5 mm x 7.6 mm
3
Absolute Maximum Ratings at TA = 25C
Parameter Peak Forward Current Average Forward Current[1] DC Current[2] Power Dissipation Reverse Voltage (IR = 100 A) Transient Forward Current[3] (10 s Pulse) Operating Temperature Range Storage Temperature Range Lead Soldering Temperature (1.6 mm [0.063 in.] from body) HLMPR100 300 20 30 87 5 500 -20 to +100 -55 to +100 260C for 5 seconds HLMP0301 90 25 30 135 5 500 -55 to +100 HLMP0401 60 20 20 85 5 500 -55 to +100 HLMP0504 90 25 30 135 5 500 -20 to +100 -55 to +100 Units mA mA mA mW V mA C
Notes: 1. See Figure 5 to establish pulsed operating conditions. 2. For AlGaAs Red, Red, and Green Series derate linearly from 50C at 0.5 mA/C. For Yellow Series derate linearly from 50C at 0.2 mA/C. 3. The transient peak current is the maximum non-recurring peak current that can be applied to the device without damaging the LED die and wirebond. It is not recommended that the device be operated at peak current beyond the peak forward current listed in the Absolute Maximum Ratings.
4
Electrical/Optical Characteristics at TA = 25C
HLMP-R100 Sym. 21/2 Description Included Angle Between Half Luminous Intensity Points Peak Wavelength Dominant Wavelength Spectral Line Halfwidth Speed of Response Capacitance Thermal Resistance Forward Voltage Reverse Breakdown Voltage Luminous Efficacy 5.0 HLMP-0301 HLMP-0401 HLMP-0504 Test Conditions Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Units
100
100
100
100
Deg.
Note 1. Fig. 6
P d 1/2 s C RJ-PIN VF VR
645 637 20 30 30 260 1.8 2.2 5.0
635 626 40 90 16 260 1.9 2.6 5.0
583 585 36 90 18 260 2.1 2.6 5.0
565 569 28 500 18 260 2.2 3.0
nm nm nm ns pF C/W V V
Measurement at Peak Note 2
VF = 0; f = 1 MHz Junction to Cathode Lead IF = 20 mA Figure 2. IR = 100 A
v
80
145
500
595
lm/W
Note 3
Notes: 1. 1/2 is the off-axis angle at which the luminous intensity is half the axial luminous intensity. 2. The dominant wavelength, d, is derived from the CIE chromaticity diagram and represents the single wavelength which defines the color of the device. 3. Radiant intensity, Ie, in watts/steradian, may be found from the equation Ie = Iv/v, where Iv is the luminous intensity in candelas and v is the luminous efficacy in lumens/watt.
Figure 1. Relative Intensity vs. Wavelength.
5
Figure 2. Forward Current vs. Forward Voltage. VF (300 mA) for AlGaAs Red = 2.6 Volts Typical.
Figure 3. Relative Luminous Intensity vs. Forward Current.
Figure 4. Relative Efficiency (Luminous Intensity per Unit Current) vs. Peak Current. v (300 mA) for AlGaAs Red = 0.7.
Figure 5. Maximum Tolerable Peak Current vs. Peak Duration (IPEAK MAX Determined from Temperature Derated I DC MAX).
Figure 6. Relative Luminous Intensity vs. Angular Displacement.
6
Intensity Bin Limits
Color Bin C D E F G H I J K L M N O P Q R S T U V W X Y Z Intensity Range (mcd) Min. Max. 0.5 2.4 2.4 3.8 3.8 6.1 6.1 9.7 9.7 15.5 15.5 24.8 24.8 39.6 39.6 63.4 63.4 101.5 101.5 162.4 162.4 234.6 234.6 340.0 340.0 540.0 540.0 850.0 850.0 1200.0 1200.0 1700.0 1700.0 2400.0 2400.0 3400.0 3400.0 4900.0 4900.0 7100.0 7100.0 10200.0 10200.0 14800.0 14800.0 21400.0 21400.0 30900.0
Red
7
Intensity Bin Limits, continued
Color Bin B C D E F G H I J K L M N O P Q R S T U V W B C D E F G H I J K L M N O P Q R S T U V W Intensity Range (mcd) Min. Max. 1.6 2.5 2.5 4.0 4.0 6.5 6.5 10.3 10.3 16.6 16.6 26.5 26.5 42.3 42.3 67.7 67.7 108.2 108.2 173.2 173.2 250.0 250.0 360.0 360.0 510.0 510.0 800.0 800.0 1250.0 1250.0 1800.0 1800.0 2900.0 2900.0 4700.0 4700.0 7200.0 7200.0 11700.0 11700.0 18000.0 18000.0 27000.0 1.8 2.9 2.9 4.7 4.7 7.6 7.6 12.0 12.0 19.1 19.1 30.7 30.7 49.1 49.1 78.5 78.5 125.7 125.7 201.1 201.1 289.0 289.0 417.0 417.0 680.0 680.0 1100.0 1100.0 1800.0 1800.0 2700.0 2700.0 4300.0 4300.0 6800.0 6800.0 10800.0 10800.0 16000.0 16000.0 25000.0 25000.0 40000.0
Yellow
Green
Maximum tolerance for each bin limit is 18%.
Color Categories
Color Category # 6 5 4 3 2 1 3 2 4 5 Lambda (nm) Min. Max. 561.5 564.5 564.5 567.5 567.5 570.5 570.5 573.5 573.5 576.5 582.0 584.5 584.5 587.0 587.0 589.5 589.5 592.0 592.0 593.0
Green
Yellow
Tolerance for each bin limit is 0.5 nm.
Mechanical Option Matrix
Mechanical Option Code 00 01 02 DD Definition Bulk Packaging, minimum increment 500 pcs/bag Tape & Reel, crimped leads, minimum increment 1300 pcs/bag Tape & Reel, straight leads, minimum increment 1300 pcs/bag Ammo Pack, straight leads with minimum increment 2K/pack
Note: All categories are established for classification of products. Products may not be available in all categories. Please contact your local Agilent representative for further clarification/information.
www.semiconductor.agilent.com Data subject to change. Copyright (c) 2001 Agilent Technologies, Inc. August 15, 2001 Obsoletes 5968-4160E (3/99) 5988-2147EN

▲Up To Search▲

Price & Availability of HLMP-0301-D0002

	To Download HLMP-0301-D0002 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .