 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Product Specification: SP0103 Series with Integrated Amplifier This document applies the following SiSonic Model Numbers: SP0103NC3-2 SP0103NC3-3 SiSonic microphone with integrated amplifier offers designers numerous features: up to 20dB gain, surface-mountable, compatible with standard solder reflow, pick-and-place with standard high speed automated equipment, low output impedance, and excellent environmental characteristics. External amplifiers amplify both signal and external noise induced in the circuit, compared to SiSonic SP0103 that amplifies the signal prior to external noise. Microphone Dimensional Layout Item Height Length Width Weight Coplanarity Dim. 1.45 6.15 3.76 ~0.09 < 0.1 Tol. (+/) 0.15 0.05 0.05 grams Unit mm mm mm mm Microphone Pin Output Recommended PCB Land Layout Knowles Acoustics www.knowlesacoustics.com Rev H SP0103NC3 Product Specifications Test Conditions: +20C, 60-70% R.H. Limits Symbol Condition Min. Nom. Max. Unit Directivity Sensitivity Output impedance Current Consumption Signal to Noise Ratio Typical Input Referred Noise Supply Voltage Sensitivity Loss across Voltage Maximum Input Sound Level S ZOUT IDSS S/N ENL Vs Omni-directional @ 1kHz (0dB=1V/Pa) where R3=0, C1=0.47uF @ 1kHz (0dB=1V/Pa) across 1.5 to 5.5 volts @ 1kHz (0dB=1V/Pa) A-weighted 1.5 Change in sensitivity over 5.5v to 1.5v 0.100 55 59 35 5.5 -26 -22 -18 100 0.350 dB mA dB dBA SPL V dB dB No Change Across Voltage Range At 100dB SPL, THD < 1% At 115dB SPL, THD < 10% -40 -40 100 - 10,000 +100 +100 Operating Temperature Storage Temperature Frequency Range C C Hz Frequency Response Curve Knowles Acoustics www.knowlesacoustics.com Rev H SP0103NC3 Packaging Specifications Carrier - Tape Detail Model Number SP0103NC3 SP0103NC3 Suffix -2 -3 Reel Diameter 7" 13" Qty per Reel 1,200 4,500 Tape & Reel Leader Length Label Storage Life Polarity of part Available in 7" or 13" diameter. 800mm or minimum of 100 empty pockets Label applied to external package and direct to reel. Per JEDEC. 1 year storage (original packaging, low humidity) "L" - direction NOTE: All devices are lead-free and compatible with lead-free reflow profile. Solderability Characteristics Solder Reflow Conditions: 260C for maximum 30 seconds Do not board wash after reflow. Do not pull vacuum directly over acoustic port hole. Reflow Profile (Maximum Conditions) Knowles Acoustics www.knowlesacoustics.com Rev H SP0103NC3 Reliability Note: After test conditions are performed, the sensitivity of the microphone shall not deviate more than 3dB from its initial value. Thermal Shock High Temperature Storage Test Low Temperature Storage Test High Temperature Operating Test Low Temperature Operating Test Humidity Test Vibration Test Microphone unit must operate when exposed to air-to-air thermal shock 100 cycles, from -40C to +125C. (IEC 68-2-4) Microphone unit must maintain sensitivity after storage at +105C for 1,000 hours. (IEC 68-2-2 Test Ba) Microphone unit must maintain sensitivity after storage at -40C for 1,000 hours. (IEC 68-2-1 Test Aa) Microphone unit must operate within sensitivity specifications for 16 hours at 105C. (IEC 68-2-2 Test Ba) Microphone unit must operate within sensitivity specifications for 16 hours at -40C. (IEC 68-2-1 Test Aa) Tested under Bias at 85C/85% R.H. for 270 hours. (JESD22-A101A-B) Microphone unit must operate under test condition: 4 cycles, from 20 to 2,000 Hz in each direction (x,y,z), 48 minutes, using peak acceleration of 20g (+20%, -0%). (MIL 883E, method 2007.2, A) Tested to 8kV direct contact discharge or 15kV air discharge as specified by IEC 1000-4-2, level 3 and level 4. Microphone is tested to 5 passes through reflow oven under conditions of 260C for 30 seconds maximum. Tested to 5,000g (IEC 68-2-27, Ea). Electrostatic Discharge Reflow Mechanical Shock Knowles Acoustics www.knowlesacoustics.com Rev H SP0103NC3 Recommended Interface Circuit for SP0103N Integrated Amplifier V+ Term 4 = Vdd Vout Term 1 = Output R1 = 22k R2 = 2.4k Term 3 = Ground Term 2 = Gain Control R3 (set by customer) C1 (set by customer) Desired Gain Unity Gain (0dB) 20dB Gain Adjustable Gain Pin 2 Termination Method Tie Terminal 2 directly to Output (Terminal 1). Tie Terminal 2 through C1 (0.47uF) to Ground. Add R3 and C1. Use formulas provided to calculate settings, or contact Knowles for support. Setting Gain Formulas: Gain of non-inverting Op-Amp is determined as: G=1+ {R1 / (R2 + R3)} Gain(dB) = 20 * log(G) High-pass-filter Corner Frequency: C.F. = 1 / {2*pi*(R2 + R3) * C1} Knowles Acoustics www.knowlesacoustics.com Rev H SP0103NC3 |
Price & Availability of SP0103NC3-2
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |