View TDA3664AT_5029097.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
Rev. 07 -- 25 June 2007 Product data sheet
1. General description
The TDA3664 is a fixed voltage regulator with very low dropout voltage/quiescent current, which operates over a wide supply voltage range. The regulator is available as:
* TDA3664: SO4 package * TDA3664AT: SO8 package * TDA3664TT: TSSOP8 package
2. Features
I I I I I I Fixed 5 V, 100 mA regulator Supply voltage range up to 45 V Very low quiescent current of 15 A (typical value) Very low dropout voltage High ripple rejection Protections: N Reverse polarity safe (down to -25 V without high reverse current) N Negative transient of 50 V (RS = 10 ; t < 100 ms) N Able to withstand voltages up to 18 V at the output (supply line may be short-circuited) N ESD protection on all pins N DC short-circuit safe to ground and VP of the regulator output N Temperature protection (Tj > 150 C)
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
3. Quick reference data
Table 1. Quick reference data VP = 14.4 V; Tamb = 25 C; measured with test circuit of Figure 15; unless otherwise specified. Symbol VP Iq Parameter supply voltage quiescent current Conditions regulator on VP = 4.5 V; IREG = 0 mA VP = 14.4 V; IREG = 0 mA 6 V VP 22 V ; IREG = 10 mA 6 V VP 22 V ; IREG = 50 mA Regulator output: pin REG VREG output voltage 8 V VP 22 V ; IREG = 0.5 mA 6 V VP 45 V; IREG = 0.5 mA 0.5 mA IREG 100 mA 6 V VP 45 V VREG(drop) dropout voltage VP = 4.5 V; IREG = 50 mA; Tamb 85 C
[2] [1]
Min 3 -
Typ 14.4 10 15 0.2 1.4
Max 45 30 0.5 2.5
Unit V A A mA mA
Supply voltage
4.8 4.75
5.0 5.0
5.2 5.25
V V
4.75 4.75 -
5.0 5.0 0.18
5.25 5.25 0.3
V V V
[1] [2]
The regulator output will follow VP if VP < VREG + VREG(drop) TDA3664TT: IREG 15 mA at Tamb 125 C; IREG 30 mA at Tamb 85 C.
4. Ordering information
Table 2: Ordering information Package Name TDA3664AT TDA3664 TDA3664TT SO8 SO4 TSSOP8 Description plastic small outline package; 8 leads; body width 3.9 mm plastic small outline package; 4 leads; body width 3.5 mm plastic thin shrink small outline package; 8 leads; body width 3 mm Version SOT96-1 SOT223-1 SOT505-1 Type number
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
2 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
5. Block diagram
VP
1 (8) REGULATOR BANDGAP 3 (1) REG
TDA3664 (TDA3664AT) (TDA3664TT)
THERMAL PROTECTION 2, 4 (3)
mgl809
GND
Pin numbers in parenthesis refer to the TDA3664AT and TDA3664TT version.
Fig 1. Block diagram
6. Pinning information
6.1 Pinning
VP GND
1
REG n.c.
1 2 3 4
001aac948
8
VP
2
TDA3664 4 GND
GND n.c.
001aac947
7 n.c. TDA3664AT TDA3664TT 6 n.c. 5 n.c.
REG
3
Fig 2. Pin configuration SO4
Fig 3. Pin configuration SO8 and TSSOP8
6.2 Pin description
Table 3: Symbol VP GND REG n.c. Pin description Pin SO4 1 2 and 4 3 SO8 8 3 1 TSSOP8 8 3 1 supply voltage ground regulator output Description
2, 4, 5, 6 and 7 2, 4, 5, 6 and 7 not connected
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
3 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
7. Functional description
The TDA3664 is a fixed 5 V regulator which can deliver output currents up to 100 mA. The regulator is available in SO8, TSSOP8 and SO4 packages. The regulator is intended for portable, mains and telephone applications. To increase the lifetime of batteries, a specially built-in clamp circuit keeps the quiescent current of this regulator very low, also in dropout and full load conditions. The regulator remains operational down to very low supply voltages, below which it switches off. A temperature protection is included, which switches the regulator output off at IC temperatures above 150 C.
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
4 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
8. Limiting values
Table 4: Limiting values In accordance with the Absolute Maximum Rating System (IEC 60134). Symbol VP VP(rp) Ptot Parameter supply voltage reverse polarity supply voltage total power dissipation TDA3664AT TDA3664TT TDA3664 Tstg Tamb Tj storage temperature ambient temperature junction temperature non-operating operating operating non-operating temperature of copper area is 25 C -55 -40 -40 0.8 0.56 5 +150 +125 +150 W W W C C C Conditions Min Max 45 -25 Unit V V
9. Thermal characteristics
Table 5: Symbol Rth(j-a) Thermal characteristics Parameter thermal resistance from junction to ambient SO8 TSSOP8 SO4 Rth(j-c) thermal resistance from junction to case in free air; SO4 only Conditions in free air; soldered in 155 220 100 25 K/W K/W K/W K/W Typ Unit
10. Characteristics
Table 6: Characteristics VP = 14.4 V; Tamb = 25 C; measured with test circuit of Figure 15; unless otherwise specified. Symbol VP Iq Parameter supply voltage quiescent current Conditions regulator operating VP = 4.5 V; IREG = 0 mA VP = 14.4 V; IREG = 0 mA 6 V VP 22 V; IREG = 10 mA 6 V VP 22 V; IREG = 50 mA
[1]
Min 3 -
Typ 14.4 10 15 0.2 1.4
Max 45 30 0.5 2.5
Unit V A A mA mA
Supply voltage
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
5 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
Table 6: Characteristics ...continued VP = 14.4 V; Tamb = 25 C; measured with test circuit of Figure 15; unless otherwise specified. Symbol VREG Parameter output voltage Conditions 8 V VP 22 V; IREG = 0.5 mA 6 V VP 45 V; IREG = 0.5 mA 0.5 mA IREG 100 mA 6 V VP 45 V VREG(drop) VREG(stab) VREG(line) dropout voltage VP = 4.5 V; IREG = 50 mA; Tamb 85 C output voltage long-term per 1000 h stability line regulation voltage 8 V VP 16 V; IREG = 0.5 mA 7 V VP 22 V; IREG = 0.5 mA 7 V VP 45 V; IREG = 0.5 mA VREG(load) load regulation voltage SVRR IREG(crl) ILO(rp) supply voltage ripple rejection current limit output leakage current at reverse polarity 0.5 mA IREG 50 mA fi = 120 Hz; Vi(ripple) = 1 V (RMS); IREG = 0.5 mA VREG > 4.5 V VP = -15 V; VREG = 0.3 V
[2]
Min 4.8 4.75 4.75 4.75 50 0.17 -
Typ 5.0 5.0 5.0 5.0 0.18 20 1 1 1 10 60 0.25 1
Max 5.2 5.25 5.25 5.25 0.3 10 30 50 50 -
Unit V V V V V mV mV mV mV mV dB A
Regulator output: pin REG
500
A
[1] [2]
The regulator output will follow VP if VP < VREG + VREG(drop) TDA3664TT: IREG 15 mA at Tamb 125 C; IREG 30 mA at Tamb 85 C.
11. Application information
11.1 Noise
The output noise is determined by the value of the output capacitor (see Table 7).
Table 7: Noise figures Noise figure (V)[1] C2 = 10 F 550 650
Measured at a bandwidth of 10 Hz to 100 kHz
Output current IO (mA) 0.5 50
[1]
C2 = 47 F 320 400
C2 = 100 F 300 400
11.2 Stability
For stable operation:
* The maximum output capacitor ESR should not exceed 22 (worst-case) and for the
minimum ESR, see Table 8.
* The ESR of the output capacitor is limited. * See Table 8 for the minimum ESR values of the output capacitor, at Tamb given the
load and output capacitance.
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
6 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
Remark: In the event of using different types of capacitors, a minimum ESR needs to be created by using an additional resistor that is placed in series with the output capacitor, see Figure 4.
* It is recommended not to use below 1 mA output current because of reduced phase
margin.
Table 8: 1 5 10 100 Minimum ESR values required C2 = 100 nF >0 >1 >0 >0 C2 = 1 F > 1.5 > 0.5 > 0.5 > 0.5 C2 = 10 F > 2.5 >1 >4 >4 C2 = 100 F >0 >0 >0 >0
IREG (mA) max
11.3 Application circuits
The maximum output current of the regulator equals: 150 - T amb 150 - T amb I REG ( max ) = --------------------------------------------------------- = ----------------------------------- ( mA ) 100 x ( V P - 5 ) R th ( j - a ) x ( V P - V REG ) When Tamb = 21 C, the maximum output current equals 140 mA at VP =14 V. The total thermal resistance of the TDA3664 (SOT223-1 package) can be decreased to lower values when pin 4 and body of the package are soldered to the printed-circuit board.
11.3.1 Application circuit with backup function
Sometimes, a backup function is needed to supply, for example, a microcontroller for a short period of time when the supply voltage spikes to 0 V (or even -1 V). This function can easily be built with the TDA3664 by using a large output capacitor. When the supply voltage is 0 V (or -1 V), only a small current will flow into pin REG from this large output capacitor (a few A). The application circuit is given in Figure 4.
VP
C1(1) 1 F
1
3
VREG(3)
TDA3664
2, 4
C2(2)
014aaa089
(1) C1 is optional (to minimize supply noise only) (2) C2 4700 F (3) VREG = 5 V (4) For reliable operation, it is recommended to have a minimum ESR of 3 of the output capacitor total (see Figure 4 above) and to have a stable application independent of load current, temperature or output capacitance.
Fig 4. Application circuit with backup function (SO4 version)
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
7 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
11.4 Additional application information
This section gives typical curves for various parameters measured on the TDA3664AT. Standard test conditions are: VP = 14.4 V; Tamb = 25 C .
mda947
25 Iq (A) 20
4 Iq (mA) 3
mda949
15 2 10
5
1
0 0 10 20 VP (V) 30
0 0 10 20 30 40 VP (V) 50
IREG = 0 mA
Fig 5. Quiescent current as a function of the supply voltage
mda948
Fig 6. Quiescent current increase at high supply voltage
mda950
0.48 Iq (mA)
2 Iq (mA)
0.44
1.8
0.40
1.6
0.36 5 10 15 20 VP (V) 25
1.4 5 10 15 20 VP (V) 25
IREG = 10 mA
IREG = 50 mA
Fig 7. Quiescent current as a function of the supply voltage.
Fig 8. Quiescent current as a function of the supply voltage
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
8 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
2 Iq (mA) 1.5
(1)
mda951
4 Iq (mA) 3
mda952
1
2
0.5
(2)
1
0 -40
0
40
80
120
160 Tj (C)
0 0 20 40 60 80 100 IREG (mA)
(1) Iq at 50 mA load (2) Iq at 10 mA load
Fig 9. Quiescent current as a function of the junction temperature.
mda955
Fig 10. Quiescent current as a function of the load current
mda957
6 VREG (V)
500
VREG(drop) (mV) 400
4
300
2 200
0 -50
0
50
100
150 Tj (C)
200
100 0 40 80 IREG (mA) 120
IREG = 0 mA
Fig 11. Output voltage thermal protection as a function of the junction temperature
Fig 12. Dropout voltage as a function of load current
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
9 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
6 VREG (V) 4
mda954
-30 SVRR (dB) -40
mda956
(1)
(2)
-50
(3)
2 -60
(1)
(2)
0 0 100 200 IREG (mA) 300
-70 10
(3)
102
103
104
f (Hz)
105
VP = 8 V; pulsed load.
CO = 10 F (1) SVRR at RL = 100 (2) SVRR at RL = 500 . (3) SVRR at RL = 10 k.
Fig 13. Foldback protection mode
Fig 14. Supply voltage ripple rejection as a function of the ripple frequency
12. Test information
VP
C1(1) 1 F
1
3
VREG(3)
TDA3664
2, 4
C2(2)
014aaa089
(1) C1 is optional (to minimize supply noise only) (2) C2 = 10 F (3) VREG = 5 V
Fig 15. Test circuit (SO4)
12.1 Quality information
The General Quality Specification for Integrated Circuits, SNW-FQ-611 is applicable.
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
10 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
13. Package outline
SO8: plastic small outline package; 8 leads; body width 3.9 mm SOT96-1
D
E
A X
c y HE vMA
Z 8 5
Q A2 A1 pin 1 index Lp 1 e bp 4 wM L detail X (A 3) A
0
2.5 scale
5 mm
DIMENSIONS (inch dimensions are derived from the original mm dimensions) UNIT mm inches Notes 1. Plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm (0.01 inch) maximum per side are not included. OUTLINE VERSION SOT96-1 REFERENCES IEC 076E03 JEDEC MS-012 JEITA EUROPEAN PROJECTION A max. 1.75 0.069 A1 0.25 0.10 A2 1.45 1.25 A3 0.25 0.01 bp 0.49 0.36 c 0.25 0.19 D (1) 5.0 4.8 0.20 0.19 E (2) 4.0 3.8 0.16 0.15 e 1.27 0.05 HE 6.2 5.8 L 1.05 Lp 1.0 0.4 Q 0.7 0.6 v 0.25 0.01 w 0.25 0.01 y 0.1 0.004 Z (1) 0.7 0.3 0.028 0.012
0.010 0.057 0.004 0.049
0.019 0.0100 0.014 0.0075
0.244 0.039 0.028 0.041 0.228 0.016 0.024
8o o 0
ISSUE DATE 99-12-27 03-02-18
Fig 16. Package outline SOT96-1 (SO8)
TDA3664_7 (c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
11 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
SO4: plastic small outline package; 4 leads; body width 3.5 mm
SOT223-1
D
E
A
X
c y
HE b1
vMA
4
Q A A2 A1 (A3)
1
Z e e1
2
bp
3
wM detail X
Lp L
0
2 scale
4 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.8 A1 0.10 0.02 A2 1.7 1.5 A3 0.25 bp 0.85 0.65 b1 3.15 2.95 c 0.35 0.25 D
(1)
E
(1)
e 2.3
e1 4.6
HE 7.3 6.7
L 1.75
Lp 1.02 0.62
Q 1.0 0.8
v 0.2
w 0.1
y 0.1
Z 1.2 0.7
10 0
6.7 6.3
3.7 3.3
Note 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. OUTLINE VERSION SOT223-1 REFERENCES IEC JEDEC TO-261 JEITA EUROPEAN PROJECTION
ISSUE DATE 99-12-15 03-02-19
Fig 17. Package outline SOT223-1 (SO4)
TDA3664_7 (c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
12 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
TSSOP8: plastic thin shrink small outline package; 8 leads; body width 3 mm
SOT505-1
D
E
A
X
c y HE vMA
Z
8
5
A2 pin 1 index
A1
(A3)
A
Lp L
1
e bp
4
detail X wM
0
2.5 scale
5 mm
DIMENSIONS (mm are the original dimensions) UNIT mm A max. 1.1 A1 0.15 0.05 A2 0.95 0.80 A3 0.25 bp 0.45 0.25 c 0.28 0.15 D(1) 3.1 2.9 E(2) 3.1 2.9 e 0.65 HE 5.1 4.7 L 0.94 Lp 0.7 0.4 v 0.1 w 0.1 y 0.1 Z(1) 0.70 0.35 6 0
Notes 1. Plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. Plastic or metal protrusions of 0.25 mm maximum per side are not included. OUTLINE VERSION SOT505-1 REFERENCES IEC JEDEC JEITA EUROPEAN PROJECTION ISSUE DATE 99-04-09 03-02-18
Fig 18. Package outline SOT505-1 (TSSOP8)
TDA3664_7 (c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
13 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
14. Revision history
Table 9: Revision history Release date 20070625 Data sheet status Product data sheet Change notice Doc. number Supersedes TDA3664_6 Document ID TDA3664_7 Modifications
* * * * *
The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. Legal texts have been adapted to the new company name where appropriate. Minor changes made to bulleted list in Section 11.2 Minor changes made to Table 8 Component additions to Figure 4 and Figure 15 Product data sheet Product specification 9397 750 15048 9397 750 07866 9397 750 07556 9397 750 06758 9397 750 06347 9397 750 04946 TDA3664_5 TDA3664_4 TDA3664_3 TDA3664_2 TDA3664_1 -
TDA3664_6 TDA3664_5 TDA3664_4 TDA3664_3 TDA3664_2 TDA3664_1
20050610 20001214 20001208 20000218 19990901 19990811
Preliminary specification Preliminary specification Preliminary specification Preliminary specification -
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
14 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
15. Legal information
15.1 Data sheet status
Document status[1][2] Objective [short] data sheet Preliminary [short] data sheet Product [short] data sheet
[1] [2] [3]
Product status[3] Development Qualification Production
Definition This document contains data from the objective specification for product development. This document contains data from the preliminary specification. This document contains the product specification.
Please consult the most recently issued document before initiating or completing a design. The term `short data sheet' is explained in section "Definitions". The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status information is available on the Internet at URL http://www.nxp.com.
15.2 Definitions
Draft -- The document is a draft version only. The content is still under internal review and subject to formal approval, which may result in modifications or additions. NXP Semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. Short data sheet -- A short data sheet is an extract from a full data sheet with the same product type number(s) and title. A short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. For detailed and full information see the relevant full data sheet, which is available on request via the local NXP Semiconductors sales office. In case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail.
malfunction of a NXP Semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. NXP Semiconductors accepts no liability for inclusion and/or use of NXP Semiconductors products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. Applications -- Applications that are described herein for any of these products are for illustrative purposes only. NXP Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Limiting values -- Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) may cause permanent damage to the device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the Characteristics sections of this document is not implied. Exposure to limiting values for extended periods may affect device reliability. Terms and conditions of sale -- NXP Semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms, including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by NXP Semiconductors. In case of any inconsistency or conflict between information in this document and such terms and conditions, the latter will prevail. No offer to sell or license -- Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights.
15.3 Disclaimers
General -- Information in this document is believed to be accurate and reliable. However, NXP Semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. Right to make changes -- NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. This document supersedes and replaces all information supplied prior to the publication hereof. Suitability for use -- NXP Semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or
15.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks are the property of their respective owners.
16. Contact information
For additional information, please visit: http://www.nxp.com For sales office addresses, send an email to: salesaddresses@nxp.com
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
15 of 16
NXP Semiconductors
TDA3664
Very low dropout voltage/quiescent current 5 V voltage regulator
17. Contents
1 2 3 4 5 6 6.1 6.2 7 8 9 10 11 11.1 11.2 11.3 11.3.1 11.4 12 12.1 13 14 15 15.1 15.2 15.3 15.4 16 17 General description . . . . . . . . . . . . . . . . . . . . . . 1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Quick reference data . . . . . . . . . . . . . . . . . . . . . 2 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pinning information . . . . . . . . . . . . . . . . . . . . . . 3 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 3 Functional description . . . . . . . . . . . . . . . . . . . 4 Limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5 Thermal characteristics. . . . . . . . . . . . . . . . . . . 5 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Application information. . . . . . . . . . . . . . . . . . . 6 Noise. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Stability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Application circuits . . . . . . . . . . . . . . . . . . . . . . 7 Application circuit with backup function . . . . . . 7 Additional application information . . . . . . . . . . . 8 Test information . . . . . . . . . . . . . . . . . . . . . . . . 10 Quality information . . . . . . . . . . . . . . . . . . . . . 10 Package outline . . . . . . . . . . . . . . . . . . . . . . . . 11 Revision history . . . . . . . . . . . . . . . . . . . . . . . . 14 Legal information. . . . . . . . . . . . . . . . . . . . . . . 15 Data sheet status . . . . . . . . . . . . . . . . . . . . . . 15 Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Contact information. . . . . . . . . . . . . . . . . . . . . 15 Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TDA3664_7
(c) NXP B.V. 2007. All rights reserved.
Product data sheet
Rev. 07 -- 25 June 2007
16 of 16

▲Up To Search▲

Price & Availability of TDA3664AT

	To Download TDA3664AT Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .