|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
V1.0 July 2009 TDA 5150 Multichannel / Multiband Transmitter M u l t i c h a n n e l / M u l t i b a n d R F T r a n s m i t t e r f o r 30 0 - 9 2 8 M H z b a n d s On-chip, high resolution fractional-N synthesizer and Sigma-Delta modulator with ASK, FSK, GFSK options Wireless Control Never stop thinking. Edition July 2009 Published by Infineon Technologies AG, Am Campeon 1 - 12 85579 Neubiberg, Germany (c) 2007 Infineon Technologies AG All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein. Information For further information on technology, delivery terms and conditions, and prices, please contact the nearest Infineon Technologies Office in Germany or the Infineon Technologies Companies and Infineon Technologies Representatives worldwide (www.infineon.com). Warnings Due to technical requirements, components may contain dangerous substances. For information on the types in question, please contact the nearest Infineon Technologies Office. Infineon Technologies Components may be used in life-support devices or systems only with the express written approval of Infineon Technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may be endangered. TDA 5150 Revision History: Previous Version: V0.94 issued January 2009 New issue V1.0 We Listen to Your Comments Is there any information in this document that you feel is wrong, unclear or missing? Your feedback will help us to continuously improve the quality of this document. Please send your proposal (including a reference to this document) to: wirelesscontrol@infineon.com TDA 5150 Table of Contents 1 1.1 1.2 1.3 1.4 1.5 1.5.1 1.5.2 1.5.3 1.5.4 1.5.5 1.5.6 1.5.7 2 2.1 2.2 2.3 2.4 2.4.1 2.4.2 2.4.2.1 2.4.2.2 2.4.2.3 2.4.3 2.4.3.1 2.4.3.2 2.4.3.3 2.4.3.4 2.4.3.5 2.4.4 2.4.4.1 2.4.4.2 2.4.5 2.4.5.1 2.4.5.2 2.4.5.3 2.4.6 2.4.6.1 2.4.6.2 2.4.6.3 2.4.6.4 2.4.6.5 Data Sheet Page Product Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Order Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Key Features overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Typical Application Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Sigma-Delta fractional-N PLL with High Resolution . . . . . . . . . . . . . . . . 8 Reduction of Spurs and Occupied Bandwidth . . . . . . . . . . . . . . . . . . . . . 9 Asynchronous and Synchronous Transmission . . . . . . . . . . . . . . . . . . . . 9 Integrated Data Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Fail-Safe Mechanism . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 TESEUS - Configuration and Evaluation Tool . . . . . . . . . . . . . . . . . . . . 11 TDA 5150 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PIN Configuration, Pin-out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pin Definition and Pin Functionality . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special Function Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Power Supply Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Brownout Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Low Battery Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SFRs related to Supply Voltage monitoring . . . . . . . . . . . . . . . . . . . . Digital Control (3-wire SPI Bus) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SPI XOR Checksum . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Command Byte Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transmit Command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Timing Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Data Encoder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PRBS9 Generator, Data Scrambler . . . . . . . . . . . . . . . . . . . . . . . . . . SFRs related to Transmitter Configuration and Data Encoding . . . . . Crystal Oscillator and Clock Divider . . . . . . . . . . . . . . . . . . . . . . . . . . . The Bit-Rate Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . The Clock Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . SFRs related to Crystal Oscillator and Clock Divide . . . . . . . . . . . . . Sigma-Delta fractional-N PLL Block . . . . . . . . . . . . . . . . . . . . . . . . . . . Fractional Spurs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Voltage Controlled Oscillator (VCO) . . . . . . . . . . . . . . . . . . . . . . . . . Loop Filter Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLL Dividers, RF Carrier Frequency . . . . . . . . . . . . . . . . . . . . . . . . . SFRs related to Sigma-Delta fractional-N PLL Block . . . . . . . . . . . . 4 12 12 12 17 18 18 18 19 20 21 21 21 23 24 25 26 28 29 31 32 33 33 35 35 36 36 37 38 38 V1.0, July 2009 TDA 5150 2.4.7 Digital FSK/GFSK Modulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.7.1 SFRs related to digital FSK / GFSK Modulator . . . . . . . . . . . . . . . . . 2.4.8 Power Amplifier, ASK Modulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.8.1 PA Output Power Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.8.2 ASK Modulation and ASK Sloping . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.8.3 Duty Cycle Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.8.4 Antenna Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.8.5 Fail-Safe PA Switch Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.8.6 SFRs related to RF Power Amplifier and ASK Modulator . . . . . . . . . 2.4.9 Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.9.1 SLEEP Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.9.2 STANDBY Mode (Data Retention Mode) . . . . . . . . . . . . . . . . . . . . . 2.4.9.3 TRANSMIT Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.9.4 XOSC_ENABLE Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.9.5 PLL_ENABLE Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.9.6 SFRs related to Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.10 Fail-Safe Mechanism and Status Register . . . . . . . . . . . . . . . . . . . . . . 2.4.10.1 Fail-Safe Flags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.10.2 Low Battery Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.10.3 SFRs related to Supply Voltage monitoring . . . . . . . . . . . . . . . . . . . . 2.4.11 RF Data Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.11.1 Asynchronous Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.11.2 Synchronous Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.11.3 Channel Hopping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4.11.4 SFRs related to Channel Hopping . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 Digital Control (SFR Registers) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5.1 SFR Register List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5.2 SFR Detailed Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 3.1 3.2 4 4.1 4.2 4.2.1 4.3 5 40 43 45 45 47 47 48 49 50 52 52 53 54 54 54 56 57 57 57 58 59 61 62 63 63 64 64 68 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Simple application schematics example . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Infineon Evaluation Board V1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 AC/DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 SPI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 Data Sheet 5 V1.0, July 2009 TDA 5150 Product Description 1 1.1 Product Description Overview The TDA 5150 is a low cost and easy to implement, multi-channel ASK/FSK/GFSK RF transmitter for the 300-320 MHz, 425-450 MHz, 863 - 928 MHz frequency bands with low power consumption and RF-output power of up to +10 dBm. The IC offers a high level of integration and needs only a few external components, such as a crystal, blocking capacitors and the necessary matching elements between the power amplifier output and the antenna. On-chip antenna tuning capacitors are implemented. An integrated high-resolution sigma-delta fractional-N PLL synthesizer covers all of the above listed frequency bands, using the same crystal for reference frequency generation. The configurable digital modulator allows precise FSK modulation and Gaussian shaping (GFSK), which contributes to reduction of occupied bandwidth. The output power of the integrated class-C RF power amplifier can be controlled over the SPI bus and if necessary, downsized (reduced) in digital steps. ASK shaping option contributes to reduced harmonics and minimized spectral splatter. The data encoder supports NRZ, Manchester, Bi-Phase, and Miller encoding. The device is fully configureable via the 3-wire Serial Peripheral Interface (SPI). 1.2 * * * * * * * * * * * * * * * Features High resolution Sigma-Delta fractional-N PLL synthesizer (frequency step size down to 7 Hz) Multiband/Multichannel capability for the 300-320 MHz, 425-450 MHz and 863-928 MHz bands Modulation types ASK (OOK) with ASK shaping, FSK (CPFSK) and GFSK Multi-channel and channel hopping capability, 4 register banks for fast Tx frequency switching Configurable via 3-wire serial interface bus (SPI) Manchester, Bi-Phase, and Miller encoding, on-chip PRBS9 scrambler Continuos checking of chip status by Fail-Safe mechanism Transparent and synchronized RF modulation mode Programmable clock divider output Configurable output power level from -10 dBm to +10 dbm, in 2 dB nominal steps Supply voltage range 1.9 V - 3.6 V, 2 low battery detection thresholds, preset to 2.4V and 2.1V Low supply current (Sleep Mode < 0.8 A, RF transmission 9 mA @ +5 dBm) ESD protection up to +/- 4 kV on all pins Operating temperature range -40C to +85C Green Package TSSOP-10 Data Sheet 6 V 1.0, July 2009 TDA 5150 Product Description 1.3 * * * * * * Applications Short range wireless data transmission Remote keyless entry transmitters Remote control units Wireless alarm systems Remote metering Garage door openers 1.4 Type TDA 5150 Order Information Ordering Code SP000300415 Package PG-TSSOP-10 1.5 1.5.1 Key Features overview Typical Application Circuit +VBAT C clocked by TDA 5150 SPI bus controlled by C VBAT SDIO SCK EN SDIO SCK EN CLKOUT XTAL GND C1 8.2 pF Q1 13.00 MHz VREG C2 100 nF C6 100 nF VBAT PAOUT L1 100 nH Antenna C XTAL / TIM / IRQ TDA 5150 GNDPA GND C3 10 pF* C4 5 pF* Remarks: * values valid for 433 MHz and the given antenna geometry Figure 1 Minimum component count application circuit The TDA 5150 application circuit shown demonstrates the ease and simplicity of an intelligent transmitter implementation. The C configures the TDA5150 via 3-wire SPI, the SDIO line is used at the same time to transfer data on SPI bus and as digital data input into the RF modulator. The CLKOUT line may be used as clock source for the C or as a timer for bitrate generation. Data Sheet 7 V 1.0, July 2009 TDA 5150 Product Description The matching shown is an example for a loop antenna application. Different antenna types (electrical monopole or dipole, magnetic loop etc.) as well as different layout versions might require component values which can differ from those given in above example. The antenna geometry has a major influence on the antenna impedance and consequently on the component values in the matching network. 1.5.2 Sigma-Delta fractional-N PLL with High Resolution This type of PLL offers a multitude of advantages compared to fixed, integer division ratio PLLs. In the reference oscillator circuit the same crystal can be used for all of the RF bands and frequencies (for example a 13 MHz crystal). Dedicated crystals for each frequency are no longer required. However by choice of crystal frequency a phenomenon, known as occurrence of fractional-N spurs must be kept in mind. The phenomenon and the countermeasures which should be taken to avoid it are described in detail in Chapter 2.4.6.1. The PLL allows a direct (G)FSK modulation for reduced spurs and harmonics with high accuracy and resolution compared to legacy transmitters using crystal pulling for FSK modulation. Synthesizer resolution down to 7 Hz for carrier frequency and FSK deviation allows fine tuning, correction of crystal tolerances and for temperature drift. Data Sheet 8 V 1.0, July 2009 TDA 5150 Product Description 1.5.3 Reduction of Spurs and Occupied Bandwidth The direct FSK modulation and in addition the Gaussian FSK (GFSK) reduces spurs and occupied bandwidth. Bandwidth reduction is exemplified below Figure 2 Spectrum of RF-signals with equal frequency deviations (+ 35kHz), same 20kBit/s datarate and encoding (NRZ). Blue plot corresponds to FSK modulation and green to GFSK. Observe the difference in terms of occupied bandwidth between the signals. 1.5.4 Asynchronous and Synchronous Transmission TDA 5150 offers a simple asynchronous transmission mode (transparent modulation), whereby after the configuration word is downloaded into the transmitter's SFRs (via SPI bus) the data bitstream is output on the SDIO line and fed into the transmitter's RF modulator. The CLKOUT signal can be used either as clock line for host C or, alternatively, as timer base (flag) for bitrate generator (this last function should be implemented in C). In this mode, the bitrate is solely imposed and controlled by the C software. GFSK modulation and ASK shaping options are allowed in Asynchronous Mode. In Synchronous Transmission Mode the bitrate is solely under the transmitter's control and fully timed by the TDA 5150. The CLKOUT is used to alert the C about the request for next databit. The C may have a higher allowable processing delay tolerance, typically the duration of 1/2 bit, before sending the corresponding bit via SDIO line to transmitter. Usage of data encoding option is allowed in Synchronous Mode. Data Sheet 9 V 1.0, July 2009 TDA 5150 Product Description 1.5.5 Integrated Data Encoder TDA 5150 comprises a Data Encoder which automatically generates encoded data from a regular (NRZ) bitstream. The supported data encoding modes are: * * * * * * * Manchester code Differential Manchester code Bi-phase space code Bi-phase mark code Miller code (Delay modulation) NRZ Scrambling (PRBS9 generator) All the encoded bitstreams can be level inverted (as part of the encoding option). The scrambling module (PRBS9 generator) is intended to be used for generation of pseudorandom data patterns (rather for Tx test scopes) or for basic level data encryption. 1.5.6 Fail-Safe Mechanism The Transmitter Status Register reports about failures such as: Brownout event, PLL lock error, VCO auto-calibration error and Register Parity error. The Register Parity is a special safety feature. Each SFR (Special Function Register) has an extra parity bit which is automatically calculated and stored during a SFR write operation. During transmitter active state these parity bits, belonging to SFR content are continuously recalculated and compared against the stored values. Changes in the contents of writable SFRs without write command generate an SFR error event and an error flag is set. To prevent erroneous transmissions (on wrong frequency or with erroneous modulation parameters, altered payload etc.) the activation of Fail-Safe mechanism is coupled with deactivation (switching off) of the RF Power Amplifier stages. This additional feature inhibits the transmission if errors occur, thus preventing the transmission of erroneous datagrams or on false frequency For details see the associated SFR description, and their interaction with the Fail-Safe Mechanism, as described in Chapter 2.4.10. Data Sheet 10 V 1.0, July 2009 TDA 5150 Product Description 1.5.7 TESEUS - Configuration and Evaluation Tool Figure 3 TESEUS - First Tab of User Interface screen TESEUS is a user-friendly, comfortable tool, suitable for generation of TDA 5150 configurations and testing them using a TDA 5150 Evaluation Board. Configurations can be automatically converted into register lists and implemented in C-code. The pattern to be transmitted is written into a datagram- or TX file. A commented example TX file can be generated by TESEUS. This file might be edited using a standard text file editor, if changes of the transmit parameters and data patterns are required. Note: for further details please consult the TESEUS User's Manual document. Data Sheet 11 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2 2.1 TDA 5150 Functional Description PIN Configuration, Pin-out EN 1 XTAL 2 GND 3 VREG 4 VBAT 5 10 9 SDIO / DATA SCK CLKOUT GNDPA PAOUT . TDA 5150 8 7 6 2.2 Pin Definition and Pin Functionality Pin Type Digital Input VBat Pin Name No. 1 EN Equivalent I/O Schematic Function Enable 3-wire bus 500 250k GNDD GNDD 2 XTAL Analog Input Crystal Oscillator VREG 0.9Vdc 600 XGND Bypass XGND Data Sheet 12 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description Pin Name No. 3 GND Pin Type Supply XGND Equivalent I/O Schematic Function Power supply ground GND Triple bond GNDD GNDA 4 VREG Analog Output VBAT Voltage Regulator Voltage Regulator output GNDD VREG VREG Double bond GNDD VDDA GNDA 5 VBAT Supply VBAT Voltage Regulator Power supply (+) VREG Data Sheet 13 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description Pin Name No. 6 PAOUT Pin Type RF-PA Output PAOUT 10 Equivalent I/O Schematic Function RF Power Amplifier Output (open drain) GNDPA GNDPA 7 GNDPA Analog GND GNDPA RF Power Amplifier Ground return Data Sheet 14 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description Pin Name No. 8 Pin Type Equivalent I/O Schematic Function CLKOUT Digital Output VBat 1.9 ... 3.6V VBat Programmable Divided Clock CLKOUT 500 GNDD GNDD Data Enable Data Core VBat 0 1 2k analog signals 7 GNDD Data Sheet 15 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description Pin Name No. 9 SCK Pin Type Digital Input VBat Equivalent I/O Schematic Function Clock 3-wire bus SCK 500 250k GNDD GNDD 10 SDIO Digital Input/ Output VBat 1.9 ... 3.6V VBat 500 Data Data 3-wire bus SDIO_DATA 250k Data Enable GNDD GNDD GNDD Data Sheet 16 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.3 Functional Block Diagram VREG VBAT Voltage Regulator Internal Supply EN SDIO SCK Digital Control Data Encoder / Fractional N PLL Digital ASK/FSK Modulator Power Amplifier Antenna Tuning PAOUT GNDPA XTAL Crystal Oscillator Clock Divider GND CLKOUT Figure 4 TDA 5150 Block Diagram TDA 5150 is an SPI configurable fully integrated ASK/FSK/GFSK RF transmitter for the 300-320 MHz, 425-450 MHz and 863-928 MHz frequency bands. The input datastream, applied to the digital SDIO line is transposed and appears as modulated RF-signal, at the output of the integrated RF power amplifier. Signal encoding and spectrum is in accordance with the chosen modulation type (i.e ASK, FSK or GFSK) and encoding scheme. TDA 5150 contains following major blocks which extend the functionality compared to legacy RF transmitters: * An on-chip voltage regulator is delivering 2.1 V nominal supply voltage for the transmitter's functional units. In addition, the battery voltage is monitored and battery low and brown out flags are set, if a critical supply voltage drop event occurs. For avoidance of erroneous transmissions, the brownout flag is coupled with the RF Power Amplifier state control. If a brownout or critical voltage drop event occurs, the RF Power Amplifier is automatically switched off, as part of the Fail-Safe philosophy. The mechanism is explained in detail in Chapter 2.4.8.5 The crystal oscillator and the associated clock divider(s) generate the required clock signals. There is an output line (CLKOUT) which may be used to clock a host C, or for bit rate generation. A digital control logic, accessible for user via the SPI bus allows flexible and fast (re)configuration. At the same time it offers a simple but powerful Fail-Safe mechanism, which enhances the reliability of transmissions 17 V 1.0, July 2009 * * * Data Sheet TDA 5150 TDA 5150 Functional Description * The data encoder synchronizes the bitstream to be transmitted with the internal bit clock. It supports different types of Manchester and Bi-Phase encodings and is able to generate PRBS9 pseudo-random patterns. The internal data encoder can be bypassed, allowing transmissions in direct (transparent) mode. The core element of the transmitter is the sigma-delta fractional-N PLL Synthesizer, used for carrier frequency control and as part of the digital modulator as well. It covers the frequency bands 300-320 MHz, 425-450 MHz and 863-928 MHz with outstanding frequency resolution. Only one, fixed frequency crystal (e.g. 13 MHz) is required for reference frequency generation. The synthesizer is characterized by short settling time. It is also used as direct FSK modulator, and together with a Gaussian filter, implemented by means of lookup table offers the functionality of a direct GFSK modulator. The integrated Power Amplifier is able to deliver up to +10dBm output power into a 50 load (usually the antenna) via an external impedance matching network. In addition there are integrated capacitors, connected between GND and the RF-PA output, over SFR controlled on/off switches. These capacitors are elements of a software controlled antenna tuner. They may be used to fine-tune (adjust) the PAoutput to Load matching network impedance, and thus to maintain good VSWR values over a wider frequency band. This is particularly useful if the transmitter is operated not only on a single frequency but in a given frequency band. * * 2.4 2.4.1 Functional Description Special Function Registers TDA 5150 is configurable by programming the Special Function Register bank (abbreviated SFRs) via the SPI interface. Terminology and notations related to TDA5150 SFR set, list of symbols and programming restrictions are given in Chapter 22 Register Terminology. Detailed description of SFR map, programming, usage and content explanations are found in the following chapters (2.4.x.x and 2.5.x.x). See also Chapter 2.5.1 SFR Register List. 2.4.2 Power Supply Circuit An internal voltage regulator generates a constant supply voltage (2.1V nominal) for most of the analog and digital blocks. An external capacitor (100nF nominal value) connected between VREG (pin 4) and GND (pin 3) is necessary to guarantee stable functionality of the regulator. The regulated voltage on VREG pin is not adjustable by user and it is not allowed to connect any additional, external loads to this pin, but the above mentioned decoupling capacitor. Data Sheet 18 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description In STANDBY state, a special, low-power voltage regulator is activated, which is supplying only the SPI bus interface, the SFR registers and the system controller. In order to further reduce the current consumption, and keeping in mind that leakage currents can steeply increase by high temperatures, an additional low-power state, denoted SLEEP was defined. In this state most of the digital part is disconnected from the regulator (VREG). Only the SPI bus interface remains active. As a consequence, further power saving is achieved, but register content is lost by entering this mode. See Chapter 2.4.9 Operating Modes for further informations. 2.4.2.1 Brownout Detector A Brownout Detector (abbreviated BOD) is integrated into the TDA 5150 transmitter. Brownout is a condition where the supply voltage drops below a certain threshold level. By brownout events the integrity of SFRs can not be guaranteed, even if the dropout's duration is very short. During active states, BOD monitors the VREG pin; during STANDBY, it monitors VBAT and VREG supply lines. Table 1 BOD Thresholds Description Brownout Detection Level--Active State Brownout Detection Level--StandBy State VBDR VPDBR Monitored @ VREG VREG & VBAT min max 1.7 V 1.8 V 0.7 V 1.7 V If the BOD detects a brownout, the Power Amplifier is switched off and the SFRs are reset. The device is then forced to restart from the Power Up Reset condition. This ensures that the device is always in a well-defined logic state. V VREG V THR POR =V BRD RESETN t POR t POR t POR 0.25..10 ms 0.25..10 ms 0.25..10 ms Figure 5 Power-on Reset/Brownout Detector Data Sheet 19 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description Brownout is indicated by bit BROUTERR (0x01.2) within SFR TXTSTAT (0x01). Note: The BOD itself can not be used to guarantee the correct operation of analog sections, where the minimum operating voltage is defined to be 1.9 V; as this is larger than the maximum BOD voltage. In other words, in case of a supply voltage drop, the voltage region which is critical for reliable operation of the analog sections (min 1.9V) is reached before the brownout detector triggers (between 1.8..1.7V). See also Chapter 4.2 for operating voltage limits. 2.4.2.2 Low Battery Detector TDA 5150 has an embedded Low Battery Detector (LBD) block. In active modes, LBD monitors the voltage on VBAT supply line (pin 5). LBD has two activation thresholds, set to 2.4 V and 2.1 V. The status regarding supply voltage below threshold events can be updated by reading from SFR TXSTAT, bits 4 and 5 (0x01.5:4). These LBD flags are cleared after every transmission start. The LBD might be used as early warning for low battery voltage state (but before the battery voltage is dropping below the critical value, which renders normal operation capability). Data Sheet 20 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.2.3 SFRs related to Supply Voltage monitoring TXSTAT--Transmitter Status Register Bit 6 n.u. ADDR 0x01 Bit 7 1 Bit 5 LBD_2V1 Bit 4 LBD_2V4 Bit 3 c/0 Bit 2 c/1 Bit 1 PARERR Bit 0 PLLLDER VAC_FAIL BROUTERR / Bit 7 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 LBD_2V1 LBD_2V4 BROUTERR PARERR PLLLDERR 1 / r/0 r/0 c/0 c/0 Set to 1, mandatory battery low detected, threshold at 2.1 V battery low detected, threshold at 2.4 V Don't care Brown out event Parity error PLL lock detector error LBD_2V1 LBD_2V4 reserved BROUTERR PARERR PLLLDER Battery voltage drop below 2.1 V detected if 1 - in standby mode, bit is invalid Battery voltage drop below 2.4 V detected if 1 - in standby mode, bit is invalid Brownout event detected if 1 Parity error detected if 1 PLL lock error detected if 1 2.4.3 Digital Control (3-wire SPI Bus) The control interface is a 3-wire Serial Peripheral Interface (SPI), which is used for device control and data transmission. 2.4.3.1 * SPI Pin Description * EN - enable input with embedded pull-down resistor. High level on EN input enables the SPI transmission. The rising edge of the EN signal triggers the selection of the active SCK edge (for the consequent data transfer, until the EN line goes again in low state) and transmission/ sampling of data between the device and the microcontroller can start. For details refer to Figure 6 and Figure 7. SDIO - 3-state input/output This bidirectional line is used for data transfer between the TDA 5150 and external host (usually a C). On-chip pull-down resistor is connected to this pin Data Sheet 21 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description * SCK - clock input pin with embedded pull-down resistor. If SCK is at low level while EN goes high, the incoming SDIO data is sampled by falling edge of the SCK and the output SDIO data is set by the rising edge of SCK. Contrariwise, If SCK is at high level when EN goes high, the SDIO data is sampled with the rising edge of the SCK clock and output on SDIO by falling edge of the SCK clock. For details refer to Figure 6 and Figure 7. SPI commands are started by the rising edge on the EN line and terminated by the falling edge on EN. The available Burst Write mode allows configuration of several SFRs within one block access, without cycling the EN line Low - High - Low for each individual byte. By keeping the EN line at High level, subsequent bytes could be sent, and the byte address counter is autoincremented, thus speeding up the transfer on the SPI bus. A self-explaining diagram is found here: Chapter 9 Timing Diagrams of 3-wire SPI. The active edge of SCK (during SPI commands) is programmable, and it is determined by the level on SCK line at the moment of activation of the EN line (rising edge on EN). If SCK is low at that moment, the incoming SDIO data will be sampled with the falling edge of SCK, and output by rising edge of SCK (see Figure 6 below).. tDS EN tEN SCK SCK level sampled tSSu t CH tSHo tNEN Output (write SDIO) SDIO Sample (read SDIO) tCL tIDSu tIDHo Figure 6 SPI Timing -- SCK low at rising edge of EN If SCK is high during occurrence of rising edge on EN, incoming SDIO data is sampled with the rising edge on SCK, and output by falling edge of SCK, as illustrated in Figure 7. Data Sheet 22 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description t DS EN tEN SCK t IDSu SDIO Sample (read SDIO) SCK level sampled t SSu tCH tSHo tNEN tIDHo Output (write SDIO ) t CL Figure 7 SPI Timing -- SCK high at rising edge of EN 2.4.3.2 SPI XOR Checksum The SPI block includes a safety feature for checksum calculation. This is achieved by means of XOR operation between the address and the data during write operation of SFR registers. The checksum is in fact the XOR of the data 8-bitwise after every 8 bits of the SPI write command. The calculated checksum value is then automatically written into SFR SPICHKSUM (0x00) and can be compared with the expected value.By executing a read operation of SFR SPICHKSUM (0x00) the register content is automatically cleared (after read). Read access to any of the other readable SFRs does not influence the SFR SPICHKSUM. enable every 8 bit SPI shift register XOR Checksum SFR read/clear Figure 8 Example: Generating the Checksum of SFRs, block diagram Write to SFR address 0x04, data 0x02, address 0x05, data 0x01 Bytes transmitted via SPI 0000 0100 0000 0010 0000 0101 0000 0001 Result in Checksum Register 0000 0100 0000 0110 0000 0011 0000 0010 After writing into the registers, content of checksum SFR SPICHKSUM (0x00) will be 0x02. Data Sheet 23 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.3.3 Command Byte Structure First byte of each SPI sequence is the Command Byte, with the following structure: Function Code C1 x C0 x A5 A4 Command Byte Configuration Address A3 A2 A1 A0 The first 2 bits C1, C0 of the Command Byte are the function code field. They define the command to be performed, according to the following table: C1 0 C0 0 Function Code Configuration Bits Write data into SFR register 0 1 1 1 0 1 The Write / Read Command bytes are used for device control. Bit fields Data Sheet 24 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.3.4 Transmit Command The Transmit Command Byte is used for data transmission. It precedes the datagram to be transmitted. The Transmit Command Byte format is described in the following table: C1 1 C0 Bit 1 A Transmit Command Configuration Function Data sync Value, description 0: off 1: on (at the same time Bit C - Encoding must be set also to 1 -->int. Encoding) 0: PA off at the falling edge of EN (synchronized with bit-rate if bit A is high) 1: SDIO/DATA is latched at the falling edge of EN, PA stays on, TX data are kept constant. After the time-out of 65536 / fsys which is ~5 ms for a 13 MHz crystal, PA and PLL are switched off. 0: off 1: on (selects SFR register for encoding Bit A must be also set to1 -->Data sync) 1 1 B PA mode 1 1 C Encoding 1 1 1 1 D Pwr. level/ 0: selects PowerLevel/Modulation Setting1 ModSetting 1: selects Power Level/Modulation Setting2 Frequency 0 (00): selects frequency channel A selection 1 (01): selects frequency channel B 2 (10): selects frequency channel C 3 (11): selects frequency channel D (for description of frequency channels A..D programming see Chapter 2.4.11.3 Channel Hopping) Note: After the last configuration bit for a new transmission was sent, a break of at least 100 s must be provided in order to achieve PLL settling and lock on the selected channel frequency. Data Sheet 25 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.3.5 Timing Diagrams In the following timing diagrams the 4 possible SPI commands are shown. The examples are valid for the case of SCK is low when EN line goes from Low into High (rising edge). Therefore the incoming SDIO data is sampled at the falling edge of SCK, and data is output on SDIO line by the rising edge of SCK signal. WRITE SFR: EN 7 0 7 0 SCK Command Address Data Byte SDIO 0 0 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 READ SFR: EN 7 0 7 0 SCK Command Address Data Byte SDIO 0 1 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 BURST write SFR: EN 7 0 7 0 7 0 7 0 SCK Command Address Data Byte 0 Data Byte 1 Data Byte N SDIO 0 0 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 TRANSMIT data: EN > 1000us if TX issued from STDBY else determined by SCK speed > 100us 7 0 SCK Command Configuration Data to transmit SDIO 1 1 A B C D E F d1 d2 d3 d4 d5 Figure 9 Timing Diagrams of 3-wire SPI Data Sheet 26 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description Note: In order to minimize cross-talk between SDIO and SCK lines, it is recommended to keep the SCK either Low or High, but avoid transitions during RF transmission. Previous Chapter 2.4.3.4 Transmit Command gives an in-depth overview of Transmit Command structure. Data Sheet 27 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.4 Data Encoder The Data Encoder is used in the so-called Synchronous Transmission Mode. A description of this transmission mode is found in Chapter 2.4.11.2 Synchronous Transmission. In Synchronous Transmission Mode the Encoder has to be used. If no specific encoding of SDIO data shall be done, select NRZ as encoding scheme. Definition: bit-rate is the number of transmitted bits per second and expressed in [bits/sec]. Besides NRZ all the other implemented encoding methods split a single bit into two elementary parts, the so-called chips. Therefore we also talk about a chip-rate, which is an "n" multiple of the data-rate. For NRZ (which means no extra encoding) n =1 (data-rate = chip-rate), and for all other implemented encoding methods n = 2, or the chip-rate is twice the bit-rate. The TDA 5150 supports the following encoding types: * * * * * * * Manchester code Differential Manchester code Bi-phase space code Bi-phase mark code Miller code (Delay modulation) NRZ Scrambling (PRBS9 generator) Data Clock NRZ Manchester Differential Manchester Biphase Space Biphase Mark Miller 1 0 1 0 0 1 1 0 All encoded bitstreams can be level inverted (as part of the encoding option) PRBS Scrambling Figure 10 Data Sheet Coding Schemes 28 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description The Data Encoder option is enabled by bit C of Transmit Command (Data Encoder enabled if bit C=1). See also Chapter 2.4.3.4 Transmit Command for command structure. If the Data Encoder is enabled, bit A must to be set for Synchronous Transmission Mode as well (Bit A=1 and Bit C=1, this last to enable encoding). The selection of encoding mode is done via bits ENCODE (0x05.2:0) of SFR TXCFG1. (0x05). At the same time bit INVERT (0x05.3) of the same SFR enables the inversion of an already encoded bit stream. The encoding activation entry point can be configured in SFR ENCCNT (0x27). By initializing the SFR ENCCNT (0x27) with 0x00, already the first bit is encoded. If for example ENCCNT = 0x10, the first 16 bits should remain unencoded. This method allows to keep the first N bits unencoded within a datagram (in fact plain NRZ), followed by encoded bits (of the same datagram).The encoding scheme is selected by bit-field ENCMODE (0x05.2:0) of SFR TXCFG1. 2.4.4.1 PRBS9 Generator, Data Scrambler TDA 5150 contains a PRBS9 generator, suitable for generation of pseudo-random NRZ data patterns.The PRBS9 datastream satisfies (in general lines) the requirements for random distribution (even if longer PRBS polynomials come closer to "true" random distribution) and therefore it can be useful for Transmitter RF tests, for instance by measurement of the "Occupied RF Bandwidth". In addition the generated PRBS9 pattern can be XOR'ed with a real data pattern sent by the microcontroller and this way "scramble" this data pattern. Attention: The data scrambling functionality is intended to enhance the clock recovery performance of the Receiver Station. It is not suitable, as stand-alone encryption method for security applications! PRBS9 is a well known standard in the class of pseudo-random patterns, and is implemented within the TDA 5150 by a subpart with following block diagram: PRBS Start value loaded @ start of TX 7 6 5 4 3 2 1 0 BDR CLK D D D D D D D D to modulator SDIO D Figure 11 PRBS9 Generator and Data Scrambler Data Sheet 29 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description The feedback branches within the PRBS9 generator are fixed (as shown above), but the PRBS generation can be influenced by SFR configuration in the following manner: * A start value for the PRBS9 Generator can be programmed in SFR PRBS Start Value (0x08). The reset value is 0xAB (10101011). Choice of 0x00 as start value is not allowed, because the output of PRBS9 Generator should "lock" and will never go in High. The PRBS Start Value is loaded into the PRBS9 Generator at the start of each transmission. If the Data Scrambler is used, the start of scrambling can be configured in SFR ENCCNT (0x27). If ENCCNT is 0, already the first bit is XOR'ed with PRBS9. If for example ENCCNT = 0x10, the first 16 bits stay unscrambled. This is necessary if a data frame should have always the same wake up and synchronization part, but the payload should be pseudo-random for sensitivity measurements or to enhance the clock recovery on the receiver side. * Data Sheet 30 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.4.2 SFRs related to Transmitter Configuration and Data Encoding ADDR 0x05 Bit 7 GO2SLEEP TXCFG1--Transmitter Configuration Register 1 Bit 6 Bit 5 ASKFSK1 Bit 4 ASKSLOPE Bit 3 INVERT Bit 2 w/1 Bit 1 w/0 Bit 0 w/1 ASKFSK2 ENCMODE ENCMODE ENCMODE cw/0 Bit 3 w/0 INVERT w/1 w/0 w/0 Data inversion Bit <2:0> ENCMODE INVERT ENCMODE Encoding mode bit <2:0> Encoded data inversion enable 0: data not inverted Encoding mode, code selection (3 bits) 000: 010: Manchester Biphase Space 001: 011: Differential Biphase Manchester Mark 100: Miller (Delay) 101: NRZ 110: Scrambling (PRBS) 111: not used (data =0) 1: data inverted ADDR 0x08 Bit 7 PRBS PRBS--PRBS Start Value Bit 6 PRBS Bit 5 PRBS Bit 4 PRBS Bit 3 PRBS Bit 2 PRBS Bit 1 PRBS Bit 0 PRBS w/1 w/0 w/1 w/0 w/1 w/0 w/1 w/1 Bit <7:0> PRBS PRBS PRBS start value bit <7:0> PRBS start value (8 bits), the PRBS generator uses this value as a starting value after each transmission beginning Data Sheet 31 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x27 Bit 7 ENCCNT ENCCNT - Encoding start bit counter Bit 6 Bit 5 ENCCNT Bit 4 ENCCNT Bit 3 ENCCNT Bit 2 ENCCNT Bit 1 ENCCNT Bit 0 ENCCNT ENCCNT w/0 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:0> ENCCNT ENCCNT Encoding start bit counter bit <7:0> Sets the number of bits on start of a telegram which shall be sent unencoded or unscrambled before encoder/scrambler is switched on. This feature is used e.g. for send of unscrambled synchronization patterns first, followed by encoded payload. 2.4.5 Crystal Oscillator and Clock Divider The Crystal Oscillator is a single pin, negative-impedance-converter type oscillator (NIC), and provides the reference frequency for the phase locked loop and clock signal for the sigma delta modulator. Figure 12 Oscillator Circuit The allowed crystal frequencies are in [12..14] MHz range. A load capacitor (C1) is connected in series with the crystal. The value of the load capacitor depends on crystal parameters and - at some extent even the parasitic capacitance of the PCB layout has a slight, but measurable influence. The shown values are exemplifications, and valid for the crystal used on IFX evaluation board. Please refer also to the crystal oscillator parameters listed in Chapter 4 Electrical Characteristics to select a suitable crystal type. Theoretically any crystal frequency, within the frequency range specified above, can be used. In practice this freedom is limited by the occurrence of so-called Fractional Spurs. (See also Chapter 2.4.6.1 Fractional Spurs for details). To avoid this unwanted effect, Data Sheet 32 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description the crystal frequency must be chosen in such way, that the division ratio: PLL division factor = (RF carrier frequency) / (crystal frequency) gives a fractional part (the part behind the decimal point) between 0.1 and 0.9. For example a 13.56MHz crystal should not be used for 868MHz (resulting PLL division factor is 64.012 and the fractional part, equaling 0.012 is smaller then 0.1). In addition the RF frequencies used for the FSK deviation must not cross the PLL division factor integer line (lower and higher FSK frequencies have different PLL division factors). This criterion is automatically fulfilled if and when the rule, stated above for the fractional part is fulfilled. 2.4.5.1 The Bit-Rate Generator The TDA 5150 is able to generate a bit (or chip) clock by dividing the signal frequency output by the crystal oscillator. /16 SDIO @ PWRUP Divide by 1/2/4/8/16/ 32/64/128 Clock Divide by 1 to 256 BDRDIV counter Divide by 2 50:50 Divide by 1/2/4/8 Afterscaler CLK SW 1 CLK output SW 2 XTAL Prescaler Bitrate clock CLKSRC Figure 13 Bit-Rate Divider In Asynchronous Transmission Mode the bitrate clock can be routed to CLKOUT pin and used by the C as timer signal for bitrate generation. In Synchronous Transmission Mode the bitrate clock is in addition used internally, for synchronization of the incoming bitstream. The bitrate or chiprate is calculated according to the formula: f XOSC bitrate = ----------------------------------------------------------------------------------------------------------------------------------PRESCALE x ( BDRDIV + 1 ) x 2 x A FTERSCALE 2.4.5.2 The Clock Output The TDA 5150 offers a clock output signal (CLKOUT), derived from the crystal frequency. It can be used as source for system clock of a C or as bit (chip) clock to control the data rate as already described. Different stages of the bit-rate divider can be routed to CLKOUT, as well as the output of the XTAL / 16 divider according to following rules: * If SDIO = 0 when EN goes High, the output clock chosen as XTAL/16 by default. 33 V 1.0, July 2009 Data Sheet AFTERSCALE PRESCALE BDRDIV TDA 5150 TDA 5150 Functional Description * If SDIO = 1 when EN goes High, the output clock is selected as imposed by settings of SFR CLKOUTCFG (0x06). This is the configurator register for Clock pre- and afterscaler. Detailed description of the bit-fields is given in next Chapter 2.4.5.3 SFRs related to Crystal Oscillator and Clock Divide If enabled, the CLKOUT starts toggling when the swing amplitude on crystal oscillator output reaches a certain threshold. If disabled, no clock signal is output on CLKOUT, but it delivers a rising edge pulse and stays high, signalizing that the crystal oscillator output already reached a stable level Note: If the CLKOUT line is used as system clock for a C, keep in mind that in Synchronous Transmission Mode the delivered frequency is not highly stable in phase (it is affected by jitter), due to the fact that the related counters are synchronized with each Transmit Command. The reasons for it and the synchronization procedure itself are explained in Chapter 2.4.11.2 Synchronous Transmission. Data Sheet 34 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.5.3 r SFRs related to Crystal Oscillator and Clock Divide ADDR 0x06 Bit 7 CLKSRC CLKOUTCFG - Clock Pre- and Post-scaler Bit 6 Bit 5 w/0 Bit 4 w/0 Bit 3 PRESCALE Bit 2 PRESCALE Bit 1 PRESCALE Bit 0 CLKOUTENA CLKSRC AFTERSCAlE AFTERSCALE w/0 w/0 w/1 w/0 w/0 w/1 Bit <7:6> CLKSRC Bit <5:4> AFTERSCALE Bit <3:1> PRESCALE Bit 0 CLKOUTENA Clock source selection bit <1:0> 00: after prescaler, 01: after BRDIV counter 10: after BRDIV counter inverted, 11: after afterscaler Afterscaler selection bit <1:0> divide by 2^AFTERSCALE Prescaler selection bit <2:0> divide by 2^PRESCALE 0 if CLKOUT disabled. In this case CLKOUT goes High after crystal oscillator achieves stable level 1 if clock output enabled ADDR 0x07 Bit 7 BDRDIV BDRDIV--Bit-rate Divider Bit 6 Bit 5 BDRDIV Bit 4 BDRDIV Bit 3 BDRDIV Bit 2 BDRDIV Bit 1 BDRDIV Bit 0 BDRDIV BDRDIV w/1 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:0> BDRDIV BDRDIV divider bit <7:0> 2.4.6 Sigma-Delta fractional-N PLL Block The Sigma-Delta fractional-N PLL contained on-chip is the core piece of the transmitter. The advantage of a fractional-N PLL is that not only integer multiples of the crystal frequencies [N * fXTAL] can be generated, but also values of N-multiples plus a fractional part. Part of the PLL is a VCO (Voltage Controlled Oscillator) running at a center frequency of approximately 1.8 GHz. The VCO frequency is divided at first by 2 in a prescaler block with fixed division ratio. It is then further divided by 1, 2 or 3 in the band select divider block, the resulting frequency equaling the transmitter's RF output frequency. Data Sheet 35 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description This RF signal is then further divided in a multimodulus divider block down to a frequency which is in same range as those of the reference signal's, input from the reference oscillator (i.e the crystal oscillator). The reference oscillator's frequency and the VCO's subdivided frequency, input from multimodulus divider are compared in a phase detector. On the output of the phase detector an error signal, proportional to the phase difference of the two, above mentioned signals is obtained. The phase-error signal is converted to a bipolar current by the charge pump and then fed into the loop filter (integrator). The output of this integrator controls the VCO frequency via the tuning voltage and so closing the loop. The multimodulus divider is able to switch between different dividing factors. Thus it is possible e.g. to divide by 2.5 by first dividing by 2, than by 3, followed by 2 again, and so on. The dividing factor is defined by the Sigma-Delta Modulator. 2.4.6.1 Fractional Spurs Due to the behavior of Sigma-Delta PLLs, spurs are generated at frequencies close to the integer multiples of the reference frequency. These spurs are named Fractional Spurs. It is therefore recommended to use PLL division ratios (output RF frequency divided by crystal oscillator frequency) with fractional parts between 0.1 and 0.9, or in other words, the crystal frequency should be chosen in such way to yield for fractional part of the PLL division ratio values between 0.1 and 0.9. 2.4.6.2 Voltage Controlled Oscillator (VCO) The Voltage Controlled Oscillator runs at approximately 1.8 GHz. This is 2, 4, or 6 times the desired RF output frequency, dependent on the frequency band settings. To trim out production tolerances of the VCO, a VCO Auto Calibration mechanism (VAC) is implemented and runs automatically during each start up of the PLL. First a fixed, internal voltage is applied to the VCO, and the generated RF frequency is divided by 4 (or 8 for 868/915 MHz bands). The positive transitions are then counted during 32 system clock cycles. The result is compared to a configured number, derived from the desired RF frequency value (as the formula shows). The VCO is then automatically finetuned, before an RF transmission starts. PLLFRAC<20:0>+0.5 PLLINT<6:0> + ---------------------------------------------------------21 2 - 0.5 VAC_CTR<8:0> = ------------------------------------------------------------------------------------------------------- x VAC_NXOSC<5:0> ( ISMB<1> + 1 ) x 4 where: * VAC_CTR<8:0> has to be calculated according the formula above. It contains the optimal number of positive transitions to which the VAC-counter result is compared. 36 V 1.0, July 2009 Data Sheet TDA 5150 TDA 5150 Functional Description * * * PLLINT <6:0> and PLLFRAC <20:0> PLL divider SFRs used to define the desired RF frequency. ISMB<1> MSB of SFR register ISMB<1:0>, for band selection. VAC_NXOSC<5:0> always set to 32 decimal or 0x20, number of elapsed system clocks time (duration) used for VAC counting. 2.4.6.3 Loop Filter Bandwidth In order to provide a high grade of flexibility by choice of modulation parameters, a PLL with programable bandwidth have been implemented in the TDA5150. The damping resistor(s), part of the active Loop Filter in PLL can be selected by means of a 3 bit control field designated PLLBWTRIM in the SFR register PLLBW (0x25.6:4). Aiming the minima of RF-energy leaking into the adjacent channel(s) and/or out of band transmissions, the PLL bandwidth should be set as narrow as possible, but not less then 1.5.. 2 times the chip rate, if FSK or GFSK modulation is used. For NRZ encoding the chip rate and data- or bit rate are the same. For all other coding schemes like Manchester or Bi-Phase etc. each bit is represented by two chips. Therefore the chip rate is the double of the bit rate for all encoding schemes, implemented in the TDA5150 encoder, excepting NRZ. The chip rate is not influenced by the fact whether the encoding is done by the on-chip Data Encoder or is realized externally. In order to maintain loop stability within the PLL and for optimum performance, following chargepump settings should be used, correlated with loop filter damping: Table 2 PLL recommended settings Chargepump settings and resulting current CPTRIM Bit3 * 1 1 1 0 0 0 0 Bit2 * 1 1 0 1 1 0 0 Bit1 * 1 0 0 1 0 1 0 Bit0 * 1 0 1 0 0 0 1 CP_current [uA] * 40 32.5 25 17.5 12.5 7.5 5 * 410 375 335 270 230 175 150 Loop filter damping resistor selection PLLBW TRIM Bit2 0 0 0 0 1 1 1 1 Bit1 0 0 1 1 0 0 1 1 Bit0 0 1 0 1 0 1 0 1 Resulting nominal PLL BW [kHz] Notes not recommended Data Sheet 37 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.6.4 PLL Dividers, RF Carrier Frequency The divider chain contains a fixed divider by 2 (prescaler), a band select divider, dividing by 1 for the 915 and 868 MHz bands, by 2 for the 434 MHz band, and by 3 for the 315 MHz band. The divider ratio of this block is controlled by the field SMB0/1 of SFR TXCFG0 (0x04.3:2).This band selection block is followed by the Multi-Modulus Divider, which is controlled by the Sigma-Delta Modulator. The RF frequency is set in the PLL Integer and PLL Fractional SFRs. Up to 4 different frequencies may be preconfigured in the same band (Frequency Registers A, B, C, D) and finally the active channel selected through the Transmit Command. This allows fast channel switching or hopping, without the need of downloading the complete reconfiguration dataset into the corresponding SFRs (i.e the new PLL settings). The RF frequency fRF is derived from the crystal frequency. PLLFRAC< 20:0 > + 0.5 f RF = f XOSC x PLLINT< 6:0 > + --------------------------------------------------------------- 21 2 - 0.5 For the 315 MHz and 433 MHz bands (ISMB<1> = 0) PLLINT bit 6 is not used and only values from 15 to 43 are valid. For the 868 MHz and 915 MHz bands (ISMB<1> = 1) all PLLINT bits are used and values between 54 and 84 are valid. 2.4.6.5 SFRs related to Sigma-Delta fractional-N PLL Block ADDR 0x04 Bit 7 GO2STDBY TXCFG0--Transmitter Configuration Register 0 Bit 6 Bit 5 reserved Bit 4 FSOFF Bit 3 ISMB Bit 2 ISMB Bit 1 reserved Bit 0 reserved reserved cw/0 Bit 7 Bit 6 Bit <3:2> ISMB w/0 GO2STDBY FSOFF ISMB w/0 1: activate STANDBY 1: activate FAILSAFE w/0 w/0 w/1 w/1 w/0 RF frequency band bits ISM band selection (2-bits) 00: MHz 300-320 01: MHz 425-450 10: MHz 863-870 11: MHz 902-928 Data Sheet 38 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x09, 0x0D, PLLINTn--PLL MM Integer Value Channel A, B, C, D 0x11, 0x15 n: Channel A, B, C, D Bit 7 n.u. Bit 6 PLLINTn Bit 5 PLLINTn Bit 4 PLLINTn Bit 3 PLLINTn Bit 2 PLLINTn Bit 1 PLLINTn Bit 0 PLLINTn / w/1 w/0 w/0 w/0 w/0 w/0 w/0 Bit <6:0> PLLINTn PLLINTn Integer division ratio bit <6:0> Multi-modulus divider integer offset value (7 bits) for Channel A, B, C, and D ADDR 0x0A, 0x0E, PLLFRACn0--PLL Fractional Division Ratio 0x12, 0x16 n: Channel A, B, C, D (byte 0) Bit 7 PLLFRACn0 Bit 6 PLLFRACn0 Bit 5 PLLFRACn0 Bit 4 PLLFRACn0 Bit 3 PLLFRACn0 Bit 2 PLLFRACn0 Bit 1 PLLFRACn0 Bit 0 PLLFRACn0 w/0 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:0> PLLFRACn0 PLLFRACn0 Fractional division ratio bit <7:0> Synthesizer channel frequency value (21 bits, bits < 7:0 >), Fractional division ratio for Channel A, B, C, and D ADDR 0x0B, 0x0F, PLLFRACn1--PLL Fractional Division Ratio 0x13, 0x17 n: Channel A, B, C, D (byte 1) Bit 7 PLLFRACn1 Bit 6 PLLFRACn1 Bit 5 PLLFRACn1 Bit 4 PLLFRACn1 Bit 3 PLLFRACn1 Bit 2 PLLFRACn1 Bit 1 PLLFRACn1 Bit 0 PLLFRACn1 w/0 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:0> PLLFRACn1 PLLFRACn1 Fractional division ratio bit <15:8> Synthesizer channel frequency value (21 bits, bits < 15:8 >), fractional division ratio for Channel A, B, C, and D Data Sheet 39 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x0C, 0x10, PLLFRACn2--PLL Fractional Division Ratio 0x14, 0x18 n: Channel A, B, C, D (byte 2) Bit 7 n.u. Bit 6 n.u. Bit 5 reserved Bit 4 PLLFRACn2 Bit 3 PLLFRACn2 Bit 2 PLLFRACn2 Bit 1 PLLFRACn2 Bit 0 PLLFRACn2 / Bit 5 / reserved w/0 w/1 w/0 Set always to 0 w/0 w/0 w/0 Bit <4:0> PLLFRACn2 PLLFRACn2 Fractional division ratio bit <20:16> Synthesizer channel frequency value (21 bits, bits < 20:16 >), fractional division ratio for Channel A, B, C, and D 2.4.7 Digital FSK/GFSK Modulator The TDA 5150 uses an integrated direct FSK Modulator for generation of RF-signals. By this method, and assuming NRZ data encoding, a positive frequency deviation (relative to nominal carrier frequency) occurs for a logical "1" of the already encoded data, and a negative frequency deviation for a logical "0" if the data inversion bit INVERT in SFR TXCFG1 (0x05.3) is 0 (inversion OFF). If the inversion function is active (INVERT bit is set to 1), the frequency shift directions are inverted (i.e. negative frequency deviation for logical "1" of input data and positive deviation for "0") for the same NRZ data stream. Note: if an encoding scheme other then NRZ is choosen, then data bits are decomposed in elementary chips, as shown in Figure 10 and above two statements regarding input data inversion state (on/off) versus frequency shift direction are true, but apply instead of input data bit, to the resulting chips. The two frequencies, corresponding to positive and negative frequency shift are directly associated with specific divider numbers. The modulation is achieved by switching between these two divider numbers and it takes effect under the control of data signal state (and encoding scheme, if other then NRZ). The above described (divider ratio switching) method is called direct FSK modulation. With direct FSK modulation a well controlled frequency shift can be achieved and the pullability of the crystal in the reference frequency oscillator circuit is no issue anymore, like by the classical FSK, where usually a reactance does "pull" the crystal frequency. Also a data shaping is realized in digital domain, as Gaussian filtered FSK (GFSK) and can be enabled by setting the GFBYP bit of SFR GFXOSC (0x1E.3) to 0. Data Sheet 40 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description The GFSK modulation can further reduce the occupied RF bandwidth versus FSK modulation. The ASK or FSK modulation type is selected by a bit-field in SFR TXCFG1 (0x05). There are two possible setups, denoted ModulationSetting1, and ModulationSetting2. A field within Transmit Command Byte (referenced as bit D in Transmit Command byte) selects one of the two settings as active. This allows for fast commutation between modulation parameters without additional (re)configuration and repeated register downloads. See also Chapter 2.4.3.4 Transmit Command for details. Figure 14 Spectrum for FSK and Gaussian FSK (GFSK) modulated RF-signals, both with 20 kbit/s datarate and + 35 kHz FSK deviation. Blue plot corresponds to FSK and green plot to GFSK modulation. and The frequency deviation is configured using the bits FDEF<4:0> FDEVSCALE<2:0> in the SFR FDEV(0x1C.7:0) and is calculated as follows: 2 190 x FDEV< 4:0 > x -------------------------------------------- + 0.5 64 = f XOSC x -------------------------------------------------------------------------------------------------------------------21 2 - 0.5 FDEVSCALE< 2:0 > f RF Note that the FSK deviation is referenced to the center frequency. This means, that the spacing between the two FSK frequencies, is twice the FSK deviation. The pulse-shaping Gaussian Filter used for GFSK can be disabled if regular FSK is used. In ASK mode the filter is always switched off. For ASK mode a power-sloping mechanism is available and described in detail in Chapter 2.4.8 Power Amplifier, ASK Modulator. Data Sheet 41 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description The Gaussian shaping is defined as a number of fixed frequency steps (transitions) between the 2 FSK frequencies, corresponding to Low and High, or 0 and 1 on the modulator input. It is understood that the steps are counted over one edge of the data chip. Ideally these 16 steps are distributed over the complete data chip length, which means there are 16 gaussian filter steps per chip or NGF = 16. Selecting NGF > 16 will reduce the shaping effect and selecting NGF < 16 will cause a reduction of signal information, with minimal positive effect on the obtained RF spectrum. . 1 Data chip 0 1 0 1 0 16 steps/chip = ideal gaussian 25 steps/chip 11 steps/chip Figure 15 Influence of the Gaussian Divider on Data Shaping The content of GFDIV is calculated as follows: f XOSC GFDIV = --------------------------------------- - 1 chiprate x N GF It is recommended to program the GFDIV register in such way, that the GF divider NGF is 16 times the chip-rate. This allows optimum Gaussian filtering. Data Sheet 42 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.7.1 SFRs related to digital FSK / GFSK Modulator ADDR 0x1C Bit 7 w/1 Bit 6 w/1 FDEV--Frequency Deviation Bit 5 w/0 Bit 4 FDEV Bit 3 FDEV Bit 2 FDEV Bit 1 FDEV Bit 0 FDEV FDEVSCALE FDEVSCALE FDEVSCALE w/1 w/1 w/1 w/1 w/1 Bit <7:5> FDEVSCALE Bit <4:0> FDEV FDEVSCALE Frequency deviation scaling bit <2:0> Frequency deviation bit <4:0> Scaling of the frequency deviation (3 bits) 000: 001: 010: 011: divide by 64 divide by 32 divide by 16 divide by 8 100: divide by 4 101: divide by 2 110: divide by 1 111: multiply by2 FDEV Frequency deviation value (5 bits), defines the multiplication value for the output data from the Gaussian filter (0-31) ADDR 0x1D Bit 7 GFDIV GFDIV--Gaussian Filter Divider Value Bit 6 Bit 5 GFDIV Bit 4 GFDIV Bit 3 GFDIV Bit 2 GFDIV Bit 1 GFDIV Bit 0 GFDIV GFDIV w/0 w/0 w/0 w/0 w/1 w/0 w/0 w/0 Bit <7:0> GFDIV GFDIV Gaussian filter divider bit <7:0> Gaussian filter clock divider value (11 bits, bits < 7:0 >), defines the sampling ratio of the Gaussian filter; typically this value is set such that the GF divider NGF is 16 x chip-rate (for ideal Gaussian filtering) Note: bits < 10:8> are contained in GFXOSC register ADDR(0x1E) Data Sheet 43 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x1E Bit 7 FHBLANK GFXOSC--Gaussian Filter Configuration Bit 6 Bit 5 reserved Bit 4 reserved Bit 3 GFBYP Bit 2 GFDIV Bit 1 GFDIV Bit 0 GFDIV reserved w/0 Bit 7 Bit 3 w/1 FHBLANK w/1 w/1 w/1 w/0 w/0 w/0 GFBYP Gaussian filter bypass Gaussian filter divider bit <10:8> Bit <2:0> GFDIV FHBLANK Frequency Hopping disable (defines the jump from the TX_TIMEOUT state) 0: enable (jump to TX_ON state) 1: disable (jump to PLL_ON state) GFBYP GFDIV Gaussian filter bypass: 0: GF enabled 1: GF bypassed Gaussian filter clock divider value (11 bits, bits < 10:8 >), defines the sampling ratio of the Gaussian filter, typically this value is set such that the GF divider is 16 x chip-rate (for ideal Gaussian filtering) Note: bits < 7:0> are contained in GFDIV register ADDR(0x1D) Data Sheet 44 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.8 Power Amplifier, ASK Modulator The RF signal, generated by VCO and under the control of the Sigma-Delta fractionalN PLL is fed to a group of class-C Power Amplifier stages, before being transmitted. The Power Amplifier (PA) includes an output power control, ASK sloping, switchable capacitors for antenna fine tuning and an auto switch -off mechanism, as part of the FailSafe system. If critical supply voltage or frequency error events occur, the Fail-Safe mechanism switches off the PA, thus preventing erroneous transmissions... TDA 5150 from SDPLL PA matching network (external) ASK sloping ASK-data Figure 16 Transmitter Blocks In FSK or GFSK mode, the PA is always ON during the transmission's duration. By ASK mode, the SDPLL delivers a continuous RF signal to the PA. The PA is switched ON and OFF, according the data signal to be transmitted. Additionally there is an ASK sloping mechanism, which switches the different power stages ON (and OFF) in a well determined sequence, correlated with the transitions on data signal line. This power ramping procedure minimizes out-of band transients and spectral splatter. 2.4.8.1 PA Output Power Programming The PA comprises 11 elementary cells in parallel. Each one is a class-C amplifier. The cells are grouped in three PA blocks. PA Block 0 is composed of 9 stages, PA Block 1 and PA Block 2 are strong single stages. Each PA Block can be individually enabled and disabled to optimize power consumption and efficiency in an output power subrange. The overall 11 PA stages allow control of the RF output power in 11 steps over a range of 20 dB. The PA can be switched OFF by disabling all the 11 stages. Data Sheet 45 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description . ASK_DATA PO UT 4 PA_PS bit2 - stage 11 PA_PS bit1 - stage 10 PA_PS bit0 - stages 9-1 PAout 1 1 9 SLOPDIV 10 PA & ASK Sloping control VDD from SDPLL Driver 1 PA_PS bit2 PA_PS bit1 PA_PS bit0 Figure 17 PA Core with Output Power Control Two independent PA power level settings can be configured. With the Transmit Command the PA power level is selected together with the modulation setting. This means, either power level 1 AND modulation type 1 or power level 2 AND modulation type 2 are selected, according to Modulation Setting 1 or Modulation Setting 2 field in Transmit Configuration byte. The 3 PA Blocks are enabled by PA_PS1 and PA_PS2 bits within SFR POWCFG0 (0x1A). The bits PA_PS1 do enable the PA blocks for power level 1 and bits PA_PS2 are used for power level 2. Enabling the 3 PA Blocks offers following typical PA ranges (note that the PA output power depends also on the external matching circuit, at a quite large extent): * * * PA_PS bit0=1: 5dBm matched; Pout = +5dBm down to -10dBm, 9 PA Stages PA_PS bit1=1: 8dBm matched; Pout = +8dBm down to -10dBm, 10 PA Stages PA_PS bit2=1:10dBm matched; Pout = +10dBm down to -10dBm, 11 PA Stages In addition to enabling the PA Blocks, the 11 PA stages have to be configured. This is achieved by setting the bit-fields POUT1 (0x1B.3:0) for power level 1 and POUT2 (0x1B.7:4) for power level 2 in SFR POWCFG1 (0x1B) (POUTn=0 means that the PA is effectively OFF). Data Sheet 46 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description The output impedance of the PA depends on the number of PA stages used. The external antenna matching must be done for the impedance related to the highest number of used PA stages, or in other words, for the use-case of highest RF output power.If the desired output power is +10dBm for instance, the antenna should be matched for the case of all the11 PA Stages active. In the same way, if the output power requirement is for +5dBm, the antenna should be matched assuming that 9 PA Stages are used and active. Supposed the matching network have been set up for the PA impedance bound to +10dBm output power (all 11 PA Stages active), it is reasonable to expect some degree of mismatch and efficiency loss by operation in +5dBm RF power mode. 2.4.8.2 ASK Modulation and ASK Sloping The ASK or FSK modulation is selected by SFR TXCFG1 (0x05). There are two possible setups, designated ModulationSetting1, and ModulationSetting2. The bit D of Transmit Command Byte selects the active setting. This allows switching between the two modulation setups, without any further register configuration. See also Chapter 2.4.3.4 Transmit Command ASK modulation is realized by switching the PA Stages ON and OFF in accordance with data signal to be transmitted. On-chip ASK Sloping capability is provided within TDA 5150. This means that instead of switching all PA Stages at the same time, they are switched ON one after the other in a configurable time sequence.The power sloping is controlled by SFR SLOPDIV (0x19.7:0). The register content is equal with the number of reference oscillator cycles elapsed until the next PA stage is switched ON or OFF. Note: For optimum shaping effect, it is recommended to match the number of sloping steps to the required maximum output power and consequently to the maximum number of stages which might be used. 2.4.8.3 Duty Cycle Control The control of Duty Cycle leads to control of the averaged RF output power (by changing the conductive angle of the power amplifier) and contributes to further reduction of the current consumption. It is worth to be noted, that the decreasing conduction angle values lead to decrease of power consumption, but due to the short and high-amplitude current pulses the level of RF harmonics (on n*fcarrier frequencies) tends to rise. Proper measures (filtering) must be taken to maintain harmonics level rejection. If Duty Cycle control option is enabled, nominal values of 27%, 33%, 39% and 44% can be programmed. If disabled, the default value of 50% applies for Duty Cycle. Data Sheet 47 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description The Duty Cycle Control is accessible through the bits DCCCONF (0x1F.5:4) of SFR ANTTDCC (0x1F).See Chapter DCCCONF for details. In the 315 MHz band the DCCCONF and DCCDISABLE bits are ignored and the optimized (and predefined) value of 33% Duty Cycle is superimposed 2.4.8.4 Antenna Tuning A block of 4 switchable capacitors is paralleled with the PA output. The Antenna Tuning option can be useful for fine-tuning the PA to Load matching network, and thus to obtain a better antenna performance in a wider frequency band. This feature is useful by multichannel applications, for maintaining antenna matching close to the optimum. The tuning capacitors can be switched ON / OFF individually and the control of the switches is implemented in SFR TUNETOP (0x1F). . VBAT TDA 5150 PA_IN PA Antenna Choke PA C1 switched caps 0.06~0.9pF (incl. parasitic from PA) C2 TUNETOP Ant Tune Ctrl Figure 18 PA Antenna Tuning and Matching The 4 switched capacitors have different values of typically 60 fF, 120 fF, 240 fF and 480 fF, giving an overall maximum capacitance of about 0.9 pF. Note: Due to the low Q Factor of the switched capacitors at the higher frequencies, the devices current consumption tends to increase when this feature is used in the 868 MHz and 915 MHz frequency bands. Data Sheet 48 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.8.5 Fail-Safe PA Switch Off To prevent erroneous transmissions (on wrong frequency or with erroneous modulation parameters, altered payload etc.) the activation of Fail-Safe mechanism is coupled with deactivation (switching off) of the RF Power Amplifier stages. If critical errors occur, the Fail-Safe mechanism incorporated in the TDA5150 is activated, provided the detection enable bit is armed (i.e. bit FSOFF in SFR TXCFG0 (0x04.4) is 0). Observe that this corresponds to the after-reset state. In other words, by exiting the reset state, the Fail-Safe detection is already armed, but it can be deactivated anytime by changing its control bit state to High (bit FSOFF=1 (0x04.4)) or rearmed, by setting it to Low. If the detection is armed, RF Power Amplifier drivers are automatically switched OFF in case of an error, to prevent erroneous transmissions. This happens if at least one of the following events occurs: * * * Parity error in the SFRs Brownout event (event sensed by the brown-out detector BOD) PLL lock failure is detected (event sensed by the lock detector LD) If the detection is disabled, the error flags in Transmitter Status Register (0x01) still keep track of error status (i.e. they are set, if an error occurs) but the RF Power Amplifier is not switched off by the error flag(s) set condition (i.e. the RF-PA continues to transmit despite error until the transmission is terminated as a normal, error-free one). Refer to Transmitter Status Register (0x01) description and Fail-Safe Flags, explained in next Chapter 2.4.8.6 SFRs related to RF Power Amplifier and ASK Modulator. Data Sheet 49 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.8.6 SFRs related to RF Power Amplifier and ASK Modulator ADDR 0x04 Bit 7 GO2STDBY TXCFG0--Transmitter Configuration Register 0 Bit 6 Bit 5 reserved Bit 4 FSOFF Bit 3 ISMB Bit 2 ISMB Bit 1 reserved Bit 0 reserved reserved cw/0 Bit 4 w/0 FSOFF w/0 w/0 w/0 w/1 w/1 w/0 Fail-Safe mechanism: 0 enabled, 1 turned off ADDR 0x05 Bit 7 GO2SLEEP TXCFG1--Transmitter Configuration Register 1 Bit 6 Bit 5 ASKFSK1 Bit 4 ASKSLOPE Bit 3 INVERT Bit 2 w/1 Bit 1 w/0 Bit 0 w/1 ASKFSK2 ENCMODE ENCMODE ENCMODE cw/0 Bit 4 w/0 ASKSLOPE w/1 w/0 w/0 ASK sloping: 0 disable, 1 enable ADDR 0x19 Bit 7 SLOPEDIV SLOPEDIV --ASK Sloping Clock Divider Bit 6 Bit 5 SLOPEDIV Bit 4 SLOPEDIV Bit 3 SLOPEDIV Bit 2 SLOPEDIV Bit 1 SLOPEDIV Bit 0 SLOPEDIV SLOPEDIV w/1 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:0> SLOPEDIV SLOPEDIV ASK sloping clock divider bit <7:0> ASK sloping clock division ratio (10 bits, bits < 7:0 >), defines the timing of the ASK signal shaping using PA power stage switching Range: from 0x000: SLOPEDIV = 1 to 0x3FF: SLOPEDIV = 1024 Data Sheet 50 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x1A Bit 7 PA_PS2 POWCFG0--PA Output Power Configuration Register 0 Bit 6 Bit 5 PA_PS2 Bit 4 PA_PS1 Bit 3 PA_PS1 Bit 2 PA_PS1 Bit 1 SLOPEDIV Bit 0 SLOPEDIV PA_PS2 w/0 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:5> PA_PS2 Bit <4:2> PA_PS1 Bit <1:0> SLOPEDIV PA_PS2 PA output blocks setting 2 bit <2:0> PA output blocks setting 1 bit <2:0> ASK sloping clock divider bit <9:8> Individual control of the 3 PA blocks, setting 2 (3-bits) 0: disabled 1: enabled Bit(0) ==> PA block 0 Bit(0) ==> PA block 0 Bit(1) ==> PA block 1 Bit(1) ==> PA block 1 Bit(2) ==> PA block 2 Bit(2) ==> PA block 2 PA_PS1 Individual control of the 3 PA blocks, setting 1(3-bits) 0: disabled 1: enabled SLOPEDIV ASK sloping clock division ratio (10 bits, bits < 9:8 >), defines the frequency of the ASK signal shaping using PA power stage switching Range: from 0x000: SLOPEDIV = 1 to 0x3FF: SLOPEDIV = 1024 ADDR 0x1B Bit 7 POUT2 POWCFG1--PA Output Power Configuration Register 1 Bit 6 Bit 5 POUT2 Bit 4 POUT2 Bit 3 POUT1 Bit 2 POUT1 Bit 1 POUT1 Bit 0 POUT1 POUT2 w/0 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:4> POUT2 Bit <3:0> POUT1 POUT2 Output power setting 2 bit <3:0> Output power setting 1 bit <3:0> PA output power setting 2 (4 bits), defines the number of enabled PA stages Range: from 0x0: POUT2 = 0 to 0xB: POUT2 = 11 > 0xB: POUT2 = 11 to 0xB: POUT1 = 11 > 0xB: POUT1 = 11 POUT1 PA output power setting 1 (4 bits), defines the number of enabled PA stages Range: from 0x0: POUT1 = 0 Data Sheet 51 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x1F ANTTDCC--Antenna Tuning and Duty Cycle Configurations Bit 6 DCC DISABLE Bit 7 reserved Bit 5 DCCCONF Bit 4 DCCCONF Bit 3 TUNETOP Bit 2 TUNETOP Bit 1 TUNETOP Bit 0 TUNETOP w/0 Bit 7 Bit 6 Bit 3:0 w/0 reserved w/1 w/0 w/0 Always use 0 w/0 w/0 w/0 DCCDISABLE TUNETOP Duty cycle control disable Duty cycle control delay configuration bit <1:0> Antenna tuning top capacitor bit <3:0> Bit <5:4> DCCCONF DCCDISABLE DCCCONF Duty cycle control disable (must be 0 for ISMB=0) 0 enabled 00: 43% (69/35/33 ps) 01: 39% (207/104/9 8 ps) 10: 35% (346/173/ 164 ps) 1 disabled (delay = 0ps) 11: 31% (484/242/ 230 ps) Duty cycle control delay configuration (ISMB = 1/2/3, for ISMB = 0 => delay = 0 ps) TUNETOP Antenna tuning top capacitor selection (4-bits): Individual switch of capacitor banks Bit(0) ==> 60 fF Bit(1) ==> 120 fF 0: switched off Bit(2) ==> 240 fF Bit(3) ==> 480 fF 1: switched on 2.4.9 Operating Modes TDA 5150 has 3 main operating modes: SLEEP, STANDBY, TRANSMIT and 2 temporary modes: XOSC_ENABLE and PLL_ENABLE. 2.4.9.1 SLEEP Mode SLEEP is the lowest power consumption mode. Most of the internal blocks, excepting the SPI interface are powered down and consequently the content of SFRs is going lost. Therefore the SFR bank requires a full reprogramming after exiting SLEEP mode. The SPI interface stays active and is supplied via the Low Power Voltage Regulator while in SLEEP mode. The SPI interface is able to detect bus non-idle conditions and it will wake up the transmitter if the EN pin is taken high and at least 3 pulses are applied to SCK pin. Data Sheet 52 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description Observe that this last wakeup condition is automatically fulfilled during communication over the transmitter's SPI-bus, assuming a standard, SPI-bus protocol is used. SLEEP mode is entered: * after a GO2SLEEP command execution, i.e by taking the EN pin to Low preceded by setting of the GO2SLEEP bit in SFR TXCFG1 (0x05.7) to 1. This bit will be cleared automatically on WAKEUP (i.e. on exiting the SLEEP state). There is a small latency after the trailing edge of signal on EN pin (of 2 fsys cycles) the time taken to close down internal blocks. SLEEP mode is left if the EN line is set to High level and there is clock activity (at least 3 pulses) on the SCK line. The conjunction of these 2 conditions will wake up the transmitter and thus SLEEP Mode will be exited. In SLEEP mode: * * * * * * Only the low power voltage regulator is ON Only the SPI interface is powered POR is ON BOD is in low power mode (inaccurate threshold) All other blocks are OFF. Power supply for digital core and SFR data is disconnected. As a consequence, SFR register content is lost. 2.4.9.2 STANDBY Mode (Data Retention Mode) STANDBY is a low power mode, but with higher consumption as SLEEP mode, due to the fact that the SFRs are still supplied in this mode. STANDBY is entered: * * whenever the EN line is low (no SPI communication), and the time-out count of 65536/ fsys periods have been elapsed after a GO2STANDBY command execution (setting the GO2STANDBY bit in SFR TXCFG0 (0x04.7) followed by taking the EN pin to Low (EN=0). Only the low power voltage regulator is ON SPI, SFR container, and System Controller are supplied - data can be read into and from the chip. POR is ON BOD is in low-power mode (inaccurate threshold) Data consistency of SFR container is monitored by means of parity bits In STANDBY Mode: * * * * * All other blocks are OFF. Data Sheet 53 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.9.3 TRANSMIT Mode This mode is automatically entered during a transmit command. PLL and PA are active i this mode. TRANSMIT is left, with the falling edge of the EN line, when bit B in the Transmit Command is 0. Otherwise TDA 5150 remains in the transmit mode with PA and PLL in ON state, until the time-out of 65536 / fsys occurs (around ~5 ms for a 13 MHz reference clock). * * * * * * Normal voltage regulator is ON POR is ON BOD is ON XOSC is ON PLL is ON PA is ON 2.4.9.4 XOSC_ENABLE Mode This is a temporary mode after power up, entered whenever SLEEP or STANDBY mode is left (by a rising edge of the EN line). This mode is automatically entered while SFRs are programmed. XOSC_ENABLE is left by GO2SLEEP, GO2STANDBY commands, by the ~5 ms time-out to enter automatically STANDBY, or by a transmit command. * * * * * * Normal voltage regulator is ON POR is ON BOD is ON XOSC is ON Clock divider is ON PLL and PA are OFF 2.4.9.5 PLL_ENABLE Mode This is a temporary mode during a transmit command, when the PLL is already activated, but the PA is not switched ON yet. * * * * * Normal voltage regulator is ON POR is ON BOD is ON XOSC is ON PLL is ON, PA is OFF Data Sheet 54 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description Power-On-Reset Transmit command [EN = 1] & [Activity on SCK ] ( clock pulses ) SLEEP = 1 XOSC_ENABLE EN = 0 PLL_ENABLE (PA OFF) Timeout = 1 or GO2STDBY = 1 PA OFF during frequency hop SCK edge detected EN = 1 EN = 0 and TXCFG.B = 0 SLEEP STANDBY TRANSMIT (PA ON) PA ON during frequency hop Timeout = 1 and TXCFG.B = 1 Figure 19 Simplified State Diagram of the TDA 5150 Data Sheet 55 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.9.6 SFRs related to Operating Modes ADDR 0x04 Bit 7 GO2STDBY TXCFG0--Transmitter Configuration Register 0 Bit 6 Bit 5 reserved Bit 4 FSOFF Bit 3 ISMB Bit 2 ISMB Bit 1 reserved Bit 0 reserved reserved cw/0 Bit 7 w/0 GO2STDBY w/0 w/0 w/0 w/1 w/1 w/0 1: go to StandBy, (cleared after 1 is written) ADDR 0x05 Bit 7 GO2SLEEP TXCFG1--Transmitter Configuration Register 1 Bit 6 Bit 5 ASKFSK1 Bit 4 ASKSLOPE Bit 3 INVERT Bit 2 w/1 Bit 1 w/0 Bit 0 w/1 ASKFSK2 ENCMODE ENCMODE ENCMODE cw/0 Bit 7 w/0 GO2SLEEP w/1 w/0 w/0 1: go to Sleep Note: after execution of this command all SFR content is lost Data Sheet 56 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.10 Fail-Safe Mechanism and Status Register 2.4.10.1 Fail-Safe Flags The status of the TDA 5150 is continuously monitored during active state. The integrated Fail-Safe mechanism includes: * Brownout Error--generates an internal reset, whenever the voltage drops below the specific threshold. The brownout error flag is set, to allow recognition of a brownout event.The flag can be red via SPI bus. Parity Error-- There is a single parity bit for each SFR register, which is updated each time the SFR register is written. Following this update, the parity for each register is calculated and checked against this bit continuously. If there is a mismatch in any of the registers, the error flag is set. The content of all SFRs is monitored and the parity checked even during STANDBY state. PLL Lock Error--is monitored after the transmission start. If the PLL loses the phaselocked state during transmission, the related flag is set. * * The Fail-Safe status of the chip is stored and available via the SFR Transmitter Status Register (0x01).If a failure condition occurs, a flag is set and latched via previously mentioned SFR.Even if the condition which led to the event occurrence is no longer true, the "set" state of the Fail-Safe bits is kept, and cleared only by the Transmitter Status Register read operation. See also Chapter 2.5.2 for detailed SFR register map. Preservation of above described Fail-Safe Flag bits in SFR Transmitter Status Register provides a feedback to user about the failure root cause - if any error occurred. If the Transmit Fail-Safe mechanism FSOFF in SFR TXCFG0 (0x04) is enabled (set to 1) and one of the Fail-Safe flags is set, the PA is disabled thus preventing further transmission. It is highly recommended to read the SFR Transmitter Status Register (0x01) beforeand after a transmission (clear error flags, if any and check for error-free transmission). 2.4.10.2 Low Battery Monitor The low-battery detector monitors the supply voltage on Pin 5 (VBAT). If the voltage drops below 2.4 V, a corresponding flag is set and the threshold is switched automatically to 2.1 V. If this new threshold is also reached due to further voltage drop, the 2.1 V flag bit is set in addition to the 2.4 V flag. These Fail-Safe flags are automatically cleared after each transmission start, and content is not preserved like for Brownout Error, Parity Error and PLL Lock Error bits. Summary: * * LBD_2V4 set if battery voltage drops below 2.4 V LBD_2V1 set if battery voltage drops below 2.1 V Data Sheet 57 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.10.3 SFRs related to Supply Voltage monitoring ADDR 0x01 Bit 7 1 TXSTAT--Transmitter Status Register Bit 6 n.u. Bit 5 LBD_2V1 Bit 4 LBD_2V4 Bit 3 c/0 Bit 2 c/1 Bit 1 PARERR Bit 0 PLLLDER VAC_FAIL BROUTERR / Bit 7 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 LBD_2V1 LBD_2V4 BROUTERR PARERR PLLLDERR 1 / r/0 r/0 c/0 c/0 Set to 1, mandatory Low battery detected at 2.1 V Low battery detected at 2.4 V Don't care Brown out event Parity error PLL lock detector error LBD_2V1 LBD_2V4 reserved BROUTERR PARERR PLLLDER Battery voltage drop below 2.1 V detected if 1 - in standby mode, bit is invalid Battery voltage drop below 2.4 V detected if 1 - in standby mode, bit is invalid Brownout event detected if 1 Parity error detected if 1 PLL lock error detected if 1 Data Sheet 58 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.11 RF Data Transmission The procedure of RF Transmission starts by rising the EN line (pin 1) high. STANDBY or SLEEP Mode are exited, and the crystal oscillator started. The crystal oscillator requires maximum 1 ms to start up. During this time the TDA 5150 can be already reconfigured, because the SPI block does not require the system clock. Before transmission the Transmitter Status Register (0x01) should be read (to clear bits set by previous errors, if any). Every transmission starts with the Transmit Command: C1 1 C0 Bit 1 A Transmit Command Configuration Function Data sync Value, description 0: off 1: on (at the same time Bit C - Encoding must be set also to 1 -->int. Encoding) 0: PA off at the falling edge of EN (synchronized with bit-rate if bit A is high) 1: SDIO/DATA is latched at the falling edge of EN, PA stays on, TX data are kept constant. After the time-out of 65536 / fsys which is ~5 ms for a 13 MHz crystal, PA and PLL are switched off. 0: off 1: on (selects SFR register for encoding Bit A must be also set to1 -->Data sync) 1 1 B PA mode 1 1 C Encoding 1 1 1 1 D Pwr. level/ 0: selects PowerLevel/Modulation Setting1 ModSetting 1: selects Power Level/Modulation Setting2 Frequency 0 (00): selects frequency channel A selection 1 (01): selects frequency channel B 2 (10): selects frequency channel C 3 (11): selects frequency channel D (for description of frequency channels A..D programming see Chapter 2.4.11.3 Channel Hopping) The Transmit Command byte is sent via SPI, and identified by the first two bits, designated C0 and C1. These two bits are mandatory set to1. The following 6 bits, designated bit A.. bit F, specify the transmission details. * A: Synchronous (1) or asynchronous (0) transmission, details are described later in this chapter. Data Sheet 59 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description * B: If 0, the PA is switched off by the falling edge of the EN line. If 1, the SDIO line is latched with the falling edge of EN, the PA stays active, continuing to transmit according to the latched SDIO state. After a time-out duration of 65536 / fsys (~5 ms for a 13 MHz reference clock), both the PA and PLL are switched off if no other SPI command starts a new transmission. This feature helps to keep the transmitter sending, despite the fact that the EN line is pulled to Low state, normally a stop condition for Transmitter. Pulling the EN line to (Low) in between SPI command blocks is required by SPI protocol, if commands are not sent in burst mode. C: If C=0, the Encoder is not used. If C=1, the Encoder is used as configured in the Transmitter Configuration Register 1, bits ENCMODE (0x05.2:0). D: Switch between two subsets of transmission parameters, referenced as PowerLevel/Modulation Setting n. Each subset contains 3 bit-fields for control of: - modulation type (ASK or FSK) - RF-PA block activation (3 blocks are available, may be switched ON/OFF individually) - RF-PA output power Modulation type (ASK or FSK) is controlled by bit-field ASKFSK1:2 (0x05.6:5) of the SFR Transmitter Configuration Register 1 (0x05). The modulation type selection is done individually for each of the two transmission settings (steered by bit D=0 or D=1), with choice between ASK and FSK modulation. The settings are not coupled, i.e one could be set for ASK modulation and the other for FSK for example. Further, if FSK is chosen as modulation type, enabling of Gaussian filtering is another option - but not mandatory. See also Chapter 2.4.4.2 SFRs related to Transmitter Configuration and Data Encoding. RF-PA block activation, controlled by bit-fields PA_PS1 (0x1A.4:2) respectively PA_PS2 (0x1A.7:5) of the SFR Output Power Configuration Register 0, (0x1A) for the two transmission settings RF-PA output power selection, controlled by the bit-fields POUT1 (0x1B.3:0) respectively POUT2 (0x1B.7:4) of the SFR Output Power Configuration Register 1, (0x1B) for the two transmission settings If D=0, following fields are selected: [ASKFSK1, together with PA_PS1 and POUT1]. If D=1, following fields are selected: [ASKFSK2, together with PA_PS2 and POUT2]. E, F RF Frequency selection as configured in PLL MM Integer Value registers A/B/C/D (0x09/0x0D/0x11/0x15) and the PLL Fractional Division Ratio registers A/B/C/D (0x0A:0x0C/0x0E:0x10/0x12:0x14/0x16:0x18. * * - - - - * After the transmit command have been sent, the SCLK line has to stay low for at least 100 s (i.e settling time of the PLL). A rising edge of the SCLK line after this brake activates the PA and starts the transmission. The digital data is input into the transmitter via the SDIO line and transposed into modulated RF signal, without regard on the state of SCLK line (which could be Low or High). To keep crosstalk between SCLK and SDIO at minimum level, it is recommended to keep SCLK at a steady level, instead of toggling it (usually by the uC). Data Sheet 60 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.11.1 Asynchronous Transmission In Asynchronous Transmission Mode (also referred as Transparent Mode), the data on SDIO is directly input into modulator and converted into RF carrier.There is no internal synchronization with the bit-rate clock.The CLKOUT programmed to the proper bit-rate (or a multiple of it) may be used by the host to time and shift (into SDIO line) the bits to be transmitted. The Encoder and Scrambler can not be used and are automatically bypassed. It is not recommended to use GFSK in conjunction with Asynchronous Transmission Mode, as the frequency steps are timed with 1/16 of the bit-rate (chip-rate) clock. Timing differences between the internal bit-rate clock and the C may cause unwanted jitter in the transmission. GFSK modulation is intended to be used in conjunction with Synchronous Transmission Mode. TRANSMIT data: Asynchronous Transmission EN > 1000us if TX issued from STDBY else determined by SCK speed > 100us 7 0 SCK Command Configuration Data to transmit SDIO 1 1 A B C D E F d1 d2 d3 d4 d5 Transmitted Data d1 d2 d3 d4 d5 Figure 20 Asynchronous Transmission Setting the EN line (pin 1) to low terminates the RF-transmission. Data Sheet 61 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.11.2 Synchronous Transmission In the Synchronous Transmission Mode the transmit data is latched with the falling edge of the internal bit clock, and thus synchronized. The bit clock at the CLKOUT has to be used by the C to time the bits which are transmitted, e.g. on interrupt basis. The Encoder has to be enabled. If the bits shall not be encoded, select NRZ as generic Encoder scheme. See Chapter 2.4.4 Data Encoder. TRANSMIT data: Synchronous Transmission EN > 1000us if TX issued from STDBY else determined by SCK speed > 100us 7 0 SCK Command delay SDIO 1 1 A B C D 0 E F d1 d2 d3 d4 d5 Bit-rate Signal Transmitted Data d1 d2 d3 d4 d5 Figure 21 Synchronous Transmission Synchronous transmission is the recommended user mode. Encoding can be used, this mode is preferred for GFSK. At the same time SW implementation is easier, because the setting of the next data bit on SDIO is triggered by interrupt (CLKOUT line) and timing inacuracies e.g. caused by interrupt reaction latency are compensated / neutralized by the synchronization. Data Sheet 62 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.4.11.3 Channel Hopping TDA 5150 offers the possibility for usage of up to 4 preconfigured RF channels, called A, B, C, and D frequency channels. The preconfiguration assumes proper programming PLL's Multi-Modulus Integer Value registers A/B/C/D (0x09/0x0D/0x11/0x15) and the PLL Fractional Division Ratio registers A/B/C/D (0x0A:0x0C/0x0E:0x10/0x12:0x14/0x16:0x18. Bit-filed 2.4.11.4 SFRs related to Channel Hopping ADDR 0x1E Bit 7 FHBLANK GFXOSC--Gaussian Filter Configuration Bit 6 Bit 5 reserved Bit 4 reserved Bit 3 GFBYP Bit 2 GFDIV Bit 1 GFDIV Bit 0 GFDIV reserved w/0 Bit 7 FHBLANK w/1 FHBLANK w/1 w/1 w/1 w/0 w/0 w/0 Frequency Hopping VAC Disable Frequency Hopping, enable/disable VCO Auto Calibration for Channel Hopping 0: enable VCO Auto Calibration (default) 1: Skip VCO Auto Calibration for frequency hops <1MHz Data Sheet 63 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.5 2.5.1 Digital Control (SFR Registers) SFR Register List The SFRs (Special Function Registers) are used to configure TDA 5150 and to read out certain information e.g. the transmitter status. There are complete SFRs, as well as register bits in SFRs, called "Reserved". These SFRs and register bits used in the production process. The SFRs and bits have to be configured with their default value as shown in the Chapter 2.5.2 SFR Detailed Descriptions Table 3 SFR Register List Register Description SPI Checksum register Transmitter status register Transmitter configuration register 0 Transmitter configuration register 1 Clock pre- and after-scaler BDRDIV divider PRBS start value PLL MM integer value Channel A PLL fractional division ratio Channel A (byte 0) PLL fractional division ratio Channel A (byte 1) PLL fractional division ratio Channel A (byte 2) PLL MM integer value Channel B PLL fractional division ratio Channel B (byte 0) PLL fractional division ratio Channel B (byte 1) PLL fractional division ratio Channel B (byte 2) PLL MM integer value Channel C PLL fractional division ratio Channel C (byte 0) PLL fractional division ratio Channel C (byte 1) PLL fractional division ratio Channel C (byte 2) PLL MM integer value Channel D PLL fractional division ratio Channel D (byte 0) 64 Register Name SPICHKSUM TXSTAT TXCFG0 TXCFG1 CLKOUTCFG BDRDIV PRBS PLLINTA PLLFRACA0 PLLFRACA1 PLLFRACA2 PLLINTB PLLFRACB0 PLLFRACB1 PLLFRACB2 PLLINTC PLLFRACC0 PLLFRACC1 PLLFRACC2 PLLINTD PLLFRACD0 Data Sheet Address 0x00 0x01 0x04 0x05 0x06 0x07 0x08 0x09 0x0A 0x0B 0x0C 0x0D 0x0E 0x0F 0x10 0x11 0x12 0x13 0x14 0x15 0x16 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description PLLFRACD1 PLLFRACD2 SLOPEDIV POWCFG0 POWCFG1 FDEV GFDIV GFXOSC ANTTDCC RES1 VAC0 VAC1 VACERRTH CPCFG PLLBW RES2 ENCCNT PLL fractional division ratio Channel D (byte 1) PLL fractional division ratio Channel D (byte 2) ASK sloping clock divider low PA output power configuration register 0 PA output power configuration register 1 Frequency deviation Gaussian filter divider value Gaussian filter configuration Antenna tuning and Duty Cycle configurations Reserved VAC configuration 0 VAC configuration 1 VCA error threshold Charge pump configuration PLL bandwidth configuration Reserved Encoding start bit counter 0x17 0x18 0x19 0x1A 0x1B 0x1C 0x1D 0x1E 0x1F 0x20 0x21 0x22 0x23 0x24 0x25 0x26 0x27 Data Sheet 65 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description Register address Register name Register-bit position Register-bit command and reset value Register-bit name Register-bits description Registers values Figure 22 Register Terminology Register-bit command terminology r w c read register write register clear-after-write register \0 \0 \0 default to 0 default to 0 default to 0 after clear \1 \1 \1 default to 1 default to 1 default to 1 after clear Important notice: It is mandatory to maintain the default values, as specified in the register tables for all reserved SFRs or reserved bits in SFRs Data Sheet 66 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description Table 4 Register Addr Register Bit Map Configuration Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 SPICHKSUM 0x00 SPICHKSUM SPICHKSUM SPICHKSUM SPICHKSUM SPICHKSUM SPICHKSUM SPICHKSUM SPICHKSUM TXSTAT 0x01 1 n.u. LBD_2V1 LBD_2V4 VAC_FAIL BROUTERR PARERR PLLLDERR TXCFG0 0x04 GO2STDBY reserved reserved FSOFF ISMB ISMB reserved reserved TXCFG1 0x05 GO2SLEEP ASKFSK2 ASKFSK1 ASKSLOPE INVERT ENCMODE ENCMODE ENCMODE CLKOUTCFG 0x06 CLKSRC CLKSRC AFTERSCALE AFTERSCALE PRESCALE PRESCALE PRESCALE CLKOUTENA BDRDIV 0x07 BDRDIV BDRDIV BDRDIV BDRDIV BDRDIV BDRDIV BDRDIV BDRDIV PRBS 0x08 PRBS PRBS PRBS PRBS PRBS PRBS PRBS PRBS n.u. PLLINTA PLLINTA PLLINTA PLLINTA PLLINTA PLLINTA PLLINTA PLLINTA 0x09 PLLFRACA0 0x0A PLLFRACA0 PLLFRACA0 PLLFRACA0 PLLFRACA0 PLLFRACA0 PLLFRACA0 PLLFRACA0 PLLFRACA0 PLLFRACA1 0x0B PLLFRACA1 PLLFRACA1 PLLFRACA1 PLLFRACA1 PLLFRACA1 PLLFRACA1 PLLFRACA1 PLLFRACA1 PLLFRACA2 0x0C n.u. n.u. FRACCOMPA PLLFRACA2 PLLFRACA2 PLLFRACA2 PLLFRACA2 PLLFRACA2 PLLINTB 0x0D n.u. PLLINTB PLLINTB PLLINTB PLLINTB PLLINTB PLLINTB PLLINTB PLLFRACB0 0x0E PLLFRACB0 PLLFRACB0 PLLFRACB0 PLLFRACB0 PLLFRACB0 PLLFRACB0 PLLFRACB0 PLLFRACB0 PLLFRACB1 0x0F PLLFRACB1 PLLFRACB1 PLLFRACB1 PLLFRACB1 PLLFRACB1 PLLFRACB1 PLLFRACB1 PLLFRACB1 PLLFRACB2 0x10 n.u. n.u. FRACCOMPB PLLFRACB2 PLLFRACB2 PLLFRACB2 PLLFRACB2 PLLFRACB2 PLLINTC 0x11 n.u. PLLINTC PLLINTC PLLINTC PLLINTC PLLINTC PLLINTC PLLINTC PLLFRACC0 0x12 PLLFRACC0 PLLFRACC0 PLLFRACC0 PLLFRACC0 PLLFRACC0 PLLFRACC0 PLLFRACC0 PLLFRACC0 PLLFRACC1 0x13 PLLFRACC1 PLLFRACC1 PLLFRACC1 PLLFRACC1 PLLFRACC1 PLLFRACC1 PLLFRACC1 PLLFRACC1 PLLFRACC2 0x14 n.u. n.u. FRACCOMPC PLLFRACC2 PLLFRACC2 PLLFRACC2 PLLFRACC2 PLLFRACC2 PLLINTD 0x15 n.u. PLLINTD PLLINTD PLLINTD PLLINTD PLLINTD PLLINTD PLLINTD PLLFRACD0 0x16 PLLFRACD0 PLLFRACD0 PLLFRACD0 PLLFRACD0 PLLFRACD0 PLLFRACD0 PLLFRACD0 PLLFRACD0 PLLFRACD1 0x17 PLLFRACD1 PLLFRACD1 PLLFRACD1 PLLFRACD1 PLLFRACD1 PLLFRACD1 PLLFRACD1 PLLFRACD1 PLLFRACD2 0x18 n.u. n.u. FRACCOMPD PLLFRACD2 PLLFRACD2 PLLFRACD2 PLLFRACD2 PLLFRACD2 SLOPEDIV SLOPEDIV SLOPEDIV SLOPEDIV SLOPEDIV SLOPEDIV SLOPEDIV 0x19 SLOPEDIV SLOPEDIV POWCFG0 0x1A PA_PS2 PA_PS2 PA_PS2 PA_PS1 PA_PS1 PA_PS1 SLOPEDIV SLOPEDIV POWCFG1 0x1B POUT2 POUT2 POUT2 POUT2 POUT1 POUT1 POUT1 POUT1 FDEV 0x1C FDEVSCALE FDEVSCALE FDEVSCALE FDEV FDEV FDEV FDEV FDEV GFDIV 0x1D GFDIV GFDIV GFDIV GFDIV GFDIV GFDIV GFDIV GFDIV GFXOSC 0x1E FHBLANK reserved reserved reserved GFBYP GFDIV GFDIV GFDIV ANTTDCC 0x1F DCCVBYP DCCDISABLE DCCCONF DCCCONF TUNETOP TUNETOP TUNETOP TUNETOP n.u. reserved reserved reserved reserved reserved reserved reserved RES1 0x20 VAC0 0x21 VAC_CTR VAC_CTR VAC_CTR VAC_CTR VAC_CTR VAC_CTR VAC_CTR VAC_CTR VAC1 0x22 n.u. VAC_NXOSC VAC_NXOSC VAC_NXOSC VAC_NXOSCVAC_NXOSCVAC_NXOSC VAC_CTR reserved reserved reserved reserved reserved reserved reserved RES2 0x23 reserved CPCFG 0x24 n.u. reserved reserved reserved CPTRIM CPTRIM CPTRIM CPTRIM PLLBW 0x25 reserved PLLBWTRIM PLLBWTRIM PLLBWTRIM reserved reserved reserved reserved reserved reserved reserved reserved reserved reserved reserved RES3 0x26 reserved ENCCNT 0x27 ENCCNT ENCCNT ENCCNT ENCCNT ENCCNT ENCCNT ENCCNT ENCCNT Data Sheet 67 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description 2.5.2 SFR Detailed Descriptions SPICHKSUM--SPI Checksum Register Bit 6 c/0 Bit 5 c/0 Bit 4 c/0 Bit 3 c/0 Bit 2 c/0 Bit 1 c/0 Bit 0 c/0 ADDR 0x00 Bit 7 c/0 SPICHKSUM SPICHKSUM SPICHKSUM SPICHKSUM SPICHKSUM SPICHKSUM SPICHKSUM SPICHKSUM Bit <7:0> SPICHKSUM SPICHKSUM SPI checksum bit <7:0> Readout and clear the SPI checksum (8-bits), generated by each write to SFR register ADDR 0x01 Bit 7 1 TXSTAT--Transmitter Status Register Bit 6 n.u. Bit 5 LBD_2V1 Bit 4 LBD_2V4 Bit 3 c/0 Bit 2 c/1 Bit 1 PARERR Bit 0 PLLLDER VAC_FAIL BROUTERR / Bit 7 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 LBD_2V1 LBD_2V4 BROUTERR PARERR PLLLDERR 1 / r/0 r/0 c/0 c/0 Mandatory to keep set (1) battery low detected at 2.1 V battery low detected at 2.4 V Don't care Brown out detector error Parity error PLL lock detector error LBD_2V1 LBD_2V4 reserved BROUTERR PARERR PLLLDER Battery voltage drop below 2.1 V detected if 1 NOTE: bit invalid in standby mode. Battery voltage drop below 2.4 V detected if 1 NOTE: bit invalid in standby mode Brownout error detected if 1 Parity error detected if 1 PLL lock error detected if 1 Data Sheet 68 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x04 Bit 7 GO2STDBY TXCFG0--Transmitter Configuration Register 0 Bit 6 Bit 5 reserved Bit 4 FSOFF Bit 3 ISMB Bit 2 ISMB Bit 1 reserved Bit 0 reserved reserved cw/0 Bit 7 Bit 6 Bit 5 Bit 4 Bit 1 Bit 0 w/0 GO2STDBY reserved reserved FSOFF reserved reserved w/0 w/0 w/0 Go to StandBy Reserved, set 0 w/1 w/1 w/0 Reserved, set to 0 Fail-Safe mechanism turned off RF frequency band bit <1:0> Reserved, set to 1 Reserved, set to 0 Bit <3:2> ISMB GO2STDBY FSOFF ISMB Put the chip in STDBY mode (look at the detailed state diagram), cleared after 1 is written Fail-Safe mechanism 0: on ISM band selection (2-bits) 00: MHz 300-320 01: MHz 425-450 10: MHz 863-870 11: MHz 902-928 1:off For the reserved registers, it is mandatory to retain always the default values. Data Sheet 69 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x05 Bit 7 GO2SLEEP TXCFG1--Transmitter Configuration Register 1 Bit 6 Bit 5 ASKFSK1 Bit 4 ASKSLOPE Bit 3 INVERT Bit 2 w/1 Bit 1 w/0 Bit 0 w/1 ASKFSK2 ENCMODE ENCMODE ENCMODE cw/0 Bit 7 Bit 4 Bit 3 w/0 GO2SLEEP ASKSLOPE INVERT w/1 w/0 w/0 Go to Sleep Bit <6:5> ASKFSK2:1 [ASK / FSK setting 2] and [ASK / FSK setting 1] ASK sloping enable Data inversion Encoding mode bit <2:0> Bit <2:0> ENCMODE GO2SLEEP ASKFSK2:1 Set the chip into SLEEP mode (look at the detailed state diagram), cleared after 1 is written [ASK / FSK modulation switch setting 2] and [ASK / FSK modulation switch setting 1] 0: ASK 1: FSK 1: enable 1: data inverted ASK sloping enable 0: disable Encoded data inversion enable 0: data not inverted Encoding mode, code selection (3 bits) 000: 010: Manchester Biphase Space 011: 001: Differential Biphase Manchester Mark 100: Miller (Delay) 101: NRZ 110: Scrambling (PRBS) 111: not used (data =0) ASKSLOPE INVERT ENCMODE Data Sheet 70 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x06 Bit 7 CLKSRC CLKOUTCFG - Clock Pre- and Post-scaler Bit 6 Bit 5 w/0 Bit 4 w/0 Bit 3 PRESCALE Bit 2 PRESCALE Bit 1 PRESCALE Bit 0 CLKOUTENA CLKSRC AFTERSCALE AFTERSCALE w/0 w/0 w/1 w/0 w/0 w/1 Bit <7:6> CLKSRC Bit <5:4> AFTERSCALE Bit <3:1> PRESCALE Bit 0 CLKSRC CLKOUTENA Clock source selection bit <1:0> Post scaler selection bit <1:0> Pre scaler selection bit <2:0> Enable clock output Clock output selection (2-bits) 00: prescaler clock 01: BDRDIV counter clock 10: inverted BDRDIV counter clock 11: afterscaler clock AFTERSCALE Post-scaler clock divider selection (2 bits) 00: divide by 1 01: divide by 2 10: divide by 4 11: divide by 8 PRESCALE Pre-scaler clock divider selection (3-bits) 000: divide by 1 001: divide by 2 010: divide by 4 011: divide by 8 100: 101: 110: 111: divide by 16 divide by 32 divide by 64 divide by 128 CLKOUTENA Clock output enable 0: disable, instead of clock, the Crystal Oscillator stable signal causes a rising edge on CLKOUT 1: enabled Enabled also automatically, when default clocking (fSYS/16) is used, when the SDI input is low at the rising edge of the EN after power up Data Sheet 71 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x07 Bit 7 BDRDIV BDRDIV--Bit-rate Divider Bit 6 Bit 5 BDRDIV Bit 4 BDRDIV Bit 3 BDRDIV Bit 2 BDRDIV Bit 1 BDRDIV Bit 0 BDRDIV BDRDIV w/1 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:0> BDRDIV BRDRDIV BDRDIV divider bit <7:0> Along with the pre-scaler and the post-scaler, Bit-rate clock divider value (8 bits), defines the data bit-rate, according to following formula. Range: from 0x00: BDRDIV = 0 to 0xFF: BDRDIV = 255 Formula to calculate the bit-rate: f XOSC bitrate = ----------------------------------------------------------------------------------------------------------------------------------PRESCALE x ( BDRDIV + 1 ) x 2 x A FTERSCALE ADDR 0x08 Bit 7 PRBS PRBS--PRBS Start Value Bit 6 PRBS Bit 5 PRBS Bit 4 PRBS Bit 3 PRBS Bit 2 PRBS Bit 1 PRBS Bit 0 PRBS w/1 w/0 w/1 w/0 w/1 w/0 w/1 w/1 Bit <7:0> PRBS PRBS PRBS start value bit <7:0> PRBS start value (8 bits), the PRBS generator uses this as a starting value after each transmission beginning Data Sheet 72 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x09 Bit 7 n.u. PLLINTA--PLL MM Integer Value Channel A Bit 6 Bit 5 PLLINTA Bit 4 PLLINTA Bit 3 PLLINTA Bit 2 PLLINTA Bit 1 PLLINTA Bit 0 PLLINTA PLLINTA / w/1 w/0 w/0 w/0 w/0 w/0 w/0 Bit <6:0> PLLINTA PLLINTA ADDR 0x0A Integer division ratio bit <6:0> Multi-modulus divider integer offset value (7 bits) for Channel A PLLFRACA0--PLL Fractional Division Ratio Channel A (byte 0) Bit 6 w/0 Bit 5 w/0 Bit 4 w/0 Bit 3 w/0 Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 Bit 7 w/0 PLLFRACA0 PLLFRACA0 PLLFRACA0 PLLFRACA0 PLLFRACA0 PLLFRACA0 PLLFRACA0 PLLFRACA0 Bit <7:0> PLLFRACA0 PLLFRACA0 Fractional division ratio bit <7:0> Synthesizer channel frequency value (21 bits, bits < 7:0 >), fractional division ratio for Channel A ADDR 0x0B PLLFRACA1--PLL Fractional Division Ratio Channel A (byte 1) Bit 6 w/0 Bit 5 w/0 Bit 4 w/0 Bit 3 w/0 Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 Bit 7 w/0 PLLFRACA1 PLLFRACA1 PLLFRACA1 PLLFRACA1 PLLFRACA1 PLLFRACA1 PLLFRACA1 PLLFRACA1 Bit <7:0> PLLFRACA1 PLLFRACA1 Fractional division ratio bit <15:8> Synthesizer channel frequency value (21 bits, bits < 15:8 >), fractional division ratio for Channel A Data Sheet 73 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x0C PLLFRACA2--PLL Fractional Division Ratio Channel A (byte 2) Bit 6 n.u. Bit 7 n.u. Bit 5 reserved Bit 4 w/1 Bit 3 w/0 Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 PLLFRACA2 PLLFRACA2 PLLFRACA2 PLLFRACA2 PLLFRACA2 / Bit 5 / reserved w/0 Reserved, set to 0 Fractional division ratio bit <20:16> Bit <4:0> PLLFRACA2 PLLFRACA2 Synthesizer channel frequency value (21 bits, bits < 20:16 >), fractional division ratio for Channel A ADDR 0x0D Bit 7 n.u. PLLINTB--PLL MM Integer Value Channel B Bit 6 Bit 5 PLLINTB Bit 4 PLLINTB Bit 3 PLLINTB Bit 2 PLLINTB Bit 1 PLLINTB Bit 0 PLLINTB PLLINTB / w/1 w/0 w/0 w/0 w/0 w/0 w/0 Bit <6:0> PLLINTB PLLINTB ADDR 0x0E Integer division ratio bit <6:0> Multi-modulus divider integer offset value (7 bits) for Channel B PLLFRACB0--PLL Fractional Division Ratio Channel B (byte 0) Bit 6 w/0 Bit 5 w/0 Bit 4 w/0 Bit 3 w/0 Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 Bit 7 w/0 PLLFRACB0 PLLFRACB0 PLLFRACB0 PLLFRACB0 PLLFRACB0 PLLFRACB0 PLLFRACB0 PLLFRACB0 Bit <7:0> PLLFRACB0 PLLFRACB0 Fractional division ratio bit <7:0> Synthesizer channel frequency value (21 bits, bits < 7:0 >), fractional division ratio for Channel B Data Sheet 74 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x0F PLLFRACB1--PLL Fractional Division Ratio Channel B (byte 1) Bit 6 w/0 Bit 5 w/0 Bit 4 w/0 Bit 3 w/0 Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 Bit 7 w/0 PLLFRACB1 PLLFRACB1 PLLFRACB1 PLLFRACB1 PLLFRACB1 PLLFRACB1 PLLFRACB1 PLLFRACB1 Bit <7:0> PLLFRACB1 PLLFRACB1 Fractional division ratio bit <15:8> Synthesizer channel frequency value (21 bits, bits < 15:8 >), fractional division ratio for Channel B ADDR 0x10 PLLFRACB2--PLL Fractional Division Ratio Channel B (byte 2) Bit 6 n.u. Bit 7 n.u. Bit 5 reserved Bit 4 w/1 Bit 3 w/0 Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 PLLFRACB2 PLLFRACB2 PLLFRACB2 PLLFRACB2 PLLFRACB2 / Bit 5 / reserved w/0 Reserved, set to 0 Fractional division ratio bit <20:16> Bit <4:0> PLLFRACB2 PLLFRACB2 Synthesizer channel frequency value (21 bits, bits < 20:16 >), fractional division ratio for Channel B ADDR 0x11 Bit 7 n.u. PLLINTC--PLL MM Integer Value Channel C Bit 6 Bit 5 PLLINTC Bit 4 PLLINTC Bit 3 PLLINTC Bit 2 PLLINTC Bit 1 PLLINTC Bit 0 PLLINTC PLLINTC / w/1 w/0 w/0 w/0 w/0 w/0 w/0 Bit <6:0> PLLINTC PLLINTC Integer division ratio bit <6:0> Multi-modulus divider integer offset value (7 bits) for Channel C Data Sheet 75 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x12 PLLFRACC0--PLL Fractional Division Ratio Channel C (byte 0) Bit 6 w/0 Bit 5 w/0 Bit 4 w/0 Bit 3 w/0 Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 Bit 7 w/0 PLLFRACC0 PLLFRACC0 PLLFRACC0 PLLFRACC0 PLLFRACC0 PLLFRACC0 PLLFRACC0 PLLFRACC0 Bit <7:0> PLLFRACC0 PLLFRACC0 Fractional division ratio bit <7:0> Synthesizer channel frequency value (21 bits, bits < 7:0 >), fractional division ratio for Channel C ADDR 0x13 PLLFRACC1--PLL Fractional Division Ratio Channel C (byte 1) Bit 6 w/0 Bit 5 w/0 Bit 4 w/0 Bit 3 w/0 Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 Bit 7 w/0 PLLFRACC1 PLLFRACC1 PLLFRACC1 PLLFRACC1 PLLFRACC1 PLLFRACC1 PLLFRACC1 PLLFRACC1 Bit <7:0> PLLFRACC1 PLLFRACC1 Factional division ratio bit <15:8> Synthesizer channel frequency value (21 bits, bits < 15:8 >), fractional division ratio for Channel C Data Sheet 76 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x14 PLLFRACC2--PLL Fractional Division Ratio Channel C (byte 2) Bit 6 n.u. Bit 7 n.u. Bit 5 reserved Bit 4 w/1 Bit 3 w/0 Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 PLLFRACC2 PLLFRACC2 PLLFRACC2 PLLFRACC2 PLLFRACC2 / Bit 5 / reserved w/0 Reserved, set to 0 Factional division ratio bit <20:16> Bit <4:0> PLLFRACC2 PLLFRACC2 Synthesizer channel frequency value (21 bits, bits < 20:16 >), fractional division ratio for Channel C ADDR 0x15 Bit 7 n.u. PLLINTD--PLL MM Integer Value Channel D Bit 6 Bit 5 PLLINTD Bit 4 PLLINTD Bit 3 PLLINTD Bit 2 PLLINTD Bit 1 PLLINTD Bit 0 PLLINTD PLLINTD / w/1 w/0 w/0 w/0 w/0 w/0 w/0 Bit <6:0> PLLINTD PLLINTD ADDR 0x16 Integer division ratio bit <6:0> Multi-modulus divider integer offset value (7 bits) for Channel D PLLFRACD0--PLL Fractional Division Ratio Channel D (byte 0) Bit 6 w/0 Bit 5 w/0 Bit 4 w/0 Bit 3 w/0 Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 Bit 7 w/0 PLLFRACD0 PLLFRACD0 PLLFRACD0 PLLFRACD0 PLLFRACD0 PLLFRACD0 PLLFRACD0 PLLFRACD0 Bit <7:0> PLLFRACD0 PLLFRACD0 Fractional division ratio bit <7:0> Synthesizer channel frequency value (21 bits, bits < 7:0 >), fractional division ratio for Channel D Data Sheet 77 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x17 PLLFRACD1--PLL Fractional Division Ratio Channel D (byte 1) Bit 6 w/0 Bit 5 w/0 Bit 4 w/0 Bit 3 w/0 Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 Bit 7 w/0 PLLFRACD1 PLLFRACD1 PLLFRACD1 PLLFRACD1 PLLFRACD1 PLLFRACD1 PLLFRACD1 PLLFRACD1 Bit <7:0> PLLFRACD1 PLLFRACD1 Fractional division ratio bit <15:8> Synthesizer channel frequency value (21 bits, bits < 15:8 >), fractional division ratio for Channel D ADDR 0x18 PLLFRACD2--PLL Fractional Division Ratio Channel D (byte 2) Bit 6 n.u. Bit 7 n.u. Bit 5 reserved Bit 4 w/1 Bit 3 w/0 Reserved Bit 2 w/0 Bit 1 w/0 Bit 0 w/0 PLLFRACD2 PLLFRACD2 PLLFRACD2 PLLFRACD2 PLLFRACD2 / Bit 5 / reserved w/0 Bit <4:0> PLLFRACD2 PLLFRACD2 Fractional division ratio bit <20:16> Synthesizer channel frequency value (21 bits, bits < 20:16 >), fractional division ratio for Channel D Data Sheet 78 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x19 Bit 7 SLOPEDIV SLOPEDIV --ASK Sloping Clock Divider Bit 6 Bit 5 SLOPEDIV Bit 4 SLOPEDIV Bit 3 SLOPEDIV Bit 2 SLOPEDIV Bit 1 SLOPEDIV Bit 0 SLOPEDIV SLOPEDIV w/1 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:0> SLOPEDIV SLOPEDIV ASK sloping clock divider bit <7:0> ASK sloping clock division ratio (10 bits, bits < 7:0 >), defines the slope of the ASK signal shaping using PA power stage switching Range: from 0x000: SLOPEDIV = 1 to 0x3FF: SLOPEDIV = 1024 ADDR 0x1A Bit 7 PA_PS2 POWCFG0--PA Output Power Configuration Register 0 Bit 6 Bit 5 PA_PS2 Bit 4 PA_PS1 Bit 3 PA_PS1 Bit 2 PA_PS1 Bit 1 SLOPEDIV Bit 0 SLOPEDIV PA_PS2 w/0 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:5> PA_PS2 Bit <4:2> PA_PS1 Bit <1:0> SLOPEDIV PA_PS2 PA output blocks setting 2 bit <2:0> PA output blocks setting 1 bit <2:0> ASK sloping clock divider bit <9:8> Individual control of the 3 PA blocks, setting 2 (3-bits) 0: disabled 1: enabled Bit(0) ==> PA block 0 Bit(0) ==> PA block 0 Bit(1) ==> PA block 1 Bit(1) ==> PA block 1 Bit(2) ==> PA block 2 Bit(2) ==> PA block 2 PA_PS1 Individual control of the 3 PA blocks, setting 1(3-bits) 0: disabled 1: enabled SLOPEDIV ASK sloping clock division ratio (10 bits, bits < 9:8 >), defines the frequency of the ASK signal shaping using PA power stage switching Range: from 0x000: SLOPEDIV = 1 to 0x3FF: SLOPEDIV = 1024 Data Sheet 79 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x1B Bit 7 POUT2 POWCFG1--PA Output Power Configuration Register 1 Bit 6 Bit 5 POUT2 Bit 4 POUT2 Bit 3 POUT1 Bit 2 POUT1 Bit 1 POUT1 Bit 0 POUT1 POUT2 w/0 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:4> POUT2 Bit <3:0> POUT1 POUT2 Output power setting 2 bit <3:0> Output power setting 1 bit <3:0> PA output power setting 2 (4 bits), defines the number of enabled PA stages Range: from 0x0: POUT2 = 0 to 0xB: POUT2 = 11 > 0xB: POUT2 = 11 to 0xB: POUT1 = 11 > 0xB: POUT1 = 11 POUT1 PA output power setting 1 (4 bits), defines the number of enabled PA stages Range: from 0x0: POUT1 = 0 Data Sheet 80 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x1C Bit 7 FDEVSCALE FDEV--Frequency Deviation Bit 6 Bit 5 FDEVSCALE Bit 4 FDEV Bit 3 FDEV Bit 2 FDEV Bit 1 FDEV Bit 0 FDEV FDEVSCALE w/1 w/1 w/0 w/1 w/1 w/1 w/1 w/1 Bit <7:5> FDEVSCALE Bit <4:0> FDEV FDEVSCALE Frequency deviation scaling bit <2:0> Frequency deviation bit <4:0> Scaling of the frequency deviation (3 bits) 000: 001: 010: 011: divide by 64 divide by 32 divide by 16 divide by 8 100: divide by 4 101: divide by 2 110: divide by 1 value = ----------------------------111: 64 multiply by2 2 FDEVSCALE FDEV Frequency deviation value (5 bits), defines the multiplication value for the output data from the Gaussian filter (0-31) Data Sheet 81 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x1D Bit 7 GFDIV GFDIV--Gaussian Filter Divider Value Bit 6 Bit 5 GFDIV Bit 4 GFDIV Bit 3 GFDIV Bit 2 GFDIV Bit 1 GFDIV Bit 0 GFDIV GFDIV w/0 w/0 w/0 w/0 w/1 w/0 w/0 w/0 Bit <7:0> GFDIV GFDIV Gaussian filter divider bit <7:0> Gaussian filter clock divider value (11 bits, bits < 7:0 >), defines the sampling ratio of the Gaussian filter; typically this value is set such that the GF divider NGF is 16 x chip-rate (for ideal Gaussian filtering) f XOSC GFDIV = ---------------------------------------- - 1 chiprate x NGF Note: it is recommended to program the GFDIV register in such way, that the GF divider NGF is 16 times the chip-rate. This allows optimum Gaussian filtering. Data Sheet 82 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x1E Bit 7 FHBLANK GFXOSC--Gaussian Filter Configuration Bit 6 Bit 5 reserved Bit 4 reserved Bit 3 GFBYP Bit 2 GFDIV Bit 1 GFDIV Bit 0 GFDIV reserved w/0 Bit 7 Bit 3 w/1 FHBLANK GFBYP w/1 w/1 w/1 w/0 w/0 w/0 Frequency Hopping VAC Disable Reserved, set all bits to 1 Gaussian filter bypass Gaussian filter divider bits <10:8> Bit <6:4> reserved Bit <2:0> GFDIV FHBLANK Frequency Hopping, enable/disable VCO Auto Calibration for Channel Hopping 0: enable VCO Auto Calibration (default) 1: Skip VCO Auto Calibration for frequency hops <1MHz 1: GF bypassed GFBYP GFDIV Gaussian filter bypass: 0: GF enabled Gaussian filter clock divider value (11 bits, bits < 10:8 >), defines the sampling ratio of the Gaussian filter, typically this value is set such that the GF divider is 16 x chiprate (for ideal Gaussian filtering) f XOSC GFDIV = ---------------------------------- - 1 chiprate x 16 Data Sheet 83 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x1F ANTTDCC--Antenna Tuning and Duty Cycle Configurations Bit 6 DCC DISABLE Bit 7 reserved Bit 5 DCCCONF Bit 4 DCCCONF Bit 3 TUNETOP Bit 2 TUNETOP Bit 1 TUNETOP Bit 0 TUNETOP w/0 Bit 7 Bit 6 Bit 3:0 w/0 reserved w/1 w/0 w/0 w/0 w/0 w/0 Reserved, set to 0 Duty cycle control disable Duty cycle control delay configuration bit <1:0> Antenna tuning top (PAOUT pin) bit <3:0> DCCDISABLE TUNETOP Bit <5:4> DCCCONF DCCDISABLE DCCCONF Duty cycle control disable (must be 0 for ISMB=0) 0 enabled 00: 43% (69/35/33 ps) 01: 39% (207/104/9 8 ps) 10: 35% (346/173/ 164 ps) 1 disabled (delay = 0ps) 11: 31% (484/242/ 230 ps) Duty cycle control delay configuration (ISMB = 1/2/3, for ISMB = 0 => delay = 0 ps) TUNETOP Antenna tuning top capacitor selection (4-bits): Individual switch of capacitor banks Bit(0) ==> 60 fF Bit(1) ==> 120 fF 0: switched off Bit(2) ==> 240 fF Bit(3) ==> 480 fF 1: switched on ADDR 0x20 Bit 7 n.u. RES1--Reserved Bit 6 Bit 5 reserved Bit 4 reserved Bit 3 reserved Bit 2 reserved Bit 1 reserved Bit 0 reserved reserved / Bit <7:0> w/1 w/0 w/0 w/1 w/1 w/0 w/0 reserved Reserved, set bits <6,3,2> to 1 and bits <5, 4, 1, 0> to 0 Data Sheet 84 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description . ADDR 0x21 Bit 7 VAC_CTR VAC0--VAC Configuration 0 Bit 6 Bit 5 VAC_CTR Bit 4 VAC_CTR Bit 3 VAC_CTR Bit 2 VAC_CTR Bit 1 VAC_CTR Bit 0 VAC_CTR VAC_CTR w/1 w/1 w/0 w/0 w/1 w/0 w/0 w/0 Bit <7:0> VAC_CTR VAC_CTR ADDR 0x22 Bit 7 n.u. VAC frequency counter value bit <7:0> VCO autocalibration FAST counter (~100 MHz) compare value (9 bits, bits< 7:0 >) VAC1--VAC Configuration 1 Bit 6 Bit 5 reserved Bit 4 reserved Bit 3 reserved Bit 2 reserved Bit 1 reserved Bit 0 VAC_CTR reserved / Bit 7 Bit 0 VAC_CTR . ADDR 0x23 Bit 7 reserved w/1 n.u. VAC_CTR w/0 w/0 w/0 Not used w/0 w/0 w/0 Bit <6:1> reserved Reserved, set bit 6 to 1, bits <5:1> to 0 VAC frequency counter value bit 8 VCO autocalibration FAST counter (~100 MHz) compare value (9 bits, bit 8) RES2 Bit 6 Bit 5 reserved Bit 4 reserved Bit 3 reserved Bit 2 reserved Bit 1 reserved Bit 0 reserved reserved w/0 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:0> reserved Reserved, set to 0 Data Sheet 85 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description ADDR 0x24 Bit 7 n.u. CPCFG--Charge Pump Configurations Bit 6 Bit 5 reserved Bit 4 reserved Bit 3 CPTRIM Bit 2 CPTRIM Bit 1 CPTRIM Bit 0 CPTRIM reserved / w/0 w/1 w/0 w/0 Reserved w/1 w/0 w/0 Bit <6:4> reserved Bit <3:0> CPTRIM CPTRIM Charge pump current trimming bit <3:0> Charge pump current trimming (4-bits): Range: from 0x00: current = 2.5 A to 0xF. current = 40 A step: 2.5 A Note: CPTRIM bits must be set correlated with PLLBW bits, otherwise loop instability may occur ADDR 0x25 Bit 7 reserved PLLBW-- PLL Bandwidth Configuration Bit 6 Bit 5 PLLBW TRIM Bit 4 PLLBW TRIM Bit 3 reserved Bit 2 reserved Bit 1 reserved Bit 0 reserved PLLBW TRIM w/1 Bit 7 w/1 reserved w/0 w/1 w/1 reserved w/0 w/0 w/0 Bit <6:4> PLLBWTRIM Bit <3:0> reserved PLLBWTRIM Trim bandwidth of the PLL loop filter bit <2:0> reserved Trim bandwidth of the PLL loop filter (3 bits): Range: from 0x0: BW = 300 kHz to 0x7: BW = 90 kHz step: 30 kHz Note: PLLBW must be set together with CPTRIM according to following table: PLLBWTRIM [kHz] CPTRIM [A] 90 5 120 7.5 150 12.5 180 17.5 210 25 240 32.5 270 40 Data Sheet 86 V 1.0, July 2009 TDA 5150 TDA 5150 Functional Description . ADDR 0x26 Bit 7 reserved RES3--Reserved Bit 6 Bit 5 reserved Bit 4 reserved Bit 3 reserved Bit 2 reserved Bit 1 reserved Bit 0 reserved reserved w/1 Bit <7:0> w/1 w/0 w/0 w/0 w/0 w/0 w/0 reserved Reserved, set bits <7:6> to 1, and bits <5:0> to 0 . ADDR 0x27 Bit 7 ENCCNT ENCCNT - Encoding start bit counter Bit 6 Bit 5 ENCCNT Bit 4 ENCCNT Bit 3 ENCCNT Bit 2 ENCCNT Bit 1 ENCCNT Bit 0 ENCCNT ENCCNT w/0 w/0 w/0 w/0 w/0 w/0 w/0 w/0 Bit <7:0> ENCCNT ENCCNT Encoding start bit counter bit <7:0> Sets the number of bits on start of a telegram which shall be sent unencoded or unscrambled before encoder/scrambler is switched on. This feature is used e.g. to be able to send unscrambled synchronization patterns first. Data Sheet 87 V 1.0, July 2009 TDA 5150 Applications 3 3.1 Applications Simple application schematics example L1 100 nH Antenna C clocked by TDA 5150 SPI bus controlled by C VBAT SDIO SCK EN SDIO SCK EN CLKOUT XTAL GND C1 8.2 pF Q1 13.00 MHz VREG C2 100 nF C6 100 nF VBAT PAOUT C XTAL / TIM / IRQ TDA 5150 GNDPA GND C3 10 pF* C4 5 pF* Remarks: * values valid for 433 MHz and the given antenna geometry TDA 5150 EN XTAL 1 2 3 4 5 VREG PLL XOSC SPI SFR 10 9 8 7 6 SDIO/DATA SCK CLKOUT GNDPA PAOUT 3.0mm GND VREG VBAT PA+ ANT_TUNE 3.0mm 4.9mm Figure 23 Simple application example with reduced Bill of Materials Data Sheet 88 V 1.0, July 2009 3.2 Figure 24 GND X7 GND GND GND 1 2 3 4 5 EN XTAL GND VREG VBAT SDIO/DATA SCK CLKOUT GNDPA PAOUT 10 9 8 7 6 V_BAT C7 100n R4 JP3 JP4 GND GND GND GND C5 100n 100p GND GND RT_Test GND GND C1 L3 GND GND JP2 L2 L1 C3 C2 X1 RF OUT C10 X6 Infineon Evaluation Board V1.1 1 3 5 7 GND 9 11 13 15 17 19 21 23 25 27 29 31 EN 33 SDIO 35 SCK 37 39 CLKOUT 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 I_VBat C4 X8 1 2 3 4 5 6 GND GND VCC C8 100n + Ext Supply GND GND X3_1 X3_2 Infineon Evaluation Board schematics (E.B. V1.1 board version) C6 8.2 pF Q1 V 1.0, July 2009 TDA 5150 Applications GND JP1 VBAT SEL C9 Match In Data Sheet EN SDIO SCK CLKOUT V_BAT 8 7 6 5 4 3 2 1 GND GNDGND R1 X2 89 TDA 5150 Applications Figure 25 Component placement on Infineon Evaluation Board (V1.1, top side) Data Sheet 90 V 1.0, July 2009 TDA 5150 Applications Figure 26 Infineon Evaluation Board V1.1 top side, copper layer Data Sheet 91 V 1.0, July 2009 TDA 5150 Applications Figure 27 Infineon Evaluation Board V1.1 top side, solder mask Data Sheet 92 V 1.0, July 2009 TDA 5150 Applications Figure 28 Infineon Evaluation Board V1.1 bottom side, copper layer Data Sheet 93 V 1.0, July 2009 TDA 5150 Applications Figure 29 Infineon Evaluation Board V1.1 bottom side, solder mask Data Sheet 94 V 1.0, July 2009 TDA 5150 Applications Figure 30 Infineon Evaluation Board V1.1 drill map and tool list Data Sheet 95 V 1.0, July 2009 TDA 5150 Applications TDA5150 see Table 6 see Table 6 see Table 6 see Table 6 see Table 6 see Table 6 see Table 6 Table 5 Bill of Materials, Infineon Evaluation Board V1.1 Note: frequency dependent component values (PA matching network for instance) are listed in Table 6 Table 6 Frequency band dependent component values Data Sheet 96 V 1.0, July 2009 TDA 5150 Electrical Characteristics 4 4.1 Electrical Characteristics Absolute Maximum Ratings Attention: Stresses above the maximum values listed below may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Maximum ratings are absolute ratings; exceeding only one of these values may cause irreversible damage to the integrated circuit. Table 7 Absolute Maximum Ratings Symbol min. A1 A2 Supply voltage Junction Temperature VBAT Tj -0.3 -40 -40 Values max. +4 +150 V 1) Max. 24 hrs. by Tmax. accumulated over lifetime 2)VBAT =3,6V Max 1000 hours by Tmax or Tmin Max 180 sec, 10 x Tcycles over lifetime. Acc. to JEDEC EIA /JESD22A114-B Acc. to JEDEC EIA /JESD22A114-B All pins except corner pins All corner pins AEC-Q100 (transient current) +125 C Unit Note/ Test Condition Parameter A3 A4 Storage Temperature Transient Temperature Ts Ttran -50 - +150 C +175 C A5 ESD HBM integrity VHBM (all pins except pin 6, RF-PA output) ESD HBM integrity (pin 6) ESD SDM integrity VHBMRF -4 - +4 kV A6 -4 - +4 kV A7 VSDM -500 -750 - +500 V +750 V mA A8 Latch up ILU 100 Data Sheet 97 V 1.0, July 2009 TDA 5150 Electrical Characteristics Parameter A9 Maximum Input Voltage @ digital input pins Symbol min. Vin -0.3 Values max. VBAT V + 0.3 4 mA Note 1 Unit Note/ Test Condition IIOmax A10 Maximum Current into digital input and output pins A11 Maximum Input VIn,XTAL Voltage @ XTAL pin (pin 2) -0,3 - VREG + 0.3 Note 2 Note1: It is not allowed to apply higher voltages than specified by A9, even if current is limited to values below A10. The voltage limiting effect of the internal ESD structures must not be used as "level shifter" by interconnection(s) to digital logic with higher output voltage! Note2: VREG is the output voltage of the internal voltage regulator, accessible on pin 4, (VREG). 4.2 Table 8 Operating Range Supply Voltage Operating Range and Temperature Operating Range Symbol min. VBAT Tamb 1.9 -40 Values typ max. 3.6 +85 V C Unit Note/ Test Condition [-40..+85]C Parameter B1 B2 Supply Voltage Operating Temperature Data Sheet 98 V 1.0, July 2009 TDA 5150 Electrical Characteristics 4.2.1 AC/DC Characteristics Supply voltage VBAT = 1.9V ... 3.6V; Ambient temperature Tamb =[-40...+85] oC, unless otherwise specified. Maximum 10 pF capacitive load at CLKOUT (pin 8). Frequency of clock on CLKOUT (pin 8), fCLKOUT = fXTAL / 16. Attention: Test means that the parameter is not subject to production test. It was verified by design and/or characterization. Table 9 AC/DC Characteristics Symbol fTX Limit Values min C1 Transmit Frequency Bands Modulation Types Encoding Modes Chip Rate 300 425 863 typ max 320 450 928 MHz MHz MHz Unit Test Conditions Remarks Pin # Parameter C2 C3 C4 ASK (OOK), FSK(CPFSK), GFSK Manchester, differential Manchester, Miller, Biphase-mark, Biphase-space, scrambled NRZ 0.5 100 kchip/s See Chapter 2.4.4 for chip rate definition Hz kHz fXTAL / 2exp(21) See Chapter 2.4.7 for frequency shift calculation Total max. cap. (including parasitics) C5 C6 Carrier fstep Frequency Step Frequency Deviation (Programmable) 7 1 64 fdev C7 Crystal Frequency Range fXTAL 12 14 MHz between XTAL (pin2) and GND max. 4 pF RSTART 1) |-500| LOSC tXTAL 3.85 5.5 1 Ohm 7.15 H ms 1)fcrystal = 13,56 MHz Tamb = 25 C with crystal C8 C9 Crystal Osc Margin XTAL Startup Time NDK NX5032SA on TDA5150 Evaluation Board Data Sheet 99 V 1.0, July 2009 TDA 5150 Electrical Characteristics Pin # Parameter C10 CLKOUT Output Frequency C11 Voltage Regulator Output Voltage Symbol f CLKOUT Limit Values min typ max 14 MHz Unit Test Conditions Remarks For divider ratio calculations see Chapter 2.4.5.1 100 nF decoupling on VREG pin. No external DC load allowed 1)VBAT =3V@27C 2)VBAT > 2.2 V for effective regulator operation 1)by T=27C 2)by Tmax=85C 1)by T=27C 2)by Tmax=85C monitored @VBAT VREG 2.11) 2) V C12 Supply Current Sleep Mode C13 Supply Current Standby Mode C14 Low-Battery Detector Threshold C15 Brownout Detector Voltage Threshold Isleep Istandby VLBD_2.1 VLBD_2.4 VBOD VBOD 2.0 2.3 1.7 0.7 0.41) 2.52) A 0.51) 62) 2.2 2.5 1.8 1.7 A V V V V in Active Mode monitored @VREG in Standby Mode monitored @VREG and @VBAT VBAT =3V C16 Supply Current Ipllenable PLL is ON PA is OFF @315/434 MHz C17 Supply Current PLL is ON PA is OFF @868/915MHz Ipllenable 6,3 8 mA 6,6 8,5 mA VBAT =3V C18 Supply Current IT5dbm Transmit Mode I T8dbm @315/434 MHz IT10dbm 9 11 13 12 14 16 mA mA mA 1) 1)@Pout=5/8/10 2) 50 Ohms load dBm measured with 2)VBAT =3V Data Sheet 100 V 1.0, July 2009 TDA 5150 Electrical Characteristics Pin # Parameter Symbol Limit Values min C19 Supply Current IT5dbm Transmit Mode I T8dbm @868/915 MHz IT10dbm C20 Power Level Tolerance vs. nominal value Pvar5dbm Pvar8dbm Pvar10dbm Pvar5dbm Pvar8dbm Pvar10dbm C21 Power Level Variation vs. temperature C22 Power Level Variation vs. battery voltage C23 Power Level Step Size C24 PLL bandwidth Pvar5dbm Pvar8dbm Pvar5dbm Pvar8dbm Pvar10dbm Pdelta step 1 1501) -1.5 -1.5 +1.5 dB +1.5 dB +1.5 dB 5.5 5.5 5.5 2 7 7 7 3 dB dB dB dB -2 +2 dB -1.5 typ 11 13 16 max 14 16 19 mA mA mA Unit Test Conditions Remarks 1) 1)@Pout=5/8/10 dB 2) Ohms load 1) m measured into 50 2) VBAT=3V Referenced to +1.5 dB 1) 1) 2) 2) 2) VBAT=3V @27C (not including matching network comp. tolerance) 1)315 & 434 MHz band 2)868 & 915 MHz band Pvar10dbm -1.5 Tamb =[-40..+85]C VBAT= 3 Volt RF Po measured on Evaluation Board VBAT=[1.9...3.6] V RF Po measured on IFX Evaluation Boards maximum 10 steps 1) the PLL BW is 4101) kHz programable. SFR CPTRIM (0x24.3:0) controls the chargepump current and SFR PLLBW TRIM (0x25.6:4)fis the selector for loop filter damping resistor value 150 kHz is the smallest and 410 kHz the largest nominal PLL BW. See Table2 for PLL recommended settings Data Sheet 101 V 1.0, July 2009 TDA 5150 Electrical Characteristics Pin # Parameter Symbol Limit Values min C25 Band Switching tbandswitch Time C26 Channel Switching Time C27 SSB Phase Noise @ 315/434 MHz PLLBW = 150 kHz tchswitch 20 -86 -86 -80 -80 typ max 100 us Unit Test Conditions Remarks jump between band end frequencies [fmin .. fmax] 1 MHz hop away from adj. channel @ 10 kHz offset, +27C @ 100 kHz offset, +27C us dBc/Hz dBc/Hz -105 -100 dBc/Hz @ 1 MHz offset, +27C -135 120 dBc/Hz @ 10 MHz offset, +27C dBc/Hz dBc/Hz @ 10 kHz offset, +27C @ 100 kHz offset, +27C C28 SSB Phase Noise @ 868/915MHz PLLBW = 150 kHz -80 -80 -75 -75 -105 -100 dBc/Hz @ 1 MHz offset, +27C -135 -120 dBc/Hz @ 10 MHz offset, +27C Data Sheet 102 V 1.0, July 2009 TDA 5150 Electrical Characteristics 4.3 SPI Characteristics Attention: Test means that the parameter is not subject to production test. It was verified by design and/or characterization. Table 10 SPI Timing Characteristics Symbol min Values typ max 2 150 150 20 20 20 20 150 50 50 150 MHz ns ns ns ns ns ns ns ns ns ns Unit Note/ Test Condition Parameter D1 D2 D3 D4 D5 D6 D7 D8 D9 Clock Frequency fc Clock High Time tCH Clock Low Time tCL Active SetUp Time tSSu Not Active Hold tEN Time Active Hold Time Not Active SetUp Time Deselect Time Input Data SetUp Time tSHo tNEN tDS tIDSu D10 Input Data Hold tIDHo Time D11 Clock to Output Data Valid @ tCODV 20pF Load D12 Output Data Rise Time @ 20pF Load tODri 25 ns D13 Output Data Fall Time @ 20pF tODfa Load 25 ns Data Sheet 103 V 1.0, July 2009 TDA 5150 Electrical Characteristics Parameter D14 Input Data Tristate Setup Time D15 Output Data Disable Time Table 11 Symbol min tIDZSu tNODZ 0 150 Values typ max ns ns Unit Note/ Test Condition SPI Electrical Characteristics Symbol min Values typ max 0.4 V Unit Note/ Test Condition Pins EN, SCK, SDIO Pins EN, SCK, SDIO Pins SDIO, CLKOUT Pins SDIO, CLKOUT Parameter E1 E2 E3 E4 E5 E6 Input Low Voltage Input High Voltage Output Low Voltage Output High Voltage Parasitic capacitance Internal Pulldown Resistor VIL VIH VOH VOH Cpad Rdown -0.2 VBAT 0.4 VBAT V + 0.2 0.5 V V 5 pF kOhm VBAT 0.5 175 250 360 Data Sheet 104 V 1.0, July 2009 TDA 5150 Package Outline 5 Package Outline 0.1 MAX. 1.05 MAX. 0.1 STANDOFF ST 0.85 0.09 GAUGE PLANE 0.5 0.22 + 0.05 A 0.08 M 0.1A ABC (0.33) 0.42 4.9 +0.15 -0 .1 Marking 10 1 6 5 C 3 + 0.11) Index 0.25 A B C Notes: All dimensions are in mm . 1) Does not include plastic or metal protrusion of max 0.15 mm per side . 2) Does not include plastic or metal protrusion of max 0.25 mm per side . Figure 31 Green Package TSSOP-10 outline 0.3 5.5 3.5 0.5 HLG09617 Figure 32 Footprint TSSOP-10 package You can find all of our packages, types of packing and other information on the Infineon Internet Page "Products":http://www.infineon.com/products SMD = Surface Mounted Device Data Sheet 105 V 1.0, July 2009 6 MAX. H 3 0.1 2) B 0.125+0.08 -0.05 www.infineon.com Published by Infineon Technologies AG |
Price & Availability of TDA5150 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |