View UG-9616GLBBG01_156704.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

www..com
Product Specification
(Preliminary) Part Name: OEL Display Module Part ID: UG-9616GLBBG01 Doc No.: SAS1-M003-B
Customer:
Approved by
From: Univision Technology Inc.
Approved by
Univision Technology Inc.
8, Kebei RD 2, Science Park, Chu-Nan, Taiwan 350, R.O.C.
Notes: 1. Please contact Univision Technology Inc. before assigning your product based on this module specification 2. The information contained herein is presented merely to indicate the characteristics and performance of our products. No responsibility is assumed by Univision Technology Inc. for any intellectual property claims or other problems that may result from application based on the module described herein.
Univision Technology Inc.
Revised History
Part Number UG-9616GLBBG01 Revision A New Page 4 Page 6 Page 9 Revision Content Section 1.6 Section 3.2 Section 4.4
Doc. No: SAS1-M003-B e t 4 U . c o m www.DataShe
Revised on December 5, 2007
Modify Application Circuit
UG-9616GLBBG01
B
Update DC Characteristics Update Actual Application Example
February 20, 2008
i
Univision Technology Inc.
Doc. No: SAS1-M003-B www..com
Notice:
No part of this material may be reproduces or duplicated in any form or by any means without the written permission of Univision Technology Inc. Univision Technology Inc. reserves the right to make changes to this material without notice. Univision Technology Inc. does not assume any liability of any kind arising out of any inaccuracies contained in this material or due to its application or use in any product or circuit and, further, there is no representation that this material is applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that anything made in accordance with this material will be free from any patent or copyright infringement of a third party. This material or portions thereof may contain technology or the subject relating to strategic products under the control of Foreign Exchange and Foreign Trade Law of Taiwan and may require an export license from the Ministry of International Trade and Industry or other approval from another government agency. (c) Univision Technology Inc. 2008, All rights reserved. All other product names mentioned herein are trademarks and/or registered trademarks of their respective companies.
ii
Univision Technology Inc. Contents
Doc. No: SAS1-M003-B www..com
Revision History ................................................................................................... i Notice ................................................................................................................... ii Contents .............................................................................................................. iii 1. Basic Specifications .................................................................................. 1~4
1.1 1.2 1.3 1.4 1.5 1.6 Display Specifications .................................................................................................1 Mechanical Specifications ...........................................................................................1 Active Area & Pixel Construction ...............................................................................1 Mechanical Drawing....................................................................................................2 Pin Definition...............................................................................................................3 Block Diagram .............................................................................................................4
2. Absolute Maximum Ratings .......................................................................... 5 3. Optics & Electrical Characteristics ........................................................... 6~7
3.1 Optics Characteristics ..................................................................................................6 3.2 DC Characteristics .......................................................................................................6 3.3 AC Characteristics .......................................................................................................7
4. Functional Specification ........................................................................... 8~9
4.1 Commands ...................................................................................................................8 4.2 Power down and Power up Sequence ..........................................................................8 4.2.1 Power up Sequence ............................................................................................8 4.2.2 Power down Sequence .......................................................................................8 4.3 Reset Circuit.................................................................................................................8 4.4 Actual Application Example ........................................................................................9
5. Reliability ...................................................................................................... 10
5.1 Contents of Reliability Tests......................................................................................10 5.2 Lifetime......................................................................................................................10 5.3 Failure Check Standard..............................................................................................10
6. Outgoing Quality Control Specifications .............................................. 11~15
6.1 Environment Required ...............................................................................................11 6.2 Sampling Plan ............................................................................................................11 6.3 Criteria & Acceptable Quality Level .........................................................................11 6.3.1 Cosmetic Check (Display Off) in Non-Active Area ........................................11 6.3.2 Cosmetic Check (Display Off) in Active Area.................................................14 6.3.3 Pattern Check (Display On) in Active Area.....................................................15
7. Package Specifications ................................................................................ 16 8. Precautions When Using These OEL Display Modules ....................... 17~19
8.1 8.2 8.3 8.4 Handling Precautions .................................................................................................17 Storage Precautions....................................................................................................18 Designing Precautions ...............................................................................................18 Precautions when disposing of the OEL display modules.........................................19
iii
Univision Technology Inc.
Doc. No: SAS1-M003-B www..com
8.5 Other Precautions.......................................................................................................19
iv
Univision Technology Inc.
1. Basic Specifications
1.1 Display Specifications 1) 2) 3) Display Mode: Display Color: Drive Duty: Passive Matrix Monochrome (Light Blue) 1/16 Duty
Doc. No: SAS1-M003-B www..com
1.2 Mechanical Specifications 1) 2) 3) 4) 5) 6) 7) Outline Drawing: Number of Pixels: Panel Size: Active Area: Pixel Pitch: Pixel Size: Weight: According to the annexed outline drawing 96 x 16 29.10 x 9.20 x 1.60 (mm) 21.104 x 3.504 (mm) 0.22 x 0.22 (mm) 0.204 x 0.204 (mm) 0.89 (g)
1.3 Active Area & Pixel Construction
P0.22x96-0.016=21.104 (A/A) Display Pattern
P0.22x16-0.016=3.504 (A/A)
Segment 127
( Column 1 )
Segment 32
( Column 96 )
Common 0
( Row 16 )
Common 15
( Row 1 )
0.22 0.204
0.22 0.204
Display Pattern Scale (10:1)
1
Item A B
Date 20070927 20071112
Remark Original Drawing Revise Pad Connection
(38.1) 90.3 4.6 2.50.3
0.30.3 (1.1) (2.1) 100.3 (0.85) (0.75) P0.22x96-0.016=21.104 (A/A) 50.3
29.10.2 (Panel Size) 25.50.2 (Cap Size) 24.5 (Polarizer) 23.104 (V/A) 21.104 (A/A)
1.4 Mechanical Drawing
Univision Technology Inc.
(2.1) (1.1) 0.50.5 14
VCC VCOMH IREF SDA SCL
Display Pattern
RES#
VDD
80.3
VSS VBREF VBAT
W=0.350.03
3.504 (A/A)
Active Area 0.84" 96 x 16 Pixels
7.50.2 0.50.1 6.20.3
C1N C1P
Segment 127
( Column 1 )
Segment 32
( Column 96 )
P0.50x(14-1)=6.50.05
5.504 (V/A) 8.2 (Polarizer) 9.20.2 (Cap Size) 9.20.2 (Panel Size)
C2N
1
C2P
B
2-R0.40.1 3M #1318B 8.4x8x0.063mm
Common 0
( Row 16 )
Common 15
( Row 1 )
P0.22x16-0.016=3.504 (A/A)
1.60.1 Polarizer t=0.2mm 3.50.5 (Stiffener) 0.22 0.204 0.30.03 Glue Contact Side 0.204 0.22 Remove Tape t=0.15mm Max (1.6) (2.2) (0.6) (25.22) (30.7)
Display Pattern Scale (10:1)
(Reference Mechnical Design)
Notes:
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14
Symbol C2P C2N C1P C1N VBAT VBREF VSS VDD RES# SCL SDA IREF VCOMH VCC
Customer Approval Signature
Unless Otherwise Specified
Univision Technology Inc.
Unit
General Roughness
Drawing Number DMX9616CNGF03
Rev. B Material mm Title UG-9616GLBBG01 Folding Type OEL Display Module Pixel Number: 96 x 16, Monochrome, COG Package Soda Lime / Polyimide Tolerance 0.3 Dimension Angle 1 By Date Drawn Humphrey Lin 20071112 E.E. James Wang 20071112 Panel / E. Ivy Lo 20071112 P.M. Sean Lin 20071112 Scale 1:1 Sheet 1 of 1 Size A3
The drawing contained herein is the exclusive property of Univision. It is not allowed to copy, reproduce and or disclose in any formats without permission of Univision.
1. Color: Light Blue 2. Driver IC: SSD1306 3. FPC Number: UT-0206-P01 4. Interface: I2C 5. General Tolerance: 0.30 6. The total thickness (1.70 Max) is without polarizer protective film & remove tape. The actual assembled total thickness with above materials should be 1.95 Max.
Doc. No: SAS1-M003-B www..com
2
Univision Technology Inc.
1.5 Pin Definition Pin Number Power Supply Power Supply for Logic 8 VDD P Symbol Type
Doc. No: SAS1-M003-B www..com
Function
This is a voltage supply pin. It must be connected to external source.
Ground of OEL System 7 VSS P
This is a ground pin. It also acts as a reference for the logic pins, the OEL driving voltages, and the analog circuits. It must be connected to external ground.
Power Supply for OEL Panel 14 Driver Current Reference for Brightness Adjustment 12 IREF I
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5A.
VCC
P
This is the most positive voltage supply pin of the chip. It must be connected to external source.
Voltage Output High Level for COM Signal 13 VCOMH O
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
DC/DC Converter Power Supply for DC/DC Converter Circuit 5 VBAT P
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to VDD when the converter is used. It must be floated when the converter is not used.
Voltage Reference for DC/DC Converter Circuit 6 VBREF P
This pin is the internal voltage reference of booster circuit. A stabilization capacitor should be connected to VSS.
3/4 1/2 Interface
C1P / C1N C2P / C2N
I
Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost Capacitor
The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
Power Reset for Controller and Driver 9 RES# I
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
I2C Bus Clock Signal 10 SCL I
The transmission if information in the I2C bus is following a clock signal. Each transmission of data bit is taken place during a single clock period of this pin.
I2C Bus Data Signal 11 SDA I/O
This pin acts as a communication channel between the transmitter and the receiver.
3
Univision Technology Inc.
1.6 Block Diagram
Doc. No: SAS1-M003-B www..com
Active Area 0.84" 96 x 16 Pixels
Segment 127 Segment 32 Common 15 Common 0 R1 C4 C3
~~~
~
SSD1306
C1N VBAT VBREF SCL SDA C2N C1P C2P IREF VCOMH VCC VDD RES# VSS
C7
C6
R2 R3 C2 C5 C1
Pins connected to MCU interface: RES#, SCL, and SDA C1, C3, C6, C7: C3, C4: C5: R1: R2, R3: 1F 2.2F 22nF 820k, R1 = (Voltage at IREF - VSS) / IREF 2k
4
Univision Technology Inc.
2. Absolute Maximum Ratings
Parameter Supply Voltage for Logic Supply Voltage for Display Operating Temperature Storage Temperature Symbol VDD VCC TOP TSTG Min -0.3 0 -30 -40 Max 4 15 70 80
Doc. No: SAS1-M003-B www..com
Unit V V C C
Notes 1, 2 1, 2 -
Note 1: All the above voltages are on the basis of "GND = 0V". Note 2: When this module is used beyond the above absolute maximum ratings, permanent breakage of the module may occur. Also, for normal operations, it is desirable to use this module under the conditions according to Section 3. "Optics & Electrical Characteristics". If this module is used beyond these conditions, malfunctioning of the module can occur and the reliability of the module may deteriorate.
5
Univision Technology Inc.
3. Electrical Characteristics
3.1 Optics Characteristics Characteristics Brightness C.I.E. (Blue) Dark Room Contrast View Angle Symbol Lbr (x) (y) CR Conditions With Polarizer Without Polarizer Min
Doc. No: SAS1-M003-B www..com
Typ
Max Unit
100 120 cd/m2 0.12 0.16 0.20 0.22 0.26 0.30 - >2000:1 >160 degree
* Optical measurement taken at VDD = 2.8V, VCC = 7.25V. Software configuration follows Section 4.4 Initialization.
3.2 DC Characteristics Characteristics Supply Voltage for Logic Supply Voltage for DC/DC Supply Voltage for Display High Level Input Low Level Input High Level Output Low Level Output Operating Current for VDD Operating Current for VBAT Symbol VDD VBAT VCC VIH VIL VOH VOL IDD IBAT Conditions Note 3 Min 1.65 7 0.8xVDD 0 Typ Max Unit 2.8 7.25 3.3 4.2 7.5 VDD 0.2xVDD VDD V V V V V V
Internal DC/DC Enable 3.3
IOUT = 100A, 3.3MHz 0.9xVDD IOUT = 100A, 3.3MHz 0 Note 4 Note 5 Note 4 Note 5 -
0.1xVDD V 180 300 A 180 300 A 7.5 12.6 1 1 9.4 15.8 5 5 mA mA A A
Sleep Mode Current for VDD IDD, SLEEP Sleep Mode Current for VCC ICC, SLEEP
Note 3: Brightness (Lbr) and Supply Voltage for Display (VCC) are subject to the change of the panel characteristics and the customer's request. Note 4: VDD = 2.8V, VCC = 7.25V, 50% Display Area Turn on. Note 5: VDD = 2.8V, VCC = 7.25V, 100% Display Area Turn on. * Software configuration follows Section 4.4 Initialization.
6
Univision Technology Inc.
3.3 AC Characteristics Symbol tcycle tHSTART tHD tSD tSSTART tSSTOP tR tF Description Clock Cycle Time Start Condition Hold Time Data Hold Time (for "SDAOUT" Pin) Data Hold Time (for "SDAIN" Pin) Data Setup Time Start Condition Setup Time (Only relevant for a repeated Start condition) Stop Condition Setup Time Rise Time for Data and Clock Pin
Doc. No: SAS1-M003-B www..com
Min 2.5 0.6 0 300 100 0.6 0.6
Max 300 300
Unit us us ns ns us us ns ns us
Fall Time for Data and Clock Pin Idle Time before a New Transmission can tIDLE Start * (VDD - VSS = 2.8V, Ta = 25C)
1.3
-
7
Univision Technology Inc.
4. Functional Specification
4.1. Commands Refer to the Technical Manual for the SSD1306
Doc. No: SAS1-M003-B www..com
4.2 Power down and Power up Sequence To protect OEL panel and extend the panel life time, the driver IC power up/down routine should include a delay period between high voltage and low voltage power sources during turn on/off. It gives the OEL panel enough time to complete the action of charge and discharge before/after the operation. 4.2.1 Power up Sequence: 1. 2. 3. 4. 5. 6. Power up VDD Send Display off command Initialization Clear Screen Power up VCC Delay 100ms (When VCC is stable) 7. Send Display on command 4.2.2 Power down Sequence: 1. Send Display off command 2. Power down VCC 3. Delay 100ms (When VCC is reach 0 and panel is completely discharges) 4. Power down VDD
VDD on VCC on Display on VCC VDD VSS/Ground
Display off VCC off VDD off VCC VDD VSS/Ground
4.3 Reset Circuit When RES# input is low, the chip is initialized with the following status: 1. Display is OFF 2. 128x64 Display Mode 3. Normal segment and display data column and row address mapping (SEG0 mapped to column address 00h and COM0 mapped to row address 00h) 4. Shift register data clear in serial interface 5. Display start line is set at display RAM address 0 6. Column address counter is set at 0 7. Normal scan direction of the COM outputs 8. Contrast control register is set at 7Fh 9. Normal display mode (Equivalent to A4h command)
8
Univision Technology Inc.
4.4 Actual Application Example Command usage and explanation of an actual example
Doc. No: SAS1-M003-B www..com
Set Display Off 0xAE
Set Low Power Display Mode
0xD8, 0x05
Set VCOMH Deselect Level 0xDB, 0x20
Set Display Clock Divide Ratio/Oscillator Frequency
0xD5, 0x80
Set Segment Re-Map 0xA1
Set Entire Display On/Off 0xA4
Set Multiplex Ratio 0xA8, 0x0F
Set COM Output Scan Direction 0xC8
Set Normal/Inverse Display 0xA6
Set Display Offset 0xD3, 0x00
Set COM Pins Hardware Configuration 0xDA, 0x02
Clear Screen
Set Display Start Line 0x40
Set Contrast Control 0x81, 0xAF
Set Display On 0xAF
Set Charge Pump 0x8D, 0x14
Set Pre-Charge Period 0xD9, 0xF1
If the noise is accidentally occurred at the displaying window during the operation, please reset the display in order to recover the display function.
9
Univision Technology Inc.
5. Reliability
5.1 Contents of Reliability Tests Item High Temperature Operation Low Temperature Operation High Temperature Storage Low Temperature Storage Conditions 70C, 240 hrs -30C, 240 hrs 80C, 240 hrs -40C, 240 hrs
Doc. No: SAS1-M003-B www..com
Criteria
The operational functions work.
High Temperature/Humidity Operation 60C, 90% RH, 120 hrs -40C 85C, 24 cycles Thermal Shock 60 mins dwell * The samples used for the above tests do not include polarizer. * No moisture condensation is observed during tests.
5.2 Lifetime End of lifetime is specified as 50% of initial brightness reached. Parameter Storage Life Time Min 20,000 Max Unit hr hr Condition 120 cd/m2, 50% Checkerboard Ta = 25C, 50% RH Notes 6 Operating Life Time 10,000
Note 6: The average operating lifetime at room temperature is estimated by the accelerated operation at high temperature conditions.
5.3 Failure Check Standard After the completion of the described reliability test, the samples were left at room temperature for 2 hrs prior to conducting the failure test at 235C; 5515% RH.
10
Univision Technology Inc.
6. Outgoing Quality Control Specifications
6.1 Environment Required
Doc. No: SAS1-M003-B www..com
Customer's test & measurement are required to be conducted conditions: Temperature: Humidity: Fluorescent Lamp: Distance between the Panel & Lamp: Distance between the Panel & Eyes of the Inspector: Finger glove (or finger cover) must be worn by the inspector. Inspection table or jig must be anti-electrostatic.
under the following 23 5C 55 15 %RH 30W 50 cm 30 cm
6.2 Sampling Plan Level II, Normal Inspection, Single Sampling, MIL-STD-105E
6.3 Criteria & Acceptable Quality Level Partition Major Minor AQL 0.65 1.0 Definition Defects in Pattern Check (Display On) Defects in Cosmetic Check (Display Off)
6.3.1 Cosmetic Check (Display Off) in Non-Active Area Check Item Classification Criteria X > 6 mm (Along with Edge) Y > 1 mm (Perpendicular to edge)
X
Panel General Chipping
Minor
Y
X
Y
11
Univision Technology Inc.
Check Item Classification
Doc. No: SAS1-M003-B www..com
6.3.1 Cosmetic Check (Display Off) in Non-Active Area (Continued) Criteria Any crack is not allowable.
Panel Crack
Minor
Cupper Exposed (Even Pin or Film)
Minor
Not Allowable by Naked Eye Inspection
Film or Trace Damage
Minor
Not Allowable
Terminal Lead Twist
Minor
Not Allowable
Terminal Lead Broken
Minor
Terminal Lead Prober Mark
Acceptable
12
Univision Technology Inc.
Check Item Classification
Doc. No: SAS1-M003-B www..com
6.3.1 Cosmetic Check (Display Off) in Non-Active Area (Continued) Criteria NG if any bent lead cause lead shorting.
Minor
Terminal Lead Bent (Not Twist or Broken)
NG for horizontally bent lead more than 50% of its width.
Minor
Glue or Contamination on Pin (Couldn't Be Removed by Alcohol) Ink Marking on Back Side of panel (Exclude on Film)
Minor
Acceptable
Ignore for Any
13
Univision Technology Inc.
6.3.2 Cosmetic Check (Display Off) in Active Area Classification Check Item Any Dirt & Scratch on Acceptable Polarizer's Protective Film Scratches, Fiber, Line-Shape Defect Minor (On Polarizer) Dirt, Black Spot, Foreign Material, Minor (On Polarizer)
Doc. No: SAS1-M003-B www..com
Criteria Ignore for not Affect the Polarizer W 0.1 Ignore W > 0.1, L 2 n1 L>2 n=0 0.1 Ignore 0.1 < 0.25 n1 0.25 < n=0 0.5 Ignore if no Influence on Display 0.5 < n=0
Dent, Bubbles, White spot (Any Transparent Spot on Polarizer)
Minor
Fingerprint, Flow Mark Minor Not Allowable (On Polarizer) * Protective film should not be tear off when cosmetic check. ** Definition of W & L & (Unit: mm): = (a + b) / 2
L
b: Minor Axis W a: Major Axis
14
Univision Technology Inc.
6.3.3 Pattern Check (Display On) in Active Area Check Item Classification
Doc. No: SAS1-M003-B www..com
Criteria
No Display
Major
Flicker
Major
Not Allowable
Missing Line
Major
Pixel Short
Major
Darker Pixel
Major
Wrong Display
Major
Un-uniform
Major
15
Univision Technology Inc.
7. Package Specifications
EPE COVER FOAM 351x212x1, ANTISTATIC x 1 Pcs x 1 pcs (Empty)
Doc. No: SAS1-M003-B www..com
16 Pcs Tray Vacuum packing B Module x 15 pcs A Staggered Stacking EPE PROTECTTIVE
Tray 420x285 T=0.8mm
Exsiccator x 2 pcs Brimary Primary Box 4 SET C SET
Wrapped with adhesive tape x 16 pcs B
Vacuum packing bag
EPE PROTECTTIVE 370mm x 280mm x 20mm
CARTON BOX
Label
Primary L450mm x W296 x H110, B wave xC 4Pcs
Univision Technology Inc. Part ID :
Label
Lot ID : Q'ty : QC :
Carton Box L464mm x W313mm x H472mm, AB wave
(Major / Maximum)
Item Holding Trays Total Trays Primary Box (A) (B) (C) 15 16 1~4
Quantity per Primary Box per Primary Box (Including 1 Empty Tray) per Carton (4 as Major / Maximum)
16
Univision Technology Inc.
8. Precautions When Using These OEL Display Modules
8.1 Handling Precautions 1) 2) 3)
Doc. No: SAS1-M003-B www..com
4) 5)
6)
Since the display panel is being made of glass, do not apply mechanical impacts such us dropping from a high position. If the display panel is broken by some accident and the internal organic substance leaks out, be careful not to inhale nor lick the organic substance. If pressure is applied to the display surface or its neighborhood of the OEL display module, the cell structure may be damaged and be careful not to apply pressure to these sections. The polarizer covering the surface of the OEL display module is soft and easily scratched. Please be careful when handling the OEL display module. When the surface of the polarizer of the OEL display module has soil, clean the surface. It takes advantage of by using following adhesion tape. * Scotch Mending Tape No. 810 or an equivalent Never try to breathe upon the soiled surface nor wipe the surface using cloth containing solvent such as ethyl alcohol, since the surface of the polarizer will become cloudy. Also, pay attention that the following liquid and solvent may spoil the polarizer: * Water * Ketone * Aromatic Solvents Hold OEL display module very carefully when placing OEL display module into the system housing. Do not apply excessive stress or pressure to OEL display module. And, do not over bend the film with electrode pattern layouts. These stresses will influence the display performance. Also, secure sufficient rigidity for the outer cases.
7) 8) 9) 10)
Do not apply stress to the LSI chips and the surrounding molded sections. Do not disassemble nor modify the OEL display module. Do not apply input signals while the logic power is off. Pay sufficient attention to the working environments when handing OEL display modules to prevent occurrence of element breakage accidents by static electricity. * Be sure to make human body grounding when handling OEL display modules. * Be sure to ground tools to use or assembly such as soldering irons. * To suppress generation of static electricity, avoid carrying out assembly work under dry environments. * Protective film is being applied to the surface of the display panel of the OEL display module. Be careful since static electricity may be generated when exfoliating the protective film.
17
Univision Technology Inc.
Doc. No: SAS1-M003-B www..com
11) Protection film is being applied to the surface of the display panel and removes the protection film before assembling it. At this time, if the OEL display module has been stored for a long period of time, residue adhesive material of the protection film may remain on the surface of the display panel after removed of the film. In such case, remove the residue material by the method introduced in the above Section 5). 12) If electric current is applied when the OEL display module is being dewed or when it is placed under high humidity environments, the electrodes may be corroded and be careful to avoid the above.
8.2 Storage Precautions 1) When storing OEL display modules, put them in static electricity preventive bags avoiding exposure to direct sun light nor to lights of fluorescent lamps, etc. and, also, avoiding high temperature and high humidity environments or low temperature (less than 0C) environments. (We recommend you to store these modules in the packaged state when they were shipped from Univision Technology Inc.) At that time, be careful not to let water drops adhere to the packages or bags nor let dewing occur with them. If electric current is applied when water drops are adhering to the surface of the OEL display module, when the OEL display module is being dewed or when it is placed under high humidity environments, the electrodes may be corroded and be careful about the above.
2)
8.3 Designing Precautions 1) The absolute maximum ratings are the ratings which cannot be exceeded for OEL display module, and if these values are exceeded, panel damage may be happen. To prevent occurrence of malfunctioning by noise, pay attention to satisfy the VIL and VIH specifications and, at the same time, to make the signal line cable as short as possible. We recommend you to install excess current preventive unit (fuses, etc.) to the power circuit (VDD). (Recommend value: 0.5A) Pay sufficient attention to avoid occurrence of mutual noise interference with the neighboring devices. As for EMI, take necessary measures on the equipment side basically. When fastening the OEL display module, fasten the external plastic housing section. If power supply to the OEL display module is forcibly shut down by such errors as taking out the main battery while the OEL display panel is in operation, we cannot guarantee the quality of this OEL display module. The electric potential to be connected to the rear face of the IC chip should be as follows: SSD1306 * Connection (contact) to any other potential than the above may lead to rupture of the IC.
2)
3) 4) 5) 6) 7)
8)
18
Univision Technology Inc.
8.4 Precautions when disposing of the OEL display modules 1)
Doc. No: SAS1-M003-B www..com
Request the qualified companies to handle industrial wastes when disposing of the OEL display modules. Or, when burning them, be sure to observe the environmental and hygienic laws and regulations.
8.5 Other Precautions 1) When an OEL display module is operated for a long of time with fixed pattern may remain as an after image or slight contrast deviation may occur. Nonetheless, if the operation is interrupted and left unused for a while, normal state can be restored. Also, there will be no problem in the reliability of the module. To protect OEL display modules from performance drops by static electricity rapture, etc., do not touch the following sections whenever possible while handling the OEL display modules. * Pins and electrodes * Pattern layouts such as the FPC With this OEL display module, the OEL driver is being exposed. Generally speaking, semiconductor elements change their characteristics when light is radiated according to the principle of the solar battery. Consequently, if this OEL driver is exposed to light, malfunctioning may occur. * Design the product and installation method so that the OEL driver may be shielded from light in actual usage. * Design the product and installation method so that the OEL driver may be shielded from light during the inspection processes. Although this OEL display module stores the operation state data by the commands and the indication data, when excessive external noise, etc. enters into the module, the internal status may be changed. It therefore is necessary to take appropriate measures to suppress noise generation or to protect from influences of noise on the system design. We recommend you to construct its software to make periodical refreshment of the operation statuses (re-setting of the commands and re-transference of the display data) to cope with catastrophic noise.
2)
3)
4)
5)
19

▲Up To Search▲

Price & Availability of UG-9616GLBBG01

	To Download UG-9616GLBBG01 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .