|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
www..com Specification for G104SN03 V2 06 / Feb / 04 .com DataShe e Data Modul AG - Landsberger Str. 322 - 80687 Munchen - Tel. 089-56017-0 - Fax 089-56017-119 - www.data-modul.de .com DataSheet 4 U .com www..com Version: 1.0 Total Pages: 28 Date: February 6, 2004 Product Functional Specification 10.4 inch SVGA Color TFT LCD Module Model Name: G104SN03 V.2 t4U.com e DataShe .com (u) Preliminary Specification ( ) Final Specification Note: This Specification is subject to change without notice. .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 2/28 DataSheet4 U .com www..com I. Contents 1.0 2.0 Handling Precautions General Description 2.1 Display Characteristics 2.2 Functional Block Diagram Absolute Maximum Ratings Optical Characteristics Signal Interface 5.1 Connectors 5.2 Signal Pin 5.3 Signal Description 5.4 Signal Electrical Characteristics Pixel Format Image Power Consumption Interface Timing 8.1 Display Color v.s. Input Data Signal 8.2 Input Signal Timing 8.3 Display Position 5 6 3.0 4.0 5.0 9 10 12 6.0 7.0 8.0 16 17 19 t4U.com e DataShe 9.0 Backlight Characteristics 23 .com 10.0 Touch Panel Specification..........................................................24 10.1 Operating Condition 10.2 Electrical Characteristic 10.3 Mechanical Characteristic 10.4 Touch Panel Outline Dimension 11.0 Reliability Test Items 12.0 Display Quality 13.0 Packing Dimension 14.0 Mechanical Characteristic 26 26 27 28 .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 3/28 DataSheet 4 U .com www..com II. Record of Revision Version and Date Page 1.0 Feb. 6, 2004 All Old description N/A New Description First Edition for Customers Remark t4U.com e DataShe .com .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 4/28 4 DataSheet U .com www..com 1.0 Handing Precautions 1) Since front polarizer is easily damaged, pay attention not to scratch it. 2) Be sure to turn off power supply when inserting or disconnection from input connector. 3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. 4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. 5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. 6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. 7) Do not open nor modify the module Assembly. 8) Do not press the reflector sheet at the back of the module to any directions. 9) In case if a module has to be put back into the packing container slot after once it was taken out from the container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT module may be damaged. 10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the interface Connector of the TFT module. 11) After installation of the TFT module into an enclosure, do not twist nor bend the TFT module even momentary. At designing the enclosure, it should be taken into consideration that no t4U.com bending/twisting forces are applied to the TFT module from outside. Otherwise the TFT module .com 12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local e DataShe may be damaged. ordinances or regulations for disposal. 13) Small amount of materials having no flammability grade is used in the LCD module should be supplied by power complied with requirements of Limited Power Source, or be applied exemption. 14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit. Do not connect the CFL in Hazardous Voltage Circuit. .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 5/28 DataSheet 4 U .com www..com 2.0 General Description This specification applies to the 10.4 inch color TFT LCD module G104SN03 V.2. This module is designed for General Display. The screen format is intended to support the SVGA (800(H) x 600(V)) screen and 262k colors (RGB 6-bits data driver). All input signals are LVDS interface compatible. The module does not contain an inverter card for backlight. Features - SVGA 800(H) x600(V) resolution - 1 CCFL(Cold cathode Fluorescent Lamp) - High contrast ratio, High transmittance ratio - Wide viewing angle - High speed response - Low power consumption - LVDS interface t4U.com Applications Information Appliance Industrial Application .com e DataShe .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 6/28 DataSheet 4 U .com www..com 2.1 Display Characteristics The following items are characteristics summary on the table under 25 condition Items Screen Diagonal Outline dimension Active Area Resolution H x V Pixel Pitch Pixel Arrangement Display Mode Typical White Luminance (ICFL=4.5 mA) Contrast Ratio Optical Rise Time/Fall Time Viewing angle (CR10) Nominal Input Voltage VDD Typical Power Consumption (VDD line + VCFL line) Unit [inch] [mm] [mm] 10.4" Specifications 236.0(W) x 174.3(H) x 7.4(D) 211.2(H) x 158.4(V) 800(R, G,B x3) x 600 [mm] 0.264(H) x 0.264(V) R.G.B. Vertical Stripe TN mode, Normally White [cd/m ] 2 180 Typ. (center) 5001 Typ. [msec] 10/25 Typ. 60/60/35/65 (L/R/U/D) [Volt] [Watt] +3.3 Typ. 3.3 Typ t4U.com Weight Surface treatment Electrical Interface Support Color Temperature Range Operating Storage(Shipping) [Grams] 400 Typ 10 Anti-glare,hard coating 3H e DataShe .com channel LVDS 1 Native 262K colors (RGB 6-bit driver) [] [] 0 to +50 -20 to +60 .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 7/28 DataSheet 4 U .com www..com 2.2 Functional Block Diagram The following diagram shows the functional block of the 10.4 inches Color TFT LCD Module t4U.com e DataShe .com .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 8/28 DataSheet 4 U .com www..com 3.0 Absolute Maximum Ratings Parameter Symbol Min. Power voltage Input signal voltage CCFL current CCFL starting Voltage Operating temperature Operating Humidity Storage temperature Storage Humidity Vibration Shock VDD Vin ICFL Vs Top HOP TST HST -0.3 -0.3 3.0 0 8 -20 5 Values Max. 4 VDD+0.3 5.5 800 +50 90 +60 90 1.5,10~200~1 200,2 [Volt] [Volt] [mA]rms [Vrms] [] [%RH] [] [%RH] [G,Hz] [G,ms] Unit (GND = 0 V) Remark At 25 At 25 AT 25 Note 1 Note 1 Note 1 Note 1 Half sine wave Note 1:The relative humidity must not exceed 90% non-condensing at temperatures of 40 or less. At temperatures greater than 40 , the wet bulb temperature must not exceed 39 . When operate at low temperatures, the brightness of CCFL will drop and the life time of CCFL will be reduced. Note 2:The unit should not be exposed to corrosive chemicals. t4U.com Wet bulb temperature chart e DataShe .com Twb=39C Operating Range Storage Range .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 9/28 DataSheet4 U .com www..com 4.0 Optical Characteristics (Note 1, Note 2) Item Response time Rising time Falling time Contrast ratio Viewing angle Top Bottom Left Right Symbol Condition Specification Min. 400 30 60 60 60 160 0.280 0.300 0.540 0.290 0.270 0.530 0.115 0.100 13 Points Typ. 10 25 500 35 65 60 60 180 0.320 0.330 0.570 0.320 0.300 0.560 0.145 0.130 Max. 20 30 0.340 0.360 0.600 0.350 0.330 0.590 0.175 0.160 1.33 Note 3,9,10 Unit Remark Tr Tf CR =0 =0 ms Note 4 Note 3,5 CR10 deg. nit Note 3,6 Note 3,7,8,9 Note 3,8,9 White Luminance (ICFL=4.5 mA) Color chromaticity(CIE) [cd/m 2] Wx Wy Rx Ry Gx Gy Bx By W =0 =0 t4U.com White uniformity e DataShe Note 1: Ambient temperature = 25. .com Note 2: To be measured in dark room after backlight warm up 30 minutes. Note 3: To be measured with a viewing cone of 1by Topcon luminance meter BM-5A. Note 4: Definition of response time: The output signals of BM-7 are measured when the input signals are changed from "Black" to "White" (falling time) and from "White" to "Black" (rising time), respectively. The response time means the interval between the 10% and 90% of amplitudes. Refer to figure as below. "White" Sig nal (R ela tiv e 10% 0% 100% 90% "Black" "White" Tr Tf Note 5. Definition of contrast ratio: Contrast ratio is calculated with the following formula. Contrast ratio (CR)= .com Luminance on the white raster Luminance on the black raster G104SN03 V.2 10/28 (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. DataSheet4 U .com www..com Note 6: Definition of viewing angle: Note 7: Definition of the 13 points (from A to M) on panel, refer to figure as below t4U.com e DataShe .com Note 8: Definition of brightness: the luminance of center points (G). Note 9: Driving conditions for CCFL : IL=4.5 mA, 60KHz Frequency Note 10: Definition of white uniformity: Maximum Luminance of thirteen points (brightness) Minimum Luminance of thirteen points (brightness) w = .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 11/28 DataSheet4 U .com www..com 5.0 Signal Interface 5.1 Connectors Physical interface is described as for the connector on module. These connectors are capable of accommodating the following signals and will be following components. Connector Name / Designation Manufacturer Type / Part Number Mating Connector / Part Number Mating Connector / Part Number Connector Name / Designation Manufacturer Type / Part Number Mating Connector / Part Number For Signal Connector HIROSE HRS DF 19K-20P-1H HRS DF19G-20S-1C (WIRE TYPE)) HRS DF19-20S-1F (FPC TYPE) For Lamp Connector JST BHSR-02VS-1 SM02B-BHSS-1-TB 5.2 Signal Pin Pin assignment (1)Input signal interface t4U.com Pin no 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 Symbol VCC VCC GND GND RxIN0RxIN0+ GND RxIN1RxIN1+ GND RxIN2RxIN2+ GND CKINCKIN+ GND NC NC GND GND Ground No Connection No Connection Ground Ground G104SN03 V.2 12/28 Ground LVDS receiver signal clock Ground LVDS receiver signal channel 2 Ground LVDS receiver signal channel 1 Function +3.3 V power supply +3.3 V power supply Ground Ground LVDS receiver signal channel 0 Etc. e DataShe .com .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. DataSheet4 U .com www..com (2)LVDS transmitter/receiver signal mapping Symbol TxIN0 TxIN1 TxIN2 TxIN3 TxIN4 TxIN5 TxIN6 TxIN7 TxIN8 TxIN9 TxIN10 TxIN11 TxIN12 TxIN13 R0 R1 R2 R3 R4 R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3 B4 B5 Hs Vs DE CLK Red data (LSB) Red data Red data Red data Red data Red data (MSB) Green data (LSB) Green data Green data Green data Green data Green data (MSB) Blue data (LSB) Blue data Blue data Blue data 6 bits blue display data 6 bit green display data 6 bit red display data Function t4U.com TxIN14 TxIN15 TxIN16 TxIN17 TxIN18 TxIN19 TxIN20 TxCLKIN e DataShe .com Blue data Blue data (MSB) Horizontal sync. Vertical sync. Data enable Clock Dot clock .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 13/28 DataSheet 4 U .com www..com 5.3 Signal Description The module using a LVDS receiver. LVDS is a differential signal technology for LCD interface and high speed data transfer device. Transmitter shall be SN75LVDS84 (negative edge sampling) or compatible. NoteInput signals shall be low or Hi-Z state when VDD is off. Signal Name RxIN0-, RxIN0+ RxIN1-, RxIN1+ RxIN2-, RxIN2+ CKIN-, CKIN+ VDD GND NC Description LVDS differential data input (Red0-Red5, Green0) LVDS differential data input (Green1-Green5, Blue0-Blue1) LVDS differential data input (Blue2-Blue5, Hsync, Vsync, DE) LVDS differential clock input +3.3V Power Supply Ground No Connection Signal Name Description Red Data 5 (MSB) Red-pixel Data Red Data 4 Each red pixel's brightness data consists of these Red Data 3 6 bits pixel data. .com Red Data 2 Red Data 1 Red Data 0 (LSB) Red-pixel Data Green Data 5 (MSB) Green Data 4 Green Data 3 Green Data 2 Green Data 1 Green Data 0 (LSB) Green-pixel Data Blue Data 5 (MSB) Blue Data 4 Blue Data 3 Blue Data 2 Blue Data 1 Blue Data 0 (LSB) Blue-pixel Data Data Clock Green-pixel Data Each green pixel's brightness data consists of these 6 bits pixel data. t4U.com +RED5 +RED4 +RED3 +RED2 +RED1 +RED0 +GREEN5 +GREEN4 +GREEN3 +GREEN2 +GREEN1 +GREEN0 +BLUE5 +BLUE4 +BLUE3 +BLUE2 +BLUE1 +BLUE0 CLK e DataShe Blue-pixel Data Each blue pixel's brightness data consists of these 6 bits pixel data. DE Display Timing VSYNC HSYNC Vertical Sync Horizontal Sync The typical frequency is 40MHz. The signal is used to strobe the pixel data and DE signals. All pixel data shall be valid at the falling edge when the DE signal is high. This signal is strobed at the falling edge of CLK. When the signal is high, the pixel data shall be valid to be displayed. The signal is synchronized to CLK. The signal is synchronized to CLK. NoteOutput signals from any system shall be low or Hi-Z state when VDD is off. .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 14/28 DataSheet 4 U .com www..com 5.4 Signal Electrical Characteristics Input signals shall be low or Hi-Z state when VDD is off. It is recommended to refer the specifications of SN75LVDS86(Texas Instruments) in detail. Signal electrical characteristics are as follows Item The differential level The common mode input voltage The input setup time The input hold time High-level input voltage Low-level input voltage Clock frequency Symbol VID VIC tsu thd VIAP VIAM CLK 31 Min. 0.1 VID 2 0.5 0.5 2.0 0.8 68 Typ. 2.4 Max. 0.6 VID 2 Unit V V ns ns V V MHz t4U.com e DataShe .com .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 15/28 DataSheet 4 U .com www..com 6.0 Pixel Format Image Following figure shows the relationship of the input signals and LCD pixel format 1 1st Line 2 799 800 RGBRGB RGBRGB 600th Line t4U.com RGBRGB RGBRGB e DataShe .com .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 16/28 DataSheet 4 U .com www..com 7.0 Power Consumption Input power specifications are as follows Item Power supply voltage Input voltage Current consumption Inrush current Internal logic Low voltage High voltage I Symbol V CC IA IB RUSH Min. 3.0 Typ. 3.3 230 260 Max. 3.6 Unit V mArms Remark Note 1 310 1500 0.3 V CC VCC 100 mArms mApeak Note 2 0 0.7VCC - 0.76 VIL VIH VRP PDD Power ripple voltage LCD Drive power consumption mVp-p [Watt] Note 1:Effective value (mArms) at VCC = 3.3 V/25. Black (0) 63 IA IB Gray (7) 63 t4U.com White 64 Grayscale e DataShe .com Black Vertical stripe line Note 2: Refer to the following power-on condition. 90% Vcc 10% Sequence of Power-on/off and signal-on/off Ton=470s10% T3 T4 50msT180msec T2 0T270msec 300msecT3 300msecT4 T510msec Power T1 T5 Input signal .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 17/28 DataSheet 4 U .com www..com Apply the lamp voltage within the LCD operating range. When the backlight turns on before the LCD operation or the LCD turns off before the backlight turns off, the display may momentarily become abnormal. Caution The above on/off sequence should be applied to avoid abnormal function in the display. In case of handling: Make sure to turn off the power when you plug the cable into the input connector or pull the cable out of the connector. t4U.com e DataShe .com .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 18/28 DataSheet4 U .com www..com 8.0 Interface Timings 8.1 Display color v.s. input data signals: Data signal (0 : Low level, 1: High level) R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 B0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 0 0 0 1 1 0 0 1 1 0 0 1 0 0 1 1 0 0 1 1 0 1 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 0 0 0 1 1 1 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 0 1 0 1 0 1 0 1 0 0 0 Display colors Black Blue Red Magenta Green Cyan Yellow White Black Dark bright Basic colors Red grayscale t4U.com Red Black Dark bright 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 e DataShe 00000 .com Green grayscale Green Black Dark bright 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 1 1 1 0 0 0 0 1 1 0 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 1 0 Blue grayscale Blue 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 0 1 1 1 0 1 Note : Each basic color can be displayed in 64 gray scales using the 6 bit data signals. By combining the 18-bit data signals(R, G, B), the 262, 144 colors can be achieved on the display. .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 19/28 DataSheet 4 U .com www..com 8.2. Input signal timing (1). Timing characteristics of input signals (a) DE mode Item Clock frequency Horizontal blanking Vertical blanking Symbol Fck Thb1 Tvb1 Min. 36 18 3 Typ. 40 256 28 Max. 50 624 184 Unit MHz Clk Th Remark (b) HV mode Item Clock frequency Hsync period Hsync pulse width Hsync front porch Hsync back porch Hsync blanking Vsync period Symbol Fck Th Thw Thf Thb Thb1 Tv Tvw Min. 36 818 2 8 4 18 603 1 Typ. 40 1056 128 40 88 256 628 4 Max. 50 1424 624 784 184 Unit MHz Clk Clk Clk Clk Clk Th Th Th Th Clk Remark t4U.com Vsync pulse width Vsync front porch Vsync blanking Hsync/Vsync phase shift e DataShe .com1 Tvf 0 Tvb1 Tvpd 3 2 28 320 Item Horizontal start Symbo Value l display The 218 Unit Clk Description After falling edge of Hsync, counting 218clk, then getting valid data from 219th clk's data. After falling edge of Vsync, counti ng 25th, then getting 26th Th 's data. Vertical display start Tve 25 Th .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 20/28 DataSheet 4 U .com www..com (2). Timing Definition: 1056 dot H-Sync 40 dot 88 dot 128 dot DE 800 dot 628H V-Sync 1H 4H DE 28H t4U.com 23H 600H e DataShe .com .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 21/28 DataSheet 4 U .com t4U.com .com DataSheet 4 U .com Tv Tvw Th Tve Invalid X,1 X,2 X,3 X,599 X,600 Invalid www..com (3)Timing Chart: Vs Tvf Tvbl Thb Tvd Tvf Hs RGB Thw X,599 X,600 (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. Th Thf invalid 1,Y 2,Y 3,Y DE Hs CLK The Thf 799,Y 800,Y invalid RGB Thbl Thd .com G104SN03 V.2 RGB,DE,Hs CLK VIH VIL VIH VIL 800,Y DE (1 pixel / clock) Vs VIH VIL Hs Tvpd VIH VIL Tds,Tes,Ths Tdh,Teh,Thh Tch Tcl 22/28 Timing chart e DataShe www..com 8.3. Display position D( 1,1 ) D( 1,2 ) . . . D( 1,Y ) . . . D( 1,599 ) D( 1,600 ) D( 2,1 ) D( 2,2 ) D( 2,Y ) D( 2,599 ) D( 2,600 ) ...... ...... ...... ...... ...... ...... ...... D( X,1 ) D( X,2 ) . . . D( X,Y ) . . . D( X,599 ) D( X,600 ) ...... ...... ...... ...... ...... ...... ...... D( 799,1 ) D( 800,1 ) D( 799,2 ) D( 800,2 ) . . . . . . D( 799,Y ) D( 800,Y ) . . . . . . D( 799,599) D( 800,599 ) D( 799,600) D( 800,600) 9.0 Backlight Characteristic Backlight driving conditions Parameter Lamp voltage Lamp current Power consumption Lamp starting voltage Frequency Lamp life time Symbol VL IL PL VS FL LL Min. 510 3.0 10000 Typ. 560 4.5 2.52 60 20000 Max. 610 5.5 1050 800 Unit Vrms mArms W Vrms KHZ Hr Remark Note 1 Note 1 Note 2 T=0 T=25 Note 3 Note 1, 4 t4U.com Note 1: T= 25, IL = 4.5mA Note 2: Inverter should be designed with the characteristic of lamp. When you are designing .com the inverter, the output voltage of the inverter should comply with the following conditions. (1). The area under the positive and negative cycles of the waveform of the lamp current and lamp voltage should be area symmetric(the symmetric ratio should be larger than 90%). (2). There should not be any spikes in the waveform. (3). The waveform should be sine wave as possible. (4). Lamp current should not exceed the maximum value within the operating Temperature (It is prohibited to over the maximum lamp current even if operated in The non-guaranteed temperature). When lamp current over the maximum value for a long time, it may cause fire. Therefore, it is recommend that the inverter should have the current limited circuit. Note 3: Lamp frequency may produce interference with horizontal synchronous frequency and this may cause line flow on the display. Therefore lamp frequency shall be detached from the horizontal synchronous frequency and its harmonics as far as possible in order to avoid interference. Note 4: Brightness (IL=4.5mA) to be decrease to the 50% of the initial value. e DataShe Signal for Lamp connector Pin no. 1 2 Symbol H L Function CCFL power supply(H.V.) CCFL power supply(GND) Remark Cable color: Pink Cable color: White .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 23/28 DataSheet 4 U .com www..com 10.0 Touch Panel Specification 10.1 Operating condition Item Operating voltage Min. Typ. 5 Max. Unit V DC Remark 10.2 Electrical characteristic Item Min. XH-XL YH-YL X-Y X Y 200 200 20 Typ. 500 500 Max. 800 800 1.5 1.5 Unit M % % Terminal Resistance Insulation resistance Linearity 10.3 t4U.com Mechanical characteristic Item Min. Typ. Max. 120 Unit g H Pen/Finger input pressure Surface hardness e DataShe 3 .com CN3: FFC tail Pin. No. 1 2 3 4 Symbol XH YH XL YL Description High voltage terminal along X-axis High voltage terminal along Y-axis Low voltage terminal along X-axis Low voltage terminal along Y-axis .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 24/28 DataSheet4 U .com www..com 10.4 Touch Panel Outline Dimension t4U.com e DataShe .com .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 25/28 DataSheet 4 U .com www..com 11.0 Reliability test items Test tem High temperature storage Test Condition 70, 300Hrs Remark Note 1, 2 , 3 Low temperature storage -20, 300Hrs Note 1, 2 , 3 High temperature & high humidity operation 40, 90%RH, 300Hrs (No condensation) Note 1, 2 , 3 High temperature operation 50, 300Hrs Note 1, 2 , 3 Low temperature operation 0, 300Hrs -20~60 1H, 10mins, 1H, 5cycles Note 1, 2 , 3 t4U.com Temperature cycling (non-operation) Electrostatic discharge (non-operation) Vibration (non-operation) Mechanical shock (non-operation) Note 1, 2 , 3 e DataShe .com 150 pF,150,10kV,1 second, 8 position on the panel, 10 times each place Sweep:1.5G, 10H Z ~ 200H Z ~ 10HZ /2.5min X, Y, Z, 3 directions 50G/18ms, 200G/2ms, X, Y, Z once for each direction Note 3 Note 1, 2 , 3 Note 1, 2 , 3 Note 1: Evaluation should be tested after storage at room temperature for one hour. Note 2: There should be no change which might affect the practical display function when the display quality test is conducted under normal operating condition. Note 3: Judgment:1. Function OK 2. No serious image quality degradation 12.0 Display quality The display quality of the color TFT-LCD module should be in compliance with the AUO's OQC inspection standard. .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 26/28 DataSheet 4 U .com www..com 13.0 Packing Dimension: LCD Module Anti-Static Bag EPP Cushion t4U.com NOTE : .com 1. Max. Capacity : 30 LCD Modules/Carton. 2. Max. Weight : 13Kg/Carton. 3. Meas : 448 mm*402mm*350mm. Carton e DataShe .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 27/28 DataSheet4 U .com www..com 14.0 Mechanical Characteristic LCM outline dimensions t4U.com e DataShe .com .com (C) Copyright AU Optronics, Inc. 2004 All Right Reserved. No Reproduction and Redistribution Allowed. G104SN03 V.2 28/28 4 DataSheet U .com www..com Data Modul Aktiengesellschaft Landsberger Str. 322 D-80687 Munchen Tel.: +49 -89 -56017 -0 Fax: +49 -89 -56017 -119 Data Modul Sales Office Hamburg An der Alster 48 D-20099 Hamburg Tel.: +49 -40 -280158 -0 Fax: +49 -40 -280158 -19 Data Modul Sales Office Dusseldorf Fritz-Vomfelde-Str. 8 D-40547 Dusseldorf Tel.: +49 -211 -52709 -0 Fax: +49 -211 -52709 -19 t4U.com .com Data Modul Sales Office Stuttgart Friedrich-List-Str. 42 D-70771 LeinfeldenEchterdingen Tel.: +49 -711 -794613 -5 Fax: +49 -711 -794613 -7 Data Modul Sales Office Frankfurt frankfurt@data-modul.de Tel.: +49 -671 -92087 -12 Fax: +49 -671 -92087 -14 Data Modul Inc. 1767-46 Veterans Memorial Highway Islandia NY 11749 USA Tel.: +1 -631 -951 -0800 Fax: +1 -631 -951 -2121 .com www.data-modul.de tft@data-modul.de DataSheet 4 U .com |
Price & Availability of G104SN03V2 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |