View FTRJ1619P1BCL_4624006.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Finisar
Product Specification 2 Gigabit Long-Wavelength Pluggable SFP Transceiver FTRJ1619P1xCL
PRODUCT FEATURES * * * * * * * * * * * Up to 2.125Gb/s bi-directional data links Hot-pluggable SFP footprint Built-in digital diagnostic functions Uncooled 1550nm DFB laser transmitter APD Receiver Duplex LC connector Very low jitter Metal enclosure, for lower EMI Single 3.3V power supply Low power dissipation <700mW typical Extended operating temperature range: -10C to 70C APPLICATIONS * * Gigabit Ethernet 1X and 2X Fibre Channel
Finisar's FTRJ1619P1xCL Small Form Factor Pluggable (SFP) transceivers are compatible with the Small Form Factor Pluggable Multi-Sourcing Agreement (MSA). They comply with Gigabit Ethernet as specified in IEEE Std 802.3 and Fibre Channel FC-PI 13.0. Digital diagnostics functions are available via the 2-wire serial bus specified in the SFP MSA. PRODUCT SELECTION
FTRJ1619P1xCL
x W B Wide Extraction Bail Narrow Extraction Bail
Finisar Corporation December 16, 2003 RevD
Page 1
FTRJ1619P1xCL Pluggable SFP Product Specification - December 2003
Finisar
I.
Pin 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Pin Descriptions
Symbol VEET TFAULT TDIS MOD_DEF(2) MOD_DEF(1) MOD_DEF(0) Rate Select LOS VEER VEER VEER RDRD+ VEER VCCR VCCT VEET TD+ TDVEET Name/Description Transmitter Ground (Common with Receiver Ground) Transmitter Fault. Not supported. Transmitter Disable. Laser output disabled on high or open. Module Definition 2. Data line for Serial ID. Module Definition 1. Clock line for Serial ID. Module Definition 0. Grounded within the module. No connection required Loss of Signal indication. Logic 0 indicates normal operation. Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Ground (Common with Transmitter Ground) Receiver Inverted DATA out. AC Coupled Receiver Non-inverted DATA out. AC Coupled Receiver Ground (Common with Transmitter Ground) Receiver Power Supply Transmitter Power Supply Transmitter Ground (Common with Receiver Ground) Transmitter Non-Inverted DATA in. AC Coupled. Transmitter Inverted DATA in. AC Coupled. Transmitter Ground (Common with Receiver Ground) Ref. 1 2 3 3 3 4 5 1 1 1
1
1
1
Notes: 1. Circuit ground is internally isolated from chassis ground. 2. Laser output disabled on TDIS >2.0V or open, enabled on TDIS <0.8V. 3. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. MOD_DEF(0) pulls line low to indicate module is plugged in. 4. Finisar FTRJxx21xxxxx transceivers operate between OC-3 and OC-48, 1x and 2x Fibre Channel, and Gigabit Ethernet data rates and respective protocols without active control. Finisar FTRJxx19xxxxx transceivers operate at 1x and 2x Fibre Channel, and Gigabit Ethernet data rates and respective protocols without active control. 5. LOS is open collector output. Should be pulled up with 4.7k - 10kohms on host board to a voltage between 2.0V and 3.6V. Logic 0 indicates normal operation; logic 1 indicates loss of signal.
VeeT 1 2 3 4 VeeT TDTXFault TD+ TX Disable VeeT MOD-DEF(2) VccT 16 15 14 13 12 11 MOD-DEF(1) VccR 6 7 8 9 10 MOD-DEF(0) VeeR Rate Select RD+ LOS RDVeeR VeeR VeeR 17 18 19 20
Towards Bezel
5
Towards ASIC
Diagram of Connector Block Pinout on the Host Board
Finisar Corporation December 16, 2003 RevD
Page 2
FTRJ1619P1xCL Pluggable SFP Product Specification - December 2003
Finisar
II.
Absolute Maximum Ratings
Symbol Vcc TS TOP RH Min -0.5 -40 -10 0 Typ Max 4.5 85 70 85 Unit V C C % Ref.
Parameter Maximum Supply Voltage Storage Temperature Case Operating Temperature Relative Humidity
1
III.
Electrical Characteristics (TOP = -10 to 70 C, VCC = 3.00 to 3.60 Volts)
Symbol Vcc Icc Rin Vin,pp VD VEN Min 3.00 Typ 230 100 250 Vcc - 1.3 Vee 1200 Vcc Vee+ 0.8 10 400 100 100 800 175 175 VccHOST Vee+0.5 51.7 122.4 Max 3.60 300 Unit V mA mV V V us mV ps ps V V mVpp ps ps Ref.
Parameter Supply Voltage Supply Current Transmitter Input differential impedance Single ended data input swing Transmit Disable Voltage Transmit Enable Voltage Transmit Disable Assert Time Receiver Single ended data output swing Data output rise time Data output fall time LOS Fault LOS Normal Power Supply Rejection Deterministic Jitter Contribution Total Jitter Contribution
2
3
Vout,pp tr tf VLOS fault VLOS norm PSR RX DJ RX TJ
300
Vcc - 0.5 Vee 100
4 5 5 6 6 7 8
Notes: 1. Non Condensing. 2. Connected directly to TX data input pins. AC coupled thereafter. 3. Or open circuit. 4. Into 100 ohms differential termination. 5. 20 - 80 % 6. Loss Of Signal is LVTTL. Logic 0 indicates normal operation; logic 1 indicates no signal detected. 7. Receiver sensitivity is compliant with power supply sinusoidal modulation of 20 Hz to 1.5 MHz up to specified value applied through the recommended power supply filtering network. 8. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and DJ.
Finisar Corporation December 16, 2003 RevD
Page 3
FTRJ1619P1xCL Pluggable SFP Product Specification - December 2003
Finisar
IV.
Optical Characteristics (TOP = -10 to 70C, VCC = 3.00 to 3.60 Volts)
Symbol POUT ER OMA SSRmin tr/ tf RIN RX DJ RX TJ RSENS1 RSENS2 RSENS1 PMAX C LOSD LOSA -9 1270 -41 0.5 Min 0 1540 9 174 30 180 -120 51.7 122.4 -28 -30 -30 1600 -28 Typ Max +5 1570 1 Unit dBm nm nm dB W dB ps dB/Hz ps ps dBm dBm dBm dBm nm dBm dBm dB Ref. 1
Parameter Transmitter Output Opt. Pwr: 9/125 SMF Optical Wavelength Spectral Width (-20dB) Optical Extinction Ratio Optical Modulation Amplitude Sidemode Supression ratio Optical Rise/Fall Time Relative Intensity Noise Deterministic Jitter Contribution Total Jitter Contribution Receiver Average Rx Sensitivity @ 2.125 Gb/s (2X Fibre Channel) Average Rx Sensitivity @ 1.25 Gb/s (Gigabit Ethernet) Average Rx Sensitivity @ 1.062 Gb/s (1X Fibre Channel) Maximum Input Power Optical Center Wavelength LOS De-Assert LOS Assert LOS Hysteresis
2 3 4
5, 6 5, 6 5, 6
Notes: 1. Class 1 Laser Safety per FDA/CDRH and EN (IEC) 60825 regulations. 2. Equivalent extinction ratio specification for Fibre Channel. Allows smaller ER at higher average power. 3. Unfiltered, 20-80%. Complies with IEEE 802.3 (Gig. E), FC 1x and 2x eye masks when filtered. 4. Measured with DJ-free data input signal. In actual application, output DJ will be the sum of input DJ and DJ. 5. Measured with conformance signals defined in FC-PI 13.0 specifications. 6. Measured with PRBS 27-1 at 10-12 BER
Finisar Corporation December 16, 2003 RevD
Page 4
FTRJ1619P1xCL Pluggable SFP Product Specification - December 2003
Finisar
V.
General Specifications
Symbol BR BER LMAX2 LMAX3 Min 1062 Typ Max 2125 10-12 Units Mb/s km km Ref. 1 2 3 3
Parameter Data Rate Bit Error Rate Max. Supported Link Length on 9/125m SMF @ 2X Fibre Channel Max. Supported Link Length on 9/125m SMF @ 1X Fibre Channel or Gigabit Ethernet
104 112
Notes: 1. Gigabit Ethernet and 1x/2x Fibre Channel compliant. 2. Tested with a PRBS 27-1 test pattern. 3. Attenuation of 0.25 dB/km is used for the link length calculations. Distances are indicative only. A 2dB penalty is included for dispersion on >2Gb/s data rates. Please refer to the Optical Specifications in Table IV to calculate a more accurate link budget based on specific conditions in your application.
VI.
Environmental Specifications
Finisar SFP transceivers have an extended operating temperature range from -10C to +70C case temperature.
Parameter Case Operating Temperature Storage Temperature Symbol Top Tsto Min -10 -40 Typ Max 70 85 Units C C Ref.
VII.
Regulatory Compliance
Finisar transceivers are Class 1 Laser Products and comply with US FDA regulations. These products are certified by TUV and CSA to meet the Class 1 eye safety requirements of EN (IEC) 60825 and the electrical safety requirements of EN (IEC) 60950. Copies of certificates are available at Finisar Corporation upon request.
Finisar Corporation December 16, 2003 RevD
Page 5
FTRJ1619P1xCL Pluggable SFP Product Specification - December 2003
Finisar
VIII. Digital Diagnostic Functions Finisar FTRJ1619P1xCL SFP transceivers support the 2-wire serial communication protocol as defined in the SFP MSA1. It is very closely related to the E2PROM defined in the GBIC standard, with the same electrical specifications. The standard SFP serial ID provides access to identification information that describes the transceiver's capabilities, standard interfaces, manufacturer, and other information. Additionally, Finisar SFP transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range. The SFP MSA defines a 256-byte memory map in E2PROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h). The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged. The interface is identical to, and is thus fully backward compatible with both the GBIC Specification and the SFP Multi Source Agreement. The complete interface is described in Finisar Application Note AN2030: "Digital Diagnostics Monitoring Interface for SFP Optical Transceivers". The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially. For more information, please see the SFP MSA documentation1 or Finisar Application Note AN-2030. Digital diagnostics for the FTRJ1619P1xCL are externally calibrated by default. Please note that evaluation board FDB-1018 is available with Finisar ModDEMO software that allows simple to use communication over the 2-wire serial interface.
Finisar Corporation December 16, 2003 RevD
Page 6
FTRJ1619P1xCL Pluggable SFP Product Specification - December 2003
Finisar
IX.
Mechanical Specifications
Finisar's Small Form Factor Pluggable (SFP) transceivers are compatible with the dimensions defined by the SFP Multi-Sourcing Agreement (MSA) 3.
FTRJ1619P1BCL
Finisar Corporation December 16, 2003 RevD
Page 7
FTRJ1619P1xCL Pluggable SFP Product Specification - December 2003
Finisar
FTRJ1619P1WCL
Finisar Corporation December 16, 2003 RevD
Page 8
FTRJ1619P1xCL Pluggable SFP Product Specification - December 2003
Finisar
X.
PCB Layout and Bezel Recommendations
Finisar Corporation December 16, 2003 RevD
Page 9
FTRJ1619P1xCL Pluggable SFP Product Specification - December 2003
Finisar
Finisar Corporation December 16, 2003 RevD
Page 10
FTRJ1619P1xCL Pluggable SFP Product Specification - December 2003
Finisar
XI. 1. 2. 3. 4.
References Small Form Factor Pluggable (SFP) Transceiver Multi-Source Agreement (MSA), September 2000. Documentation is currently available at Finisar upon request. Telcordia GR-253 and ITU-T G.957 Specifications (Transmitter Optical Output Power complies with SONET OC-48 requirements only). IEEE Std 802.3, 2002 Edition, Clause 38, PMD Type 1000BASE-LX. IEEE Standards Department, 2002. (*) "Fibre Channel Draft Physical Interface Specification (FC-PI 13.0)". American National Standard for Information Systems. (*)
(*) Neither IEEE 802.3 nor FC-PI 13.0 specifies a 1550nm DFB single mode interface. The FTRJ1619P1xCL complies with these standards except for receiver sensitivity, and transmit output power. See Section IV for details.
XII.
For More Information
Finisar Corporation 1308 Moffett Park Drive Sunnyvale, CA 94089-1133 Tel. 1-408-548-1000 Fax 1-408-541-6138 sales@finisar.com www.finisar.com
Finisar Corporation December 16, 2003 RevD
Page 11

▲Up To Search▲

Price & Availability of FTRJ1619P1BCL

	To Download FTRJ1619P1BCL Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .